Moxa EtherDevice™ Switch EDS-600 Series Hardware Installation Guide First Edition, August 2009 © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan, R.O.C.
Package Checklist The Moxa EDS-600 series is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance.
Panel Views of the EDS-608 FRONT VIEW 8 1 2 4 7 6 8 5 3 REAR VIEW 10 9 Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3. Fast Ethernet Interface Module 4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output 5. Grounding screw 6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring 7. RS-232 Console port 8. Screw to attach Fast Ethernet Interface Module Rear Panel: 9. DIN-Rail Attachment Plate 10.
Panel Views of the EDS-611 FRONT VIEW 10 9 1 8 2 4 7 6 5 9 3 REAR VIEW 12 11 Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3. Fast Ethernet Interface Module 4. Terminal block for 2 power inputs, 1 DI/DO, and 1 Relay output 5. Grounding screw 6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring 7. 8. RS-232 Console port G1 to G3: 10/100/1000 BaseT(X) or 100/1000Base SFP slot combo ports 9. Screw to attach Fast Ethernet Interface Module 10.
Panel Views of the EDS-616 FRONT VIEW 8 1 2 4 7 6 8 5 3 REAR VIEW 9 10 Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3. Fast Ethernet Interface Module 4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output 5. Grounding screw 6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring 7. RS-232 Console port 8. Screw to attach Fast Ethernet Interface Module Rear Panel: 9. DIN-Rail Attachment Plate 10.
Panel Views of the EDS-619 FRONT VIEW 10 9 1 8 2 4 7 6 9 5 3 REAR VIEW 11 12 Front Panel: 1. System Status LEDs 2. Fast Ethernet Interface Module port LEDs 3. Fast Ethernet Interface Module 4. Terminal block for 2 power inputs, 1 DI/DO, and 1 relay output 5. Grounding screw 6. DIP switches for Ring Master, Ring Coupler, and Turbo Ring 7. 8. RS-232 Console port G1 to G3: 10/100/1000 BaseT(X) or 100/1000Base SFP slot combo ports 9. Screw to attach Fast Ethernet Interface Module 10.
Mounting Dimensions (unit = mm) EDS-608/EDS-611 Front View Side View Rear View Panel Mounting Kit Panel Mounting Kit Rear View DIN-Rail Attachment Plate -7-
EDS-616/EDS-619 Front View Side View Rear View Panel Mounting Kit DIN-Rail Attachment Plate Panel Mounting Kit Rear View DIN-Rail Attachment Plate DIN-Rail Mounting The aluminum DIN-Rail attachment plate should already be fixed to the back panel of the EDS-600 when you take it out of the box. If you need to reattach the DIN-Rail attachment plate to the EDS-600, be sure the spring-loaded bracket is situated towards the bottom, as shown in the following figures.
STEP 2—Insert the top of the DIN-Rail into the top slots on the DIN-Rail attachment plate. STEP 3—The DIN-Rail attachment unit will snap into place as shown in the following illustration. DIN-Rail DIN-Rail To remove the Moxa EDS-600 switch from the DIN-Rail, use a screwdriver to push down the spring-loaded bracket until it locks in place, as shown in the following diagram. Next, rotate the bottom of the switch upwards and then remove the switch from the DIN-Rail.
NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw through one of the keyhole-shaped apertures of the Wall Mounting Plates. Do not screw the screws in all the way—leave about 2 mm to allow room for sliding the wall mount panel between the wall and the screws.
Please read and follow these guidelines: y Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point. NOTE: Do not run signal or communications wiring and power wiring through the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.
Wiring the Relay Contact The EDS-600 has a set of relay outputs. The relay contact uses two of the terminal block’s contacts located on the EDS-600’s front panel. Refer to the next section for detailed instructions on how to connect the wires to the terminal block connector, and how to attach the terminal block connector to the terminal block receptor. In this section, we illustrate the meaning of the two contacts used to connect the relay contact.
Wiring the Digital Inputs The EDS-600 has one set of digital inputs (DIs). Each DI consists of two contacts of the 5-pin terminal block connector on the EDS-600’s front panel, which are used for the one DC input. The top and front views of one of the terminal block connectors are shown here. STEP 1: Insert the negative (ground)/positive DI wires into the ┴ /I1 terminals, respectively. y +13 to +30 V for state “1” y -30 to +3 V for state “0” y Max.
