WT4070/90 Wearable Terminal Integrator Guide
WT4070/90 Wearable Terminal Integrator Guide 72E-87638-06 Rev.
ii WT4070/90 Wearable Terminal Integrator Guide © 2007-9 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 9/29/06 Initial release. -02 Rev. A 03/28/07 Add 128 MB configuration, wall mounting bracket, Fusion 2.5 information. -03 Rev. A 05/06/08 Add BTExplorer support and freezer pouch information. -04 Rev. A 12/20/08 Add touch screen configuration. -05 Rev. A 03/03/09 Update Ethernet cradle daisychaining information. -06 Rev. A 12/15/09 Add Voice Only WT4090 information.
iv WT4070/90 Wearable Terminal Integrator Guide
Table of Contents Patents.................................................................................................................................................. ii Revision History .................................................................................................................................... iii About This Guide Introduction ...........................................................................................................................................
vi WT4070/90 Wearable Terminal Integrator Guide Changing the Power Settings ........................................................................................................ Changing the Display Backlight Settings ....................................................................................... Changing the Keypad Backlight Settings ....................................................................................... Turning the WLAN Radios Off ..............................................
Table of Contents MotoRC Software ........................................................................................................................... Microsoft ActiveSync Remote Display Software ............................................................................ Connection to Host Computer ............................................................................................................. MotoRC Connection ...........................................................................
viii WT4070/90 Wearable Terminal Integrator Guide Options ................................................................................................................................................ Operating Mode Filtering ............................................................................................................... Regulatory Options ........................................................................................................................ Band Selection ...............
Table of Contents ix Navigating the Favorites Window ............................................................................................ Delete all Favorite Services ........................................................................................................... Delete a Favorite Service ............................................................................................................... Rename a Favorite Service ...............................................................
x WT4070/90 Wearable Terminal Integrator Guide Flash Storage ...................................................................................................................................... FFS Partitions ................................................................................................................................ Working with FFS Partitions ........................................................................................................... RegMerge.dll .....................
Table of Contents Appendix A: Technical Specifications Technical Specifications ...................................................................................................................... Wearable Terminal ......................................................................................................................... RS309 Scanner .............................................................................................................................. RS409 Scanner .................
xii WT4070/90 Wearable Terminal Integrator Guide
About This Guide Introduction This guide provides information about setting up and configuring WT4070 and WT4090 wearable terminals and accessories. The WT4090 has two versions, one with a display and a voice only version without a display. Throughout this guide Voice Only WT4090 refers to the version without the display and WT4070/90 refer to the version with a display. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.
xiv WT4070/90 Wearable Terminal Integrator Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads WT4070 WLAN: 802.11b/g WPAN: Bluetooth 2.8” QVGA Color non-touch 128 MB RAM/ 64 MB Flash Optional accessory Windows CE 5.0 Professional Two-color or Triple-tap Alphanumeric Keypad WT4090 WLAN: 802.11a/b/g WPAN: Bluetooth 2.
About This Guide xv Fusion Software To determine the Fusion software version: 1. Press ALT - w. The Wireless menu appears. 2. Using the navigation keys, select Wireless Status. 3. Press ENTER. The Wireless Status window displays. 4. Press 5. The Versions screen appears.
xvi WT4070/90 Wearable Terminal Integrator Guide • Appendix A, Technical Specifications, includes a table listing the technical specifications for the wearable terminal and accessories. Notational Conventions The following conventions are used in this document: • “Wearable terminal” refers to the Motorola WT4070/90 series of wearable terminals.
About This Guide xvii • Enterprise Mobility Developer Kits, available at: http://www.motorola.com/enterprisemobility/support. • Device Configuration Package (DCP for WT4090c50) and Platform SDK (PSDK9090c50) for WT4090 with Windows CE 5.0, available at: http://www.motorola.com/enterprisemobility/support. • Latest ActiveSync software, available at: http://www.microsoft.com. For the latest version of this guide and all guides, go to: http://www.motorola.com/enterprisemobility/manuals.
xviii WT4070/90 Wearable Terminal Integrator Guide
Chapter 1 Getting Started Introduction This chapter lists the accessories for the wearable terminal and explains how to install and charge the batteries and start the wearable terminal for the first time. Unpacking the Wearable Terminal Carefully remove all protective material from around the wearable terminal and save the shipping container for later storage and shipping.
1-2 WT4070/90 Wearable Terminal Integrator Guide Power Button Display Charge Status LED Application Keypad Data Entry Keypad Speaker Action Keypad Figure 1-1 WT4070/90 Wearable Terminal Front View Application Controlled LED Battery Status LED WLAN Status LED Power Button Charge Status LED Action Keypad Figure 1-2 Voice Only WT4090 Wearable Terminal Front View Speaker
Getting Started 1-3 Interface Connector Rubber Plug Battery Battery Release Cleat Interface Connector (shown without Rubber Plug) Cradle Connector Figure 1-3 Wearable Terminal Back View Table 1-1 Parts of the Wearable Terminal Item Description Display Displays the application and data stored on the device. (WT470/090 only) Power Button Places the wearable terminal in to the suspend mode or resumes normal operation. Performs a warm boot when held down for five seconds.
1-4 WT4070/90 Wearable Terminal Integrator Guide Getting Started In order to start using the wearable terminal for the first time: • Install the main battery • Charge the main battery and backup battery • Start the wearable terminal. NOTE The main battery can be charged before or after installation into the wearable terminal.
Getting Started 1-5 Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 10-3. Charging the Main Battery and Memory Backup Battery Before using the wearable terminal for the first time, charge the main battery until the amber Charge Status LED remains lit (see Table 1-2 on page 1-5 for charge status indications).
1-6 WT4070/90 Wearable Terminal Integrator Guide Charging Spare Batteries Use the following accessories to charge spare batteries: • Single Slot USB cradle • Four Slot Spare Battery charger. To charge a spare battery: 1. Ensure the accessory used to charge the spare battery is connected to the appropriate power source. 2.
Getting Started 1-7 Starting the Wearable Terminal Press the Power button to turn on the wearable terminal. If the wearable terminal does not power on, perform a cold boot. See Performing a Cold Boot on page 1-8. NOTE When a battery is fully inserted in a wearable terminal for the first time, upon the wearable terminal’s first power up, the device boots and powers on automatically.
1-8 WT4070/90 Wearable Terminal Integrator Guide To save battery power, set the wearable terminal to turn off after a specified number of minutes. Configuring the Wearable Terminal • To customize the wearable terminal settings, refer to the Microsoft Applications for Mobile and CE 5.0 User Guide. • To set up ActiveSync to synchronize the wearable terminal with the host computer, see Chapter 3, ActiveSync.
Getting Started 1-9 • Set the wearable terminal to turn off after a short period of non-use. • Set the display and keypad backlight to turn off after a short period of non-use. • Turn on the keypad backlight only if needed. • Turn off all wireless radio activity when not in use. Changing the Power Settings NOTE To navigate using the keypad refer to the WT4070/90 Wearable Terminal User Guide. To set the wearable terminal to turn off after a short period of non-use: 1.
1 - 10 WT4070/90 Wearable Terminal Integrator Guide 1. Select Start > Settings > Control Panel > Keylight icon > Battery Power tab. 2. Press ENTER. 3. Select the On battery power: Disable keylight if not used for: check box and select a value from the drop-down list box. 4. Select the Advanced tab. 5. Select the Disable keylight check box to completely turn off the keypad backlight. 6. Press ENTER.
Chapter 2 Accessories Introduction Wearable terminal accessories provide a wide variety of product support capabilities. Accessories include cradles, a battery charger, scanners and headsets. For all accessories not covered in this chapter, refer to the WT4070/90 Wearable Terminal User Guide. Cradles • Single Slot USB cradle charges the wearable terminal main battery and a spare battery. It also synchronizes the wearable terminal with a host computer through a USB connection.
2-2 WT4070/90 Wearable Terminal Integrator Guide Single Slot USB Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 10-3. This section describes how to set up and use a Single Slot USB cradle with the wearable terminal. For USB communication setup procedures see Communication Setup on page 2-5. The Single Slot USB cradle: • Provides 5.4 VDC power for operating the wearable terminal.
Accessories USB A Male USB Port Power Port AC Line Cord USB Port Power Supply DC Cable Mini USB B USB Cable Figure 2-1 Single Slot USB Cradle Setup 2-3
2-4 WT4070/90 Wearable Terminal Integrator Guide Spare Battery Charge Status LED Figure 2-2 Wearable Terminal and Spare Battery Charging Battery Charging Indicators The Single Slot USB cradle can charge the wearable terminal’s main battery and a spare battery simultaneously. The wearable terminal’s amber Charge Status LED indicates the status of the battery charging in the wearable terminal. See Table 1-2 on page 1-5 for charging status indications.
Accessories 2-5 Communication Setup The wearable terminal can communicate with a host computer using the Single Slot USB cradle. By default the wearable terminal is configured to communicate using USB. Ensure that ActiveSync on the host computer is set to allow USB connections. 1. Ensure that ActiveSync was installed on the host computer and a partnership was created. 2. Start ActiveSync if it is not running on the host computer. To start, select Start > Programs > Microsoft ActiveSync.
