User`s manual
Table Of Contents
- 1. Introduction
- 2. Getting Started
- Starting Your UC-7400-CE Computer
- Resetting Your UC-7400-CE Computer
- Operating UC-7400-CE Computer Via Serial Console
- Changing the Network Settings
- Operating Your UC-7400-CE Computer Via Telnet Client
- User/Group Management
- Adjusting System Time and RTC Time
- Starting and Stopping Services
- Troubleshooting Network Connectivity
- Simple Network Management Protocol (SNMP)
- 3. Web-based Management System
- 4. Application Development
- 5. Programming Examples
- A. Operating Programmable Function Keys and LCM
- B. Firmware Upgrade Procedure
- C. Service Information
UC-7400-CE User’s Manual Introduction
1-2
Overview
The MOXA UC-7400-CE Series (herein after referred to as UC-7400-CE) includes UC-7420-CE,
UC-7410-CE, and UC-7408-CE. These RISC-based ready-to-run embedded computers are ideal
for embedded applications. UC-7400-CE features 8 RS-232/422/485 serial ports, dual 10/100
Mbps Ethernet ports, 8 digital input channels and 8 digital output channels, a PCMCIA interface
for wireless LAN communication, a CompactFlash port for flash disk expansion, and USB ports
for adding additional memory (such as a USB Flash disk).
UC-7400-CE uses an Intel XScale IXP-422 266 MHz RISC CPU. Unlike the X86 CPU, which
uses a CISC design, the IXP-422’s RISC design architecture and modern semiconductor
technology provide UC-7400-CE with a powerful computing engine and communication functions,
but without generating a lot of heat. The built-in 32 MB NOR Flash ROM and 128 MB SDRAM
give you enough memory to run your application software directly on UC-7400. As the dual LAN
ports are built right into the IXP-422 CPU, UC-7400-CE makes an ideal communication platform
for Network Security applications. If your application requires placing UC-7400-CE at a site that
is not located near an Ethernet LAN connection, you can connect to the network by using
UC-7400’s PCMCIA port to attach a wireless LAN card.
UC-7400-CE series ready-to-run embedded computers are built on Microsoft® Windows® CE 5.0
operating system (OS). Building on a common, widely used environment makes them suitable for
new system development and legacy system migration.
All the necessary device drivers, such as a PCMCIA Wireless LAN module and Keypad, LCM,
and Buzzer control, are included with UC-7400-CE. The Operating System, device drivers, and
the software you develop for your own application, can all be stored in UC-7400’s Flash memory.
Model Descriptions and Package Checklist
The basic features of each UC-7400-CE product are described below:
UC-7420-CE
RISC-based ready-to-run embedded computer with 8 Serial Ports, Dual Ethernet, PCMCIA,
CompactFlash, USB, WinCE 5.0
UC-7410-CE
RISC-based ready-to-run embedded computer with 8 Serial Ports, Dual Ethernet, WinCE 5.0
UC-7408-CE
RISC-based Data Acquisition embedded computer with 8 Serial Ports, 8 DI Channels, 8 DO
Channels, Dual Ethernet, PCMCIA, CompactFlash, WinCE 5.0
UC-7400-CE is shipped with the following items:
y 1 UC-7400 series embedded computer
y Wall-Mounting Kit
y DIN-Rail Mounting Kit
y Quick Installation Guide
y Document & Software CD
y Cross-over Ethernet cable
y CBL-RJ45M9-150: 150 cm, 8-pin RJ45 to Male DB9 serial port cable
y CBL-RJ45F9-150: 150 cm, 8-pin RJ45 to Female DB9 console port cable
y Universal Power Adaptor
y Product Warranty Booklet
NOTE: Notify your sales representative if any of the above items is missing or damaged.