Moxa PowerTrans Switch PT-G7509 User’s Manual www.moxa.com/product First Edition, December 2009 © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
Moxa PowerTrans Switch PT-G7509 User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks Moxa is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers.
Table of Contents Chapter 1 Introduction ...............................................................................................1-1 Overview .............................................................................................................................. 1-2 Package Checklist................................................................................................................. 1-2 Software Features ..............................................................................
GMRP Table ........................................................................................................... 3-64 Using Bandwidth Management .......................................................................................... 3-65 Using Port Access Control.................................................................................................. 3-65 Configuring Static Port Lock ..................................................................................
1 Chapter 1 Introduction Welcome to the PowerTrans PT-G7509, a managed redundant Gigabit Ethernet switch designed especially for connecting Ethernet-enabled devices for industrial field applications.
PT-G7509 User’s Manual Introduction Overview The PowerTrans PT-G7509 is equipped with 9 Combo Gigabit Ethernet ports, making it ideal for upgrading an existing network to Gigabit speeds and building a new full Gigabit backbone. The PT-G7509 is designed to meet the demands of power substation automation systems (IEC 61850-3, IEEE 1613), traffic control systems (NEMA TS 2), and railway applications (EN50121-4).
PT-G7509 User’s Manual Introduction 1-3
2 Chapter 2 Getting Started This chapter explains how the initial installation process for the PT-G7509. There are three ways to access the PT-G7509’s configuration settings: the serial console, Telnet console, and web console. If you do not know the PT-G7509’s IP address, you can open the serial console by connecting the PT-G7509 to a PC’s COM port with a short serial cable. You can open the Telnet or web console over an Ethernet LAN or over the Internet.
PT-G7509 User’s Manual Getting Started Serial Console Configuration (115200, None, 8, 1, VT100) NOTE NOTE y You cannot connect to the serial and Telnet console at the same time. y You can connect to the web console and another console (serial or Telnet) at the same time. However, it is strongly recommended that you do NOT do so. Following this advice will allow you to maintain better control over the PT-G7509’s configuration.
PT-G7509 User’s Manual Getting Started 3. The Property window should open. On the Communication Parameter tab for Ports, select the COM port that is being used for the console connection. Set the other fields as follows: 115200 for Baud Rate, 8 for Data Bits, None for Parity, and 1 for Stop Bits. 4. On the Terminal tab, select VT100 for Terminal Type. Click OK. 5. In the terminal window, the PT-G7509 will prompt you to select a terminal type. Enter 1 to select ansi/vt100 and press Enter.
PT-G7509 User’s Manual Getting Started 6. The serial console will prompt you to log in. Press Enter and select admin or user. Use the down arrow key on your keyboard to select the Password field and enter a password if desired. This password will be required to access any of the consoles (web, serial, Telnet). If you do not wish to create a password, leave the Password field blank and press Enter. 7. The Main Menu of the PT-G7509’s serial console should appear.
PT-G7509 User’s Manual Getting Started Configuration by Telnet Console You may open the PT-G7509’s Telnet or web console over a network. This requires that the PC host and the PT-G7509 are on the same logical subnet. You may need to adjust your PC host’s IP address and subnet mask. By default, the PT-G7509’s IP address is 192.168.127.253 and the PT-G7509’s subnet mask is 255.255.0.0 (for a Class B network). This means that your PC's IP address must be set to 192.168.xxx.xxx for a subnet mask of 255.255.0.
PT-G7509 User’s Manual Getting Started 3. The Telnet console will prompt you to log in. Press Enter and select admin or user. Use the down arrow key on your keyboard to select the Password field and enter a password if desired. This password will be required to access any of the consoles (web, serial, Telnet). If you do not wish to create a password, leave the Password field blank and press Enter. 4. The Main Menu of the PT-G7509’s Telnet console should appear. 5.
PT-G7509 User’s Manual 7. Getting Started Use the following keys on your keyboard to navigate the PT-G7509’s Telnet console: Key Up, down, right, left arrow keys, Tab Enter Space Esc NOTE Function Move the onscreen cursor Display and select options Toggle options Previous menu The Telnet console looks and operates in precisely the same manner as the serial console.
PT-G7509 User’s Manual Getting Started After making sure that the PT-G7509 is connected to the same LAN and logical subnet as your PC, open the PT-G7509’s web console as follows: NOTE 1. Point your web browser to the PT-G7509’s IP address by entering it in the Address or URL field. 2. The PT-G7509’s web console will open, and you will be prompted to log in. Select the login account (admin or user) and enter the Password.
PT-G7509 User’s Manual Getting Started Disabling Telnet and Browser Access If you are connecting the PT-G7509 to a public network but do not intend to manage it over the network, we suggest disabling both the Telnet and web consoles. This is done through the serial console, by navigating to System Identification under Basic Settings.
3 Chapter 3 Featured Functions This chapter explains how to access the PT-G7509’s various configuration, monitoring, and administration functions. These functions can be accessed by serial, Telnet, or web console. The serial console can be used if you do not know the PT-G7509’s IP address and requires that you connect the PT-G7509 to a PC COM port. The Telnet and web consoles can be opened over an Ethernet LAN or the Internet. The web console is the most user-friendly way to configure the PT-G7509.
PT-G7509 User’s Manual Featured Functions Configuring Basic Settings Basic Settings includes the most common settings required by administrators to maintain and control the PT-G7509. System Identification System Identification items are displayed at the top of the web console and will be included in alarm emails. You can set the System Identification items to make it easier to identify different switches that are connected to your network. Switch Name Setting Max.
PT-G7509 User’s Manual Featured Functions Maintainer Contact Info Setting Max. 30 characters Description This option is useful for providing information about who is responsible for maintaining this unit and how to contact this person. Factory Default None Password The PT-G7509 provides two levels of configuration access. The admin account has read/write access of all configuration parameters, and the user account has read access only.
PT-G7509 User’s Manual Featured Functions Password Setting Old password (max. 16 characters) New password (Max. 16 characters) Retype password (Max. 16 characters) Description Enter the current password Factory Default None Enter the desired new password. Leave it blank if None you want to remove the password. Enter the desired new password again. Leave it None blank if you want to remove the password. Accessible IP The PT-G7509 uses an IP address-based filtering method to control access.
PT-G7509 User’s Manual Featured Functions The following table shows additional configuration examples: Hosts That Need Access Any host 192.168.1.120 192.168.1.1 to 192.168.1.254 192.168.0.1 to 192.168.255.254 192.168.1.1 to 192.168.1.126 192.168.1.129 to 192.168.1.254 Input Format Disable 192.168.1.120 / 255.255.255.255 192.168.1.0 / 255.255.255.0 192.168.0.0 / 255.255.0.0 192.168.1.0 / 255.255.255.128 192.168.1.128 / 255.255.255.
