Moxa EtherDevice™ Switch EDS-600 Series User’s Manual www.moxa.com/product Second Edition, October 2009 © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
Moxa EtherDevice™ Switch EDS-600 Series User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2009 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of Moxa Inc. All other trademarks or registered marks in this manual belong to their respective manufacturers.
Table of Contents Chapter 1 Introduction ...............................................................................................1-1 Overview .............................................................................................................................. 1-2 Package Checklist................................................................................................................. 1-2 Features .......................................................................................
Search by IP address............................................................................................................. 4-4 Upgrade Firmware................................................................................................................ 4-5 Modify IP Address................................................................................................................ 4-6 Export Configuration...........................................................................................
1 Chapter 1 Introduction Welcome to the Moxa EDS-600 Series of compact modular Ethernet switches designed for connecting Ethernet-enabled devices in industrial field applications.
EDS-600 Series User’s Manual Introduction Overview The versatile modular design of the compact EDS-600series Ethernet switches allow users to combine fiber and copper modules to create tailored switch solutions to fit any automation network. The EDS-600’s modular design allows you to install up to 16 fast Ethernet ports and 3 Gigabit fiber optic ports. The Turbo Ring/Turbo Chain (recovery time < 20 ms) technology and STP/RSTP (IEEE 802.
2 Chapter 2 Getting Started This chapter explains how to access the EDS-600 for the first time. There are three ways to access the switch: serial console, Telnet console, and web browser. The serial console connection method, which requires using a short serial cable to connect the EDS-600 to a PC’s COM port, can be used if you do not know the EDS-600’s IP address. The Telnet console and web browser connection methods can be used to access the EDS-600 over an Ethernet LAN, or over the Internet.
EDS-600 Series User’s Manual Getting Started RS-232 Console Configuration (115200, None, 8, 1, VT100) NOTE NOTE Connection Caution! 1. You cannot connect to the EDS-600 simultaneously by serial console and Telnet. 2. You can connect to the EDS-600 simultaneously by web browser and serial console, or by web browser and Telnet. However, we strongly suggest that you do NOT use more than one connection method at the same time.
EDS-600 Series User’s Manual Getting Started 3. The Communication Parameter page of the Property window opens. Select the appropriate COM port for Console Connection, 115200 for Baud Rate, 8 for Data Bits, None for Parity, and 1 for Stop Bits. 4. Click the Terminal tab, and select VT100 for Terminal Type. Click OK to continue. 5. Type 1 to select ansi/VT100 terminal type, and then press Enter.
EDS-600 Series User’s Manual Getting Started 6. The Console login screen will appear. Press Enter to open the Account pop-up selector and then select either admin or user. Use the keyboard’s down arrow to move the cursor to the Password field, enter the Console Password (this is the same as the Web Browser password; leave the Password field blank if a console password has not been set), and then press Enter. 7. The EDS-600’s Main Menu will be displayed.
EDS-600 Series User’s Manual 8. Getting Started After entering the Main Menu, use the following keys to move the cursor, and to select options. Key Up/Down/Left/Right arrows, or Tab Enter Space Esc Function Move the onscreen cursor Display & select options Toggle options Previous Menu Configuration using a Telnet Console You may use Telnet to access the EDS-600’s console utility over a network.
EDS-600 Series User’s Manual NOTE Getting Started 3. The Console login screen will appear. Press Enter to open the Account pop-up selector and then select either admin or user. Use the keyboard’s down arrow to move the cursor to the Password field, enter the Console Password (this is the same as the Web Browser password; leave the Password field blank if a console password has not been set), and then press Enter. 4.
EDS-600 Series User’s Manual Getting Started NOTE If the EDS-600 is configured for other VLAN settings, you must make sure your PC host is on the management VLAN. NOTE Before accessing the EDS-600’s web browser interface, first connect one of the switch’s RJ45 Ethernet ports to your Ethernet LAN, or connect directly to your PC’s Ethernet card (NIC). You can establish a connection using either a straight-through or cross-over Ethernet cable. NOTE The EDS-600’s default IP is 192.168.127.253.
EDS-600 Series User’s Manual Getting Started You may need to wait a few moments for the web page to be downloaded to your computer. Use the menu tree on the left side of the window to open the function pages to access each of the switch’s functions.
3 Chapter 3 Featured Functions In this chapter, we explain how to access the EDS-600’s configuration options, perform monitoring, and use administration functions. There are three ways to access these functions: RS-232 console, Telnet console, and web browser. The serial console connection method, which requires using a short serial cable to connect the EDS-600 to a PC’s COM port, can be used if you do not know the EDS-600’s IP address.
EDS-600 Series User’s Manual Featured Functions Configuring Basic Settings The Basic Settings group includes the most commonly used settings required by administrators to maintain and control EDS-600. System Identification The system identification items are displayed at the top of the web page, and will be included in alarm emails. Entering the system identification information makes it easier to identify the different switches connected to your network. Switch Name Setting Max.
EDS-600 Series User’s Manual Featured Functions Web Auto-logout(s) Setting 60 to 86400 (seconds) Description Disable or extend the auto-logout time for the web management console. Factory Default 0 (disable) Description The length of time that a MAC address entry can remain in the Moxa switch. When an entry reaches its aging time, it “ages out” and is purged from the switch, effectively cancelling frame forwarding to that specific port.
EDS-600 Series User’s Manual Featured Functions Account Setting admin user Description “admin” privilege allows the user to modify all EDS-600 configurations. “user” privilege only allows viewing EDS-600 configurations. Factory Default admin Password Setting Old Password (Max. 16 Characters) New Password (Max. 16 Characters) Retype Password (Max.
EDS-600 Series User’s Manual Featured Functions The following table shows additional configuration examples: Allowable Hosts Any host 192.168.1.120 192.168.1.1 to 192.168.1.254 192.168.0.1 to 192.168.255.254 192.168.1.1 to 192.168.1.126 192.168.1.129 to 192.168.1.254 Input format Disable 192.168.1.120 / 255.255.255.255 192.168.1.0 / 255.255.255.0 192.168.0.0 / 255.255.0.0 192.168.1.0 / 255.255.255.128 192.168.1.128 / 255.255.255.
EDS-600 Series User’s Manual Featured Functions Speed Setting Auto 100M-Full 100M-Half 10M-Full 10M-Half Description Factory Default Allows the port to use the IEEE 802.3u protocol to negotiate with connected devices. The port and connected devices will determine the best speed for that connection. Auto Choose one of these fixed speed options if the opposing Ethernet device has trouble auto-negotiating line speed.
EDS-600 Series User’s Manual Featured Functions Network The Network configuration allows users to configure both IPv4 and IPv6 parameters for management access over the network. The EDS-600 series supports both IPv4 and IPv6, and can be managed through either of these address types. IPv4 The IPv4 settings include the switch’s IP address and subnet mask, as well as the IP address of the default gateway. In addition, input cells are provided for the IP addresses of a 1st and 2nd DNS server.