2-6 WT4070/90 Wearable Terminal Integrator Guide Four Slot Ethernet Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 10-3. This section describes how to set up and use a Four Slot Ethernet cradle with the wearable terminal. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating up to four wearable terminals.
Accessories Ethernet Port 1 2-7 Power Port AC Line Cord Power Supply Ethernet Switch Connection Ethernet Cable DC Power Cable Figure 2-5 Four Slot Ethernet Cradle Setup Daisychaining Cradles To connect several cradles to an Ethernet network, up to four Ethernet cradles may be daisychained. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will certainly result.
2-8 WT4070/90 Wearable Terminal Integrator Guide Speed LED Link LED Ethernet Port 2 1st Cradle 2nd Cradle Ethernet Port 1 Ethernet Cable Figure 2-6 Daisychaining Four Slot Ethernet Cradles Ethernet Cradle Drivers The Ethernet cradle drivers are pre-installed on the wearable terminal and initiate automatically when the wearable terminal is placed in a properly connected Four Slot Ethernet cradle.
Accessories 1. Use the navigation keys to select Programs. 2. Press ENTER to open the sub-menu. 3. Use the navigation keys to select Command Prompt. 4. Press ENTER. The Command Prompt window displays. 5. Enter ipconfig. The window displays the IP Address assigned to the wearable terminal.
2 - 10 WT4070/90 Wearable Terminal Integrator Guide Battery Charging Indicators The wearable terminal’s amber Charge Status LED shows the status of the battery charging in the wearable terminal. See Table 1-2 on page 1-5 for charging status indications. The standard capacity battery usually charges in less than four hours and the extended capacity battery usually charges in less than eight hours. Speed LED The green Speed LED lights to indicate that the transfer rate is 100 Mbps.
Accessories 2 - 11 Four Slot Spare Battery Charger CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 10-3. This section describes how to set up and use the Four Slot Spare Battery Charger to charge up to four spare batteries. Figure 2-9 Four Slot Spare Battery Charger Setup CAUTION Use only a Motorola approved power supply output rated 12 VDC and minimum 3.3 A.
2 - 12 WT4070/90 Wearable Terminal Integrator Guide Battery Charging Indicators Each battery charging well has an amber Spare Battery Charge Status LED. (see Figure 2-10 on page 2-11). See Table 2-2 for charging status indications. The standard capacity battery usually charges in less than four hours and the extended capacity battery usually charges in less than eight hours.
Accessories 2 - 13 Wall Mount Bracket Use the wall mounting bracket to mount a Four Slot Ethernet cradle and a Four Slot Battery Charge together on a wall. To mark the screw holes for mounting the bracket use the wall mounting bracket as a template. Place the bracket onto the wall, level and mark the five screw hole locations. 1. Install top three screws into the wall. 2. Align the top three mounting holes with the screws. 3. Place mounting bracket on screws. 4.
2 - 14 WT4070/90 Wearable Terminal Integrator Guide Power Supply Installation Place power supply onto mounting shelf with the DC output connector and fan facing out and with the fan on top.
Accessories 2 - 15 Four Slot Ethernet Cradle Installation 1. Align the two slots in the back of the cradle with the two cradle alignment tabs on the bracket. Cradle Slots Cradle Alignment Tab Figure 2-13 Aligning the Slots in the Cradle with Mounting Bracket Tabs 2. Secure the cradle to the mounting bracket with two M4.0 screws supplied with the bracket.
2 - 16 WT4070/90 Wearable Terminal Integrator Guide Figure 2-14 Securing the Four-Slot Ethernet Cradle to the Mounting Bracket
Accessories 2 - 17 Four Slot Battery Charger Installation The Four Slot Spare Battery Charger has four mounting slots on the back. Around the slots are guides that assist in proper alignment of the charger onto the mounting bracket. Gravity holds the charger in place. Mounting Slots Mounting Studs Figure 2-15 Installing the Battery Charger onto the Mounting Bracket Position the charger over the mounting studs and slide the charger into place. Ensure that the charger is seated properly.
2 - 18 WT4070/90 Wearable Terminal Integrator Guide Cradle Power Plug Ethernet Cable Plug Right Cable Slot Charger Power Plug Tie-Wraps Figure 2-16 Cable Routing 10. Use one tie-wrap to secure the AC line cord and Ethernet cable to the mounting bracket. 11. Use two tie-wraps to secure the charger power lead, the AC line cord and Ethernet cable (if required) together as shown below. Charger Power Lead Tie-Wraps Ethernet Cable AC Line Cord Tie-Wrap Figure 2-17 Routing Cables 12.
Accessories 2 - 19 Placing a Battery in the Charger When placing a spare battery into the Four Slot Spare Battery Charger, ensure proper orientation of the battery. Figure 2-18 Inserting a Battery into the Battery Charger Mounting Multiple Brackets When installing multiple brackets on a wall: • Each mounting bracket must be 25.4 cm (10 in.) from the top of one bracket to the top of the next bracket. • The bottom of the last bracket must be at least 61 cm (24 in.) from the floor.
2 - 20 WT4070/90 Wearable Terminal Integrator Guide Position Tabs Together to Ensure Minimum Distance 25.4 cm 10 in. 61 cm 24 in.
Accessories 2 - 21 Navigating the Wearable Terminal with an External Input Device To assist in development, an external input device, such as a mouse, can be used to navigate the desktop and applications instead of using the wearable terminal keypad. • USB devices • mouse • keyboard • hub • Bluetooth mouse. USB Device NOTE The wearable terminal must be inserted into the Single Slot USB cradle to use a USB input device.
2 - 22 WT4070/90 Wearable Terminal Integrator Guide USB Keyboard Mini USB A USB A Female USB Cable Figure 2-21 USB Keyboard Connection to the Single Slot USB Cradle USB Keyboard USB Mouse Mini USB A USB Cable USB Hub USB A Female Figure 2-22 USB Mouse/Keyboard/Hub Connection to the Single Slot USB Cradle
Accessories 2 - 23 Bluetooth Mouse NOTE The following procedures assume that you are using the wearable terminal keypad. Use these procedures for OEM version 04.20.0004 and below. For OEM version 05.30.0000 and above, see Chapter 6, Using Bluetooth for more information on using the BTExplorer application. To setup a Bluetooth mouse: 1. If the Start Up window is not displayed, open the Start Up menu (OTL). 2. Press 5. 3. Press 3. The StackHID window displays. 4.
2 - 24 WT4070/90 Wearable Terminal Integrator Guide Connector Shroud Assembly 1. Remove cable from wearable terminal, if required. 2. Align the cable connector with the connector shroud bottom housing. Ensure that the disconnect button on the connector faces up. Disconnect Button Bottom Housing Figure 2-23 Installing Bottom Housing 3. Place the cable connector into the shroud bottom housing as shown. Figure 2-24 Installing Top Housing 4. Press the top housing into the bottom housing.
Accessories 2 - 25 Connector Eject Hole Figure 2-25 Disconnecting Connector with Shroud
2 - 26 WT4070/90 Wearable Terminal Integrator Guide
Chapter 3 ActiveSync Introduction To communicate with various host devices, install Microsoft ActiveSync (version 4.1 or higher) on the host computer. Use ActiveSync to synchronize information on the wearable terminal with information on the host computer. Changes made on the wearable terminal or host computer appear in both places after synchronization. ActiveSync software: • Allows working with wearable terminal-compatible host applications on the host computer.
3-2 WT4070/90 Wearable Terminal Integrator Guide Wearable Terminal Setup NOTE Microsoft recommends installing ActiveSync on the host computer before connecting the wearable terminal. The wearable terminal is set by default to communicate using a USB connection. Chapter 2, Accessories provides the accessory setup and cable connection information for use with the wearable terminal. The wearable terminal communication settings must be set to match the communication settings used with ActiveSync.
ActiveSync 3-3 Figure 3-2 Connection Settings Window 3. Select Allow USB connections check box. 4. Select the Show status icon in Taskbar check box. 5. Select OK to save any changes made. Setting up a Partnership To set up a partnership: 1. If the Get Connected window does not appear on the host computer, select Start > All Programs > Microsoft ActiveSync. Figure 3-3 New Partnership Window 2. Select if you want to synchronize with the host computer or to connect as a guest. 3. Click Next.
3-4 WT4070/90 Wearable Terminal Integrator Guide Figure 3-4 Select Synchronization Setting Window 4. Select the appropriate settings and click Next. Figure 3-5 Setup Complete Window 5. Click Finish.
ActiveSync 3-5 WT4090 Figure 3-6 ActiveSync Connected Window During the first synchronization, information stored on the wearable terminal is copied to the host computer. When the copy is complete and all data is synchronized, the wearable terminal can be disconnected from the host computer. NOTE The first ActiveSync operation must be performed with a local, direct connection. To retain partnerships after a cold boot, capture partnership registry information in a .