PT-G7509 User’s Manual Featured Functions Description Setting Media type Description This displays the media type for each module’s port Factory Default N/A Name Setting Max. 63 characters Description Specifies an alias for the port to help administrators differentiate between different ports. Example: PLC 1 Factory Default None Speed Setting Auto 100M-Full 100M-Half 10M-Full 10M-Half Description Factory Default This allows the port to use the IEEE 802.
PT-G7509 User’s Manual Featured Functions Network The Network configuration allows users to configure both IPv4 and IPv6 parameters for management access over the network. This Moxa Ethernet switch supports both IPv4 and IPv6, and can be managed through either of these address types. An explanation of each configuration item follows. IPv4 The IPv4 settings include the switch’s IP address and subnet mask, as well as the IP address of the default gateway.
PT-G7509 User’s Manual Featured Functions Switch IP Address Setting IP address for the PT-G7509 Description Assigns the PT-G7509’s IP address on a TCP/IP network. Factory Default 192.168.127.253 Switch Subnet Mask Setting Subnet mask for the PT-G7509 Description Factory Default This identifies the type of network to which the 255.255.255.0 PT-G7509 is connected (e.g., 255.255.0.0 for a Class B network, or 255.255.255.0 for a Class C network).
PT-G7509 User’s Manual Featured Functions Global Unicast Address Setting None Description Display an IPv6 Global Unicast address. The network portion of a Global Unicast address can be configured by specifying the Global Unicast Prefix and using a EUI-64 interface ID in the low order 64 bits.
PT-G7509 User’s Manual NOTE Featured Functions The PT-G7509 does not have a real time clock. The user must update the Current Time and Current Date to set the initial time for the PT-G7509 after each reboot, especially when there is no NTP server on the LAN or Internet connection. Current Time Setting User-specified time Description This allows configuration of the local time in local 24-hour format.
PT-G7509 User’s Manual Featured Functions Time Server IP/Name Setting Description IP address or name of time This is the IP or domain address (e.g., server 192.168.1.1, time.stdtime.gov.tw, or time.nist.gov). The PT-G7509 will try to locate the secondary IP address or name of NTP server if the first NTP server fails to secondary time server connect.
PT-G7509 User’s Manual Featured Functions Such an Ethernet switch will synchronize clocks directly connected to one of its ports to the highest possible accuracy.
PT-G7509 User’s Manual Featured Functions PTP Setting Operation IEEE 1588/PTP Setting Operation Description Disable or enable IEEE 1588(PTP) operation Factory Default Disabled Configuration IEEE 1588/PTP Setting Clock Mode Sync Interval Subdomain Name Description Supports software-based IEEE 1588(PTP) mode Period for sending synchronization messages (in seconds) Support _DFLT(Default) domain only Factory Default Disabled Disabled _DFLT Status Setting Offset To Master (nsec) Grandmaster UUID Parent
PT-G7509 User’s Manual Featured Functions System File Update—By Remote TFTP The PT-G7509 supports saving your configuration or log file to a remote TFTP server or local host. Other PT-G7509 switches can also load the configuration at a later time. The PT-G7509 also supports loading firmware or configuration files from the TFTP server or a local host. TFTP Server IP/Name Setting IP address of TFTP server Description Specifies the IP address or name of the remote TFTP server.
PT-G7509 User’s Manual Featured Functions System File Update—By Local Import/Export Configuration File Click Export to save the PT-G7509’s configuration file to the local host. Log File Click Export to save the PT-G7509’s log file to the local host. NOTE Some operating systems will open the configuration file and log file directly in the web page. In such cases, right click the Export button to save the file.
PT-G7509 User’s Manual Featured Functions Factory Default This function provides users with a quick way of restoring the PT-G7509’s configuration to factory defaults. This function is available in the serial, Telnet, and web consoles. NOTE After restoring the factory default configuration, you will need to use the default network settings to re-establish the web or Telnet console connection with the PT-G7509. Using Port Trunking Link aggregation involves grouping links to into a link aggregation group.
PT-G7509 User’s Manual Featured Functions To avoid broadcast storms or loops in your network while configuring a trunk, first disable or disconnect all ports that you want to add to the trunk or remove from the trunk. After you finish configuring the trunk, enable or re-connect the ports. If all ports on both switch units are configured as 100BaseTX and they are operating in full duplex mode, the potential bandwidth of the connection will be up to 1.6 Gbps.
PT-G7509 User’s Manual Featured Functions Trunk Group (Maximum of 4 trunk groups) Setting Description Trk1, Trk2, Trk3, Trk4 Specifies the current trunk group. Factory Default Trk1 Trunk Type Setting Static LACP Description Selects Moxa’s proprietary trunking protocol. Selects LACP (IEEE 802.3ad, Link Aggregation Control Protocol).
PT-G7509 User’s Manual Featured Functions Configuring SNMP The PT-G7509 supports SNMP V1, V2c, and V3. SNMP V1 and SNMP V2c use a community string match for authentication, which means that SNMP servers access all objects with read-only or read/write permissions using the community strings public and private by default. SNMP V3 requires that you select an authentication level of MD5 or SHA, and is the most secure protocol. You can also enable data encryption to enhance data security.
PT-G7509 User’s Manual Featured Functions These parameters are configured on the SNMP page. A more detailed explanation of each parameter is given below the figure. SNMP Read/Write Settings SNMP Versions Setting V1, V2c, V3, or V1, V2c, or V3 only Description Specifies the SNMP protocol version used to manage the switch. Factory Default V1, V2c V1, V2c Read Community Setting Max.
PT-G7509 User’s Manual Featured Functions V1, V2c Write/Read Community Setting Description Factory Default Specifies the community string to authenticate the SNMP agent for Max. 30 characters read/write access. The SNMP server will Private access all objects with read/write permissions using this community string. For SNMP V3, there are two levels of privilege for different accounts to access the PT-G7509. Admin privilege provides access and authorization to read and write the MIB file.
PT-G7509 User’s Manual Featured Functions User Data Encryption Key (for SNMP V1, V2c, V3 and V3 only) Setting Enable Disable Description Factory Default Enables data encryption using the specified No data encryption key (between 8 and 30 characters). No data encryption No Trap Settings SNMP traps allow an SNMP agent to notify the NMS of a significant event. The PT-G7509 supports two SNMP modes, Trap mode and Inform mode. SNMP Trap Mode In Trap mode, the SNMP agent sends an SNMPv1 trap PDU to the NMS.