EDS-600 Series User’s Manual Featured Functions Global Unicast Address Setting None Description Factory Default Displays the IPv6 Global Unicast address. The None network portion of the Global Unicast address can be configured by specifying the Global Unicast Prefix and using a EUI-64 interface ID in the low order 64 bits.
EDS-600 Series User’s Manual NOTE Featured Functions The EDS-600 does not have a real time clock. The user must update the Current Time and Current Date to set the initial time for the EDS-600 after each reboot, especially when the network does not have an Internet connection for an NTP server or there is no NTP server on the LAN. Current Time Setting User adjustable time. Description Factory Default The time parameter allows configuration of the None (hh:mm:ss) local time in local 24-hour format.
EDS-600 Series User’s Manual NOTE Featured Functions Changing the time zone will automatically correct the current time. You should configure the time zone before setting the time. Time Server IP/Name Setting 1st Time Server IP/Name 2nd Time Server IP/Name Description IP or Domain address (e.g., 192.168.1.1 or time.stdtime.gov.tw or time.nist.gov). The EDS-600 will try to locate the 2nd NTP Server if the 1st NTP Server fails to connect.
EDS-600 Series User’s Manual Featured Functions Can Ethernet switches be designed to avoid the effects of these fluctuations? A switch may be designed to support IEEE 1588 while avoiding the effects of queuing.
EDS-600 Series User’s Manual Featured Functions PTP Setting Operation IEEE 1588/PTP Setting Operation Description Disable or enable IEEE 1588(PTP) operation Factory Default Disable Configuration IEEE 1588/PTP Setting Clock Mode Sync Interval Sub-domain Name Description Support software-based IEEE 1588(PTP) mode Period for sending synchronization message (in seconds) Support _DFLT(Default) domain only Factory Default Disable Disable _DFLT Status Setting Offset To Master (nsec) Grandmaster UUID Paren
EDS-600 Series User’s Manual Featured Functions Turbo Ring DIP Switch The Turbo Ring DIP Switch page allows users to disable the four DIP switches located on the EDS’s outer casing. When enabled, the DIP switches can be used to configure basic settings for either the “Turbo Ring” protocol or “Turbo Ring V2” protocol. A complete description of the settings is given below.
EDS-600 Series User’s Manual Featured Functions Set DIP switch as Turbo Ring / Set DIP switch as Turbo Ring V2 Setting Set DIP switch as Turbo Ring Set DIP switch as Turbo Ring V2 NOTE Description Factory Default This is the default if you do NOT reset the switch to Select this option to enable the Turbo Ring DIP factory default settings switches to configure the EDS for a “Turbo (provided you upgraded the Ring” ring. firmware for Turbo Ring V2).
EDS-600 Series User’s Manual Featured Functions “Turbo Ring V2” DIP Switch Settings DIP 1 DIP 2 ON: Enables the ON: Enables this EDS default “Ring as the Ring Master. Coupling (backup)” port. OFF: Enables the OFF: This EDS will default “Ring not be the Ring Coupling (primary)” Master. port. NOTE DIP 3 ON: Enables the default “Ring Coupling” port. DIP 4 ON: Activates DIP switches 1, 2, 3 to configure “Turbo Ring V2” settings. OFF: DIP switches 1, OFF: Do not use this EDS as a ring coupler.
EDS-600 Series User’s Manual Featured Functions System File Update—By Remote TFTP The EDS-600 supports saving your configuration file to a remote TFTP server or local host to allow other EDS-600 switches to use the same configuration at a later time, or saving the Log file for future reference. Loading pre-saved firmware or a configuration file from the TFTP server or local host is also supported for easy upgrading or configuration of the EDS-600.
EDS-600 Series User’s Manual Featured Functions System File Update—By Local Import/Export Configuration File To export the configuration file of this EDS-600, click Export to save it to the local host. Log File To export the Log file of this EDS-600, click Export and save it to the local host. NOTE Some operating systems will open the configuration file and log file directly in the web page. In such cases, right click Export to save as a file.
EDS-600 Series User’s Manual Featured Functions Auto load system configurations when system boots up Setting Enable Disable Description Enables Auto load system configurations when system boots up Disables Auto load system configurations when system boots up Factory Default Enable Save the current configurations to ABC To export the current configuration file of the EDS-600, click on Save to save it to the ABC.
EDS-600 Series User’s Manual NOTE Featured Functions After activating the Factory Default function, you will need to use the default network settings to re-establish a web-browser or Telnet connection with your EDS-600. Using Port Trunking Link Aggregation allows one or more links to be aggregated together to form a Link Aggregation Group. A MAC client can treat Link Aggregation Groups as if they were a single link.
EDS-600 Series User’s Manual Featured Functions When you activate Port Trunking settings, some advanced functions that you set up with the original ports will either be set to factory default values, or disabled: y y y y y y y y y Communication Redundancy will be set to the factory default Traffic Prioritization will be set to the factory default Port-based VLAN or 802.
EDS-600 Series User’s Manual Featured Functions Trunk Type Setting Static LACP Description Designated Moxa proprietary trunking protocol Designated LACP (IEEE 802.3ad, Link Aggregation Control Protocol) Factory Default Static Static Available Ports/Member Port Setting Member/Available Ports Check box Port Port description Name Speed FDX Flow Control Up Down Description Use Up/Down buttons to add/remove specific ports from available ports to/from trunk group.
EDS-600 Series User’s Manual Featured Functions Configuring SNMP The EDS-600 supports SNMP V1/V2c/V3. SNMP V1, and SNMP V2c use a community string match for authentication, which means that SNMP servers access all objects with read-only or read/write permissions using the community string public/private (default value). SNMP V3, which requires you to select an authentication level of MD5 or SHA, is the most secure protocol. You can also enable data encryption to enhance data security.
EDS-600 Series User’s Manual Featured Functions SNMP Read/Write Settings SNMP Versions Setting V1, V2c, V3, or V1, V2c, or V3 only Description Factory Default Select the SNMP protocol version used to manage the switch. V1, V2c V1, V2c Read Community Setting V1, V2c Read Community Description Factory Default Use a community string match with a maximum of 30 characters for authentication. The SNMP agent accesses all objects with read-only permissions using the community string public.
EDS-600 Series User’s Manual Featured Functions User Auth. Type (for SNMP V1, V2c, V3 and V3 only) Setting No-Auth MD5-Auth SHA-Auth Description Use admin account or user account to access objects. No authentication. Provides authentication based on the HMAC-MD5 algorithms. 8-character passwords are the minimum requirement for authentication. Provides authentication based on the HMAC-SHA algorithms. 8-character passwords are the minimum requirement for authentication.
EDS-600 Series User’s Manual Featured Functions 1st Trap Server IP/Name Setting IP or Name Description Enter the IP address or name of the 1st Trap Server used by your network. Factory Default None 1st Trap Community Setting Character String Description Use a community string match for authentication (maximum of 30 characters). Factory Default Public 2nd Trap Server IP/Name Setting IP or Name Description Enter the IP address or name of the 2nd Trap Server used by your network.
