WT4070/90 Wearable Terminal User Guide
WT4070/90 Wearable Terminal User Guide 72E-87633-02 Rev A February 2007
ii WT4070/90 Wearable Terminal User Guide © 2006-7 Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
Getting Started Revision History Changes to the original manual are listed below: Change Date Description -01 Rev. A 09/25/2006 Initial Release -02 Rev. A 02/22/2007 Add new start up windows, Fusion 2.5 information, 128 MB Flash configuration.
iv WT4070/90 Wearable Terminal User Guide
Table of Contents Chapter 1 Table of Contents Patents........................................................................................................................... ii Revision History ............................................................................................................. iii About This Guide Introduction .................................................................................................................... v Documentation Set ...............................
vi WT4070/90 Wearable Terminal User Guide Display .......................................................................................................................... Start Up Window ..................................................................................................... Windows CE 5.0 Desktop ....................................................................................... Status Icons ...............................................................................................
Table of Contents Troubleshooting ............................................................................................................ Wearable Terminal .................................................................................................. Four Slot Ethernet Cradle ....................................................................................... Four Slot Spare Battery Charger ............................................................................ Single Slot USB Cradle .....
viii WT4070/90 Wearable Terminal User Guide
About This Guide About This Guide Introduction This guide provides information about using the WT4070/90 family of mobile terminals and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation set for the WT4070/90 is divided into guides that provide information for specific user needs. • Microsoft Application Guide - describes how to use Microsoft developed applications.
vi WT4070/90 Wearable Terminal User Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads WT4070 WLAN: 802.11b/g WPAN: Bluetooth 2.8” QVGA Color 128 MB RAM/ 64 MB Flash Optional accessory Windows CE 5.0 Professional Two-color or Triple-tap Alphanumeric Keypad WT4090 WLAN: 802.11a/b/g WPAN: Bluetooth 2.8” QVGA Color 128 MB RAM/ 64 MB Flash or 128 MB RAM/ 128 MB Flash Optional accessory Windows CE 5.
About This Guide Software Versions This guide covers various software configurations and references are made to operating system or software versions for: • OEM version • Fusion version. OEM Software To determine the OEM software version: 1. Press CTRL and then ESC to open the Start menu. 2. Using the navigation keys, select Settings. 3. Press the Blue key and the down arrow to open the Control Panel sub-menu. 4. Press ENTER key to launch Control Panel. 5.
viii WT4070/90 Wearable Terminal User Guide Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started, provides information on getting the wearable terminal up and running for the first time. • Chapter 2, Using the Wearable Terminal, explains how to use the wearable terminal. This includes instructions for powering on and resetting the wearable terminal, entering and capturing data.
About This Guide • WT4090 Quick Start Guide, p/n 72-86717-xx • WT4090 Windows® CE 5.0 Regulatory Guide, p/n 72-86718-xx • WT4090 Wearable Terminal Integrator Guide, p/n 72E-87638-xx • RS309 Scanner Quick Reference Guide, p/n 72-86011-xx • RS409 Scanner Quick Reference Guide, p/n 72-86010-xx • Symbol Application Guide for Symbol Devices, p/n 72E-68901-xx • Microsoft Applications for Windows Mobile and CE 5.
x WT4070/90 Wearable Terminal User Guide
Getting Started Chapter 1 Chapter 1 Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the wearable terminal and explains how to install and charge the batteries and start the wearable terminal for the first time.
1-2 WT4070/90 Wearable Terminal User Guide Table 1-1 Parts of the WT4070/90 Item Description Display Displays the application and data stored on the device. Power Button Places the wearable terminal in to the suspend mode or resumes normal operation. Performs a warm boot when held down for five seconds. See Resetting the Wearable Terminal on page 2-14 for information about performing a warm boot. Charge Status LED Indicates the charging status of the battery. Speaker Provides audio playback.
