NPort IA5000A Quick Installation Guide Version 5.1, September 2019 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa Europe: Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99 Moxa Asia-Pacific: Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa India: Tel: +91-80-4172-9088 Fax: +91-80-4132-1045 2019 Moxa Inc.
Overview The NPort IA5000A series of device servers deliver easy and reliable serial-to-Ethernet connectivity for the industrial automation market. The servers support several operation modes—TCP Server, TCP Client, UDP, Real COM, RFC2217, RTelnet, Pair Connection, and Ethernet Modem—ensuring the compatibility of network software, and are an ideal choice for connecting RS-232/422/485 serial devices, such as PLCs, sensors, meters, motors, drives, barcode readers, and operator displays.
Dimensions The Reset to Default Button—Depress the Reset to default button for 5 continuous seconds to load the factory default settings. Use a pointed object, such as a straightened paper clip or toothpick, to depress the Reset to default button. This will cause the Ready LED to blink on and off. The factory default settings are loaded once the Ready LED stops blinking (after about 5 seconds). At this point, you can release the Reset to default button.
NPort IA5000A Series LED Indicators (front panel) Name PWR1, PWR2 Color Function Power is being supplied to power input PWR1, PWR2. Red Red Ready Green Off Orange E1, E2 Green Off Orange P1, P2, Green P3, P4 Off Steady on: Power is on and the NPort IA5000A Series is booting up. Blinking: Indicates an IP conflict, the DHCP or BOOTP server did not respond properly, or a relay output occurred. Steady on: Power is on and the NPort IA5000A Series is functioning normally.
The following figure illustrates the two mounting options: Software Installation Information For the NPort’s configuration, the default IP address of the NPort is: 192.168.127.254. You may log in with the account name admin and password moxa to change any setting to meet your network topology (e.g., IP address) or serial device (e.g., serial parameters). For software installation, download the relative utilities from Moxa's website https://www.moxa.com/support/support_home.
RS-422/2W RS-485/4W RS-485 (Terminal Block) Pinouts RS-485 (2W) – – Data+(B) Data-(A) GND PIN 1 2 3 4 5 RS-422/ RS-485 (4W) TxD+(B) TxD-(A) RxD+(B) RxD-(A) GND Four cables are available as optional accessories that can be used to connect the NPort IA5000A Series to RS-232 serial devices. For your convenience, we show precise cable wiring diagrams for each of the two cables. Female DB9 to Male DB9 Female DB9 to Male DB25 ATEX and IECEx Information 1. 2. 3.
4. Standards Covered: EN 60079-0:2012+A11:2013, IEC 60079-0 Ed 6.0, EN 60079-15:2010, IEC 60079-15 Ed 4.0 5. The conditions of safe usage: • The Ethernet Communications Devices are intended for mounting in a tool-accessible ATEX-Certified or IECEx-Certified (for models with the suffix -CT or -IEX) IP54 enclosure and used in an area of not more than pollution degree 2 as defined by IEC/EN 60664-1 or IEC 60664-1 (for models with the suffix CT or -IEX).
SW ON OFF *Default 1 Pull-high resistor 1 kΩ 150 kΩ* 2 Pull-low resistor 1 kΩ 150 kΩ* Model NPort IA5150A Series NPort IA5250A Series NPort IA5450A Series Power Input Relay Output Maximum Surrounding Air Temperature 24 VDC, 1 A, resistance 75°C 3 Terminator 120 Ω –* 12 to 48 VDC, max.