EDS-600 Series User’s Manual Featured Functions Using Communication Redundancy Setting up Communication Redundancy on your network helps protect critical links against failure, protects against network loops, and keeps network downtime at a minimum. The Communication Redundancy function allows the user to set up redundant loops in the network to provide a backup data transmission route in the event that a cable is inadvertently disconnected or damaged.
EDS-600 Series User’s Manual NOTE Featured Functions Port trunking and Turbo Ring can be enabled simultaneously to form a backbone. Doing so will increase the bandwidth of the backbone, and also provide redundancy. For example, suppose that two physical ports, 1 and 2, are trunked to form trunk group Trk1, and then Trk1 is set as one Turbo Ring path, if port 1 gets disconnected, the remaining trunked port, port 2, will share the traffic.
EDS-600 Series User’s Manual Featured Functions The user does not need to configure any of the switches as the master to use Turbo Ring or Turbo Ring V2. If none of the switches in the ring is configured as the master, then the protocol will automatically assign master status to one of the switches. In fact, the master is only used to identify which segment in the redundant ring acts as the backup path.
EDS-600 Series User’s Manual Featured Functions When the number of EDS units in the Turbo Ring is odd. If there are 2N+1 EDS units (an odd number) in the “Turbo Ring” ring, with EDS units and segments labeled counterclockwise, then segment N+1 will serve as the backup path. Master For the example shown here, N=1, so that N+1=2.
EDS-600 Series User’s Manual Featured Functions Ring Coupling Configuration For some systems, it may not be convenient to connect all devices in the system to create one BIG redundant ring, since some devices could be located in a remote area. For these systems, “Ring Coupling” can be used to separate the devices into different smaller redundant rings, but in such a way that they can still communicate with each other.
EDS-600 Series User’s Manual Featured Functions The coupler switch (i.e., Switch A) will monitor switch B through the coupling control port to determine whether or not the coupling port’s backup path should be recovered. Ring Coupling for a “Turbo Ring V2” Ring Switch B Switch D Coupling Port (Primary) Main Path Backup Path Coupling Port (Backup) Switch C Switch A Note that the ring coupling settings for a “Turbo Ring V2” ring are different from a “Turbo Ring” ring.
EDS-600 Series User’s Manual Featured Functions Dual-Ring Configuration (applies only to “Turbo Ring V2”) The “dual-ring” option provides another ring coupling configuration, in which two adjacent rings share one switch. This type of configuration is ideal for applications that have inherent cabling difficulties.
EDS-600 Series User’s Manual Featured Functions Configuring “Turbo Ring” and “Turbo Ring V2” Use the Communication Redundancy page to configure select “Turbo Ring” or “Turbo Ring V2” or “Turbo Chain” Note that configuration pages for these two protocols are different. Configuring “Turbo Ring” Explanation of “Current Status” Items Now Active Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP, or none.
EDS-600 Series User’s Manual Featured Functions Explanation of “Settings” Items Redundancy Protocol Setting Turbo Ring Description Select this item to change to the Turbo Ring configuration page. Turbo Ring V2 Select this item to change to the Turbo Ring V2 configuration page. Turbo Chain Select this item to change to the Turbo Chain configuration page. RSTP (IEEE 802.1W/1D) Select this item to change to the RSTP configuration page.
EDS-600 Series User’s Manual Featured Functions Coupling Control Port Setting Description Factory Default EDS-608: port 2-1 Select any port of the EDS to be the EDS-611: port 2-4 Coupling Control Port coupling control port EDS-616: port 4-1 EDS-619: port 4-4 Configuring “Turbo Ring V2” NOTE When using the Dual-Ring architecture, users must configure settings for both Ring 1 and Ring 2. In this case, the status of both rings will appear under “Current Status.
EDS-600 Series User’s Manual Featured Functions Explanation of “Current Status” Items Now Active Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, Turbo Chain, RSTP, or none. Ring 1/2—Status Shows Healthy if the ring is operating normally, and shows Break if the ring’s backup link is active. Ring 1/2—Master/Slave Indicates whether or not this EDS is the Master of the Turbo Ring. (This field appears only when selected to operate in Turbo Ring or Turbo Ring V2 mode.
EDS-600 Series User’s Manual Featured Functions Enable Ring 1 Setting Description Enabled Enable the Ring 1 settings Disabled Disable the Ring 1 settings Factory Default Not checked Enable Ring 2* Setting Enabled Description Enable the Ring 2 settings Disabled Disable the Ring 2 settings Factory Default Not checked *You should enable both Ring 1 and Ring 2 when using the Dual-Ring architecture.
EDS-600 Series User’s Manual Featured Functions Coupling Mode Setting Dual Homing Ring Coupling (backup) Ring Coupling (primary) NOTE Description Select this item to change to the Dual Homing configuration page Select this item to change to the Ring Coupling (backup) configuration page Select this item to change to the Ring Coupling (primary) configuration page The Turbo Ring DIP Switches located on the EDS-600’s outer casing can be used to configure the EDS’s Turbo Ring protocols.
EDS-600 Series User’s Manual Featured Functions The Turbo Chain Concept Moxa’s Turbo Chain is an advanced software-technology that gives network administrators the flexibility of constructing any type of redundant network topology. When using the “chain” concept, you first connect the Ethernet switches in a chain and then simply link the two ends of the chain to an Ethernet network, as illustrated in the following figure. Turbo Chain can be used on industrial networks that have a complex topology.
EDS-600 Series User’s Manual Featured Functions Configuring “Turbo Chain” Head Switch Configuration Member Switch Configuration 3-40
EDS-600 Series User’s Manual Featured Functions Tail Switch Configuration Explanation of “Current Status” Items Now Active Shows which communication protocol is in use: Turbo Ring, Turbo Ring V2, RSTP, Turbo Chain or None. The “Ports Status” indicators show Forwarding for normal transmission, Blocked if this port is connected to the Tail port as a backup path and the path is blocked, and Link down if there is no connection.
EDS-600 Series User’s Manual Featured Functions Head Role Setting Head Port Member Port Description Factory Default EDS-608: port 2-3 Select any port of the EDS to be the EDS-611: port G2 head port. EDS-616: port 4-3 EDS-619: port G2 EDS-608: port 2-4 Select any port of the EDS to be the EDS-611: port G3 member port.
EDS-600 Series User’s Manual Featured Functions The STP/RSTP Concept Spanning Tree Protocol (STP) was designed to help reduce link failures in a network, and provide protection from loops. Networks that have a complicated architecture are prone to broadcast storms caused by unintended loops in the network. Moxa EDS-600’s STP feature is disabled by default. To be completely effective, you must enable RSTP/STP on every EDS-600 connected to your network.
EDS-600 Series User’s Manual Featured Functions If STP is enabled, it will detect duplicate paths and prevent, or block, one of them from forwarding traffic. In the following example, STP determined that traffic from LAN segment 2 to LAN segment 1 should flow through Bridges C and A because this path has a greater bandwidth and is therefore more efficient.