Getting Started 1-3 Accessories Table 1-2 lists the major accessories available for the wearable terminal: Table 1-2 Wearable Terminal Accessories Accessory Description Single Slot USB Cradle Charges the wearable terminal main battery and a spare battery. It also synchronizes the wearable terminal with a host computer through a USB connection. Four Slot Ethernet Cradle Charges up to four wearable terminals (with main battery installed) and provides communication through an Ethernet connection.
1-4 WT4070/90 Wearable Terminal User Guide Scan LED Connector Rotating Scan Assembly Exit Window Ring Mount Finger Strap Trigger Assembly Scan Trigger Figure 1-2 RS409 Scanner Protective Cap Scan LED Trigger Connector Interface Connector Exit Window Trigger Cable Scan Button Interface Cable Figure 1-3 RS309 Scanner
Getting Started 1-5 Getting Started In order to start using the wearable terminal for the first time: • Install the main battery • Charge the main battery and backup battery • Install the wearable terminal onto the wrist mount • Install an optional scanner • Start the wearable terminal. NOTE The main battery can be charged before or after installation into the wearable terminal.
1-6 WT4070/90 Wearable Terminal User Guide Charging the Battery Charging the Main Battery and Memory Backup Battery Before using the wearable terminal for the first time, charge the main battery until the amber Charge Status LED remains lit (see Table 1-3 on page 1-6 for charge status indications). The wearable terminal is equipped with a memory backup battery which automatically charges from the main battery whether or not the wearable terminal is operating or is in suspend mode.
Getting Started 1-7 Charging Spare Batteries Use the following accessories to charge spare batteries: • Single Slot USB Cradle • Four Slot Spare Battery Charger. To charge a spare battery: 1. Ensure the accessory used to charge the spare battery is connected to the appropriate power source. 2. Insert the spare battery into the accessory’s spare battery charging slot with the charging contacts facing down (over the charging pins) and gently press down on the battery to ensure proper contact. 3.
1-8 WT4070/90 Wearable Terminal User Guide Installing the Wrist Mount The wrist mount provides the mounting of the wearable terminal on the forearm for hands-free applications. Refer to the Wrist Mount Installation Guide for information on the wrist mount. Mounting Bracket Release Lever Figure 1-6 Wrist Mount To install the wrist mount: 1. Determine which arm the wrist mount will be used on. 2. Install the short strap on the end closest to the wrist. 3. Install the long strap on the other end. 4.
Getting Started 8. 1-9 If necessary, loosen and re-tighten the straps. Figure 1-8 Wearable Terminal and Wrist Mount To remove the wearable terminal from the wrist mount, press down on the release lever and slide the wearable terminal out.
1 - 10 WT4070/90 Wearable Terminal User Guide Connecting a Scanner The RS309 and RS409 scanners can be used with the wearable terminal. Refer to RS309 Scanner on page 3-9 and RS409 Scanner on page 3-7 for procedures for connecting the scanner to the wearable terminal. Starting the Wearable Terminal Press the Power button to turn on the wearable terminal. If the wearable terminal does not power on, perform a cold boot. See Resetting the Wearable Terminal on page 2-14.
Chapter 2 Using the Wearable Terminal Chapter 2 Chapter 2 Using the Wearable Terminal Introduction This chapter explains the physical buttons and controls on the wearable terminal, and provides basic instructions for using the wearable terminal, including powering on and resetting the wearable terminal, using a headset, entering information and scanning. This chapter also details the operation of the Windows CE 5.0 operating system including the desktop, applications and settings.
2-2 WT4070/90 Wearable Terminal User Guide LED Indicators The Charge Status LED indicates the WT4090 charging status when the WT4090 is in a cradle. Table 2-1 describes the Charge Status LED indications. Charge Status LED Figure 2-2 Charge Status LED Table 2-1 Charge Status LED Indications LED State Indication Off Wearable terminal is not in cradle. Wearable terminal not placed correctly. Charger is not powered. Slow Blinking Amber Main battery in wearable terminal is charging.
Using the Wearable Terminal 2-3 Keypads The wearable terminal has the following keypads: • Two-color alphanumeric keypad • Triple-tap (cell phone like) alphanumeric keypad. Two-color Alphanumeric Keypad The two-color alphanumeric keypad contains application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function keys (blue, orange and gray).