RJ45 (10-pin) to DB9 (F) Cable Wiring Moxa EtherDevice Server COM Port RJ45 Plug Pin 1 RJ45 Connector Female DB9 Connector Cable Wiring 1 DCD 2 DSR 3 RTS GND 4/7 5 TxD 6 RxD 8 CTS 9 DTR 1 6 7 5 3 2 8 4 DCD DTR CTS GND RxD TxD RTS DSR 10/100/1000BaseT(X) Ethernet Port Connection The 10/100/1000BaseT(X) ports located on switch’s front panel are used to connect to Ethernet-enabled devices.
RJ45 (8-pin) to RJ45 (8-pin) Straight-through Cable Wiring Straight-Through Cable Switch Port RJ45 Connector Tx+ TxRx+ RxDD+ DDDC+ DC- NIC Port RJ45 Plug Pin 1 RJ45 Connector Cable Wiring 3 6 1 2 4 5 7 8 3 6 1 2 4 5 7 8 Rx+ RxTx+ TxDC+ DCDD+ DD- RJ45 (8-pin) to RJ45 (8-pin) Cross-over Cable Wiring Cross-Over Cable Switch Port (NIC Port) RJ45 Plug Pin 1 RJ45 Connector (Rx+) (Rx-) (Tx+) (Tx-) (DD+) (DD-) (DC+) (DC-) Tx+ TxRx+ RxDC+ DCDD+ DD- Switch Port (NIC Port) RJ45 Connector Cable Wiring 1 2
ATTENTION This is a Class 1 Laser/LED product. To avoid causing serious damage to your eyes, do not stare directly into the laser beam. Turbo Ring DIP Switch Settings EDS-600 series switches are managed redundant plug-and-play Ethernet switches. The proprietary Turbo Ring protocol was developed by Moxa to provide better network reliability and faster recovery time.
“Turbo Ring V2” DIP Switch Settings DIP 1 DIP 2 DIP 3 DIP 4 ON: Enables the default “Ring Coupling (backup)” port. ON: Enables this EDS as the Ring Master. ON: Enables the default “Ring Coupling” port. ON: Activates DIP switches 1, 2, 3 to configure “Turbo Ring V2” settings. OFF: Do not use this EDS as a ring coupler. OFF: DIP switches 1, 2, 3 will be disabled. OFF: Enables the OFF: This EDS default “Ring will not be the Coupling Ring Master. (primary)” port.
When the EDS-600 is set as the Ring Master of the Turbo Ring or as the Head Blinking of the Turbo Chain and the Turbo Ring or Turbo Chain is down. On CPLR/ TAIL G1/G2/G3 GREEN When the EDS-600 coupling function is enabled to form a back-up path or if it is set as the Tail of the Turbo Chain. Blinking When the Turbo Chain is down. Off To disable the EDS-600’s coupling function. On 10/100 Mbps link is active. AMBER Blinking Data is being transmitted at 10/100 Mbps.
Interface RJ45 Ports 10/100/1000BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X connection Fiber Ports Optional 100/1000Base SFP modules Console Port RS-232 (10-pin RJ45) System LED Indicators PWR1, PWR2, FAULT, MSTR/HEAD, CPLR/TAIL, G1, G2, G3 Module LED Indicators 10/100M for TP port, 100M for Fiber port Alarm Contact Two relay outputs with current carrying capacity of 1 A @ 24 VDC Digital Input Two inputs with the same ground, but electrically isolated from the electroni
Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, and D; ATEX Zone 2, Ex nC nL IIC T4 (Pending) EMI FCC Part 15, EN61000-6-4 EMS EN61000-6-2 EN61000-4-2 (ESD), > level 2 for multi-mode models with ST connectors > level 3 for all other models EN61000-4-3 (RS), Level 3 EN61000-4-4 (EFT), Level 2 EN61000-4-5 (Surge), Level 3 EN61000-4-6 (CS), Level 3 EN61000-4-8 EN61000-4-12 EN61000-4-29 Maritime DNV (Pending), GL (Pending), ABS (Pending), LR (Pending), NKK (Pending) Shock IEC60068-2-27