EDS-600 Series User’s Manual Featured Functions How STP Works When enabled, STP determines the most appropriate path for traffic through a network. The way it does this is outlined in the sections below. STP Requirements Before STP can configure the network, the system must satisfy the following requirements: y Communication between all the bridges. This communication is carried out using Bridge Protocol Data Units (BPDUs), which are transmitted in packets with a known multicast address.
EDS-600 Series User’s Manual Featured Functions STP Reconfiguration Once the network topology has stabilized, each bridge listens for Hello BPDUs transmitted from the Root Bridge at regular intervals. If a bridge does not receive a Hello BPDU after a certain interval (the Max Age time), the bridge assumes that the Root Bridge, or a link between itself and the Root Bridge, has gone down. This will trigger the bridge to reconfigure the network to account for the change.
EDS-600 Series User’s Manual y y y y y y Featured Functions Bridge A has been selected as the Root Bridge, since it was determined to have the lowest Bridge Identifier on the network. Since Bridge A is the Root Bridge, it is also the Designated Bridge for LAN segment 1. Port 1 on Bridge A is selected as the Designated Bridge Port for LAN Segment 1. Ports 1 of Bridges B, C, X, and Y are all Root Ports sine they are nearest to the Root Bridge, and therefore have the most efficient path.
EDS-600 Series User’s Manual Featured Functions Configuring STP/RSTP The following figures indicate which Spanning Tree Protocol parameters can be configured. A more detailed explanation of each parameter follows. At the top of this page, the user can check the “Current Status” of this function. For RSTP, you will see: Now Active: This will show which communication protocol is being used—Turbo Ring, RSTP, or neither. Root/Not Root This field will appear only when selected to operate in RSTP mode.
EDS-600 Series User’s Manual Featured Functions Forwarding Delay Setting Numerical value input by user Description The amount of time this device waits before checking to see if it should change to a different state. Factory Default 15 (sec.) Description The root of the Spanning Tree topology periodically sends out a “hello” message to other devices on the network to check if the topology is healthy. The “hello time” is the amount of time the root waits between sending hello messages.
EDS-600 Series User’s Manual Featured Functions Port Status Indicates the current Spanning Tree status of this port. “Forwarding” for normal transmission, or “Blocking” to block transmission. Configuration Limits of RSTP/STP The Spanning Tree Algorithm places limits on three of the configuration items described previously: [Eq. 1]: 1 sec ≦ Hello Time ≦ 10 sec [Eq. 2]: 6 sec ≦ Max. Age ≦ 40 sec [Eq.
EDS-600 Series User’s Manual Featured Functions The Traffic Prioritization Concept What is Traffic Prioritization? Traffic prioritization allows you to prioritize data so that time-sensitive and system-critical data can be transferred smoothly and with minimal delay over a network. The benefits of using traffic prioritization are: y y y y Improve network performance by controlling a wide variety of traffic and managing congestion. Assign priorities to different categories of traffic.
EDS-600 Series User’s Manual Featured Functions Even though the IEEE 802.1D standard is the most widely used prioritization scheme in the LAN environment, it still has some restrictions: y y It requires an additional 4-byte tag in the frame, which is normally optional in Ethernet networks. Without this tag, the scheme cannot work. The tag is part of the IEEE 802.1Q header, so to implement QoS at layer 2, the entire network must implement IEEE 802.1Q VLAN tagging.
EDS-600 Series User’s Manual Featured Functions EDS-600 supports two different queuing mechanisms: y y Weight Fair: This method services all the traffic queues, giving priority to the higher priority queues. Under most circumstances, this method gives high priority precedence over low-priority, but in the event that high-priority traffic exceeds the link capacity, lower priority traffic is not blocked.
EDS-600 Series User’s Manual Featured Functions Port Highest Priority Setting Enable/Disable Description Set the Port Priority of the ingress frames to “High” queues. Factory Default Disable Inspect TOS Setting Enable/Disable Description Factory Default Select the option to enable EDS-600 to inspect the Type Enable of Service (TOS) bits in IPV4 frame to determine the priority of each frame.
EDS-600 Series User’s Manual Setting Low/Normal/ Medium/High Featured Functions Description Set the mapping table of different CoS values to 4 different egress queues. Factory 0: Low 1: Low 2: Normal 3: Normal 4: Medium 5: Medium 6: High 7: High TOS/DiffServ Mapping Setting Low/Normal/ Medium/High Description Set the mapping table of different TOS values to 4 different egress queues.
EDS-600 Series User’s Manual Featured Functions Using Virtual LAN Setting up Virtual LANs (VLANs) on your EDS-600 increases the efficiency of your network by dividing the LAN into logical segments, as opposed to physical segments. In general, VLANs are easier to manage. The Virtual LAN (VLAN) Concept What is a VLAN? A VLAN is a group of devices that can be located anywhere on a network, but which communicate as if they are on the same physical segment.
EDS-600 Series User’s Manual Featured Functions Benefits of VLANs The main benefit of VLANs is that they provide a network segmentation system that is far more flexible than traditional networks. Using VLANs also provides you with three other benefits: y y y VLANs ease the relocation of devices on networks: With traditional networks, network administrators spend most of their time dealing with moves and changes.
EDS-600 Series User’s Manual Featured Functions The IEEE Std 802.1Q-1998 defines how VLANs operate within an open packet-switched network. An 802.1Q compliant packet carries additional information that allows a switch to determine which VLAN the port belongs. If a frame is carrying the additional information, it is known as a tagged frame.
EDS-600 Series User’s Manual Featured Functions Management VLAN ID Setting VLAN ID ranges from 1 to 4094 Description Set the management VLAN of this EDS-600. Factory Default 1 Port Type Setting Access Trunk Description This port type is used to connect single devices without tags. Select “Trunk” port type to connect another 802.1Q VLAN aware switch or another LAN that combines tagged and/or untagged devices and/or other switches/hubs.
EDS-600 Series User’s Manual Featured Functions To configure the EDS-600’s Port-based VLAN, use the VLAN Setting page to configure the ports. VLAN Mode Setting Description 802.1Q VLAN Set VLAN mode to 802.1Q VLAN Port-based VLAN Set VLAN mode to Port-based VLAN Factory Default 802.1Q VLAN Port Setting Enable/Disable Description Set port to specific VLAN Group.
EDS-600 Series User’s Manual Featured Functions In 802.1Q VLAN table, you can review the VLAN groups that were created, Joined Access Ports, and Trunk Ports, and in Port-based VLAN table, you can review the VLAN group and Joined port. NOTE The physical network can have a maximum of 64 VLAN settings. Using Multicast Filtering Multicast filtering improves the performance of networks that carry multicast traffic.
EDS-600 Series User’s Manual Featured Functions Multicast Filtering Multicast filtering ensures that only end-stations that have joined certain groups receive multicast traffic. With multicast filtering, network devices only forward multicast traffic to the ports that are connected to registered end-stations. The following two figures illustrate how a network behaves without multicast filtering, and with multicast filtering.
EDS-600 Series User’s Manual Featured Functions Multicast Filtering and Moxa EtherDevice Switch The EDS-600 has three ways to achieve multicast filtering: IGMP (Internet Group Management Protocol) Snooping, GMRP (GARP Multicast Registration Protocol), and adding a static multicast MAC manually to filter multicast traffic automatically. IGMP (Internet Group Management Protocol) Snooping Mode Snooping Mode allows your switch to forward multicast packets only to the appropriate ports.
