Home Station Fibra Óptica Freedom in a box.
This guide explains the installation process for the “Home Station Fibra Óptica”. Follow these guidelines step by step.
Connecting to the Internet 1. Connecting the Power Supply Plug the power supply into the mains and into the DC12v-1.67A connector on the “Home Station Fibra Óptica”. The rear panel of the “Home Station Fibra Óptica” contains the connectors and the switch shown in the figure below.
The side panels of the “Home Station Fibra Óptica” contain a USB port and three buttons labelled WPS, Reset and WIFI. The following table shows a description of the connectors and buttons shown above: Connector Description DC12V Power cable connector On/Off On/Off switch Reset Resets to the default configuration Eth.
2 Switching On the “Home Station Fibra Óptica” Switch on the “Home Station Fibra Óptica” by pressing the switch to the ON position. The table below explains the meaning of each of the LED indicators: Indicador luminoso Descripción Power On (fixed green): The router is switched on. Flashing (green/red): Initialisation process. Off: The router is not receiving power. On (fixed red): The router is restarting. Ethernet This light indicates whether there is any activity on the Eth.1 – Eth.2 - Eth.3 – Eth.
After switching on the router, you will see the following activity on the LED indicators: • The Power LED indicator will start flashing in red and green, indicating that the “Home Station Fibra Óptica” is initialising. Once the process is completed, the LED will indicate a constant green light. • The Internet LED will show the Internet connection status. When there is no Internet connection, the LED will be off.
Warning: Please do not switch off your device or disconnect it from the mains while this updating is being carried out: you may seriously damage the system. This process can take some 10 to 11 minutes after which your device will automatically restart. At this point the Power LED will flash in red and, once the process has successfully finished, then switch to a steady green.
You will need to configure the wireless client for your PC using these parameters. For more information, see the following page. 4.1.1 WPS Connection The “Home Station Fibra Óptica” is also compatible with the wireless connection secure exchange protocol WPS. It is important to take into account that, in order to use this wireless association method, the wireless client (the system used to connect to the “Home Station Fibra Óptica”) must be WPS-compatible.
4.2 Connecting via Cable Connect one end of one of the yellow Ethernet cables to the Ethernet card in your PC and connect the other end to one of the connectors on the “Home Station Fibra Óptica” labelled Eth 1-4. The other yellow Ethernet cable should connect the ONT to the WAN port of the “Home Station Fibra Óptica”. Switch on the PC. After a few seconds, the LAN LED for the connector to which the cable is connected will light up green.
Start Using your Optical Fiber... Congratulations! The installation of your “Home Station Fibra Óptica” is now complete! Open your browser, go to www.movistar.es and start surfing. If you cannot access the Internet, refer to the Troubleshooting section in this guide. Activate your e-mail accounts and your free web space included with your Internet access service. After opening www.movistar.es, select the option “Activar Correo” (Mail Activation).
Troubleshooting Problem Solution None of the LED indicators light up Check that the “Home Station Fibra Óptica” is connected to the mains and that the ON button is pressed. The Ethernet LED indicator does not light Verify that the LAN cable is connected at up both ends and that all the devices are switched on. The Wireless LED indicator does not light up Press the “WIFI” switch on the side panel to turn the unit on. 12 I cannot surf the Internet Check that the ONT has an Internet connection.
Problem Solution The wireless network keeps getting discon- If there are other active wireless networks nected in the same area, we recommend you configure the networks with a separation of 4 or 5 channels. If this is not possible, select the least saturated channel. Place your “Home Station Fibra Óptica” in a clear location. If you have network coverage problems, try changing the position of the aerial.
Remote Configuration Portal For more detailed information, and for configuration issues regarding your “Home Station Fibra Óptica”, visit: www.movistar.es/configuramirouter If you do not wish to use the router configuration portal, you may disable it and recover your management password for the “Home Station Fibra Óptica”.
Additional Information We would like to thank you for placing your Recycling trust in Movistar and purchasing one of our devices. For any clarification, question or Never dispose of your “Home Station Fibra complaint, please contact any of the fo- Óptica” with your household waste. llowing numbers free of charge: Consult your local authority regarding your • Personal Support Line (1004). options for appropriate and environmentally friendly disposal.
Customer Support The customer support service is available via telephone and Internet. For more information regarding Optical Fiber visit: www.movistar.es/router Movistar Technical Support Private customers: 1004 SMEs and professionals: 900 10 10 10 Customer support for executing the guarantee of the device Private customers: 1004 SMEs and professionals: 900 10 10 10 For more information, visit: www.movistar.
DECLARATION OF CONFORMITY According to the technical specifications applicable on the day as stated in Directive 99/05/CE of the European Parliament and Council dated 9th March 1999, adopted by Spanish legislation by Royal Decree 1890/2000 of 20th November 2000 and, specifically, according to: LVD 72/23 Directive modified by 93/68/CE and by the Electromagnetic Compatibility Directive 89/336/CE modified by Directive 92/31/CE Identification of the informant and the manufacturer Manufacturer: Teldat, S.A.
Glossary Antivirus: Dynamic/static addressing: Programmes designed for detecting and This defines the way in which Movistar assigremoving computer viruses and other mali- ns an IP address to your line. If your “Home cious programmes. Station Fibra Óptica” is assigned a different IP every time it starts a session, then you Ethernet cable: will have dynamic addressing, which is the Cable for transmitting data at high speed on default addressing method. If, on the other local networks (LAN).
PCMCIA: A hardware element generally used in laptop computers for expanding their capacity. The most common examples are wireless adaptors. WPS: Standard promoted by the Wi-Fi Alliance aimed at creating secure WLAN networks. WPS is not a security mechanism per se, but rather it involves the definition of several mechanisms to facilitate the configuration of a Ports: secure WLAN network with WEP, WPA and Physical or logical connections for sending WPA2, designed to minimise user intervenand receiving data.
More information: 1004 (from a mobile or land line) +34 699 991 004 (from abroad) Movistar shops www.movistar.es Version: 1.
