Moxa PowerTrans Switch PT-7710 Series Hardware Installation Guide Third Edition, July 2010 © 2010 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan, R.O.C.
Package Checklist The Moxa PowerTrans switch is shipped with the following items. If any of these items are missing or damaged, please contact your customer service representative for assistance.
44 31.8 Dimensions (unit = mm) 195 209.4 219.3 24.3 Rear View 266.5 Top View Side View Side View 44 31.8 31.8 462.5 Front View Fast Ethernet Interface Modules (for slot 1) 40.7 PM-7200-4MSC2TX/PM-7200-4SSC2TX PM-7200-1LSC6TX 96.8 PM-7200-2MSC4TX/PM-7200-2SSC4TX PM-7200-4MST2TX 96.8 96.8 40.7 40.7 96.8 PM-7200 1MST6TX PM-7200-2MST4TX PM-7200-6MST 96.8 96.8 40.7 40.7 96.8 PM-7200 1SSC6TX/1MSC6TX PM-7200-4M12 PM-7200-8SFP 96.8 PM-7200 4MST-FL 96.8 40.7 40.7 96.8 40.
86.6 86.6 PM-7200-2GTXSFP 86.6 PM-7200 1MST 40.7 40.7 PM-7200 1MSC/1SSC 86.6 PM-7200 2MSC/2SSC 40.7 40.7 40.7 Gigabit/Fast Ethernet Interface Modules (for slot 2) 86.6 PM-7200 2MST Rack Mounting Use four screws to attach the PT switch to a standard rack. Use four screws to attach the PT switch to a standard rack. Wall Mounting Use four screws to attach the PT switch to a Moxa wall mounting kit.
Wiring the Power Inputs The PT series of switches supports dual redundant power supplies (DC power only): VDC “Power Supply 1 (PWR1)” and “Power Supply 2 (PWR2)”, or VAC “Power Supply (PWR1)”. The connections for PWR1, PWR2 and the RELAY are located on the terminal block. The front view of the terminal block connectors are shown below. Wiring the Relay Contact Each PT switch has one relay output.
LED Indicators The front panel of the PT switch contains several LED indicators. The function of each LED is described in the table below. LED Color State System LEDs System has passed self-diagnosis test on boot-up and is ready to run. On GREEN Blinking STAT RED PWR1 PWR2 FAULT MSTR/HEAD CPLR/TAIL System failed self-diagnosis on boot-up. On Power is being supplied to the main module’s power input PWR1. Off Power is not being supplied to the main module’s power input PWR1.
Blinking Off port’s link is active. The corresponding module port’s data is being transmitted. The corresponding module port’s link is inactive. The corresponding module port’s data is being transmitted at 10 Mbps. The corresponding module port’s On data is being transmitted at 100 Mbps. The corresponding module port’s Blinking data is being transmitted at 1000 Mbps. The corresponding module port’s On data is being transmitted in full duplex mode.
Indicators Mode LED Indicators Alarm Contact CPLR/TAIL LNK/ACT, FDX/HDX, RING/CHAIN PORT, COUPLER PORT, SPEED One relay output with current carrying capacity of 3A @ 30 VDC or 3A @ 240 VAC Optical Fiber (100BaseFX) Distance Multi-mode 0 to 5 km, 1300 nm (50/125μm, 800 MHz*km) 0 to 4 km, 1300 nm (62.5/125μm, 500 MHz*km) Single-mode 0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km)) Min. TX Output Multi-mode: -20 dBm; single-mode: -5 dbm Max.