EDS-600 Series User’s Manual Featured Functions GMRP (GARP Multicast Registration Protocol) The EDS-600 supports IEEE 802.1D-1998 GMRP (GARP Multicast Registration Protocol), which differs from IGMP (Internet Group Management Protocol). GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP provides a mechanism that allows bridges and end stations to register or de-register Group membership information dynamically.
EDS-600 Series User’s Manual Featured Functions IGMP Snooping Enhanced Mode Setting Enable Disable Description IGMP Multicast packets will forward to : y Learned Multicast Querier Ports y Member Ports IGMP Multicast packets will forward to : y Learned multicast Querier Ports y Static Multicast Querier Ports y Querier Connected Ports y Member Ports Factory Default Enable Description Set the query interval of the Querier function globally. Valid settings are from 20 to 600 seconds.
EDS-600 Series User’s Manual Featured Functions IGMP Table The EDS-600 displays the current active IGMP groups that were detected. The information includes VID, Auto-learned Multicast Router Port, Static Multicast Router Port, Querier Connected Port, and the IP and MAC addresses of active IGMP groups. Add Static Multicast MAC If required, the EDS-600 also supports adding multicast groups manually.
EDS-600 Series User’s Manual Featured Functions Configuring GMRP GMRP is a MAC-based multicast management protocol, whereas IGMP is IP-based. GMRP provides a mechanism that allows bridges and end stations to register or un-register Group membership information dynamically. GMRP enable Setting Enable/Disable Description Select the option to enable the GMRP function for the port listed in the Port column GMRP Table The EDS-600 displays the current active GMRP groups that were detected.
EDS-600 Series User’s Manual Featured Functions Using Bandwidth Management In general, one host should not be allowed to occupy unlimited bandwidth, particularly when the device malfunctions. For example, so-called “broadcast storms” could be caused by an incorrectly configured topology, or a malfunctioning device.
EDS-600 Series User’s Manual Featured Functions The IEEE 802.1X Concept Three components are used to create an authentication mechanism based on 802.1X standards: Client/Supplicant, Authentication Server, and Authenticator. Supplicant: The end station that requests access to the LAN and switch services and responds to the requests from the switch. Authentication server: The server that performs the actual authentication of the supplicant.
EDS-600 Series User’s Manual 1. 2. 3. 4. 5. 6. 7. Featured Functions When the supplicant receives an “EAP Request/Identity” frame, it sends an “EAP Response/Identity” frame with its username back to the authenticator. If the RADIUS server is used as the authentication server, the authenticator relays the “EAP Response/Identity” frame from the supplicant by encapsulating it into a “RADIUS Access-Request” frame and sends to the RADIUS server.
EDS-600 Series User’s Manual Featured Functions Configuring IEEE 802.1X Database Option Setting Local (Max. 32 users) Radius Radius, Local Description Factory Default Select this option when setting the Local User Database Local as the authentication database. Select this option to set an external RADIUS server as Local the authentication database. The authentication mechanism is “EAP-MD5.” Select this option to make an external RADIUS server as Local the authentication database with first priority.
EDS-600 Series User’s Manual Featured Functions Re-Auth Setting Enable/Disable Description Select to require re-authentication of the client after a preset time period of no activity has elapsed. Factory Default Disable Description Specify how frequently the end stations need to reenter usernames and passwords in order to stay connected. Factory Default 3600 Description Select the option under the 802.1X column to enable IEEE 802.1X for one or more ports.
EDS-600 Series User’s Manual Featured Functions Local User Database Setup When setting the Local User Database as the authentication database, set the database first. Local User Database Setup Setting User Name (Max. 30 characters) Password (Max. 16 characters) Description (Max.
EDS-600 Series User’s Manual Featured Functions Using Auto Warning Since industrial Ethernet devices are often located at the endpoints of a system, these devices will not always know what is happening elsewhere on the network. This means that an industrial Ethernet switch that connects to these devices must provide system maintainers with real-time alarm messages.
EDS-600 Series User’s Manual Featured Functions Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of a specific port. System Events Warning e-mail is sent when… Switch Cold Start Power is cut off and then reconnected. Switch Warm Start The EDS-600 is rebooted, such as when network parameters are changed (IP address, subnet mask, etc.).
EDS-600 Series User’s Manual NOTE Featured Functions Warning e-mail messages will have the sender field formatted as follows: Moxa EDS-608, 00000@Switch_Location Moxa EDS-611, 00000@Switch_Location Moxa EDS-616, 00000@Switch_Location Moxa EDS-619, 00000@Switch_Location where Moxa EDS-XXX is the default Switch Name, 00000 is the EDS-600’s serial number, and Switch_Location is the default Server Location. Refer to the Basic Settings section to see how to modify Switch Name and Switch Location.
EDS-600 Series User’s Manual Featured Functions Password Setting Setting Description Disable/Enable to To reset the Password from the Web Browser interface, change Password click the Change password check-box, type the Old Password, type the New Password, retype the New password, and then click Activate; Max. 45 Characters. Old Password Type the current password when changing the password New Password Type new password when enabled to change password; Max. 45 Characters.
EDS-600 Series User’s Manual Featured Functions Event Setup Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of a specific port. The EDS-600 supports two relay outputs. You can configure which relay output is related to which events. This helps administrators identify the importance of the different events.
EDS-600 Series User’s Manual Featured Functions Port Events Link-ON Link-OFF Traffic-Overload Traffic-Threshold (%) Traffic-Duration (sec.) NOTE Warning e-mail is sent when… The port is connected to another device. The port is disconnected (e.g., the cable is pulled out, or the opposing device shuts down). The port’s traffic surpasses the Traffic-Threshold for that port (provided this item is Enabled). Enter a non-zero number if the port’s Traffic-Overload item is Enabled.
EDS-600 Series User’s Manual Featured Functions Using Line-Swap-Fast-Recovery The Line-Swap Fast Recovery function, which is enabled by default, allows the EDS-600 to return to normal operation extremely quickly after devices are unplugged and then re-plugged into different ports. The recovery time is on the order of a few milliseconds (compare this with standard commercial switches for which the recovery time could be on the order of several minutes).
EDS-600 Series User’s Manual Featured Functions Perform the following steps to use the Set device IP function: STEP 1—set up the connected devices Set up those Ethernet-enabled devices connected to the EDS-600 for which you would like IP addresses to be assigned automatically. The devices must be configured to obtain their IP address automatically. The devices’ configuration utility should include a setup page that allows you to choose an option similar to Obtain an IP address automatically.
EDS-600 Series User’s Manual Featured Functions The DHCP Relay Agent makes it possible for DHCP broadcast messages to be sent over routers. The DHCP Relay Agent enables DHCP clients to obtain IP addresses from a DHCP server on a remote subnet, or those that are not located on the local subnet. DHCP Option 82 Option 82 is used by the relay agent to insert additional information into the client’s DHCP request.