3-6 WT4070/90 Wearable Terminal Integrator Guide
Chapter 4 Voice Only WT4090 Remote Control Introduction Since the Voice Only WT4090 does not have a display, access to settings and controls must be done using a remote display software, such as MotoRC or ActiveSync Remote Display. MotoRC Software Download the MotoRC application from the Motorola Support Central web site: http://www.motorola.com/enterprisemobility/support. Follow the instructions provided with the software to install on a host computer.
4-2 WT4070/90 Wearable Terminal Integrator Guide MotoRC Connection To control the Voice Only WT4090 using the MotoRC software: 1. On the host computer, click Start > Programs > Motorola > MSP > MotoRC > Run Motorola Remote Control. The Run Motorola Remote Control DOS window opens followed by the Motorola Remote Control window. UI Control Icon Figure 4-1 Motorola Remote Control Window 2. Click on the UI Control icon to display the Voice Only WT4090 desktop.
ActiveSync Figure 4-2 Motorola Remote Control Window with Voice Only WT4090 Desktop 3. Use the host computer mouse to control the Voice Only WT4090 desktop. 4. When finished, close the Motorola Remote Control and Run Motorola Remote Control windows. Microsoft ActiveSync Remote Display Connection To control the Voice Only WT4090 using the Microsoft ActiveSync Remote Display software: 1. On the host computer, click Start > Programs > ActiveSync Remote Display.
4-4 WT4070/90 Wearable Terminal Integrator Guide
Chapter 5 Wireless Applications Introduction NOTE This chapter described Fusion versions below 2.55. For Fusion versions 2.55 and above, refer to the Wireless Fusion Enterprise Mobility Suite User Guide for Version X.XX User Guide for information, where X.XX represents the Fusion version number. These guides are available on the Motorola Support Central web site: http://www.motorola.com//enterprisemobility/manuals.
5-2 WT4070/90 Wearable Terminal Integrator Guide Figure 5-1 Wireless Applications Menu Signal Strength Icon The Signal Strength icon in the task tray indicates the wearable terminal’s wireless signal strength as follows: Table 5-1 Wireless Applications Icons, Signal Strength Descriptions Icon Status Action Excellent signal strength Wireless LAN network is ready to use. Very good signal strength Wireless LAN network is ready to use. Good signal strength Wireless LAN network is ready to use.
Wireless Applications 5-3 Turning the WLAN Radio On and Off To turn off the WLAN radio: 1. Press ALT - w. The Wireless menu appears. 2. Using the navigation keys, select Disable Radio. 3. Press ENTER. To turn on the radio: 1. Press ALT - w. The Wireless menu appears. 2. Using the navigation keys, select Enable Radio. 3. Press ENTER. Find WLANs Application Use the Find WLANs application to discover available networks in the vicinity of the user and wearable terminal.
5-4 WT4070/90 Wearable Terminal Integrator Guide Table 5-2 Signal Strength Icon Icon Description Excellent signal Very good signal Good signal Fair signal Poor signal Out of range or no signal Table 5-3 Encryption Icon Icon Description No encryption. WLAN is an infrastructure network. WLAN is an Ad-Hoc network. WLAN access is encrypted and requires a password. Select a WLAN network in the list using the navigation keys.
Wireless Applications 5-5 Figure 5-3 Profile ID Dialog Box Table 5-4 Profile ID Fields Field Description Name The name and (WLAN) identifier of the network connection. Enter a user friendly name for the wearable terminal profile used to connect to either an AP or another networked computer. Example: The Public LAN. ESSID The ESSID is the 802.11 extended service set identifier.
5-6 WT4070/90 Wearable Terminal Integrator Guide Table 5-5 Operating Mode Fields Field Description Operating Mode Select Infrastructure to enable the wearable terminal to transmit and receive data with an AP. Infrastructure is the default mode. Select Ad Hoc to enable the wearable terminal to form its own local network where wearable terminals communicate peer-to-peer without APs using a shared ESSID. Country Country determines if the profile is valid for the country of operation.
Wireless Applications 5-7 Ad-Hoc Use the Ad-Hoc dialog box to select the required information to control Ad-Hoc mode. This dialog box does not appear if you selected Infrastructure mode. To select Ad-Hoc mode: 1. Press Tab to highlight the Channel drop-down list. 2. Use the navigation keys to select a channel number. The default is Channel 1 (2412 MHz). Figure 5-5 Ad-Hoc Settings Dialog Box 3. Press TAB twice to highlight the Next button. 4. Press ENTER. The Encryption dialog box displays.
5-8 WT4070/90 Wearable Terminal Integrator Guide Figure 5-6 Authentication Dialog Box Table 5-6 Authentication Options Authentication Description None Default setting when authentication is not required on the network. TLS (Fusion 2.4) EAP-TLS (Fusion 2.5) Select this option to enable EAP-TLS authentication. EAP-TLS is an authentication scheme through IEEE 802.1x. It authenticates users and ensures only valid users can connect to the network.
Wireless Applications 5. Press ENTER. The Installed User Certificates dialog box appears. Table 5-7 lists the PEAP tunneled authentication options.
5 - 10 WT4070/90 Wearable Terminal Integrator Guide Table 5-8 TTLS Tunneled Authentication Options (Continued) TTLS Tunneled Authentication Description MS CHAP v2 MS CHAP v2 is a password based, challenge response, mutual authentication protocol that uses the industry standard Message Digest 4 (MD4) and Data Encryption Standard (DES) algorithms to encrypt responses. The authenticating server challenges the access client and the access client challenges the authenticating server.
Wireless Applications 5 - 11 ********* Figure 5-9 Credentials Dialog Box 3. Enter the User:, Pwd: (password), and Server: information in their respective text boxes. Press TAB to move to each field. 4. Press TAB to highlight the Retrieve button. 5. Press ENTER. A Progress dialog indicates the status of the certificate retrieval. 6. Press ENTER exit. After the installation completes, the Installed User Certs dialog box displays and the certificate is available in the drop-down list for selection.
5 - 12 WT4070/90 Wearable Terminal Integrator Guide Figure 5-11 Browse Server Certificates a. 3. Navigate to the folder where the certificate is stored. Select the certificate filename and then select ok. A confirmation dialog verifies the installation. If the information in this dialog is correct, select the Yes button, If the information in this dialog is not correct select the No button. The wizard returns to the Installed Server Certs dialog box.
Wireless Applications 5 - 13 caching options require the wearable terminal to prompt for new credentials. If you entered the credentials via the profile, the wearable terminal does not prompt for new credentials. Table 4-9 lists the caching options. Table 5-9 Cache Options Description At Connect Select this option to prompt for credentials whenever the wearable terminal tries to connect to a new profile. Deselect this to use the cached credentials to authenticate.
5 - 14 WT4070/90 Wearable Terminal Integrator Guide Figure 5-15 At Time Dialog Box 6. Enter the time using the 24 hour clock format in the (hh:mm) box. 7. Press TAB to highlight the > button. 8. Press ENTER. to move the time to the right text box. Repeat for additional time periods. 9. Press TAB to highlight the Next button. The User Name dialog box displays. User Name The user name and password can be entered (but is not required) when the profile is created.
Wireless Applications 5 - 15 Figure 5-17 Password Dialog Box 1. Enter a password in the Password field. 2. Press TAB to highlight the Advanced ID check box. 3. Press ALT > BKSP (SPACE) to select the Advanced ID check box, if advanced identification is required. 4. Press TAB twice to highlight the Next button. 5. Press ENTER. The Encryption dialog box displays. See Encryption on page 4-17. Advanced Identity Use the Advanced ID dialog box to enter the 802.1X identity to supply to the authenticator.
5 - 16 WT4070/90 Wearable Terminal Integrator Guide 2. Press TAB. 3. Use the navigation keys to select a key index number. 4. Press TAB. 5. Press ALT > BKSP (SPACE) to select the Use Passkey check box. 6. Press TAB twice to highlight the Next button. 7. Press ENTER. Figure 5-19 Encryption Dialog Box Table 5-10 Encryption Options Encryption Description Open Select Open (the default) when no data packet encryption is needed over the network.
Wireless Applications 5 - 17 Table 5-11 Encryption / Authentication Matrix Encryption Authentication Open WEP TKIP AES (Fusion 2.5 only) None Yes Yes Yes Yes EAP TLS No Yes Yes Yes PEAP No Yes Yes Yes LEAP No Yes Yes Yes TTLS No Yes Yes Yes Key Entry Page If you select either 40-Bit WEP or 128-Bit WEP the wizard proceeds to the key entry dialog box unless the Use Passkey check box was selected in the Encryption dialog box (see Figure 4-21 on page 4-17).
5 - 18 WT4070/90 Wearable Terminal Integrator Guide Figure 5-21 Passkey Dialog Box 1. Enter the passkey in the Passkey text box. 2. Press TAB twice to highlight the Next button. 3. Press ENTER. The IP Address Entry dialog box displays. IP Address Entry Use the IP Address Entry dialog box to configure network address parameters: IP address, subnet, gateway, DNS, and WINS.