PT-G7509 User’s Manual Featured Functions 1st Trap Server IP/Name Setting IP or name Description Specifies the IP address or name of the primary trap server used by your network. Factory Default None 1st Trap Community Setting Max. 30 characters Description Specifies the community string to use for authentication. Factory Default Public 2nd Trap Server IP/Name Setting IP or name Description Specifies the IP address or name of the secondary trap server used by your network.
PT-G7509 User’s Manual Featured Functions Private MIB information Switch Object ID Setting 8691.7.32 Description This indicates the PT-G7509’s enterprise value. Factory Default Fixed NOTE: The Switch Object ID cannot be changed. Using Communication Redundancy Communication redundancy on your network helps protect critical links against failure, protects against network loops, and keeps network downtime at a minimum.
PT-G7509 User’s Manual Featured Functions The Turbo Ring Concept Moxa developed the proprietary Turbo Ring protocol to optimize communication redundancy and achieve a faster recovery time on the network. The Turbo Ring and Turbo Ring V2 protocols designate one switch as the master of the network, and then automatically block packets from traveling through any of the network’s redundant loops.
PT-G7509 User’s Manual Featured Functions Turbo Ring with odd number switches Master STAT PWR1 PWR2 FAULT MASTER COUPLER LNK/ACT SPEED FDX/HDX MODE RING PORT COMUPLER PORT 1 2 3 4 5 6 7 8 If the number of Ethernet switches in the Turbo Ring is 2N+1 (an odd number), the backup segment is the (N+1)st segment counting counterclockwise. 9 For the example shown here, N=1, so that N+1=2.
PT-G7509 User’s Manual Featured Functions Ring Coupling Configuration For some systems, it may not be convenient to connect all devices in the system in a single redundant ring, since some devices could be located in a remote area. For these systems, Ring Coupling can be used to group devices into smaller redundant rings that communicate with each other.
PT-G7509 User’s Manual Featured Functions To configure the ring coupling for a Turbo Ring, select two PT series Ethernet switches (e.g., Switch A and B in the above figure) in the ring, and another two PT series Ethernet switches in the adjacent ring (e.g., Switch C and D). Select two ports on each switch to be used as coupling ports and link them together. Next, assign one switch (e.g., Switch A) to be the coupler and connect the coupler’s coupling control port with Switch B (for this example).
PT-G7509 User’s Manual Featured Functions Dual-Homing Configuration for Turbo Ring V2 Dual-homing is only supported with Turbo Ring V2 and is used to connect two networks through a single Ethernet switch. The primary path is the operating connection, and the backup path is a back-up connection that is activated in the event that the primary path connection fails.
PT-G7509 User’s Manual Featured Functions "Current Status" Items Now Active This shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP, or none. Master/Slave This indicates whether or not the PT-G7509 is the master of the Turbo Ring. This field appears only for Turbo Ring or Turbo Ring V2. NOTE The user does not need to assign the master to use Turbo Ring or Turbo Ring V2.
PT-G7509 User’s Manual Featured Functions Enable Ring Coupling Setting Description Enable Specifies that this PT-G7509 will be a ring coupler. Disable Specifies that this PT-G7509 is not a ring coupler. Factory Default Not checked Coupling Port Setting Coupling Port Description Specifies which port on the PT-G7509 will be used as the coupling port.
PT-G7509 User’s Manual NOTE Featured Functions When using a dual-ring architecture, users must complete configuration for both Ring 1 and Ring 2. The status of both rings will appear under Current Status. "Current Status" Items Now Active This shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, Turbo Chain, RSTP, or none. Ring 1/2—Status This shows Healthy if the ring is operating normally, and shows Break if the ring’s backup link is active.
PT-G7509 User’s Manual Featured Functions Enable Ring 2* Setting Enabled Disabled Description Enables Ring 2. This disables Ring 2. Factory Default Not checked *Both Ring 1 and Ring 2 must be enabled when using the dual-ring architecture. Set as Master Setting Enabled Disabled Description The PT-G7509 is manually selected as the master. The Turbo Ring or Turbo Ring V2 protocol will automatically select the master.
PT-G7509 User’s Manual Featured Functions The Turbo Chain Concept Moxa’s Turbo Chain is an advanced software technology that gives network administrators the flexibility to construct any type of redundant network topology. When using a Turbo Chain, you first connect the Ethernet switches in a chain and then simply link the two ends of the chain to an Ethernet network, as illustrated in the following figure. Turbo Chain can be used on industrial networks that have a complex topology.
PT-G7509 User’s Manual Featured Functions Configuring “Turbo Chain” Head Switch Configuration Member Switch Configuration 3-35
PT-G7509 User’s Manual Featured Functions Tail Switch Configuration Explanation of “Current Status” Items Now Active Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP, Turbo Chain or None. The “Ports Status” indicators show Forwarding for normal transmission, Blocked if this port is connected to the Tail port as a backup path and the path is blocked, and Link down if there is no connection.
PT-G7509 User’s Manual Featured Functions Head Role Setting Description Factory Default Head Port Select any port of the PT to be the head port. Member Port Select any port of the PT to be the member port G9 port.
PT-G7509 User’s Manual Featured Functions What is STP? STP (802.1D) is a bridge-based system that is used to implement parallel paths for network traffic. STP uses a loop-detection process to: y y Locate and then disable less efficient paths (i.e., paths that have a lower bandwidth) Enable one of the less efficient paths if the most efficient path fails The figure below shows a network made up of three LANs separated by three bridges.
PT-G7509 User’s Manual Featured Functions What happens if a link failure is detected? As shown in next figure, the STP process reconfigures the network so that traffic from LAN segment 2 flows through Bridge B. STP will determine which path between each bridged segment is most efficient, and then assign a specific reference point on the network. When the most efficient path has been identified, the other paths are blocked.
PT-G7509 User’s Manual Featured Functions STP Calculation The first step of the STP process is to perform calculations. During this stage, each bridge on the network transmits BPDUs. The following items will then be calculated: y y y y The bridge that will act as the Root Bridge. The Root Bridge is the central reference point from which the network is configured. The Root Path Costs for each bridge. This is the cost of the paths from each bridge to the Root Bridge.
PT-G7509 User’s Manual Featured Functions STP Example The LAN shown below has three segments, with adjacent segments connected using two possible links. The various STP factors, such as Cost, Root Port, Designated Bridge Port, and Blocked Port are shown in the figure. y y y y y y Bridge A has been selected as the Root Bridge, since it was determined to have the lowest Bridge Identifier on the network. Since Bridge A is the Root Bridge, it is also the Designated Bridge for LAN segment 1.
