Mountain Buggy Carrycot Instruction Manual PAS SE D SA FE TY
This manual covers all carrycot attachments – single, double and twin options. Carrycots fit onto the following Mountain Buggy® models: English 1-10 Designed and made in New Zealand by Mountain Buggy Ltd. Manufactured by Tritec Manufacturing Ltd, an ISO 9001 certified company. Models made to BS 7409:1996, AS/NZS 2088:2000. Français 11-20 Conçu et fabriqué en Nouvelle-Zélande par Mountain Buggy Ltd. Fabriqué par Tritec Manufacturing Ltd, une société certifiée ISO 9001.
Welcome We know how precious and inspiring a new little person can be in your world. It’s so important to be able to show your baby to the world and just as important to show the world to your baby. At Mountain Buggy you and your baby matter to us. That’s why we have spent years researching and developing a product that is safe, comfortable and in tune with modern parents needs. We want you to be able to live your new family lifestyle with all the freedom and satisfaction you have always experienced.
2 For the sake of your precious passenger, please read these warnings before using your Mountain Buggy Carrycot. Important: Please read instructions carefully, follow them strictly and keep these instructions for future reference. Your child’s safety is your responsibility and may be compromised if you do not follow these instructions. Warning • Carrycot is suitable for newborns through to 6 months old, or until baby can sit up unaided.
Preparing your Stroller to fit the Carrycot Removing the Sunhood 1. 2. 3. Standing beside your stroller and using a reasonable degree of force, pull the sunhood support wire towards you (by about 50mm/2in). Remove support wire W from sunhood bush J on the side nearest to you. Unfasten sunhood domes that attach the sunhood to stroller frame and to stroller seat back. W J Removing the Seat 1. 2. 3. Unfasten domes on seat that attach to frame. Urban (Jungle) Only: unfasten strap underneath seat at point A.
4 ››› Preparing your Stroller (continued) IMPORTANT INFORMATION FOR DOUBLE AND TRIPLE STROLLERS If you have a double or triple stroller you will need to remove the centre metal bars of the frame to release the domed fabric. You may then need to reattach the metal bars without the fabric, depending on whether you are attaching a Double or a Twin Carrycot. See chart below. How to remove the centre bar(s) 1. 2. Terrain only: undo seat base nut with a spanner at point F and remove hinge pin from seat base.
Fitting your Carrycot to your Stroller Single Stroller Double Stroller Triple Stroller Double Carrycot Configuration 2 Configuration 2 Twin Carrycot Configuration 1 Configuration 2 Single Carrycot Configuration 1 Instructions for Configuration 1 are located on pages 6-7 Instructions for Configuration 2 are located on pages 8-10 Examples of Carrycot combinations Double Stroller with 2 Double Carrycots Double Stroller with Twin Carrycot Triple Stroller with 1 Double and 1 Twin Carrycot ENGLISH
6 ››› Configuration 1 Instructions PLEASE FOLLOW THESE INSTRUCTIONS IF YOU ARE FITTING: a: a Single Carrycot to a Single Stroller b: a Twin Carrycot to a Double Stroller Fitting the Snap Locks to the Carrycot PARTS LIST Preparation Carrycot You will need to have all components on the parts list shown to fit Carrycot to your stroller. Have a look at sides of Carrycot. There are three holes on each side of Carrycot to allow snap locks to be fitted.
Configuration 1 Instructions (continued) ENGLISH Fitting the Carrycot to the Frame 1. Ensure snap locks are rotated so screw holes are on top. Open snap locks. Place Carrycot onto Buggy frame. Confirm positioning as pictured below. 2. 3. TERRAIN ✘ ✔ URBAN X X Y Y sunhood joint Place snap lock X directly above sunhood joint 4. tube joint Place snap lock Y directly above tube joint Push snap locks firmly down flat, making sure you hear the lock ‘click’, indicating they are fully locked.
8 ››› Configuration 2 Instructions PLEASE FOLLOW THESE INSTRUCTIONS IF YOU ARE FITTING: a: a Double Carrycot to a Double Stroller b: a Double Carrycot to a Triple Stroller c: a Twin Carrycot to a Triple Stroller Fitting the Snap Locks and Slider Plate to the Carrycot Preparation PARTS LIST Make sure you have all the necessary parts as outlined in this picture.
9 Configuration 2 Instructions (continued) 5. 6. ENGLISH For Urban (Jungle) models URBAN Fit second snaplock to position B. Fit small screw and cover button to hole C. A C B For Terrain Models 5. 6. Fit second snap lock to position C. Fit small screw and cover button to hole B. TERRAIN C A B Fitting the Sliding Plate to the Carrycot • • Position sliding plate on opposite side of Carrycot to snap locks. Sliding plate screws are located at Holes A and C in side of Carrycot. Hole B is not required.
10 Configuration 2 Instructions (continued) Terrain • • Align Hole 1 of sliding plate with Hole A of Carrycot. Align Hole 2 of sliding plate with hole C of Carrycot. Place screws into Holes 1 and 2. Using Allen key, tighten in a clockwise direction. 1 TERRAIN 1 Warning: check that Carrycot attachment devices are correctly engaged before use. Fitting the Carrycot to the Frame 1. 2. 3. Ensure snap locks are rotated so screw holes are on top. Open snap locks.
INTERNATIONAL DISTRIBUTORS Australia Mountain Buggy Australia 223A East Boundary Road East Bentleigh, Victoria 3165, Australia Ph: (03) 9570 2833 Fax: (03) 9570 1362 Email: info@mountainbuggy.com.au www.mountainbuggy.com.au U.K. & Ireland Mountain Buggy (UK) Ltd Mill Farm, Fairmile, Ottery St Mary Devon EX11 1LS, England Ph: ++44 01 404 815 555 or 07000 4 BUGGY (07000 428 449) Fax: ++44 01 404 815 444 Email: info@mountainbuggy.co.uk www.mountainbuggy.co.