Wireless Applications 5 - 19 Figure 5-23 Static IP Address Entry Dialog Box 1. Enter the IP address in the IP Address text box. 2. Press TAB. 3. Enter the subnet mask address in the Subnet Mask text box. Table 5-13 Static IP Address Entry Fields Field Description IP Address The Internet is a collection of networks with users that communicate with each other.
5 - 20 WT4070/90 Wearable Terminal Integrator Guide Table 5-14 IP Config Advanced Address Entry Fields Field Description G/W The default gateway forwards IP packets to and from a remote destination. DNS The Domain Name System (DNS) is a distributed Internet directory service. DNS translates domain names and IP addresses, and controls Internet email delivery. Most Internet services require DNS to operate properly. If DNS is not configured, Web sites cannot be located and/or email delivery fails.
Wireless Applications 5 - 21 Figure 5-26 Transmit Power Dialog Box (Ad-Hoc Mode) Table 5-16 Power Transmit Options (Ad-Hoc Mode) Field Description Full Select Full power for the highest transmission power level. Select Full power when operating in highly reflective environments and areas where other devices could be operating nearby, or when attempting to communicate with devices at the outer edge of a coverage area. 30 mW Select 30 mW to set the transmit power level to 30 mW.
5 - 22 WT4070/90 Wearable Terminal Integrator Guide Table 5-17 Battery Usage Options Field Description CAM Continuous Aware Mode (CAM) provides the best network performance, but yields the shortest battery life. Fast Power Save Fast Power Save (the default) performs in the middle of CAM and MAX Power Save with respect to network performance and battery life. MAX Power Save Max Power Save yields the longest battery life while potentially reducing network performance.
Wireless Applications 5 - 23 Table 5-18 Profile Icons (Continued) Icon Description Profile is in use and describes an ad-hoc profile not using encryption. Profile is in use and describes an ad-hoc profile using encryption. Profile is not valid in the device current operating regulatory domain. The profiles are listed in priority order for use by the automatic roaming feature. Change the order by moving profiles up or down.
5 - 24 WT4070/90 Wearable Terminal Integrator Guide profile. Use the Profile Wizard to edit the profile power consumption and security parameters. See Profile Editor Wizard on page 4-6. Creating a New Profile To create new profiles from the Manage Profiles window, press Blue key - TAB (Menu). Figure 5-31 Manage Profiles - Add Select Add and press ENTER to display the Profile Wizard wherein you can set the profile name and ESSID.
Wireless Applications 5 - 25 If required, change the name in the Name field and select Save. A confirmation dialog box appears after the export completes. Wireless Status Application To open the Wireless Status window, press ALT - w, select Wireless Status and press ENTER. The Wireless Status window displays information about the wireless connection. Figure 5-33 Wireless Status Window The Wireless Status window contains the following options. Select the option to display the option window.
5 - 26 WT4070/90 Wearable Terminal Integrator Guide Figure 5-34 Signal Strength Window After viewing the Signal Strength window, press ESC to return to the Wireless Status window. Table 5-19 Signal Strength Status Field Signal Description Displays the Relative Signal Strength Indicator (RSSI) of the signal transmitted between the AP and wearable terminal. As long as the Signal Quality icon is green the AP association is not jeopardized.
Wireless Applications 5 - 27 Table 5-19 Signal Strength Status (Continued) Field Description Association Count Displays the number of APs the wearable terminal connects to while roaming. AP MAC Address Displays the MAC address of the AP to which the wearable terminal is connected. Transmit Rate Displays the current rate of the data transmission. Current Profile Window The Current Profile window displays basic information about the current profile and connection settings.
5 - 28 WT4070/90 Wearable Terminal Integrator Guide To open the IPv4 Status window, press 3. Figure 5-36 IPv4 Status Window Table 5-21 IPv4 Status Fields Field Description IP Type Displays the IP type for the current profile: DHCP or Static. If the IP type is DHCP, leased IP address and network address data appear for the wearable terminal. If the IP type is Static, the values displayed were input manually in the IP Config tab on page 4-19. IP Address Displays the wearable terminal’s IP address.
Wireless Applications 5 - 29 Wireless Log Window The Wireless Log window displays a log of recent activity, such as authentication, association, and DHCP renewal completion, in time order. Save the log to a file or clear the log (within this instance of the application only). The auto-scroll feature automatically scrolls down when new items are added to the log. To open the Wireless Log window, press 4. The Wireless Log window displays.
5 - 30 WT4070/90 Wearable Terminal Integrator Guide Figure 5-38 Versions Window The window displays software version numbers for the following: • Configuration Editor (Fusion 2.4 only) • Fusion Build • Public API • LoginService • Photon10 • WCCConfigEd (Fusion 2.5 only) • WCDiag • WCLaunch • WCSAPI • WCSRV • WCStatus. Press ESC to return to the Wireless Status window.
Wireless Applications 5 - 31 • ICMP Ping - tests the wireless network connection. • Trace Route - tests a connection at the network layer between the wearable terminal and any place on the network. • Known APs - displays the APs in range using the same ESSID as the wearable terminal. • Quit - Exits the Wireless Diagnostics window. To return to the Wireless Diagnostics window from an option window, press ESC.
5 - 32 WT4070/90 Wearable Terminal Integrator Guide Figure 5-41 Trace Route Window Enter an IP address or a DNS Name in the IP combo box. Press TAB to highlight Start Test. Press Blue - BKSP. The IP combo box should match the information shown in the ICMP Ping window’s IP combo box. When starting a test, the trace route attempts to find all routers between the wearable terminal and the destination.
Wireless Applications 5 - 33 • The wearable terminal roams to a new profile • The wearable terminal suspends • The wearable terminal resets (warm or cold). Select Set Roaming to allow the wearable terminal to roam to any AP with a better signal. These settings are temporary and never saved to the registry. Select Refresh to update the list of the APs with the same ESSID. The highest signal strength value is 32.
5 - 34 WT4070/90 Wearable Terminal Integrator Guide The AP Networks and Ad-Hoc Networks check boxes are selected by default. To select/de-select the checkboxes, press TAB to highlight a checkbox. Press Blue - BKSP to select or de-select the checkbox. Table 5-23 OP Mode Filtering Options Field Description AP Networks Select the AP Networks check box to display available AP networks and their signal strength within the Available WLAN Networks (see Find WLANs Application on page 4-5).
Wireless Applications 5 - 35 Band Selection The Band Selection settings identify the frequency bands to scan when finding WLANs. These values refer to the 802.11 standard networks. NOTE Select one band for faster access when scanning for WLANs. Figure 5-45 Band Selection Dialog Box Table 5-25 Band Selection Options Field Description 2.4GHz Band The Find WLANs application list includes all networks found in the 2.4 GHz band (802.11b and 802.11g).
5 - 36 WT4070/90 Wearable Terminal Integrator Guide Table 5-26 System Options Field Description Profile Roaming Configures the wearable terminal to roam to the next available WLAN profile when it moves out of range of the current WLAN profile. Enable IP Mgmt Enables the Wireless Companion Services to handle IP address management. The Wireless Companion Service configures the IP based on what is configured in the network profile.
Wireless Applications 5 - 37 Export NOTE Exporting options enables settings to persists after cold boot. Use Export to export all profiles to a registry file, and to export the options to a registry file. Figure 5-48 Options - Export Dialog Box To export options: 1. Select Export Options and press Blue - BKSP. The Save As dialog box displays. Figure 5-49 Export Options Save As Dialog Box 2. Enter a filename in the Name: field. The default filename is WCS_OPTIONS.REG. 3.
5 - 38 WT4070/90 Wearable Terminal Integrator Guide Selecting Export All Profiles saves the current profile. This information is used to determine which profile to connect with after a warm boot or cold boot. Persistence Export options and profiles to provide cold boot persistence for Windows CE 5.0 devices. Save the exported registry files in the Application folder to use them on a cold boot or clean boot and restore previous profile and option settings.
Wireless Applications 5 - 39 Log On/Off Application When the user launches the Log On/Off application, the wearable terminal may be in two states; the user may be logged onto the wearable terminal by already entering credentials through the login box, or there are no user logged on. Each of these states have a separate set of use cases and a different look to the dialog box.
5 - 40 WT4070/90 Wearable Terminal Integrator Guide Table 5-28 Log On/Off Options (Continued) Field Description Network Username and Password Fields The Network Username and Network Password fields are used as credentials for the profile selected in the Wireless Profile field. Currently these fields are limited to 159 characters. Mask Password Checkbox The Mask Password checkbox determines whether the password field is masked (i.e., displays only the '*' character) or unmasked (i.e.
Chapter 6 Using Bluetooth Introduction NOTE The VOWT4090 requires the use of a Remote Desktop software to configure settings and software. See for information on setting up the device with remote desktop software. Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) RF to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1).