2-4 WT4070/90 Wearable Terminal User Guide Table 2-2 Two-color Alphanumeric Keypad Descriptions Key Orange Description Press and release the Orange key to activate alphabetic characters (shown on the keypad in orange). The Gray Press and release the Gray key to activate alphabetic characters (shown on the keypad in gray). The Blue icon appears on the Windows CE desktop taskbar. icon appears on the Windows CE desktop taskbar.
Using the Wearable Terminal 2-5 Triple-Tap Alphanumeric Keypad The triple-tap alphanumeric keypad contains application keys, scroll keys and function keys. The keypad is color-coded to indicate the alternate function keys (blue and orange). Note that keypad functions can be changed by an application so the wearable terminal’s keypad may not function exactly as described. See Table 2-3 on page 2-5 for key and button descriptions and Table 2-4 on page 2-6 for the keypad’s special functions.
2-6 WT4070/90 Wearable Terminal User Guide Table 2-3 Triple-tap Alphanumeric Keypad Descriptions (Continued) Key Description Alphanumeric In default state, produces the numeric value on the key. In Alpha state, produces the lower case alphabetic characters shown in orange text. For example, press and release the Orange key and then press the 5 key twice to produce the lowercase letter ‘k’. When the SHIFT key is pressed in Alpha state, the upper case alphabetic characters on the key are produced.
Using the Wearable Terminal Table 2-4 Special Character Generation Map (Continued) Special Character Two-color Keypad Triple-tap Keypad .
2-8 WT4070/90 Wearable Terminal User Guide Table 2-4 Special Character Generation Map (Continued) Special Character Two-color Keypad Triple-tap Keypad } (close curly bracket) Shift - Blue - Orange - 3 Shift - Blue - Orange - 3 | (pipe) Shift - Blue - Orange - 4 Shift - Blue - Orange - 4 ~ (tilde) Shift - Blue - Orange - 5 Shift - Blue - Orange - 5 < (less than sign) Shift - Blue - Orange - 6 Shift - Blue - Orange - 6 > (greater than sign) Shift - Blue - Orange - 7 Shift - Blue - Orange -
Using the Wearable Terminal 2-9 Display The wearable terminal is factory installed with the Windows CE 5.0 operating system. When the wearable terminal starts, it automatically launches the Start Up application. NOTE A customer specific application can be configured to automatically start-up and the Windows CE 5.0 desktop and Start Up application might not be visible or accessible. Start Up Window The Start Up window allows the user to launch specific applications by using the keypad.
2 - 10 WT4070/90 Wearable Terminal User Guide Table 2-5 Start Up Item Descriptions Launch Number Item Description Demo Apps 6 Opens a sub-window that contains sample demonstration applications. Exit 7 Closes the Start Up window. Windows CE 5.0 Desktop The following paragraphs describe the Windows CE 5.0 desktop. Depending upon the customer’s configuration of the wearable terminal, the desktop may not be available.
Using the Wearable Terminal 2 - 11 Table 2-6 Status Icons (Continued) Status Icon Description This icon is displayed when the memory backup battery level is low. Charge the battery. This icon indicates that the battery is fully charged (100% charged). The battery status icons provide the battery status in 10% increments from 10% to 100%. This displays when the terminal is connected to a host computer with ActiveSync. Wireless connection status icon. Indicates WLAN signal strength.
2 - 12 WT4070/90 Wearable Terminal User Guide Table 2-7 Key Combinations Action Key Combination Access a menu bar in an application ALT - ALT Press a button or select a check box in an application TAB until the item is highlighted then SPACE. Display a pop-up context menu ALT - ENTER Throughout this guide you will be instructed to select an item. You must use a key combination to select that item. For example: To perform: “Select Start > Programs > Windows Explorer” 1.
