Moxa Industrial Media Converter PTC-101 Hardware Installation Guide Second Edition, February 2010 © 2010 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan, R.O.C.
Overview Moxa Industrial Media Converter, which is specially designed for reliable and stable operation in harsh industrial environments, provides industrial grade media conversion between 10/100BaseT(X) and 100BaseFX. PTC-101’s reliable industrial design is excellent for keeping your industrial automation applications running continuously, and comes with a relay output warning alarm to help prevent damages and losses.
Panel Layout of PTC-101 Series Top Panel View 2 Terminal block for power 3. 3 3 4 4 Grounding screw 2. input 1 2 1 1. Front Panel View (PTC-101-M-SC-HV) Front Panel View (PTC-101-M-ST- LV) 4. DIP switch 5. Power input PWR LED 6. Fiber Link/Active LED 7. 100BaseFX Port (ST/SC/LC connector) 8. 5 5 6 6 7 7 9 10 8 11 Heat dissipation vents and relay output 9 8 10 11 Rear Panel View Rear Panel View 12 12 -3- 10/100BaseT(X) 9. TP port 10 Mbps LED 10.
Dimensions (For PTC-101-M-SC-HV. Others are provided by requests.) 67.4 mm (2.65 in) 15 mm (0.59 in) 42.4 mm (1.67 in) 40 mm (1.57 in) 19 mm (0.75 in) 19 mm (0.75 in) 144.15 mm (5.68 in) 144.15 mm (5.68 in) 101.4 mm (3.99 in) 111.4 mm (4.39 in) 123.46 mm (4.86 in) 101.4 mm (3.99 in) 12.06 mm (0.47 in) 111.4 mm (4.39 in) 123.46 mm (4.86 in) Side View (HV Models) Side View (LV Models) 26.2 mm (1.03 in) 135.1 mm (5.32 in) 30.5 mm (1.2 in) 26.06 mm (1.03 in) 66.65 mm (2.62 in) 67 mm (2.
You should also pay attention to the following points: y Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.
ATTENTION Before connecting PTC-101-LV to the DC power inputs, make sure the DC power source voltage is stable. Communication Connections PTC-101 models have one 10/100BaseT(X) Ethernet port, and one 100BaseFX (SC, ST, or LC type connector) fiber port. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on PTC-101’s front panel are used to connect to Ethernet-enabled devices.
100BaseFX Ethernet Port Connection The concept behind the SC port and cable is quite straightforward. Suppose you are connecting devices I and II. Contrary to electrical signals, optical signals do not require a circuit in order to transmit data. Consequently, one of the optical lines is used to transmit data from device I to device II, and the other optical line is used transmit data from device II to device I, for full-duplex transmission.
DIP Switch Setting ON 1 DIP 2 3 4 5 DIP No. Function ON OFF 1 Auto Negotiation Enable Disable “ON”: Enables “Auto Negotiation” function, the speed and duplex states for each port link segment are automatically configured using the highest performance interoperation mode. “OFF”: Disables “Auto Negotiation” function, the speed and duplex states depend on the manual setting configuration. 2 Force TP Speed 100Mbps 10Mbps (Only when Auto Negotiation is disabled) “ON”: Forces 100Mbps on Ethernet port.
LED Indicators The front panel of Moxa Industrial Media Converter contains several LED indicators. The function of each LED is described in the table below.
Dip Switches: Dip No. Function ON 1 Auto Negotiation Enable 2 Force TP Speed 100 Mbps 3 Force TP Duplex Full Duplex 4 Link Fault Pass Throuth Enable 5 Operating Mode Store-and-Forward Default DIP settings are all at ON position. Alarm Contact OFF Disable 10 Mbps Half Duplex Disable Pass Through One relay output with current carrying capacity of 1 A @ 24 VDC Optical Fiber: 100BaseFX Multi-mode Single-mode 1300 nm 1310 nm Wavelength -10 dBm 0 dBm Max. TX -20 dBm -5 dBm Min.
Regulatory Approvals Safety UL 60950-1 EMI FCC Part 15, CISPR (EN55022) class A EMS EN61000-4-2 Edition 1.2: 2001-04 (Level 4) EN61000-4-3: 1995+A1: 2001 IEC 61000-4-3: 2002+A1: 2002 (Level 3) EN61000-4-4: 2004 (Level 4) EN61000-4-5: 2001-04 (Level 4) EN61000-4-6: 2004-11 (Level 3) EN61000-4-8: 2001-03 (Level 5) EN61000-4-11: 2004-03 (Criteria B) Power Automation IEC 61850-3, IEEE 1613 Rail Traffic EN50155/EN50121-4 Warranty 5 years Details: See www.moxa.