6-2 WT4070/90 Wearable Terminal Integrator Guide When AFH is enabled, the Bluetooth radio “hops-around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows Symbol wearable terminals to operate in any infrastructure. AFH is always enabled in the WT4090. The Bluetooth radio in this wearable terminal operates as a Class 2 device power class. The maximum output power is 2.5mW and the expected range is up to 32.8 feet (10 meters).
Using Bluetooth 6-3 Turning the Bluetooth Radio Mode On and Off NOTE Turning the Bluetooth radio on and off using the following procedures is only available on OEM version 05.30.0000 and higher. Earlier OEM versions use StoneStreet API commands to turn the Bluetooth radio on and off. See the SDMDK Help File for more information. Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane).
6-4 WT4070/90 Wearable Terminal Integrator Guide Bluetooth Power States Cold Boot When a cold boot is performed on the wearable terminal, Bluetooth turns off. It is normal to see the Bluetooth icon appear and disappear, as well as a wait cursor, when initialization proceeds in all modes. Warm Boot When a warm boot is performed on the wearable terminal, Bluetooth returns to the disabled state (off). Suspend When the wearable terminal suspends, Bluetooth turns off.
Using Bluetooth 5. 6-5 The ProfileSelector window appears. Figure 6-3 Bluetooth Profile Selector Window NOTE 6. The Serial Port profile is always active and cannot be removed. Use the navigation keys to highlight a profile. Press the SPACE key to select the profile. or press TAB to place focus on the Select All button to select all profiles or the Deselect All button to deselect all profiles. 7. Press TAB to place focus on the Apply button. 8. Press Space or ENTER to apply any changes. 9.
6-6 WT4070/90 Wearable Terminal Integrator Guide Accessing BTExplorer NOTE BTExplorer is only available on OEM version 05.30.0000 and higher. The BTExplorer application can be accessed from the App Launcher menu or by a key combination. Using App Launcher In the App Launcher main menu, press 5 to select 5 - Utilities. Press 3 to select BT Explorer. Figure 6-4 App Launcher Screens Using Key Combination Press ALT - B. Use the navigation keys to select Show BTExplorer.
Using Bluetooth 6-7 Table 6-2 Key Combinations Action Combination Access the Start menu on the taskbar CTRL - ESC Switch fields within an application TAB Close windows or cancel operations on some applications ESC or ALT - F4 Access the Task Manager ALT - TAB Switches to the next window or desktop ALT - ESC Access a menu bar in an application ALT - ALT Press a button or select a check box in an application TAB until the item is highlighted then SPACE.
6-8 WT4070/90 Wearable Terminal Integrator Guide Figure 6-5 New Connection Wizard Window 7. Use the navigation keys to select Explore Services on Remote Device.
Using Bluetooth NOTE 6-9 To filter devices in the list press ALT - F to open the filter menu. Select a device type and then press ENTER. To change the display view press ALT - V to open the view menu. Select a view type and then press ENTER. Figure 6-7 Select Remote Device Window 9. Use the navigation keys to select a device from the list and press ENTER. The wearable terminal searches for services on the selected Bluetooth device. Figure 6-8 Device Services 10.
6 - 10 WT4070/90 Wearable Terminal Integrator Guide Figure 6-10 Connection Summary Window 13. Press P2 to add the service to the Favorite window. 14. The Favorite window appears and the wearable terminal connects to the remote device. Figure 6-11 Favorite Window with Active Connection Available Services Some examples of available services are: • File Transfer Services • Headset Services • OBEX Object Push Services • Serial Port Services • Personal Area Network Services • HID Services.
Using Bluetooth 6 - 11 3. Press ENTER. The File Transfer window appears listing the folders of the remote device. Figure 6-12 File Transfer Window 4. Use the navigation keys to select a file. To open a folder press ENTER. 5. Press ENTER to copy the file from the remote device. The Save Remote Device window appears. Figure 6-13 Save Remote File Window 6. Press TAB three times to enter the folder area. 7. Use the navigation keys to select a folder to place the file into. 8. Press ENTER. 9.
6 - 12 WT4070/90 Wearable Terminal Integrator Guide 3. Press the right arrow to open the sub-menu. 4. Use the navigation keys to select Folder or File. 5. Press ENTER. The Create New Folder or Create New File window appears. Figure 6-14 Create New Folder Window 6. Enter a new name for the new folder or file and then press ENTER. 7. A new folder or file is created on the remote device. Delete File To delete a file from the remote device: 1. Use the navigation keys to select the file to delete.
Using Bluetooth 6 - 13 4. Press TAB three times to enter the folder area. 5. Using the navigation keys to highlight a folder and press ENTER. The OBEX Object Push window appears. 6. Press ENTER. The file is transferred from the remote device to the wearable terminal. Put File To copy a file from the wearable terminal to a remote device: 1. In the File Transfer window, navigate to a folder where the file will be put into. 2. Press MENU to open the pop-up menu. 3.
6 - 14 WT4070/90 Wearable Terminal Integrator Guide 3. Press ENTER. 4. The wearable terminal connects with the Access Point. 5. Press CTRL - ESC to open the Start menu. 6. Use the navigation keys to select Internet Explorer. 7. Press ENTER. The Internet Explorer window appears. 8. In the address field, enter an internet address and tap the Enter button. The web page loads. OBEX Object Push Services Object Exchange (OBEX) is a set of protocols allowing pictures to be shared using Bluetooth.
Using Bluetooth 6 - 15 9. Press ENTER. The wearable terminal connects to the remote device and begins to send the file. The Sending Picture window appears. When the file transfer is complete a confirmation dialog appears. Press ENTER. Figure 6-20 Sending Picture Window Headset Services To connect to a Bluetooth headset: 1. In the Favorite window, use the navigation keys to select the headset service. 2. Press MENU and select Connect from the pop-up menu. 3. Press ENTER. 4.
6 - 16 WT4070/90 Wearable Terminal Integrator Guide Figure 6-21 Remote Service Connection Window 5. In the Local COM Port drop-down list select a COM port. 6. Press ENTER. Personal Area Network Services Connect two or more Bluetooth devices to share files and collaborate. To establish a Personal Area Network connection: 1. In the Favorite window, use the navigation keys to select the Personal Area Network service. 2. Press MENU and select Connect from the pop-up menu. 3.
Using Bluetooth 6 - 17 Bonding with Discovered Device(s) A bond is a relationship created between the wearable terminal and another Bluetooth device in order to exchange information in a secure manner. Creating a bond involves entering the same PIN on the two devices to bond. Once a bond is created, and the Bluetooth radios are turned on, the devices recognize the bond and are able to exchange information without re-entering a PIN.
6 - 18 WT4070/90 Wearable Terminal Integrator Guide NOTE To filter devices in the list press ALT - F to open the filter menu. Select a device type and then press ENTER. To change the display view press ALT - V to open the view menu. Select a view type and then press ENTER. 6. Use the arrow keys to select a device from the list and press ENTER. The PIN Code Request window appears. Figure 6-24 Connection Favorite Options Window 7. In the PIN Code field, enter the PIN code. 8. Press ENTER.
Using Bluetooth 6 - 19 Figure 6-26 PIN Code Request Window NOTE Connections to untrusted devices are a security risk. 3. In the PIN Code: text box, enter the same PIN that was entered on the device requesting the bond. The PIN must be between 1 and 16 characters. 4. Press ENTER. The bond is created and the wearable terminal can now exchange information with the other device. Trusted Devices Window The Trusted Devices window lists all bonded devices. To access the Trusted Devices window: 1.
6 - 20 WT4070/90 Wearable Terminal Integrator Guide Figure 6-28 Trusted devices Window Menu Use the navigation keys to select a view type and then press ENTER. Deleting a Bonded Device If it is no longer necessary to connect with a device, delete it from the Bluetooth Trusted Devices window. 1. Use the navigation keys to select a device. 2. Press MENU. 3. Use the navigation keys to select Delete Link Key. 4. Press ENTER. A confirmation dialog box appears. 5.
Using Bluetooth 6 - 21 2. Press MENU. 3. Use the navigation keys to select Disconnect. 4. Press ENTER. A deaconate confirmation dialog box appears. 5. Select Yes to disconnect the service. The wearable computer disconnects from the service. Navigating the Favorites Window The Favorites window has three menus that can be accessed through key combinations. Figure 6-30 Favorites Window Menus To open the File menu, press ALT - F. To open the View menu, press ALT - V.
6 - 22 WT4070/90 Wearable Terminal Integrator Guide Rename a Favorite Service To rename a favorite: 1. Use the navigation keys to select a favorite. 2. Press MENU. 3. Use the down arrow key to select Rename. 4. Press ENTER. The Change Device Name window appears. 5. Enter a new name. 6. Press ENTER to change the name or ESC to cancel the name change. Change the Display View To change the display view: 1. Press ALT - V. 2. Use the down arrow key to select Large Icons, List or Details. 3.
Using Bluetooth 6 - 23 Bluetooth Settings Use the BTExplorer Settings window to configure the operation of the BTExplorer application. To access the settings, press ALT - T, use the navigation keys to select Settings. Press ENTER. The BTExplorer Settings window appears. Use the left and right arrows to move from one tab to the next. Within a tab, use the TAB key to move from one field to the next. Device Info Tab Use the Device Info tab to configure the wearable terminal’s Bluetooth connection modes.
6 - 24 WT4070/90 Wearable Terminal Integrator Guide Figure 6-32 BTExplorer Settings - Services Tab To add a service: 1. Press TAB to highlight the Add key. Press SPACE. The Add Local Service window displays. Figure 6-33 Add Local Service Window 2. In the list, use the navigation key to select a service to add. 3. Press ENTER to accept the service. Press ESC to exit without saving. The Edit Local Service window displays for the selected service. 4.
Using Bluetooth 6 - 25 Table 6-4 File Transfer Information Window Field Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list; None, Authenticate or Authenticate/Encrypt. Root Directory Select the directory that other Bluetooth devices can access. File Permissions Select the file permissions for the selected directory. Check the appropriate box to grant Read access, write access and delete access.
6 - 26 WT4070/90 Wearable Terminal Integrator Guide Figure 6-36 Personal Area Networking Window Table 6-6 Personal Area Networking Window Field Description Service Name Displays the name of the service. Service Security Select the type of security from the drop-down list; None, Authenticate or Authenticate/Encrypt. Support Group Ad-Hoc Networking Select to enable Ad-Hoc networking. Serial Port Service Serial port allows COM ports to be accessed by other Bluetooth devices.
Using Bluetooth 6 - 27 Table 6-7 Serial Port Service Window Field Description Local COM Port Select the COM port. Select COM1 to use a modem or other device that is connected to the connector on the bottom of the wearable terminal. Local Baud Rate Select the communication baud rate. Local Port Options Select the port option. Headset Service Headset service allows connection to a Bluetooth headset.
6 - 28 WT4070/90 Wearable Terminal Integrator Guide Security Tab To adjust the security settings for an individual service, select the Services tab first, then select the individual service, then Properties. Figure 6-40 BTExplorer Settings - Security Tab Table 6-8 Security Tab Field Description Use PIN Code (Incoming Connecting) Select for automatic use of the PIN code entered in the PIN Code text box. It is recommended not to use this automatic PIN code feature.
Using Bluetooth 6 - 29 Figure 6-41 BTExplorer Settings - Discovery Tab Table 6-9 Discovery Tab Field Description Inquiry Length Sets the amount of time that the wearable terminal takes to discover Bluetooth devices in the area. Name Discovery Mode Select either Automatic or manual. Discovered Devices buttons Deletes all discovered devices and link keys. Virtual COM Port Tab Use the Virtual COM Port tab to select the COM ports for Bluetooth communication.
6 - 30 WT4070/90 Wearable Terminal Integrator Guide Figure 6-43 COM Port Connection HID Tab NOTE The HID tab only appears if HID is selected in the Bluetooth Profile Selector application. See Bluetooth Profiles on page 6-4 for more information. Use the HID tab to set key repeat settings. Figure 6-44 BTExplorer Settings - HID Tab Table 6-11 HID Tab Field Description Enable Key Repeat Enable the Delay and Rate settings.
Using Bluetooth 6 - 31 Table 6-12 Miscellaneous Tab Field Description Highlight Connections Select the connection type to highlight when connected. In the Wizard Mode, the only option is Favorites or None. Apply Text Style Select the text style to be applied to the connection text. Apply Text Color Select the text color to be applied to the connection text.
6 - 32 WT4070/90 Wearable Terminal Integrator Guide
Chapter 7 Application Deployment Software Installation on Development PC To develop applications to run on the wearable terminal, use one or all of the following: • Enterprise Mobility Developer Kit (EMDK) for C • Windows CE Platform SDK for WT40x0 • Device Configuration Package (DCP) for WT40x0. The EMDK for C is a development tool used to create native C and C++ applications for the WT4070/90. It includes documentation, header files (.H), and library files (.
7-2 WT4070/90 Wearable Terminal Integrator Guide 3. Once installed, access the major components of the DCP from the Symbol Device Configuration Package (DCP) for WT40x0 program group of the Windows Start Menu. Platform SDK Different Platform SDKs are required for the Microsoft® Windows CE 5.0 Professional and Microsoft® Windows CE 5.0 Core platforms. To download and install the appropriate Platform SDK: 1. 2. Download the appropriate Platform SDK from the Support Central web site, http://www.motorola.
Application Deployment 7-3 OSUpdate The wearable terminal contains tools that update all operating system components. All updates are distributed as packages and/or hex images. Update packages can contain either partial or complete updates for the operating system. Motorola distributes the update packages on the Support Central Web Site, http://www.motorola.com/enterprisemobility/support. Update an operating system component using one of the following: • MSP.
7-4 WT4070/90 Wearable Terminal Integrator Guide Figure 7-1 ActiveSync Explorer 4. Double-click the folder to expand the contents of the folder. Figure 7-2 My Pocket PC Contents 5. Use Explorer to locate the host computer directory that contains the file to download. Tap that directory in the left pane to display its contents in the right pane. 6. Drag the desired file(s) from the host computer to the desired mobile device folder.
Application Deployment 7-5 previous file are erased. The operating system must be running for a file to be updated, so the IPL cannot perform individual file updates as it is a stand-alone program that does not require the operating system to be running. A typical partition is a group of files, combined into a single “partition” that represents a specific area of storage. Examples of partitions are the flash file systems such as Platform or Application.
7-6 WT4070/90 Wearable Terminal Integrator Guide • Creating the script for the hex image • Building the image • Sending the hex image • Creating a splash screen • Flash storage. Starting Terminal Configuration Manager Click the Windows start menu TCM icon (Symbol Device Configuration Packages, WT40x0c50) to start TCM. The TCM window appears displaying two child windows: Script1 and File Explorer.
Application Deployment 7-7 Table 7-1 TCM Components (Continued) Icon Component Function Save button Save the current script file. Large icons button View the current script items as large icon. Small icons button View the current script items as small icon. List button View the current script items as a list. Details button View the current script items with more details. About button Display version information for TCM. Properties button View/change the current script properties.
7-8 WT4070/90 Wearable Terminal Integrator Guide Figure 7-4 Script Properties Window - Partition Data Tab 3. In the Terminal drop-down list, select the terminal type. 4. Use the default Flash Type. 5. In the Disks drop-down list, select the number of disk partitions to create. 6. Select the (memory) Size for each partition. Note that adding space to one disk. partition subtracts it from another. 7.
Application Deployment 7-9 The Script1 window directory pane displays two partitions: Platform and Application. Depending on the type of flash chip, the number of partitions may change. Files can be added to each of the partitions. TCM functionality includes: • Opening a new or existing script file • Copying components to the script window • Saving the script file. Opening a New or Existing Script A script file can be created from scratch or based on an existing script file.
7 - 10 WT4070/90 Wearable Terminal Integrator Guide Figure 7-7 Configure Build Window 2. Select the items (partitions) to build using the check box(es) to the left of each named partition. 3. The Build Path defines where to store all built partitions. 4. Select (hex image) COMPRESSION to reduce the size and speed up the download. 5. Click OK and follow the on-screen instructions. If one of the partitions being built is the ESSID, a prompt appears requesting the ESSID value.
Application Deployment 7 - 11 Sending the Hex Image Using IPL Once the hex file is built, it can be downloaded to the wearable terminal using IPL. NOTE The wearable terminal must be inserted in the cradle with appropriate power supply connected to a power source, for the wearable terminal to reset into IPL. WT4070/90 1. Press the 1, 9 and Power button. The wearable terminal performs a cold boot. 2. The screen blanks and three brackets display “} } }”. Immediately press the P2 key.
7 - 12 WT4070/90 Wearable Terminal Integrator Guide Table 7-2 IPL Menu Partitions Partition Name Description Platform Contains the files in the Platform folder. Application Contains the files in the Application folder. Windows CE Contains the operating system for the wearable terminal. Monitor Contains the Monitor and IPL programs. Splash Screen Contains the splash screen that displays while booting the wearable terminal. Note: Splash screens are generated from .
Application Deployment 7 - 13 5. Use the up and down scroll buttons to select USB and press Enter. If this is the first time using USB transport, you might need to install the Symbol USB driver. Follow the screen prompts. 6. The USB Configuration menu appears. USB Configuration USB Standard Previous Top 7. Select USB Standard and press ENTER. The Download File? menu appears. Download File? Download Cancel Show Parms Previous Top Figure 7-11 Download File? Menu 8.
7 - 14 WT4070/90 Wearable Terminal Integrator Guide Download: “Partition Name” via USB USB Standard Press Enter to continue Figure 7-12 Parameters Screen Partition Name is the name of the partition selected in the Initial Program Loader menu. 9. Press Enter to return to the Download File? menu. 10. Use the up and down scroll buttons to select Download. Press Enter. The Downloading screen appears. Downloading: Partition Name via USB USB Standard waiting for input . . .