Using the Wearable Terminal 2 - 13 Figure 2-8 Navigating Menus Navigating Tabs Some applications contain multiple pages with tabs indicating each page. Use the TAB key to highlight the tab. A dashed box appears around the tab name. Use the left and right navigation keys to move to the next or previous tab. Selected Tab Figure 2-9 Navigating Tabs Navigating Fields To navigate from one field to another, press the TAB key.
2 - 14 WT4070/90 Wearable Terminal User Guide Selecting Items in a List Use a combination of key sequences to select items in a folder or list. To select continuous items in a folder or list: 1. Open the folder or list. 2. Use the scroll keys to move to the first item to select. 3. Press SHIFT - scroll key (either up or down) to select the next item. 4. Repeat the SHIFT - scroll key combination to select remaining items. 5. Perform the desired function.
Using the Wearable Terminal 2 - 15 Performing a Cold Boot A cold boot restarts the wearable terminal and erases all user stored records and entries that are not saved in flash memory (Application and Platform folders). Never perform a cold boot unless a warm boot does not solve the problem. NOTE Any data previously synchronized with a computer can be restored during the next ActiveSync operation. To perform a cold boot press and simultaneously hold the 1, 9 and Power button.
2 - 16 WT4070/90 Wearable Terminal User Guide Data Capture Wearable terminals used with an optional wearable laser scanner allow collection of data by scanning one dimensional bar codes. Laser Scanning Wearable terminals with an optional wearable laser scanner have the following features: • Reading of a variety of bar code symbologies, including the most popular linear, postal, and 1-D code types. • Advanced intuitive laser aiming for easy point-and-shoot operation.
Using the Wearable Terminal 2 - 17 Figure 2-11 Laser Scanner Aiming Pattern Release the trigger. 4. Scanning Tips Optimal scanning distance varies with bar code density and scanner optics. • Hold the scanner farther away for larger symbols. • Move the scanner closer for symbols with bars that are close together. NOTE Scanning procedures depend on the application and wearable terminal configuration. An application may use different scanning procedures from the one listed above.
2 - 18 WT4070/90 Wearable Terminal User Guide Waking the Wearable Terminal The wake up conditions define what actions wake up the wearable terminal after it has gone into suspend mode. The wearable terminal can go into suspend mode by either pressing the Power button or automatically by control panel time-out settings. These settings are configurable and the factory default settings are shown in Table 2-9.
Chapter 3 Accessories Chapter 3 Chapter 3 Accessories Introduction The wearable terminal accessories provide a variety of product support capabilities. Accessories include cradles, cables and scanners. Cradles • Single Slot USB cradle charges the wearable terminal main battery and a spare battery. It also synchronizes the wearable terminal with a host computer through either a serial or a USB connection.
3-2 WT4070/90 Wearable Terminal User Guide Single Slot USB Cradle This section describes how to use a Single Slot USB cradle (Figure 3-1) with the wearable terminal. For USB communication setup procedures refer to the WT4090 Integrator Guide. Scanner Placed in Well Spare Battery Spare Battery Charging LED Figure 3-1 Single Slot USB Cradle CAUTION Use only a Symbol approved power supply output rated 12 VDC and minimum 3.3 A.
Accessories • Charges the wearable terminal’s battery and a spare battery. • Provides a location for storing a scanner when a wearable terminal is docked in the cradle. 3-3 Battery Charging Indicators The Single Slot USB cradle can charge the wearable terminal’s main battery and a spare battery simultaneously. The wearable terminal’s amber Charge Status LED indicates the status of the battery charging in the wearable terminal. See Table 1-3 on page 1-6 for charging status indications.
3-4 WT4070/90 Wearable Terminal User Guide Four Slot Ethernet Cradle This section describes how to use a Four Slot Ethernet cradle (Figure 3-2) with the wearable terminal. For Ethernet communication setup procedures refer to the WT4090 Integrator Guide. Scanner Well Figure 3-2 Four Slot Ethernet Cradle The Four Slot Ethernet cradle: • Connects up to four wearable terminals to an Ethernet network. • Provide 5.4 VDC power for operating the wearable terminal and charging the battery.