EDS-600 Series User’s Manual Featured Functions Server IP Address 1st Server Setting IP address for the 1st DHCP server Description This assigns the IP address of the 1st DHCP server that the switch tries to access. Factory Default None 2nd Server Setting IP address for the 2nd DHCP server Description Factory Default This assigns the IP address of the 2nd DHCP server that None the switch tries to access.
EDS-600 Series User’s Manual Featured Functions DHCP Option 82 Enable Option82 Setting Description Enable or Disable Enable or disable DHCP Option 82 function. Factory Default Disable Type Setting IP MAC Client-ID Other Description Use switch IP address as the remote ID sub-option. Use switch MAC address as the remote ID sub-option. Use the combination of switch MAC address and IP address as the remote ID sub-option. Use the user-defined value as the remote ID sub-option.
EDS-600 Series User’s Manual Featured Functions Using Diagnosis The EDS-600 provides two important tools for administrators to diagnose network systems. Mirror Port The Mirror port function can be used to monitor data being transmitted through a specific port. This is done by setting up another port (the mirror port) to receive the same data being transmitted from, or both to and from, the port under observation.
EDS-600 Series User’s Manual Featured Functions Ping The Ping function uses the ping command to give users a simple but powerful tool for troubleshooting network problems. The function’s most unique feature is that even though the ping command is entered from the user’s PC keyboard, the actual ping command originates from the EDS-600 itself. In this way, the user can essentially control the EDS-600 and send ping commands out through its ports.
EDS-600 Series User’s Manual Featured Functions LLDP Web Interface From the switch’s web interface, users have the option of either enabling or disabling the LLDP, as well as setting the LLDP transmit interval (as shown in the figure below). In addition, users are able to view each switch’s neighbor-list, which is reported by its network neighbors.
EDS-600 Series User’s Manual Featured Functions Using Monitor You can monitor statistics in real time from the EDS-600’s web console and serial console. Monitor by Switch Access the Monitor by selecting “System” from the left selection bar. Monitor by System allows the user to view a graph that shows the combined data transmission activity of all the EDS-600’s 18 ports.
EDS-600 Series User’s Manual Featured Functions Monitor by Port Access the Monitor by Port function by selecting ALL 10/100M or 1G Ports or Port i, in which i= 1, 2, …, G2, from the left pull-down list. The Port i options are identical to the Monitor by System function discussed above, in that users can view graphs that show All Packets, TX Packets, RX Packets, or Error Packets activity, but in this case, only for an individual port.
EDS-600 Series User’s Manual Featured Functions The table will display the following information: MAC Type Port This field shows the MAC address This field shows the type of this MAC address This field shows the port that this MAC address belongs to Using Event Log Bootup Date Time System Startup Time Events This field shows how many times the EDS-600 has been rebooted or cold started. The date is updated based on how the current date is set in the “Basic Setting” page.
EDS-600 Series User’s Manual NOTE Featured Functions The following events will be recorded into the EDS-600’s Event Log table: 1. Cold start 2. Warm start 3. Configuration change activated 4. Power 1/2 transition (Off Æ On), Power 1/2 transition (On Æ Off) 5. Authentication fail 6. Topology changed 7. Master setting is mismatched 8. DI 1/2 transition (Off Æ On), DI 1/2 transition (On Æ Off) 9. Port traffic overload 10. dot1x Auth Fail 11.
EDS-600 Series User’s Manual Featured Functions Syslog Server 3 Setting IP Address Port Destination (1 to 65535) NOTE Description Enter the IP address of 3rd Syslog Server used by your network. Enter the UDP port of 3rd Syslog Server. Factory Default None 514 The following events will be recorded into the EDS-600’s Event Log table, and will then be sent to the specified Syslog Server: 1. Cold start 2. Warm start 3. Configuration change activated 4.
EDS-600 Series User’s Manual 3. NOTE Featured Functions Select Yes to enter the EDS-600’s web browser interface and access the web browser interface secured via HTTPS/SSL. Moxa provides a Root CA certificate .After installing this certificate into your PC or notebook, you can access the web browser interface directly and will not see any warning messages again. You may download the certificate from the EDS-600’s CD-ROM.
4 Chapter 4 EDS Configurator GUI EDS Configurator is a comprehensive Windows-based GUI that is used to configure and maintain multiple EDS-600 switches.
EDS-600 Series User’s Manual EDS Configurator GUI Starting EDS Configurator To start EDS Configurator, locate and then run the executable file edscfgui.exe. NOTE You may download the EDS Configurator software from Moxa’s website at www.moxa.com. For example, if the file was placed on the Windows desktop, it should appear as follows. Simply double click on the icon to run the program. The Moxa EtherDevice Server Configurator window will open, as shown below.
EDS-600 Series User’s Manual EDS Configurator GUI Broadcast Search Use the Broadcast Search utility to search the LAN for all EDS-600 switches that are connected to the LAN. Note that since the search is done by MAC address, Broadcast Search will not be able to locate Moxa EtherDevice Servers connected outside the PC host’s LAN. Start by clicking the , or by selecting Broadcast Search under the List Server menu.
EDS-600 Series User’s Manual EDS Configurator GUI Search by IP address This utility is used to search for EDS-600 switches one at a time. Note that the search is conducted by IP address, so you should be able to locate any EDS-600 that is properly connected to your LAN, WAN, or even the Internet. Start by clicking the Specify by IP address icon , or by selecting Specify IP address under the List Server menu. The Search Server with IP Address window will open.
EDS-600 Series User’s Manual EDS Configurator GUI Upgrade Firmware Keep your EDS-600 up to date with the latest firmware from Moxa. Perform the following steps to upgrade the firmware: 1. 2. Download the updated firmware (*.rom) file from the Moxa website (www.moxa.com). Click the switch (from the Moxa EtherDevice Server Configurator window) whose firmware you wish to upgrade to highlight it. 3. Click the Upgrade Firmware toolbar icon , or select Upgrade under the Firmware menu.
EDS-600 Series User’s Manual EDS Configurator GUI Modify IP Address You may use the Modify IP Address function to reconfigure EDS-600’s network settings. Start by clicking the Modify IP address icon , or by selecting Modify IP address under the Configuration menu. The Setup Configuration window will open. Checkmark the box to the left of those items that you wish to modify, and then Disable or Enable DHCP, and enter IP Address, Subnet mask, Gateway, and DNS IP.
EDS-600 Series User’s Manual EDS Configurator GUI Export Configuration The Export Configuration utility is used to save the entire configuration of a particular EDS-600 to a text file. Take the following steps to export a configuration: 1. Highlight the switch (from the Server list in the Configurator window’s left pane), and then click the Export toolbar icon or select Export Configuration from the Configuration menu.
EDS-600 Series User’s Manual 3. EDS Configurator GUI You may use a standard text editor, such as Notepad under Windows, to view and modify the newly created configuration file.
EDS-600 Series User’s Manual EDS Configurator GUI Import Configuration The Import Configuration function is used to import an entire configuration from a text file to the EDS-600. This utility can be used to transfer the configuration from one EDS-600 to another, by first using the Export Configuration function (described in the previous section) to save a switch configuration to a file, and then using the Import Configuration function. Perform the following steps to import a configuration: 1.
EDS-600 Series User’s Manual EDS Configurator GUI 3. The Setup Configuration window will be displayed, with a special note attached at the bottom. Parameters that have been changed will be activated with a checkmark. You may make more changes if necessary, and then click OK to accept the changes. 4. Click Yes in response to the following warning message to accept the new settings.
EDS-600 Series User’s Manual EDS Configurator GUI Unlock Server The Unlock Server function is used to open a password protected switch so that the user can modify its configuration, import/export a configuration, etc. There are six possible responses under the Status column. The Status of an EDS-600 indicates how the switch was located (by Moxa EtherDevice Switch Configurator), and what type of password protection it has.
EDS-600 Series User’s Manual 3. EDS Configurator GUI The status of the switch will now read Unlocked.
A Appendix A MIB Groups The EDS-600 comes with built-in SNMP (Simple Network Management Protocol) agent software that supports cold/warm start trap, line up/down trap, and RFC 1213 MIB-II. The standard MIB groups that the EDS-600 series support are: MIB II.1 – System Group sysORTable MIB II.2 – Interfaces Group ifTable MIB II.4 – IP Group ipAddrTable ipNetToMediaTable IpGroup IpBasicStatsGroup IpStatsGroup MIB II.5 – ICMP Group IcmpGroup IcmpInputStatus IcmpOutputStats MIB II.
EDS-600 Series User’s Manual MIB Groups MIB II.10 – Transmission Group dot3 dot3StatsTable MIB II.11 – SNMP Group SnmpBasicGroup SnmpInputStats SnmpOutputStats MIB II.
EDS-600 Series User’s Manual MIB Groups The EDS-600 also provides a private MIB file, located on the EDS-600 Series utility CD-ROM. Public Traps: 1. Cold Start 2. Link Up 3. Link Down 4. Authentication Failure 5. dot1dBridge New Root 6. dot1dBridge Topology Changed Private Traps: 1. Configuration Changed 2. Power On 3. Power Off 4. Traffic Overloaded 5. Turbo Ring Topology Changed 6. Turbo Ring Coupling Port Changed 7.
B Appendix B Modbus/TCP Map EDS-608 Modbus Information v1.
EDS-600 Series User’s Manual 0x0055 3 word 0x0058 1 word 0x0059 1 word 0x005A 1 word 0x0080 1 word 0x0082 1 word 0x1000~0x1007 1 word 0x1100~0x1107 1 word 0x1200~0x1207 1 word 0x1300~0x1307 1 word Modbus/TCP Map Ethernet MAC Address Ex: MAC = 00-01-02-03-04-05 Word 0 Hi byte = 0x00 Word 0 Lo byte = 0x01 Word 1 Hi byte = 0x02 Word 1 Lo byte = 0x03 Word 2 Hi byte = 0x04 Word 2 Lo byte = 0x05 Power 1 0x0000:Off 0x0001:On Power 2 0x0000:Off 0x0001:On Fault LED Status 0x0000:No 0x0001:Yes DI1
EDS-600 Series User’s Manual 0x1400~0x1413(Port 1) 0x1414~0x1427(Port 2) 20 word 0x2000~0x200F 2 word 0x2100~0x210F 2 word 0x2200~0x220F 2 word 0x2300~0x230F 2 word 0x3000 1 word 0x3100 1 word 0x3200~0x3207 1 word 0x3300 1 word Modbus/TCP Map Port 1~8 Description Port Description = "100TX,RJ45." Word 0 Hi byte = ‘1’ Word 0 Lo byte = ‘0’ Word 1 Hi byte = ‘0’ Word 1 Lo byte = ‘T’ … Word 4 Hi byte = ‘4’ Word 4 Lo byte = ‘5’ Word 5 Hi byte = ‘.
EDS-600 Series User’s Manual 0x3301 1 word 0x3302 1 word 0x3303 1 word 0x3304 1 word 0x3305 1 word 0x3500 1 word 0x3501 1 word Modbus/TCP Map TR 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR Coupling 0x0000:Off 0x0001:On 0xFFFF:Turbo Ring Not Enable TR Coupling Port status 0x0000:Port Disa
EDS-600 Series User’s Manual 0x3502 1 word 0x3600 1 word 0x3601 1 word 0x3602 1 word 0x3603 1 word 0x3680 1 word 0x3681 1 word 0x3682 1 word Modbus/TCP Map TR2 Coupling Port Backup status (Only using in Dual Homing) 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:
EDS-600 Series User’s Manual 0x3683 1 word 0x3700 1 word 0x3701 1 word 0x3702 1 word Modbus/TCP Map TR2 Ring 2 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 2 Not Enable Turbo Chain Switch Role Mode 0x0000:Head Switch 0x0001:Member Switch 0x0002:Tail Switch 0xFFFF:Turbo Chain Not Enable Turbo Chain 1st Port Status 0x0000:Link Down 0x0001:Blocking 0x0002:Blocked 0x0003:Forwarding 0xFFFF:Turbo Chain
EDS-600 Series User’s Manual Modbus/TCP Map EDS-611 Modbus Information v1.
EDS-600 Series User’s Manual 0x005A 1 word 0x0080 1 word 0x0082 1 word 0x1000~0x100A 1 word 0x1100~0x110A 1 word 0x1200~0x120A 1 word 0x1300~0x130A 1 word 0x1400~0x1413(Port 1) 0x1414~0x1427(Port 2) 20 word 0x2000~0x2015 2 word 0x2100~0x2115 2 word Modbus/TCP Map Fault LED Status 0x0000:No 0x0001:Yes DI1 0x0000:Off 0x0001:On DO1 0x0000:Off 0x0001:On Port Information Port 1~11 Status 0x0000:Link down 0x0001:Link up 0x0002:Disable 0xFFFF:No port Port 1~11 Speed 0x0000:10M-Half 0x0001:10M-F
EDS-600 Series User’s Manual 0x2200~0x2215 2 word 0x2300~0x2315 2 word 0x3000 1 word 0x3100 1 word 0x3200~0x320A 1 word 0x3300 1 word 0x3301 1 word 0x3302 1 word 0x3303 1 word Modbus/TCP Map port 1~11 Tx Error Packets Ex: port 1 Tx Error Packets = 0x44332211 Word 0 = 4433 Word 1 = 2211 port 1~11 Rx Error Packets Ex: port 1 Rx Error Packets = 0x44332211 Word 0 = 4433 Word 1 = 2211 Redundancy Information Redundancy Protocol 0x0000:None 0x0001:RSTP 0x0002:Turbo Ring 0x0003:Turbo Ring V2 0x000
EDS-600 Series User’s Manual 0x3304 1 word 0x3305 1 word 0x3500 1 word 0x3501 1 word 0x3502 1 word 0x3600 1 word 0x3601 1 word Modbus/TCP Map TR Coupling Port status 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0005:Forwarding 0xFFFF:Turbo Ring Not Enable TR Coupling Control Port status 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0005:Forwarding 0x0006:Inactive 0x0007:Active 0xFFFF:Turbo Ring Not Enable TR2 Coupling Mode 0x
EDS-600 Series User’s Manual 0x3602 1 word 0x3603 1 word 0x3680 1 word 0x3681 1 word 0x3682 1 word 0x3683 1 word 0x3700 1 word 0x3701 1 word Modbus/TCP Map TR2 Ring 1 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not Enable TR2 Ring 1 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not
EDS-600 Series User’s Manual 0x3702 1 word Modbus/TCP Map Turbo Chain 2nd Port Status 0x0000:Link Down 0x0001:Blocking 0x0002:Blocked 0x0003:Forwarding 0xFFFF:Turbo Chain Not Enable Memory mapping from address 0x0000 ~ 0x3FFF. EDS-616 Modbus Information v1.
EDS-600 Series User’s Manual 0x0055 3 word 0x0058 1 word 0x0059 1 word 0x005A 1 word 0x0080 1 word 0x0082 1 word 0x1000~0x100F 1 word 0x1100~0x110F 1 word 0x1200~0x120F 1 word 0x1300~0x130F 1 word Modbus/TCP Map Ethernet MAC Address Ex: MAC = 00-01-02-03-04-05 Word 0 Hi byte = 0x00 Word 0 Lo byte = 0x01 Word 1 Hi byte = 0x02 Word 1 Lo byte = 0x03 Word 2 Hi byte = 0x04 Word 2 Lo byte = 0x05 Power 1 0x0000:Off 0x0001:On Power 2 0x0000:Off 0x0001:On Fault LED Status 0x0000:No 0x0001:Yes DI1
EDS-600 Series User’s Manual 0x1400~0x1413(Port 1) 0x1414~0x1427(Port 2) 20 word 0x2000~0x201F 2 word 0x2100~0x211F 2 word 0x2200~0x221F 2 word 0x2300~0x231F 2 word 0x3000 1 word 0x3100 1 word 0x3200~0x320F 1 word 0x3300 1 word Modbus/TCP Map Port 1~16 Description Port Description = "100TX,RJ45." Word 0 Hi byte = ‘1’ Word 0 Lo byte = ‘0’ Word 1 Hi byte = ‘0’ Word 1 Lo byte = ‘T’ … Word 4 Hi byte = ‘4’ Word 4 Lo byte = ‘5’ Word 5 Hi byte = ‘.
EDS-600 Series User’s Manual 0x3301 1 word 0x3302 1 word 0x3303 1 word 0x3304 1 word 0x3305 1 word 0x3500 1 word 0x3501 1 word Modbus/TCP Map TR 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding TR Coupling 0x0000:Off 0x0001:On 0xFFFF:Turbo Ring Not Enable TR Coupling Port status 0x0000:Port Disa
EDS-600 Series User’s Manual 0x3502 1 word 0x3600 1 word 0x3601 1 word 0x3602 1 word 0x3603 1 word 0x3680 1 word 0x3681 1 word 0x3682 1 word Modbus/TCP Map TR2 Coupling Port Backup status (Only using in Dual Homing) 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 status 0x0000:Healthy 0x0001:Break 0xFFFF:Turbo Ring V2 Not Enable TR2 Ring 1 Master/Slave 0x0000:Slave 0x0001:Master 0xFFFF:
EDS-600 Series User’s Manual 0x3683 1 word 0x3700 1 word 0x3701 1 word 0x3702 1 word Modbus/TCP Map TR2 Ring 2 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 2 Not Enable Turbo Chain Switch Role Mode 0x0000:Head Switch 0x0001:Member Switch 0x0002:Tail Switch 0xFFFF:Turbo Chain Not Enable Turbo Chain 1st Port Status 0x0000:Link Down 0x0001:Blocking 0x0002:Blocked 0x0003:Forwarding 0xFFFF:Turbo Chain
EDS-600 Series User’s Manual Modbus/TCP Map EDS-619 Modbus Information v1.
EDS-600 Series User’s Manual 0x005A 1 word 0x0080 1 word 0x0082 1 word 0x1000~0x1012 1 word 0x1100~0x1112 1 word 0x1200~0x1212 1 word 0x1300~0x1312 1 word 0x1400~0x1413(Port 1) 0x1414~0x1427(Port 2) 20 word 0x2000~0x2025 2 word 0x2100~0x2125 2 word Modbus/TCP Map Fault LED Status 0x0000:No 0x0001:Yes DI1 0x0000:Off 0x0001:On DO1 0x0000:Off 0x0001:On Port Information Port 1~19 Status 0x0000:Link down 0x0001:Link up 0x0002:Disable 0xFFFF:No port Port 1~19 Speed 0x0000:10M-Half 0x0001:10M-F
EDS-600 Series User’s Manual 0x2200~0x2225 2 word 0x2300~0x2325 2 word 0x3000 1 word 0x3100 1 word 0x3200~0x3212 1 word 0x3300 1 word 0x3301 1 word 0x3302 1 word 0x3303 1 word Modbus/TCP Map port 1~19 Tx Error Packets Ex: port 1 Tx Error Packets = 0x44332211 Word 0 = 4433 Word 1 = 2211 port 1~19 Rx Error Packets Ex: port 1 Rx Error Packets = 0x44332211 Word 0 = 4433 Word 1 = 2211 Redundancy Information Redundancy Protocol 0x0000:None 0x0001:RSTP 0x0002:Turbo Ring 0x0003:Turbo Ring V2 0x000
EDS-600 Series User’s Manual 0x3304 1 word 0x3305 1 word 0x3500 1 word 0x3501 1 word 0x3502 1 word 0x3600 1 word 0x3601 1 word Modbus/TCP Map TR Coupling Port status 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0005:Forwarding 0xFFFF:Turbo Ring Not Enable TR Coupling Control Port status 0x0000:Port Disabled 0x0001:Not Coupling Port 0x0002:Link Down 0x0003:Blocked 0x0005:Forwarding 0x0006:Inactive 0x0007:Active 0xFFFF:Turbo Ring Not Enable TR2 Coupling Mode 0x
EDS-600 Series User’s Manual 0x3602 1 word 0x3603 1 word 0x3680 1 word 0x3681 1 word 0x3682 1 word 0x3683 1 word 0x3700 1 word 0x3701 1 word Modbus/TCP Map TR2 Ring 1 1st Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not Enable TR2 Ring 1 2nd Port status 0x0000:Port Disabled 0x0001:Not Redundant 0x0002:Link Down 0x0003:Blocked 0x0004:Learning 0x0005:Forwarding 0xFFFF:Turbo Ring V2 Ring 1 Not
EDS-600 Series User’s Manual 0x3702 1 word Modbus/TCP Map Turbo Chain 2nd Port Status 0x0000:Link Down 0x0001:Blocking 0x0002:Blocked 0x0003:Forwarding 0xFFFF:Turbo Chain Not Enable Memory mapping from address 0x0000 ~ 0x3FFF.
