Installation guide

— 4 — — 5 — — 6 —
5. If you see a warning that the software has not passed Windows Logo
testing, select Continue Anyway.
6. After the driver software has been installed, the installation wizard
will guide you through the port installation, starting with port 0. Be
sure to install the software from the \CP-114UL\Software\Windows
2K folder on the CD.
7. To verify successful installation, use Windows Device Manager and
check under Multi-port serial adapters and Ports (COM & LPT)
for any special marks, such as a question mark or exclamation point.
Linux (32-bit/64-bit)
Ensure that you are logged into the machine with superuser (root)
privileges. Insert the Moxa driver CD-ROM into the CD-ROM drive.
If necessary, use the mkdir command to create a mount point for the
CD-ROM. The following command creates a mount point in the directory
/cdrom; you can mount the CD-ROM at any location in the machine’s
local file system.
mkdir /cdrom
The commands in the steps below assume the CD-ROM is mounted at
/cdrom. If you mount the CD-ROM at a different location, use that
location when issuing commands.
Mount the CD-ROM drive by entering the following command:
# mount -t iso9660 -o ro /dev/cdrom /cdrom
1. Execute the following commands from the Linux prompt:
#mount /dev/cdrom /mnt/cdrom
#cd /
#mkdir moxa
#cd moxa
#cp /mnt/cdrom/<driver directory>/mxser.tgz .
#tar xvfz mxser.tgz
#cd mxser
#make clean; make install
#cd /moxa/mxser/driver
#./msmknod
#modprobe mxser
2. Use the Moxa diagnostic utility to verify the driver status:
#cd /moxa/mxser/utility/diag
#./msdiag
3. Use the Moxa terminal utility to test the TTY ports:
#cd /moxa/mxser/utility/term
#./msterm #./msterm
5. Pin Assignments and Cable Wiring
The CP-112UL series has a female DB25 connector on the board. Cables
with different connectors are available to help you connect your device to
the board.
Male DB9 (CBL-M25M9x2-50)
15
69
Pin RS-232 RS-422 RS-485 4-wire RS-485 2-wire
1 DCD TxD-(A) TxD-(A) ---
2 RxD TxD+(B) TxD+(B) ---
3 TxD RxD+(B) RxD+(B) Data+(B)
4 DTR RxD-(A) RxD-(A) Data-(A)
5 GND GND GND GND
6 DSR --- --- ---
7 RTS --- --- ---
8 CTS --- --- ---
The CP-114UL series has a female DB44 connector on the board. Cables
with different connectors are available to help you connect your device to
the board.
Male DB9 (CBL-M44M9x4-50)
15
69
Pin RS-232 RS-422 RS-485 4-wire RS-485 2-wire
1 DCD TxD-(A) TxD-(A) ---
2 RxD TxD+(B) TxD+(B) ---
3 TxD RxD+(B) RxD+(B) Data+(B)
4 DTR RxD-(A) RxD-(A) Data-(A)
5 GND GND GND GND
6 DSR --- --- ---
7 RTS --- --- ---
8 CTS --- --- ---
Male DB25 (CBL-M44M25x4-50)
1
14
13
25
Pin RS-232 RS-422 RS-485 4-wire RS-485 2-wire
2 TxD RxD+(B) RxD+(B) Data+(B)
3 RxD TxD+(B) TxD+(B) ---
4 RTS --- --- ---
5 CTS --- --- ---
6 DSR --- --- ---
7 GND GND GND GND
8 DCD TxD-(A) TxD-(A) ---
20 DTR RxD-(A) RxD-(A) Data-(A)
Click here for online support:
www.moxa.com/support
The Americas: [phone] (toll-free: 1-888-669-2872)
Europe: [phone]
Asia-Pacific: [phone]
China: [phone] (toll-free: 800-820-5036)
© 2009 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.