Accessories 3-5 Battery Charging The four slot Ethernet cradle can charge up to four wearable terminals simultaneously. To charge the wearable terminal: 1. Slide the wearable terminal into the wearable terminal slot. 2. The wearable terminal amber Charge Status LED indicates the wearable terminal battery charging status. The Standard Battery usually charges in less than four hours.See Table 3-1 for charging status indications. 3.
3-6 WT4070/90 Wearable Terminal User Guide Four Slot Spare Battery Charger This section describes how to use the Four Slot Spare Battery Charger to charge up to four wearable terminal spare batteries. Spare Battery Charging Well (4) Spare Battery Spare Battery Charging LEDs (4) Figure 3-3 Four Slot Spare Battery Charger CAUTION Use only a Symbol approved power supply output rated 12 VDC and minimum 3.3 A. Use of an alternative power supply will void the product warranty and may cause product damage.
Accessories 3-7 RS409 Scanner To connect the RS409 scanner to the wearable terminal: NOTE There are two RS409 configurations available. The short cable configuration connects the RS409 to the wearable terminal mounted on the arm. The extended cable configuration connects the RS409 to the WT4090 mounted on the hip. 1. Remove the rubber plug from the wearable terminal interface connector. 2. Connect the RS409 interface cable to the wearable terminal interface connector.
3-8 WT4070/90 Wearable Terminal User Guide 4. Rotate the trigger assembly to the correct position for the hand that the scanner mounts to. 5. Slide the RS409 onto the index finger with the scan trigger next to the thumb. Figure 3-6 Place the RS409 on Index Finger 6. Tighten the finger strap. Figure 3-7 Tightening Straps 7. If required, cut excess finger strap material. After connecting the scanner, warm boot the wearable terminal.
Accessories 3-9 RS309 Scanner The RS309 connects to the wearable terminal and mounts on the back of either hand using the RS309 glove. 1. Remove the rubber plug from the wearable terminal interface connector. 2. Connect the RS309 trigger cable to the back of the RS309. Trigger Connector Figure 3-8 Connecting Trigger Cable to RS309 NOTE There are two interface cables available. The standard interface cable connects the RS309 to the wearable terminal mounted on the arm.
3 - 10 WT4070/90 Wearable Terminal User Guide 5. Connect the RS309 interface cable to the back of the RS309. Interface Connector Figure 3-10 Connecting Interface Cable to RS309 6. Mount the RS309 on the RS309 glove. Refer to the RS309 Glove Installation Guide for information on mounting the RS309. 7. Route the trigger cable around the side of the RS309, next to the index finger. 8. Slide the trigger mount on the index finger, with the button positioned next to the thumb, and adjust the velcro strap.
Accessories 3 - 11 Wired Headset You can use a mono headset with a microphone for audio communication with an audio enabled application. The Headset Adapter is required to connect a headset with a standard 2.5 mm jack to the wearable terminal. NOTE Symbol recommends 2.5 mm jack headset, p/n 50-11300-050. Figure 3-12 Typical Headset Connected to Headset Adapter Refer to the WT4070/90 Integrator Guide for instructions on assembling the headset and Headset Adapter.
3 - 12 WT4070/90 Wearable Terminal User Guide
Maintenance & Troubleshooting Chapter 4 Chapter 4 Chapter 4 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the wearable terminal, and provides troubleshooting solutions for potential problems during wearable terminal operation. Maintaining the Wearable Terminal For trouble-free service, observe the following tips when using the wearable terminal: • Protect the wearable terminal from temperature extremes.
4-2 WT4070/90 Wearable Terminal User Guide Troubleshooting Wearable Terminal Table 4-1 Troubleshooting the Wearable Terminal Problem Wearable terminal does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the wearable terminal. Lithium-ion battery not installed properly. Ensure battery is installed properly. See Installing and Removing the Main Battery on page 1-5. System crash. Perform a warm boot.
