Polished Aluminium Dual Monitor Wall Mount Instruction Manual 75x75 100x100 32" (1.5~8kg)x2 (3.3~17.6lbs)x2 If you have any questions , please contact our customer service. TPM-MA05-114W-US1.
WARNING! If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help. Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
ASSEMBLY STEPS STEP 1: Attach Arm Assembly to Wall OPTION A: Wood Stud Installation A Position the Arm Assembly (A) at your desired height and line up the holes with your stud center line. Level the Arm Assembly (A) and mark the pilot hole locations. Locate your studs. Verify and mark 55mm (2.2") Drill pilot holes using a ø3/16 in. (ø4.5 mm) diameter drill bit. ø 4.
STEP 1: (Continued) OPTION B: Solid Concrete Wall Installation A Position the Arm Assembly (A) at your desired height , level the Arm Assembly (A) and mark the pilot hole locations. 60mm (2.4") ø10mm (ø 3/8") Drill pilot holes using a ø3/8 in. (ø10 mm) diameter drill bit. 60mm (2.4 ) W-B No! W-C W-A A Install Arm Assembly (A) using lag bolts (W-A), anchors (W-B) and washers (W-C). Tighten the lag bolts the Arm Assembly (A).
STEP 2: Attach Decorative Cover Attach Decorative Covers (D) to Lag Bolts (W-A).
STEP 3 : Attach Monitor OPTION A: Flat Back Monitor Attach the VESA plate (B) to back of monitor and secure with screws(M-A)or(M-C) with washers(M-E) using 6 mm Allen Key (E). Do not tighten the screws excessively or your monitor might be damaged. Monitor Monitor Monitor E M-A M-C B M-E No! OPTION B: Curved Back Monitor Monitor Monitor Monitor Attach the VESA plate (B) to back of monitor and secure with screws (M-B) or (M-D) with washers (M-E)and washers(M-F)using 6 mm Allen Key (E).
STEP 4: Hang Monitor Slide the monitor onto the head of swivel arm, install the security bolt (C). Make sure the security bolt is installed before you rotate the monitor. C Important Notice: The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly. Guideline to adjust monitor tilting angle.
STEP 5: Adjust Tension For intended functioning of the mount, you may need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (E). E CAUTION Note1: Be sure to keep the arm in horizontal position during adjustment. Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended. Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.
5: Cable (Continued) STEP 6: Management Attach Cable Cover For lower arm: Insert the cable and slide the cable cover down; For upper arm: Insert the cable and press the tabs on the inside of the cable cover slightly inward and slide down to reattach the cable cover.
Adjust as Desired Adjust monitor position and rotation. Tilt Swivel Rotation Height Swivel 180° +90° 360° Swivel 180° Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn't work out, please do not hesitate to ask for our help.
Product Dimensions 8.7" - 10.8" 2.4" 180° 2.9" 3.9" 4.5" 0.9" 2.9" 360° 5.9" 180° 3.9" 10 3.9" 4.5" +90° -45° 360° 11" 7.
CAUTION AND MAINTENANCE: • Never allow children to climb, stand, hang, or play on any part of monitor or stand. • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. • Check that the bracket is secure and safe to use at regular intervals (at least every three months).