PT-G7509 User’s Manual Featured Functions Using STP on a Network with Multiple VLANs IEEE Std 802.1D, 1998 Edition, does not take into account VLANs when calculating STP information—the calculations only depend on the physical connections. Consequently, some network configurations will result in VLANs being subdivided into a number of isolated sections by the STP system.
PT-G7509 User’s Manual Featured Functions Configuring STP/RSTP The following figures indicate which Spanning Tree Protocol parameters can be configured. A more detailed explanation of each parameter is given below the figure. At the top of this page, the user can check the Current Status of this function. For RSTP, you will see: Now Active: This field shows which communication protocol is being used—Turbo Ring, RSTP, or neither. Root/Not Root This field appears only for RSTP mode.
PT-G7509 User’s Manual Featured Functions Forwarding Delay Setting Numerical value input by user Description Specifies the amount of time this device will wait before checking to see if it should change to a different state. Factory Default 15 (sec.) Hello Time (sec.) Setting Numerical value input by user Description Factory Default Specifies the time interval between “hello” 2 messages broadcast by the root of the Spanning Tree topology.
PT-G7509 User’s Manual Featured Functions Configuration Limits of RSTP/STP The Spanning Tree Algorithm places limits on three of the configuration items: [Eq. 1]: 1 sec ≦ Hello Time ≦ 2 sec [Eq. 2]: 6 sec ≦ Max. Age ≦ 40 sec [Eq. 3]: 4 sec ≦ Forwarding Delay ≦ 30 sec These three variables are further restricted by the following two inequalities: [Eq. 4]: 2 * (Hello Time + 1 sec) ≦ Max.
PT-G7509 User’s Manual Featured Functions How Traffic Prioritization Works Traffic prioritization uses the four traffic queues that are present in your PT-G7509 to ensure that high priority traffic is forwarded on a different queue from lower priority traffic. This is what provides Quality of Service (QoS) to your network. The PT-G7509 traffic prioritization depends on two industry-standard methods: y y IEEE 802.1D—a layer 2 marking scheme. Differentiated Services (DiffServ)—a layer 3 marking scheme.
PT-G7509 User’s Manual Featured Functions Advantages of DiffServ over IEEE 802.1D are: y y y y Configure how you want your switch to treat selected applications and types of traffic by assigning various grades of network service to them. No extra tags are required in the packet. DSCP uses the IP header of a packet and therefore priority is preserved across the Internet.
PT-G7509 User’s Manual Featured Functions Configuring Traffic Prioritization Quality of Service (QoS) provides a traffic prioritization capability to ensure that important data is delivered consistently and predictably. The PT-G7509 can inspect IEEE 802.1p/1Q layer 2 CoS tags, and even layer 3 TOS information, to provide a consistent classification of the entire network. The PT-G7509’ QoS capability improves your industrial network’s performance and determinism for mission critical applications.
PT-G7509 User’s Manual Featured Functions Inspect TOS Setting Enable/Disable Description Factory Default Enables or disables the PT-G7509 to inspect the Type of Enable Service (TOS) bits in IPV4 frame to determine the priority of each frame. Inspect COS Setting Enable/Disable Description Enables or disables the PT-G7509 to inspect the 802.1p COS tag in the MAC frame to determine the priority of each frame.
PT-G7509 User’s Manual Featured Functions TOS/DiffServ Mapping Setting Low/Normal/ Medium/High Description Factory Default This maps different TOS values to 4 different egress 1 to 16: Low queues. 17 to 32: Normal 33 to 48: Medium 49 to 64: High Using Virtual LAN Setting up Virtual LANs (VLANs) on your PT-G7509 increases the efficiency of your network by dividing the LAN into logical segments, as opposed to physical segments. In general, VLANs are easier to manage.
PT-G7509 User’s Manual Featured Functions The Virtual LAN (VLAN) Concept What is a VLAN? A VLAN is a group of devices that can be located anywhere on a network, but which communicate as if they are on the same physical segment. With VLANs, you can segment your network without being restricted by physical connections—a limitation of traditional network design.
PT-G7509 User’s Manual Featured Functions VLANs and the PowerTrans Your PT-G7509 provides support for VLANs using IEEE Std 802.1Q-1998. This standard allows traffic from multiple VLANs to be carried across one physical link. The IEEE Std 802.1Q-1998 standard allows each port on your PT-G7509 to be placed as follows: y y In a single VLAN defined on the PT-G7509 In several VLANs simultaneously using 802.1Q tagging The standard requires that you define the 802.
PT-G7509 User’s Manual Featured Functions The PT-G7509 supports two types of VLAN port settings: y y Access Port: The port connects to a single device that is not tagged. The user must define the default port PVID that assigns which VLAN the device belongs to. Once the ingress packet of this Access Port egresses to another Trunk Port (the port nePT all packets to carry tag information), the PT-G7509 will insert this PVID into this packet to help the next 802.1Q VLAN switch recognize it.
PT-G7509 User’s Manual Featured Functions After proper configuration: y Packets from Device A will travel through Trunk Port 3 with tagged VID 5. Switch B will recognize its VLAN, pass it to port 6, and then remove tags received successfully by Device G, and vice versa. y Packets from Devices B and C will travel through Trunk Port 3 with tagged VID 2. Switch B recognizes its VLAN, passes it to port 4, and then removes tags received successfully by Device F, and vice versa.
PT-G7509 User’s Manual Featured Functions VLAN Mode Setting 802.1Q VLAN Port-based VLAN 802.1Q VLAN (Unaware) Description Set VLAN mode to 802.1Q VLAN Set VLAN mode to Port-based VLAN Set VLAN mode to Unaware Factory Default 802.1Q VLAN Management VLAN ID Setting VLAN ID from 1 to 4094 Description Assigns the VLAN ID of this PT-G7509. Factory Default 1 Port Type Setting Access Trunk Description This port type is used to connect single devices without tags.
PT-G7509 User’s Manual Featured Functions To configure the PT-G7509’s port-based VLAN, use the VLAN settings page to configure the ports. VLAN Mode Setting Description 802.1Q VLAN Set VLAN mode to 802.1Q VLAN Port-based VLAN Set VLAN mode to Port-based VLAN 802.1Q VLAN Set VLAN mode to Unaware (Unaware) Factory Default 802.1Q VLAN Port Setting Enable/Disable Description Set port to specific VLAN Group.
PT-G7509 User’s Manual Featured Functions For certain Power Substation scenarios, some applications may require priority-tagged frames to be received by IEDs. To fulfill these requirements Moxa PT-G7509 Series Ethernet switches allow VLAN Unaware Mode operation. Frames ingress a VLAN-unaware switch and are not associated with any VLAN. Frames egress a VLAN-unaware switch and are sent out unmodified. PVID=2 VID=0 VID=0 IED IED VLAN Table In 802.