Maintenance & Troubleshooting 4-3 Table 4-1 Troubleshooting the Wearable Terminal (Continued) Problem No sound is audible. Cause Volume setting is low or turned off. Solution Adjust volume. Change volume settings by selecting Start > Settings > Control Panel > Volume & Sounds icon > Volume tab. Move the slider to change the volume level. Wearable terminal turns itself off. A message appears stating that the wearable terminal memory is full. Wearable terminal is inactive.
4-4 WT4070/90 Wearable Terminal User Guide Table 4-1 Troubleshooting the Wearable Terminal (Continued) Problem The wearable terminal does not accept scan input. WLAN connection is lost when the wearable terminal is connected to a host computer using ActiveSync. Cause Solution Scanning application is not loaded. Verify that the unit is loaded with a scanning application. See the System Administrator. Unreadable bar code. Ensure the symbol is not defaced.
Maintenance & Troubleshooting 4-5 Four Slot Ethernet Cradle Table 4-2 Troubleshooting the Four Slot Ethernet Cradle Problem Cause Solution Wearable terminal amber Charge Status LED does not light when wearable terminal inserted. Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. Wearable terminal is not correctly seated. Remove and re-insert the wearable terminal into the cradle, ensuring it is correctly seated.
4-6 WT4070/90 Wearable Terminal User Guide Four Slot Spare Battery Charger Table 4-3 Troubleshooting The Four Slot Spare Battery Charger Symptom Batteries not charging. Possible Cause Solution Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery. Battery contacts not connected to charger.
Maintenance & Troubleshooting 4-7 Single Slot USB Cradle Table 4-4 Troubleshooting the Single Slot USB Cradle Symptom Possible Cause Charge Status LEDs do not light when wearable terminal or spare battery is inserted. Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. Wearable terminal is not seated firmly in the cradle. Remove and re-insert the wearable terminal into the cradle, ensuring it is firmly seated.
4-8 WT4070/90 Wearable Terminal User Guide Table 4-4 Troubleshooting the Single Slot USB Cradle (Continued) Symptom During data communications, no data was transmitted, or transmitted data was incomplete. Cannot ActiveSync with Host Computer Possible Cause Solution Wearable terminal removed from cradle during communications. Replace wearable terminal in cradle and retransmit. Incorrect cable configuration. See the System Administrator.
Specifications Appendix A Appendix A Specifications Technical Specifications The following tables summarize the wearable terminal’s intended operating environment and general technical hardware specifications. Wearable Terminal The following table summarizes the wearable terminal’s intended operating environment. Table A-1 Technical Specifications Item Description Physical and Environmental Characteristics Dimensions 5.7 inches L x 3.7 inches W x 1.0 inch H (14.2 cm L x 9.3 cm H x 2.
A-2 WT4070/90 Wearable Terminal User Guide Table A-1 Technical Specifications (Continued) Item Description Battery Charging Temperature 32 °F to 104 °F (0 °C to +40 °C) ambient temperature range. Humidity 5% to 95% non condensing Drop Specification Multiple 4 ft.(1.
Appendix A: Specifications A - 3 Table A-1 Technical Specifications (Continued) Item Description Peripherals and Accessories Cradles Single Slot USB Four Slot Ethernet Printers Supports extensive line of Symbol approved printers, cables and accessories Charger Four Slot Battery Charger Other Accessories Headset adapter to a 2.5 mm barrel jack headset connector Regulatory Electrical Safety Certified to UL60950-1, CSA C22.2 No.
A-4 WT4070/90 Wearable Terminal User Guide Table A-2 RS309 Technical Specifications (Continued) Item Description Pitch ± 65 degrees from normal User Environment Operating Temperature -22 °F to 122 °F (-30 °C to 50 °C) Storage Temperature -40 °F to 140 °F (-40 °C to 60 °C) Humidity 5% to 95% non condensing Drop Specification 4 ft.(1.
Appendix A: Specifications A - 5 Table A-3 RS409 Technical Specifications (Continued) Item Description Scan Rate 104 (± 12) scans/sec (bidirectional) Nominal Working Distance Density Code Type Far (inches) Far (inches) