Specifications

4-14
www.moxa.com
[e-mail]
MGate™ EIP3000 Series
4
Industrial Ethernet Gateways
Industrial Ethernet Gateways >
Each MGate™ EIP3000 gateway supports virtual serial ports for the
remote PC. You can connect to the MGate™ EIP3000 through the
COM port by using Moxa’s Real COM driver, with the actual physical
When using termination resistors to prevent serial signal reflection,
it is important to set the pull high/low resistors correctly so that the
electrical signal is not corrupted. Since no set of resistor values is
Complex device networks that incorporate high amperage devices
could be subject to electrical signal distortion from electrical
connection over the Ethernet. The gateway supports up to 4 virtual
COM port connections and offers greater flexibility when designing
redundant control systems.
discharges, magnetic noise, or common mode transients. MGate™
series products solve this problem by using built-in optical isolation.
universally compatible with all environments, the EIP3000 has DIP
switches on the bottom panel for setting the termination and pull high/
low resistor values.
The serial redirector function allows the commands of a serial master
(command initiator) to be redirected to the serial slave (command
executor) on another port. In addition, a serial master can operate
simultaneously with EtherNet/IP masters without changing the DF1
architecture or software. With the serial redirector function, MGate™
EIP3000 gateways can establish redundant control of legacy slave
devices that were originally designed to be controlled by a single serial
master.
Built-in Isolation
Specifications
ProCOM Implements Control via COM Port Mapping
Pull high/low Resistors and Terminator Selection
Serial Redirector Function Maintains Original Master/Slave Connections
Ethernet Interface
Protocol: CIP (PCCC) on EtherNet/IP
Number of Ports:
EIP3170/3170I: 2 (1 IP, Ethernet cascade)
EIP3270/3270I: 2 (2 IPs)
Speed: 10/100 Mbps, Auto MDI/MDIX
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 kV (built-in)
Serial Interface
Protocol: DF1 Full-duplex
Number of Ports:
EIP3170/3170I: 1
EIP3270/3270I: 2
Serial Standards: RS-232/422, software selectable
Connectors:
EIP3170/3170I: DB9 male for RS-232, terminal block for RS-422
EIP3270/3270I: DB9 male x 2
ESD Protection: 15 kV for all signals
Serial Communication Parameters
Data Bits: 8
Stop Bits: 1, 2
Parity: None, Even, Odd
Flow Control: RTS/CTS, DTR/DSR (RS-232 only)
Baudrate: 1200 bps to 921.6 kbps
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
Software
Utility: MGate Manager for Windows 2000/XP/2003/Vista/Server
2008/7/8 (x86/x64), Windows Server 2008 R2/2012 (x64)
Conguration Options: Serial Console, Telnet Console, Windows Utility
Support: Smart Routing, Serial Redirection, ProCOM, MXview, SNMP
v1 (read only)
Physical Characteristics
Housing: Plastic
Weight:
MGate EIP3170: 360 g
MGate EIP3270: 380 g
Dimensions:
Without ears: 29 x 89.2 x 118.5 mm (1.14 x 3.51 x 4.67 in)
With ears extended: 29 x 89.2 x 124.5 mm (1.14 x 3.51 x 4.90 in)
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Altitude: Up to 2000 m (795 hPa), higher altitudes on demand
Note: Please contact Moxa if you require products guaranteed to function
properly at higher altitudes.
Power Requirements
Input Voltage: 12 to 48 VDC
Power Connector: Terminal block
Power Consumption:
MGate M3170: 435 mA (max.)
MGate M3170I: 555 mA (max.)
MGate M3270: 435 mA (max.)
MGate M3270I: 510 mA (max.)
Standards and Certifications
Safety: UL 508, EN 60950-1
Hazardous Location:
UL/cUL Class 1 Division 2 Groups A/B/C/D,
ATEX Zone 2 Ex nA IIC T3 Gc, IECEx (-IEX model only)
EMC: CE, FCC
EMI: EN 55022 Class A, FCC Part 15 Subpart B Class A
EMS:
EN 55024,
EN 61000-4-2 (ESD) Level 3,
EN 61000-4-3 (RS) Level 3,
EN 61000-4-4 (EFT) Level 4,
EN 61000-4-5 (Surge) Level 3,
EN 61000-4-6 (CS) Level 3,
EN 61000-4-8 (PFMF) Level 1,
EN 61000-4-11
Shock: IEC 60068-2-27
Freefall: IEC 60068-2-32
Vibration: IEC 60068-2-6