Application Deployment 7 - 15 12. Select the Image Files To Load. 13. In the Comm Port drop-down list, select USB: Symbol Device. 14. Click Download to begin the operation. 15. During download, the Downloading screen on wearable terminal displays the Device Status and a progress bar. 16. When complete, Device Status displays Result was: Success!, or in the case of an error, the cause of the error. 17. On completion, press ENTER to return to the IPL menu to select the next partition to download. 18.
7 - 16 WT4070/90 Wearable Terminal Integrator Guide 8. When complete, the message “Transfer Complete. Check the terminal for successful completion.” 9. Click OK. 10. Repeat steps 5 through 9 for each file to download. 11. To exit IPL, perform a cold boot. TCM Error Messages TCM validates the cells in the partition table when the Execute button is clicked. Cells highlighted in red contain an error. Partition loading is disabled until all errors are corrected.
Application Deployment 7 - 17 Table 7-3 TCM Error Messages (Continued) Error Description/Solution INVALID DIRECTORY In Script Properties window, the selected System File Path is not a valid directory. One of the disk sizes is one sector in size In Script Properties window, one of the disks is too small (one sector in size). This may cause problem while building images, especially when cushion is enabled. Increase the disk size.
7 - 18 WT4070/90 Wearable Terminal Integrator Guide This error message screen displays until you press any key. Once the screen is acknowledged, IPL returns to the Initial Program Loader main menu to wait for a new selection. To find the probable cause of the error, use the error number and/or the error text displayed on the screen to look up the error in Table 7-4. Table 7-4 IPL Errors Error Number Error Text Probable Cause Unknown error -1 A general error occurred. Retry the download.
Application Deployment 7 - 19 Table 7-4 IPL Errors (Continued) Error Number Error Text Probable Cause Exceeded max size -26 The download file is too large to fit into the space allocated for it. Either make the file smaller or increase the space allocated for it by altering the partition table. Partition is not valid on this device -27 The downloaded file specifies a partition entry that does not exist on the device.
7 - 20 WT4070/90 Wearable Terminal Integrator Guide If the default files are not used to create the new splash screens, be sure to preserve the image format. The formats are as follows: Table 7-5 Splash Screen Format Screen Type Color Dimensions 320 x 216 Color Format 8 bits per pixel* * 8 bits per pixel only applies to splash screen images. Once Windows CE is running, the color density is 16 bits per pixel.
Application Deployment 7 - 21 RegMerge.dll RegMerge.dll is a built-in driver that allows registry edits to be made to the Windows CE Registry. Regmerge.dll runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders during a cold boot. It then merges the registry changes into the system registry located in RAM.
7 - 22 WT4070/90 Wearable Terminal Integrator Guide Non-FFS Partitions Non-FFS Partitions include additional software and data pre-loaded on the wearable terminal that can be upgraded. Unlike FFS Partitions, these partitions are not visible when the operating system is running. They also contain system information. Non-FFS partitions include the following: • Windows CE: The complete Windows CE operating system is stored on Flash devices.
Chapter 8 Staging and Provisioning Introduction The MSP 3 Client Software is a set of software components that come pre-installed on the wearable terminal. The MSP 3 Client software consists of the following three components: Refer to the Mobility Services Platform 3.2 User’s Guide, p/n 72E-100158-06, for instructions for using the Rapid Deployment, AirBEAM Smart and MSP3 Agent clients.
8-2 WT4070/90 Wearable Terminal Integrator Guide
Chapter 9 Special Considerations Touch Panel User Interface Considerations When developing applications for a touch panel interface, touch panel activation only by the ball of the finger means there are limitations to what the user interface of an application can expect of a worker • User interface elements such as buttons, that require activation by a bare finger tip on the touch screen should not be smaller than 10 mm x 10 mm (as opposed to 5 mm x 5 mm if a stylus were an option).
9-2 WT4070/90 Wearable Terminal Integrator Guide 4. Ensure that the Disable backlight if not used for checkbox is checked. 5. In the drop-down list, select the amount of time after which the display will turn off. Set to 1 minute or a lower value that the user is comfortable with. To set the brightness level of the display: 1. Select Brightness tab. 2. Move the slider to 2 to conserve power. 3. Select OK.
Special Considerations 4. 9-3 Select OK. Wireless LAN To set the WLAN radio to maximum performance: 1. Select the wireless icon in the bottom lower right corner. 2. Select Manage Profiles. 3. Select your wireless profile, double click. 4. Select Edit. 5. Continuously select Next until the Battery Usage window appears. 6. Ensure the MAX Power Save radio button is selected.
9-4 WT4070/90 Wearable Terminal Integrator Guide
Chapter 10 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the wearable terminal, and provides troubleshooting solutions for potential problems during wearable terminal operating. Maintaining the Wearable Terminal For trouble-free service, observe the following tips when using the wearable computer: • Do not scratch the touch screen of the wearable computer. When activating with the wearable computer touch screen, use finger tips.
10 - 2 WT4070/90 Wearable Terminal Integrator Guide • Regularly replace all Velcro® straps on the wrist mount and wearable scanners, to ensure adequate adhesion of the Velcro. • On touch screen versions, periodically replace the screen protector, especially if it is scratched. Wrist Mount Cleaning Instructions It may be necessary to wash the wrist mount straps and replaceable pad when they become soiled. Remove the straps and pad from the wrist mount.
Maintenance & Troubleshooting 10 - 3 Lift Screen Protector Corner Figure 10-2 Removing the Screen Protector CAUTION Do not use a sharp object to remove the protector. Doing so can damage the touch screen. Battery Safety Guidelines • The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment. • Improper battery use may result in a fire, explosion, or other hazard.
10 - 4 WT4070/90 Wearable Terminal Integrator Guide • Seek medical advice immediately if a battery has been swallowed. • In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice. • If you suspect damage to your equipment or battery, contact Motorola Enterprise Mobility support to arrange for inspection.
Maintenance & Troubleshooting 10 - 5 4. Rub the cotton portion of the cotton tipped applicator back-and-forth across each connector. Do not leave any cotton residue on the connector. 5. Repeat at least three times. 6. Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt near the connector area. 7. Use a dry cotton tipped applicator and repeat steps 4 through 7. CAUTION Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 8.
10 - 6 WT4070/90 Wearable Terminal Integrator Guide 3. Rub the cotton portion of the cotton tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not let any cotton residue on the connector. 4. All sides of the connector should also be rubbed with the cotton tipped applicator. CAUTION Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 5.
Maintenance & Troubleshooting 10 - 7 Table 10-1 Troubleshooting the Wearable Terminal (Continued) Problem Rechargeable lithium-ion battery did not charge. Cause Solution Battery failed. Replace battery. If the wearable terminal still does not operate, try a warm boot, then a cold boot. See Resetting the Wearable Terminal on page 1-8. Wearable terminal removed from cradle while battery was charging. Insert wearable terminal in cradle and begin charging.
10 - 8 WT4070/90 Wearable Terminal Integrator Guide Table 10-1 Troubleshooting the Wearable Terminal (Continued) Problem Wearable terminal turns itself off. A message appears stating that the wearable terminal memory is full. (not applicable to voice only configuration). Cause Solution Wearable terminal is inactive. The wearable terminal turns off after a period of inactivity. If the wearable terminal is running on battery power, this period can be set to 30 sec., 1, 2, 3, 4, 5 or 6 minutes.
Maintenance & Troubleshooting 10 - 9 Table 10-1 Troubleshooting the Wearable Terminal (Continued) Problem The wearable terminal does not accept scan input. Cause Solution Scanning application is not loaded. Verify that the unit is loaded with a scanning application. See the System Administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Ensure wearable terminal is within proper scanning range.
10 - 10 WT4070/90 Wearable Terminal Integrator Guide Four Slot Spare Battery Charger Table 10-2 Troubleshooting The Four Slot Spare Battery Charger Symptom Batteries not charging. Possible Cause Solution Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Maintenance & Troubleshooting 10 - 11 Table 10-3 Troubleshooting the Four Slot Ethernet Cradle (Continued) Problem Cause During data communication, no data was transmitted, or transmitted data was incomplete. Solution Wearable terminal removed from cradle during communication. Replace wearable terminal in cradle and retransmit. Incorrect cable configuration. See the system administrator. Ethernet connection error. Link LED is not lit (see Link LED on page 2-10). See the system administrator.
10 - 12 WT4070/90 Wearable Terminal Integrator Guide Table 10-4 Troubleshooting the Single Slot USB Cradle (Continued) Symptom During data communications, no data was transmitted, or transmitted data was incomplete. Cannot ActiveSync with Host Computer Possible Cause Action Wearable terminal removed from cradle during communications. Replace wearable terminal in cradle and retransmit. Incorrect cable configuration. See the System Administrator.
Appendix A Technical Specifications Technical Specifications The following tables summarize the wearable terminal’s intended operating environment and general technical hardware specifications. Wearable Terminal The following table summarizes the wearable terminal’s intended operating environment. Table A-1 Technical Specifications Item Description Physical and Environmental Characteristics Dimensions With Standard Battery: 5.7 inches L x 3.7 inches W x 1.0 inch H (14.2 cm L x 9.3 cm H x 2.