PT-G7509 User’s Manual Featured Functions Using Multicast Filtering Multicast filtering improves the performance of networks that carry multicast traffic. This section explains multicasts, multicast filtering, and how multicast filtering can be implemented on your PT-G7509. The Concept of Multicast Filtering What is an IP Multicast? A multicast is a packet sent by one host to multiple hosts. Only those hosts that belong to a specific multicast group will receive the multicast.
PT-G7509 User’s Manual Featured Functions Multicast Filtering Multicast filtering ensures that only end-stations that have joined certain groups receive multicast traffic. With multicast filtering, network devices only forward multicast traffic to the ports that are connected to registered end-stations. The following two figures illustrate how a network behaves without multicast filtering, and with multicast filtering.
PT-G7509 User’s Manual Featured Functions Multicast Filtering and Moxa PowerTrans Switch The PT-G7509 has three ways to achieve multicast filtering: IGMP (Internet Group Management Protocol) Snooping, GMRP (GARP Multicast Registration Protocol), and adding a static multicast MAC manually to filter multicast traffic automatically. IGMP (Internet Group Management Protocol) Snooping Mode Snooping Mode allows your switch to forward multicast packets only to the appropriate ports.
PT-G7509 User’s Manual Featured Functions GMRP (GARP Multicast Registration Protocol) The PT-G7509 supports IEEE 802.1D-1998 GMRP (GARP Multicast Registration Protocol), which differs from IGMP (Internet Group Management Protocol). GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP provides a mechanism that allows bridges and end stations to register or de-register Group membership information dynamically.
PT-G7509 User’s Manual Featured Functions IGMP Snooping Enhanced Mode Setting Enable Disable Description IGMP Multicast packets will be forwarded to: y Auto-Learned Multicast Querier Ports y Member Ports IGMP Multicast packets will be forwarded to: y Auto-Learned Multicast Querier Ports y Static Multicast Querier Ports y Querier Connected Ports y Member Ports Factory Default Enable Query Interval Setting Numerical value input by user Description This sets the query interval of the Querier function gl
PT-G7509 User’s Manual Featured Functions IGMP Table The PT-G7509 displays the current active IGMP groups that were detected. The information includes VID, Auto-learned Multicast Router Port, Static Multicast Router Port, Querier Connected Port, and the IP and MAC addresses of active IGMP groups. Add Static Multicast MAC If required, the PT-G7509 also supports adding multicast groups manually.
PT-G7509 User’s Manual Featured Functions Configuring GMRP GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP provides a mechanism that allows bridges and end stations to register or un-register Group membership information dynamically.
PT-G7509 User’s Manual Featured Functions Using Bandwidth Management In general, one host should not be allowed to occupy unlimited bandwidth, particularly when the device malfunctions. The PT-G7509 can be configured to a different ingress rate for all packets, giving administrators full control of their limited bandwidth to prevent undesirable effects caused by unpredictable faults.
PT-G7509 User’s Manual Featured Functions The IEEE 802.1X Concept Three components are used to create an authentication mechanism based on 802.1X standards: Client/Supplicant, Authentication Server, and Authenticator. Supplicant: The end station that requests access to the LAN and switch services and responds to the requests from the switch. Authentication server: The server that performs the actual authentication of the supplicant.
PT-G7509 User’s Manual Featured Functions Configuring IEEE 802.1X Database Option Setting Local (Max. 32 users) Radius Radius, Local Description Factory Default Select this option when setting the Local User Database Local as the authentication database. Select this option to set an external RADIUS server as Local the authentication database. The authentication mechanism is EAP-MD5. Select this option to make using an external RADIUS Local server as the authentication database the second priority.
PT-G7509 User’s Manual Featured Functions Re-Auth Setting Enable/Disable Description Select to require re-authentication of the client after a preset time period of no activity has elapsed. Factory Default Disable Re-Auth Period Setting Description Numerical Specify how frequently the end stations need to reenter (60 to 65535 sec.) usernames and passwords in order to stay connected. Factory Default 3600 802.1X Setting Enable/Disable Description Click the checkbox under the 802.
PT-G7509 User’s Manual Featured Functions Local User Database Setup When setting the Local User Database as the authentication database, set the database first. Local User Database Setup Setting User Name (Max. 30 characters) Password (Max. 16 characters) Description (Max. 30 characters) NOTE Description User Name for Local User Database Factory Default None Password for Local User Database None Description for Local User Database None The user name for the Local User Database is case-insensitive.
PT-G7509 User’s Manual Featured Functions Port Access Control Table The port status will show authorized or unauthorized. Using Auto Warning Since industrial Ethernet devices are often located at the endpoints of a system, these devices will not always know what is happening elsewhere on the network. This means that an industrial Ethernet switch that connects to these devices must provide system maintainers with real-time alarm messages.
PT-G7509 User’s Manual Featured Functions Event Type Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of a specific port. System Events Warning e-mail is sent when… Switch Cold Start Power is cut off and then reconnected. Switch Warm Start the PT-G7509 is rebooted, such as when network parameters are changed (IP address, subnet mask, etc.).
PT-G7509 User’s Manual Featured Functions Port Events Link-ON Link-OFF Traffic-Overload Warning e-mail is sent when… The port is connected to another device. The port is disconnected (e.g., the cable is pulled out, or the opposing device shuts down). The port’s traffic surpasses the Traffic-Threshold for that port (provided this item is Enabled). Traffic-Threshold (%) Enter a nonzero number if the port’s Traffic-Overload item is Enabled. Traffic-Duration (sec.
PT-G7509 User’s Manual Featured Functions Email Setup Mail Server IP/Name Setting IP address Description The IP Address of your email server. Factory Default None Account Name Setting Max. 45 Charters Description Your email account.
PT-G7509 User’s Manual Featured Functions Send Test Email After finishing with the email settings, you should first click Activate to activate those settings, and then press the Send Test Email button to verify that the settings are correct. NOTE Auto warning e-mail messages will be sent through an authentication protected SMTP server that supports the CRAM-MD5, LOGIN, and PAIN methods of SASL (Simple Authentication and Security Layer) authentication mechanism.
PT-G7509 User’s Manual Featured Functions System Events Warning e-mail is sent when… Switch Cold Start Switch Warm Start Power is cut off and then reconnected. The PT- G7509 is rebooted, such as when network parameters are changed (IP address, subnet mask, etc.). Power Transition (OnÆOff) The PT- G7509 is powered down. Power Transition (OffÆOn) Configuration Change Activated The PT- G7509 is powered up. Any configuration item has been changed.
PT-G7509 User’s Manual Featured Functions Override relay alarm settings Click the checkbox to override the relay warning setting temporarily. Releasing the relay output will allow administrators to fix any problems with the warning condition. Warning List Use this table to see if any relay alarms have been issued.
PT-G7509 User’s Manual Featured Functions Using Set Device IP To reduce the effort required to set up IP addresses, the PT-G7509 comes equipped with DHCP/BootP server and RARP protocol to set up IP addresses of Ethernet-enabled devices automatically. When enabled, the Set device IP function allows the PT-G7509 to assign specific IP addresses automatically to connected devices that are equipped with DHCP Client or RARP protocol.
PT-G7509 User’s Manual Featured Functions Configuring Set Device IP Desired IP Address Setting IP Address Description Set the desired IP of connected devices. Factory Default None Configuring DHCP Relay Agent The DHCP Relay Agent makes it possible for DHCP broadcast messages to be sent over routers. The DHCP Relay Agent enables DHCP clients to obtain IP addresses from a DHCP server on a remote subnet, or those that are not located on the local subnet.
PT-G7509 User’s Manual Featured Functions example, 01–00–0F–03 is the “Circuit ID” of port number 3 with port VLAN ID 15. The “Remote ID” is to identify the relay agent itself. It can be one of the following types: 1. The IP address of the relay agent. 2. The MAC address of the relay agent. 3. The combination of IP address and MAC address of the relay agent. 4. A user-defined string.
PT-G7509 User’s Manual Featured Functions 4th Server Setting IP address for the 4th DHCP server Description Assigns the IP address of the 4th DHCP server that the switch tries to access. Factory Default None DHCP Option 82 Enable Option82 Setting Description Enable or Disable Enable or disable DHCP Option 82 function. Factory Default Disable Type Setting IP MAC Client-ID Other Description Use the switch’s IP address as the remote ID sub-option.
PT-G7509 User’s Manual Featured Functions Using Diagnosis The PT-G7509 provides two important tools for administrators to diagnose network systems. Mirror Port The Mirror port function can be used to monitor data being transmitted through a specific port. This is done by setting up another port (the mirror port) to receive the same data being transmitted from, or both to and from, the port under observation.
PT-G7509 User’s Manual Featured Functions Ping The Ping function uses the ping command to give users a simple but powerful tool for troubleshooting network problems. The function’s most unique feature is that even though the ping command is entered from the user’s PC keyboard, the actual ping command originates from the PT-G7509 itself. In this way, the user can essentially sit on top of the PT-G7509 and send ping commands out through its ports.
PT-G7509 User’s Manual Featured Functions LLDP Settings Enable LLDP Setting Description Enable or Disable Enable or disable LLDP function. Factory Default Enable Value Setting 5 to 32768 Description Transmit interval of LLDP messages, in seconds. Factory Default 30 (seconds) LLDP Setting Enable/Disable Description Enable or disable LLDP function Factory Default Enable Message Transmit Interval Setting 5 to 32768 Description Transmit interval of LLDP messages, in seconds.
PT-G7509 User’s Manual Featured Functions Using Monitor You can monitor statistics in real time from the PT-G7509’s web console and serial console. Monitor by Switch Access the Monitor by selecting System from the left selection bar. Monitor by System allows the user to view a graph that shows the combined data transmission activity of all of the PT-G7509’s 18 ports.
PT-G7509 User’s Manual Featured Functions Monitor by Port Access the Monitor by Port function by selecting ALL Gigabit Ports from the left pull-down list. The Gigabit port options are identical to the Monitor by System function discussed above, in that users can view graphs that show All Packets, TX Packets, RX Packets, or Error Packets activity, but in this case, only for an individual port.
PT-G7509 User’s Manual Featured Functions The table will display the following information: MAC Type Port This field shows the MAC address This field shows the type of this MAC address This field shows the port that this MAC address belongs to Using Event Log Bootup Date Time System Startup Time Events NOTE This field shows how many times the PT-G7509 has been rebooted or cold started. The date is updated based on how the current date is set in the Basic Setting page.
PT-G7509 User’s Manual Featured Functions Using Syslog This function provides the event logs for the syslog server. The function supports 3 configurable syslog servers and syslog server UDP port numbers. When an event occurs, the event will be sent as a syslog UDP packet to the specified syslog servers. Syslog Server 1 Setting IP Address Port Destination (1 to 65535) Description Enter the IP address of 1st Syslog server used by your network. Enter the UDP port of 1st Syslog server.
PT-G7509 User’s Manual NOTE Featured Functions The following events will be recorded into the PT-G7509’s Event Log table, and will then be sent to the specified Syslog Server: y Cold start y Warm start y Configuration change activated y Power 1/2 transition (Off Æ On), Power 1/2 transition (On Æ Off) y Authentication fail y Topology changed y Master setting is mismatched y Port traffic overload y dot1x Auth Fail y Port link off / on 3-88
A Appendix A MIB Groups The PT-G7509 comes with built-in SNMP (Simple Network Management Protocol) agent software that supports cold/warm start trap, line up/down trap, and RFC 1213 MIB-II. The standard MIB groups that the PT-G7509 supports are as follows: MIB II.1 – System Group sysORTable MIB II.2 – Interfaces Group ifTable MIB II.4 – IP Group ipAddrTable ipNetToMediaTable IpGroup IpBasicStatsGroup IpStatsGroup MIB II.5 – ICMP Group IcmpGroup IcmpInputStatus IcmpOutputStats MIB II.
PT-G7509 User’s Manual MIB Groups MIB II.10 – Transmission Group dot3 dot3StatsTable MIB II.11 – SNMP Group SnmpBasicGroup SnmpInputStats SnmpOutputStats MIB II.
PT-G7509 User’s Manual MIB Groups The PT-G7509 also provides a private MIB file, located in the file Moxa-PTG7509-MIB.my on the PT-G7509 utility CD-ROM.
B Appendix B Technology Standards Flow control Protocols: MIB: Switch Properties Priority Queues: Max. Number of Available VLANs: VLAN ID Range: IGMP Groups: Interface Fiber Ports RJ45 Ports Console: System LED Indicators: Module LED Indicators: Alarm Contact: Power Input Voltage Input Current Specifications IEEE 802.3 for 10BaseT, IEEE 802.3u for 100BaseT(X) and 100BaseFX, IEEE 802.3ab for 1000BaseT(X), IEEE 802.3z for 1000BaseSX/LX/LHX/ZX, IEEE 802.3x for Flow Control, IEEE 802.
