TN-5510-2GLSX-ODC Hardware Installation Guide Moxa ToughNet Switch Second Edition, August 2013 2012 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
Overview The ToughNet TN-5510-2GLSX-ODC series M12 managed Ethernet switches are designed for industrial applications in harsh environments. The TN series switches use M12 connectors to ensure tight, robust connections, and guarantee reliable operation against environmental disturbances, such as vibration and shock. The switch supports a power input range 12/24/36/48 VDC.
• • • • • • • Lock port allows access by only authorized MAC addresses. Port mirroring for online debugging. Automatic warning by exception through email, relay output. Automatic recovery of connected device’s IP addresses. Line-swap fast recovery. LLDP for automatic topology discovery in network management software. Configurable through Web browser, Telnet/Serial console, and Windows utility.
TN-5510-2GLSX-ODC Panel Layouts 1. 2. 3. 4. 5. 6. 7. 3 Rotary switches and protective cover with Model name. Screw holes for panel mounting kit. Console port. Grounding screw. Relay output port. Power input voltage range indication. Power input port (male 6-pin shielded M23 connector).
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. PWR1 LED: for power input 1. PWR2 LED: for power input 2. FAULT LED. MSTR/HEAD LED: for ring master or chain head. CPLR/TAIL LED: for ring coupler or chain tail. TP port’s 10/100 Mbps LED. 10/100BaseT(X) port (female 4-pin shielded M12 connector with D coding). Waterproof vent. Product label. 12 Screw holes for DIN-Rail mounting kit. E2 LED: Down-side E2 Gigabit port's 1000 Mbps LED. E1 LED: Down-side E1 Gigabit port's 1000 Mbps LED.
Mounting Dimensions (unit = mm) TN-5510-2GLSX-ODC Series -6-
Panel/Wall Mounting STEP 1: Mounting the TN-5510 to a wall requires 4 screws. Use the ToughNet switch as a guide to mark the correct positions of the 4 screws. STEP 2: Use the 4 screws in the panel mounting kit. If you would like to use your own screws, make sure the screw head is between 6.0 mm and 7.0 mm in diameter and the shaft is less than 4.0 mm in diameter, as shown at the right.
DIN-Rail Mounting (optional) Use a pair of optional DK-DC50131 DIN-Rail mounting kits (must be purchased separately) to mount the TN-5510 on a 35 mm DIN-Rail. STEP 1: Use 12 screws (6 screws per plate) to attach the two DIN-Rail attachment plates to the rear panel of the switch STEP 2: If the spring-loaded bracket is locked in place, push the recessed button to release it.
Wiring Requirements WARNING Turn the power off before disconnecting modules or wires. The correct power supply voltage is listed on the product label. Check the voltage of your power source to make sure you are using the correct voltage. Do NOT use a voltage greater than what is specified on the product label. These devices must be supplied by a SELV source as defined in the Low Voltage Directive 2006/95/EC and 2004/108/EC.
ATTENTION This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Connecting the Power Supplies The ToughNet TN-5510 switches support two sets of power supplies—power input 1 and power input 2.The M23 6-pin male connector on the TN-5510’s front panel is used for the dual power inputs. Use a power cord with an M23 6-pin female connector to connect the power inputs to the switch.
STEP 1: Plug your power cord’s M23 connector to the power input port of the TN-5510 switch. STEP 2: Screw the nut on your power cord connector to the power input connector on the switch to ensure a tight connection. ATTENTION Before connecting the TN-5510 to the power input, make sure the power source voltage is stable. Connecting the Relay Outputs Each TN-5510 switch has two sets of relay outputs—relay output 1 and relay output 2.
Connecting the Data Lines 10/100BaseT(X) Ethernet Port Connection All TN-5510 models have 8 10/100BaseT(X) Ethernet ports (4-pin shielded M12 connector with D coding). The 10/100Base-TX ports located on the TN-5510 front panel are used to connect to Ethernet-enabled devices.
M12 (4-pin, M) to M12 (4-pin, M) Straight-Trough Cable Wiring M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring M12 (4-pin, M) to RJ45 (8-pin) Straight-Trough Cable Wiring Rotary Switch IP Address Settings The ToughNet TN-5510 switches have 3 rotary switches on the front panel for configuring the IP address without using a PC, making onsite configuration extremely convenient. This can be especially helpful when you need to replace a faulty switch quickly.
NOTE 1. 2. 3. 4. 5. “Hardware-based IP configuration” only supports IPv4 address settings. “Hardware-based IP configuration” is enabled only when the 3 rotary switches are set to values ranging from 001 to 254. The ToughNet switch’s IP address will be configured as “192.168.127.xxx”, where “xxx” are valid value numbers set by the rotary switches. When enabled, “Hardware-based IP configuration” overrides the “Auto IP Configuration” described in the “IP Settings” section in the user’s manual.
OFF CPLR/ TAIL GREEN ON Blinking OFF Ports LEDs TP AMBER (10/100M) GREEN E1/E2 (1000M) GREEN ON Blinking Off On Blinking off On Blinking Off When the TN switch is neither the Master of this Turbo Ring, nor the Head of this Turbo Chain. When the TN switch enables the coupling function to form a back-up path in this Turbo Ring, or it is the Tail of this Turbo Chain. When the Turbo Chain is down. When the TN switch disables the coupling function of Turbo Ring, or it is not the Tail of the Turbo Chain.
Interface Fast Ethernet Front cabling, M12 connector, 10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X connection Gigabit Ethernet Down cabling, M12 connector, 1000BaseLSX Console Port M12 A-coding 5-pin male connector System LED Indicators PWR1, PWR2, FAULT, MSTR/HEAD, CPLR/TAIL Port LED Indicators 10/100M (Fast Ethernet port), 1000M (Gigabit Ethernet port) Alarm Contact Two relay outputs in one M12 A-coding 5-pin male connector with current carrying capacity of 3 A @ 30 VDC or 3
Technical Support Contact Information www.moxa.
