Specifications

Industrial Networking Solutions
5-17
[e-mail]
www.moxa.com
5
Industrial I/O >
ioLogik E2214
ioLogik E2214
Specifi cations
6 DIs supporting PNP, NPN, and dry contact ›
6 Form A relay outputs (Normal Open) ›
Relay specifi cations: 5 A @ 250 VAC, 5 A @ 30 VDC ›
Instant event messaging by TCP/UDP/email/SNMP-trap ›
DI and Relay counter saved when the power is shut off ›
PC-based confi guration utility and web console ›
Power On default relay status setting with sequence ›
Easy-to-use Click&Go™ Logic for local output control ›
Windows/WinCE VB/VC.NET and Linux C APIs ›
I/O control over Modbus/TCP and SNMP protocol ›
Introduction
Remote Ethernet Relay Control
The ioLogik E2214 is a stand-alone Active Ethernet I/O product with 6
digital inputs and 6 relay outputs. The DIN-Rail mountable E2214 can
be connected to digital switches, alarm lights, buzzers, and warning
sirens over Ethernet and IP-based networks. The ioLogik E2214 also
Pin Assignment
Ordering Information
I/O (left to right)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DI.COM1 DI0 DI1 DI2 GND DI.COM2 DI3 DI4 DI5 GND R0 NO R0 C R1 NO R1 C R2 NO R2 C R3 NO R3 C R4 NO R4 C R5 NO R5 C
DI Group 1 DI Group 2
Relays 0 to 5
Active Ethernet I/O with 6 digital inputs and 6 relay outputs
records the built-in relay output usage counter. Even when a sudden
power failure is encountered, the ioLogik E2214 will still be able to
record the relay output usage counter in its internal memory before the
power shuts down completely.
Digital Input
Channels: 6, source/sink selectable
Sensor Type: NPN, PNP, and Dry contact
I/O Mode: DI or Event Counter (up to 900 Hz)
Dry Contact:
• Logic 0: short to GND
• Logic 1: open
Wet Contact:(For Source Type)
• Logic 0: 0 to 3 VDC
• Logic 1: 10 to 30 VDC (DI COM to DI)
Common Type: 6 points per COM
Isolation: 3K VDC or 2K Vrms
Counter/Frequency: 900 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Over-voltage Protection: 36 VDC
Poweroff Counter Memory: 48 bytes
Relay Counter Saving: Yes
Relay Output
Channels: 6 Form A (N.O.) relay outputs, 5A
Contact Rating: 5 A @ 30 VDC, 5 A @ 250 VAC, 5 A @ 110 VAC
Inductance Load: 2 A
Resistance Load: 5 A
Breakdown Voltage: 500 VAC
Relay On/Off Time: 10 ms, 5 ms (Max.)
Initial Insulation Resistance: 1G min. @ 500 VDC
Expected Life: 100,000 times (Typical)
Initial Contact Resistance: 30 milli-ohms (Max.)
Pulse Output: 0.3 Hz at rated load
ioLogik E2214: Active Ethernet I/O with 6 digital inputs and 6 relay outputs
LDP1602: LCD module with 16 x 2 text display and 5 buttons
The certifi cation logos shown here apply to some or all of the products in this
section. For details, see “Regulatory Approvals” under “Specifi cations” below.