PT-G7509 User’s Manual Connection Overload Current Protection Reverse Polarity Protection Mechanical Casing Dimensions (W x H x D) Installation Environmental Operating Temp. Storage Temp. Ambient Relative Humidity Warranty Specifications Max. 0.56A @48VC, Max 0.27/0.16A @ 110/220VDC Max 0.64/0.37A @ 110/220VAC 10-pin terminal block Present Present IP30 protection 440 x 44 x 254 mm (17.32 x 1.73 x 10.00 in.) 19-inch rack mounting -40 to 85°C (-40 to 185°F) Cold start of min.
C Appendix C Modbus/TCP Map Modbus Information Read Only Registers (Support Function Code 4) Address Data Type 0x0000 0x0001 0x0002 0x0010 1 word 1 word 1 word 20 word 0x0030 20 word 0x0050 0x0051 1 word 2 word 0x0053 2 word 1 Word = 2Bytes Description System Information Vendor ID = 0x1393 Unit ID (Ethernet = 1) Product Code = 0x0013 Vendor Name = “Moxa” Word 0 Hi byte = ‘M’ Word 0 Lo byte = ‘o’ Word 1 Hi byte = ‘x’ Word 1 Lo byte = ‘a’ Word 2 Hi byte = ‘\0’ Word 2 Lo byte = ‘\0’ Product Name
PT-G7509 User’s Manual Modbus/TCP Map 0x0055 3 word 0x0058 1 word 0x0059 1 word 0x005A 1 word 0x0080 1 word 0x0081 1 word 0x0082 1 word 0x0083 1 word 0x1000~0x1011 1 word 0x1100~0x1111 1 word 0x1200~0x1211 1 word 0x1300~0x1311 1 word Ethernet MAC Address Ex: MAC = 00-01-02-03-04-05 Word 0 Hi byte = 0x00 Word 0 Lo byte = 0x01 Word 1 Hi byte = 0x02 Word 1 Lo byte = 0x03 Word 2 Hi byte = 0x04 Word 2 Lo byte = 0x05 Power 1 0x0000:Off 0x0001:On Power 2 0x0000:Off 0x0001:On Fault LED Sta
PT-G7509 User’s Manual Modbus/TCP Map 0x1400~0x1413(Port 1) 20 word 0x1414~0x1427(Port 2) 0x2000~0x2023 2 word 0x2100~0x2123 2 word 0x2200~0x2223 2 word 0x2300~0x2323 2 word 0x3000 1 word 0x3100 1 word 0x3200~0x3211 1 word 0x3300 1 word Port 1~18 Description Port Description = "100TX,RJ45." Word 0 Hi byte = ‘1’ Word 0 Lo byte = ‘0’ Word 1 Hi byte = ‘0’ Word 1 Lo byte = ‘T’ … Word 4 Hi byte = ‘4’ Word 4 Lo byte = ‘5’ Word 5 Hi byte = ‘.
PT-G7509 User’s Manual Modbus/TCP Map 0x3301 1 word 0x3302 1 word 0x3303 1 word 0x3304 1 word 0x3305 1 word 0x3500 1 word 0x3501 1 word TR 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR Coupling 0x0000:Off 0x0001:On 0xFFFF:Turbo Ring Not Enable TR Coupling Port status 0x0000:Port Disabled
PT-G7509 User’s Manual Modbus/TCP Map 0x3502 1 word 0x3600 1 word 0x3601 1 word 0x3602 1 word 0x3603 1 word 0x3680 1 word 0x3681 1 word 0x3682 1 word TR2 Coupling Port Backup status (Only using in Dual Homing) 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turb
PT-G7509 User’s Manual 0x3683 Modbus/TCP Map 1 word TR2 Ring 2 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 2 Not Enable Memory mapping from address 0x0000 ~ 0x3FFF.
PT-G7509 User’s Manual Modbus/TCP Map 0x0055 3 word Ethernet MAC Address Ex: MAC = 00-01-02-03-04-05 Word 0 Hi byte = 0x00 Word 0 Lo byte = 0x01 Word 1 Hi byte = 0x02 Word 1 Lo byte = 0x03 Word 2 Hi byte = 0x04 Word 2 Lo byte = 0x05 0x0058 1 word Power 1 0x0000:Off 0x0001:On 0x0059 1 word Power 2 0x0000:Off 0x0001:On 0x005A 1 word Fault LED Status 0x0000:No 0x0001:Yes 0x0080 1 word DI1 0x0000:Off 0x0001:On 0x0081 1 word DI2 0x0000:Off 0x0001:On 0x0082 1 word DO1 0x0000:Off 0x0001:On 0
PT-G7509 User’s Manual 0x1100~0x1111 Modbus/TCP Map 1 word Port 1~18 Speed 0x0000:10M-Half 0x0001:10M-Full 0x0002:100M-Half 0x0003:100M-Full 0x0004:1G-Half 0x0005:1G- Full 0xFFFF:No port 0x1200~0x1211 1 word Port 1~18 Flow Ctrl 0x0000:Off 0x0001:On 0xFFFF:No port 0x1300~0x1311 1 word Port 1~18 MDI/MDIX 0x0000:MDI 0x0001:MDIX 0xFFFF:No port 0x1400~0x1413(Port 1) 20 word 0x1414~0x1427(Port 2) Port 1~18 Description Port Description = “100TX,RJ45.
