MiiNePort E Series Quick Installation Guide Version 1.1, November 2019 Technical Support Contact Information www.moxa.
Overview The Moxa MiiNePort E series of serial-to-Ethernet embedded modules comes with four models: two standard operating temperature models (MiiNePort E, MiiNePort E-H) and two wide operating temperature models (MiiNePort E-T, MiiNePort E-H-T). Moxa provides a starter kit for each MiiNePort E series module; each starter kit contains an evaluation board that can be used to evaluate the modules and to develop your own application.
Available Starter Kits • • • • • • MiiNePort E1-ST: Starter kit for the MiiNePort E1 Series, module included MiiNePort E1-H-ST: Starter kit for the MiiNePort E1-H Series, module included MiiNePort E2-ST: Starter kit for the MiiNePort E2 Series, module included MiiNePort E2-H-ST: Starter kit for the MiiNePort E2-H Series, module included MiiNePort E3-ST: Starter kit for the MiiNePort E3 Series, module included MiiNePort E3-H-ST: Starter kit for the MiiNePort E3-H Series, module included Package Checklist E
STEP 5: Use the serial data cable to connect the evaluation board to a serial device. Software Utility Installation Procedure Use the following installation procedure for each MiiNePort E model: Software Installation For software installation, download the relevant utilities from Moxa's website: https://www.moxa.com/en/support 1. Start the Device Search Utility (DSU) setup program to begin the installation. When the Welcome window opens, click Next. 2.
E2 Series Number 1 2 3 4 5 6 7 8 9 10 11 12 13 Description MiiNePort E2 Module Location Ethernet RJ45 Connector Serial Interface Jumper Power Switch Power Jack Power and Ready LED DB9 Male Connector Serial Port Status LED Digital IO Terminal Block Digital Output LED Digital Input/Output Mode Digital Input Switch Circuit Pad -5-
E3 Series Number 1 2 3 4 5 6 7 8 9 10 11 12 13 Description PoE Pin MiiNePort E3 Module Location Serial Interface Jumper Power Switch Power Jack Power & Ready LED DB9 Male Connector Serial Port Status LED Digital IO Terminal Block Digital Output LED Digital Input/Output Mode Digital Input Switch Circuit Pad -6-
Pin Assignment E1 Series Serial Signal Pins (MiiNePort E1 Series Modules) a. Pin Function 1 GND 2 VCC 3 Reset 4 Data Out 5 Data In 6 Ready/RTSa 7 Reset to Defaultb 8 CTSc Pin 6 can be configured as Ready/RTS (RequesttoSend), Ready/DO, or RS-485 Tx Enabled (the default it Ready/RTS). b. Pin 7 can be configured as Reset to Default, DIO, DTR, or RS-485 Tx Enabled (the default is Reset to Default). c. Pin 8 can be configured as CTS (CleartoSend), DI, or DSR (the default is CTS).
Pin 1 2 3 4 5 6 7 8 9 10 Signal Name DIO0 DIO1 DIO2 DIO3 Reserved Reserved SW Reset GND Ready LED VCC JP3 Function Programmable Input/Output Programmable Input/Output Programmable Input/Output Programmable Input/Output N/A N/A Reset To Factory Default Circuit Ground System is Ready Power Supply E3 Series The bottom view of the MiiNePort E3 Series Module Pin 1 2 3 4 5 6 7 8 Pin 1 2 3 4 5 6 7 8 9 10 11 12 Ethernet Pins (JP2) Signal Name Function Reserve N/A Reserve N/A Reserve N/A Reserve N/A PoE signal
Pin 13 14 15 16 17 18 19 20 Signal Name DSR Reserve CTS SW_Reset Reserve Reserve GND VCC Function Data Set Ready N/A Clear to Send Reset to Factory Default N/A N/A Circuit Ground Power Supply Ethernet Port Pins RJ45 Pin 1 2 3 6 Signal Tx+ TxRx+ Rx- Evaluation Board Serial Port DB9 Male Pin 1 2 3 4 5 6 7 8 9 RS-232 DCD RxD TxD DTR GND DSR RTS CTS – RS-485-2W – – D+ DGND – – – – Certification This product complies with Chinese RoHS (Restriction of Hazardous Substances) regulations for Electronic Infor