A-2 WT4070/90 Wearable Terminal Integrator Guide Table A-1 Technical Specifications (Continued) Item Description Operating System Microsoft Windows CE 5.
Specifications Table A-1 Technical Specifications (Continued) Item Antenna Description Internal WPAN Wireless Data Communications Bluetooth Bluetooth Version 1.
A-4 WT4070/90 Wearable Terminal Integrator Guide Table A-1 Technical Specifications (Continued) Item Description Peripherals and Accessories Cradles Single Slot USB Four Slot Ethernet Printers Supports extensive line of Motorola approved printers, cables and accessories Charger Four Slot Battery Charger Other Accessories Headset adapter, freezer pouch, hip mount and wrist mount. Regulatory Electrical Safety Certified to UL60950-1, CSA C22.2 No.
Specifications Table A-2 RS309 Technical Specifications (Continued) Item Description Pitch ± 65 degrees from normal User Environment Operating Temperature -22 °F to 122 °F (-30 °C to 50 °C) Storage Temperature -40 °F to 140 °F (-40 °C to 60 °C) Humidity 5% to 95% non condensing Drop Specification 4 ft.(1.
A-6 WT4070/90 Wearable Terminal Integrator Guide Table A-3 RS409 Technical Specifications (Continued) Item Description Scan Rate 104 (± 12) scans/sec (bidirectional) Nominal Working Distance Density Code Type Far (inches) Far (inches) Yaw ± 50 degrees from normal Roll ± 35 degrees from vertical Pitch ± 65 degrees from normal 5 mil 39 4.75 8.75 7.5 mil 39 8.75 14.25 10 mil 13 mil 39 UPC 13.25 17.25 24.25 20 mil 40 mil 39 39 21.5 22.25 35.75 55 mil 39 27 (Guaranteed) 50.
Specifications RS507 Scanner Table A-4 RS507 Technical Specifications Item Description Physical and Environmental Characteristics Dimensions Triggerless, standard battery: 2.9 x 5.3 x 7.4 cm (1.16 x 2.1 x 2.92 in.) Triggerless, extended battery: 3.6 x 5.3 x 7.4 cm (1.42 x 2.1 x 2.92 in.) Triggered, standard battery: 2.9 x 5.3 x 7.4 cm (1.16 x 2.1 x 2.92 in.) Triggered, corded (cord length not included): 3.3 x 5.3 x 7.4 cm (1.3 x 2.1 x 2.92 in.) Weight Triggerless, standard battery: 121.4 g (4.3 oz.
A-8 WT4070/90 Wearable Terminal Integrator Guide Table A-4 RS507 Technical Specifications (Continued) Item Supported Symbologies Description 1D enabled by default: Codabar, Code 39, Code 128, EAN-13, EAN-8, Interleaved 2 of 5, UPC-A and UPC-E. Additionally supported by 1D: Code 11, Code 32 Pharmaceutical (PARAF), Code 93, MSI, Reduced Space Symbology (RSS-14, RSS Limited, RSS Expanded), Straight 2 of 5 IATA (two-bar start/stop), Straight 2 of 5 Industrial (three-bar start/stop), Trioptic, UPC-E1.
Specifications A-9 Table A-4 RS507 Technical Specifications (Continued) Item Description Environmental Sealing IP54 Electrostatic Discharge (ESD) ±15kV air discharge, ±8kV direct discharge. Power Cordless Standard battery: Li-Ion 970 mAh, 3.7 V with up to 35,000 scans (continuous) or up to 10 hours with 900 scans per hour on a single charge using fresh batteries. Extended battery: Li-Ion 1940 mAh, 3.
A - 10 WT4070/90 Wearable Terminal Integrator Guide Wearable Terminal Interface Connector Pin-Outs Pin 1 Figure A-1 Pin Locations Table A-6 Interface Connector Pin-Outs PIN Signal Name Function 1 SCANNER_DETECT_RIGHT Scanner detect. 2 USBH_N_RIGHT USB host negative. 3 GND Digital/system ground. 4 USBH_P_RIGHT USB host positive. 5 A_GND Analog ground. 6 HPOUTL_RIGHT_MIC+ Mic+ (default) or headphone out left. 7 U2_RXD Scanner serial RXD. 8 HPOUTER_RIGHT Headphone out right.
Specifications A - 11 Pin 1 Figure A-2 Cradle Connector Pin Locations Table A-7 Cradle Connector Pin-Outs PIN Number Signal Name Function 1 Power In 5.4 VDC input power. 2 ACC_OTG_VBUS 5.0 VDC input in client mode, 5.0 VDC output in host mode. 3 ACC_OTG_DP USB data positive. 4 ACC_OTG_DM USB data negative. 5 System GND System ground. 6 ACC_OTG_ID USB host/client ID pin input. (Low = USB Host, High = USB Client). 7 System Ground System ground.
A - 12 WT4070/90 Wearable Terminal Integrator Guide
Glossary Numeric 802.11. A group of wireless specifications developed by the Institute of Electrical and Electronics Engineers (IEEE). It specifies an over-the-air interface between a wireless client and a base station or between two wireless clients. 802.11a. Operates in the 5 GHz frequency range (5.125 to 5.85 GHz) with a maximum 54Mbit/sec. signaling rate. The 5 GHz frequency band is not as crowded as the 2.4 GHz frequency because it offers significantly more radio channels than the 802.
Glossary - 2 WT4070/90 Wearable Terminal Integrator Guide ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language. For example, it uses escape sequences to control the cursor, clear the screen and set colors. Communications programs support the ANSI terminal mode and often default to this terminal emulation for dial-up connections to online services. Association.
Glossary - 3 CDRH Class 2. No additional software mechanisms are needed to conform to this limit. Laser operation in this class poses no danger for unintentional direct human exposure. CHAP. (Challenge Handshake Authentication Protocol) A type of authentication in which the authentication agent (typically a network server) sends the client program a random value that is used only once and an ID value. Both the sender and peer share a predefined secret.
Glossary - 4 WT4070/90 Wearable Terminal Integrator Guide Device Configuration Package. The Symbol Device Configuration Package provides flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With this package hex images that represent flash partitions can be created and downloaded to the wearable terminal. DTE. See Data Terminal Equipment. E EAN.
Glossary - 5 Hz. Hertz; A unit of frequency equal to one cycle per second. Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification.
Glossary - 6 WT4070/90 Wearable Terminal Integrator Guide L laser scanner. A type of bar code reader that uses a beam of laser light. LASER. (Light Amplification by Stimulated Emission of Radiation) The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. LCD. See Liquid Crystal Display. LEAP.
Glossary - 7 NVM. Non-Volatile Memory. O ODI. See Open Data-Link Interface. Open Data-Link Interface (ODI). Novell’s driver specification for an interface between network hardware and higher-level protocols. It supports multiple protocols on a single NIC (Network Interface Controller). It is capable of understanding and translating any network information or request sent by any other ODI-compatible protocol into something a NetWare client can understand and process. Open System Authentication.
Glossary - 8 WT4070/90 Wearable Terminal Integrator Guide RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and signals used to transfer data serially from one device to another. S Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol. Its three main components are: 1. Light source (laser or photoelectric cell) - illuminates a bar code. 2.
Glossary - 9 T TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork dissimilar systems. This standard is the protocol of the Internet and has become the global standard for communications. TCP provides transport functions, which ensures that the total amount of bytes sent is received correctly at the other end. UDP is an alternate transport that does not guarantee delivery.
Glossary - 10 WT4070/90 Wearable Terminal Integrator Guide U Visible Laser Diode (VLD). A solid state device which produces visible laser light. W Warm Boot. A warm boot restarts the wearable terminal by closing all running programs. All data that is not saved to flash memory is lost. WAP. (Wireless Application Protocol) A set of specifications, developed by the WAP Forum, that lets developers using Wireless Markup Language build networked applications designed for handheld wireless devices.
Index Numerics B 128-Bit WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 40-Bit WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 802.11 ESSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 802.11d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34 backup battery charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 band selection 2.4 GHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 WT4070/90 Wearable Terminal Integrator Guide Enterprise Mobility Developer Kit for eVC4 . . . . . . . . xvii error messages . . . . . . . . . . . . . . . . . . . . . . . 7-16, 7-17 exporting a profile . . . . . . . . . . . . . . . . . . . . . 5-24, 5-37 spare batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 temperature range . . . . . . . . . . . . . . . . . . . . . . . A-9 charging batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 charging spare batteries . .
Index - 3 K keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 keypad backlight saving power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv known APs APs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32 L laser safety . . . . . . . . . . . . . . . . . . . . . . . . A-5, A-6, A-9 LEAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 WT4070/90 Wearable Terminal Integrator Guide splash screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22 creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19 starting the wearable terminal . . . . . . . . . . . . . . .1-4, 1-7 static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18 storage temperature . . . . . . . . . . . . . .A-2, A-5, A-6, A-8 subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc.