PT-G7509 User’s Manual Modbus/TCP Map 0x3000 1 word Redundancy Protocol 0x0000:None 0x0001:RSTP 0x0002:Turbo Ring 0x0003:Turbo Ring V2 0x3100 1 word RSTP Root 0x0000:Not Root 0x0001:Root 0xFFFF:RSTP Not Enable 0x3200~0x3211 1 word RSTP Port 1~18 Status 0x0000:Port Disabled 0x0001:Not RSTP Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:RSTP Not Enable 0x3300 1 word TR Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turbo Ring Not Enable 0x3301 1 word TR 1st Port
PT-G7509 User’s Manual 0x3305 Modbus/TCP Map 1 word TR Coupling Control Port status 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0005:Forwarding 0x0006:Inactive 0x0007:Active 0xFFFF:Turbo Ring Not Enable 0x3500 1 word TR2 Coupling Mode 0x0000:None 0x0001:Dual Homing 0x0002:Coupling Backup 0x0003:Coupling Primary 0xFFFF:Turbo Ring V2 Not Enable 0x3501 1 word TR2 Coupling Port Primary status (Using in Dual Homing, Coupling Backup, Coupling Primary) 0x0000:Port Disabl
PT-G7509 User’s Manual Modbus/TCP Map 0x3602 1 word TR2 Ring 1 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not Enable 0x3603 1 word TR2 Ring 1 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not Enable 0x3680 1 word TR2 Ring 2 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Ring 2
PT-G7509 User’s Manual Modbus/TCP Map Modbus Information Read Only Registers (Support Function Code 4) Address Data Type 1 Word = 2Bytes Description System Information 0x0000 1 word Vendor ID = 0x1393 0x0001 1 word Unit ID (Ethernet = 1) 0x0002 1 word Product Code = 0x0016 0x0010 20 word Vendor Name = “Moxa” Word 0 Hi byte = ‘M’ Word 0 Lo byte = ‘o’ Word 1 Hi byte = ‘x’ Word 1 Lo byte = ‘a’ Word 2 Hi byte = ‘\0’ Word 2 Lo byte = ‘\0’ 0x0030 20 word Product Name = “PT-G7509” Word 0 Hi byte
PT-G7509 User’s Manual Modbus/TCP Map 0x0058 1 word Power 1 0x0000:Off 0x0001:On 0x0059 1 word Power 2 0x0000:Off 0x0001:On 0x005A 1 word Fault LED Status 0x0000:No 0x0001:Yes 0x0080 1 word DI1 0x0000:Off 0x0001:On 0x0081 1 word DI2 0x0000:Off 0x0001:On 0x0082 1 word DO1 0x0000:Off 0x0001:On 0x0083 1 word DO2 0x0000:Off 0x0001:On Port Information 0x1000~0x1011 1 word Port 1~18 Status 0x0000:Link down 0x0001:Link up 0x0002:Disable 0xFFFF:No port 0x1100~0x1111 1 word Port 1~18 Spee
PT-G7509 User’s Manual 0x1300~0x1311 Modbus/TCP Map 1 word 0x1400~0x1413(Port 1) 20 word 0x1414~0x1427(Port 2) Port 1~18 MDI/MDIX 0x0000:MDI 0x0001:MDIX 0xFFFF:No port Port 1~18 Description Port Description = "100TX,RJ45." Word 0 Hi byte = ‘1’ Word 0 Lo byte = ‘0’ Word 1 Hi byte = ‘0’ Word 1 Lo byte = ‘T’ … Word 4 Hi byte = ‘4’ Word 4 Lo byte = ‘5’ Word 5 Hi byte = ‘.
PT-G7509 User’s Manual Modbus/TCP Map 0x3200~0x3211 1 word RSTP Port 1~18 Status 0x0000:Port Disabled 0x0001:Not RSTP Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:RSTP Not Enable 0x3300 1 word TR Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turbo Ring Not Enable 0x3301 1 word TR 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0x3302 1 word TR 2nd Port status 0x0000:Port Disabled 0x0001
PT-G7509 User’s Manual Modbus/TCP Map 0x3500 1 word TR2 Coupling Mode 0x0000:None 0x0001:Dual Homing 0x0002:Coupling Backup 0x0003:Coupling Primary 0xFFFF:Turbo Ring V2 Not Enable 0x3501 1 word TR2 Coupling Port Primary status (Using in Dual Homing, Coupling Backup, Coupling Primary) 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Not Enable 0x3502 1 word TR2 Coupling Port Backup status (Only using in Dual Homing)
PT-G7509 User’s Manual Modbus/TCP Map 0x3680 1 word TR2 Ring 2 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3681 1 word TR2 Ring 2 Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3682 1 word TR2 Ring 2 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3683 1 word TR2 Ring 2 2nd Port status 0x0000:Port Disabled 0x0001:N
PT-G7509 User’s Manual Modbus/TCP Map Modbus information Read Only Registers (Support Function Code 4) Address Data Type 1 Word = 2Bytes Description System Information 0x0000 1 word Vendor ID = 0x1393 0x0001 1 word Unit ID (Ethernet = 1) 0x0002 1 word Product Code = 0x0017 0x0010 20 word Vendor Name = “Moxa” Word 0 Hi byte = ‘M’ Word 0 Lo byte = ‘o’ Word 1 Hi byte = ‘x’ Word 1 Lo byte = ‘a’ Word 2 Hi byte = ‘\0’ Word 2 Lo byte = ‘\0’ 0x0030 20 word Product Name = “PT-G7509” Word 0 Hi byte
PT-G7509 User’s Manual Modbus/TCP Map 0x0058 1 word Power 1 0x0000:Off 0x0001:On 0x0059 1 word Power 2 0x0000:Off 0x0001:On 0x005A 1 word Fault LED Status 0x0000:No 0x0001:Yes 0x0080 1 word DI1 0x0000:Off 0x0001:On 0x0081 1 word DI2 0x0000:Off 0x0001:On 0x0082 1 word DO1 0x0000:Off 0x0001:On 0x0083 1 word DO2 0x0000:Off 0x0001:On Port Information 0x1000~0x1011 1 word Port 1~18 Status 0x0000:Link down 0x0001:Link up 0x0002:Disable 0xFFFF:No port 0x1100~0x1111 1 word Port 1~18 Spee
PT-G7509 User’s Manual 0x1300~0x1311 Modbus/TCP Map 1 word 0x1400~0x1413(Port 1) 20 word 0x1414~0x1427(Port 2) Port 1~18 MDI/MDIX 0x0000:MDI 0x0001:MDIX 0xFFFF:No port Port 1~18 Description Port Description = “100TX,RJ45.” Word 0 Hi byte = ‘1’ Word 0 Lo byte = ‘0’ Word 1 Hi byte = ‘0’ Word 1 Lo byte = ‘T’ … Word 4 Hi byte = ‘4’ Word 4 Lo byte = ‘5’ Word 5 Hi byte = ‘.
PT-G7509 User’s Manual Modbus/TCP Map 0x3200~0x3211 1 word RSTP Port 1~18 Status 0x0000:Port Disabled 0x0001:Not RSTP Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:RSTP Not Enable 0x3300 1 word TR Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turbo Ring Not Enable 0x3301 1 word TR 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0x3302 1 word TR 2nd Port status 0x0000:Port Disabled 0x0001
PT-G7509 User’s Manual Modbus/TCP Map 0x3500 1 word TR2 Coupling Mode 0x0000:None 0x0001:Dual Homing 0x0002:Coupling Backup 0x0003:Coupling Primary 0xFFFF:Turbo Ring V2 Not Enable 0x3501 1 word TR2 Coupling Port Primary status (Using in Dual Homing, Coupling Backup, Coupling Primary) 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Not Enable 0x3502 1 word TR2 Coupling Port Backup status (Only using in Dual Homing)
PT-G7509 User’s Manual Modbus/TCP Map 0x3680 1 word TR2 Ring 2 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3681 1 word TR2 Ring 2 Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3682 1 word TR2 Ring 2 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 2 Not Enable 0x3683 1 word TR2 Ring 2 2nd Port status 0x0000:Port Disabled 0x0001:N
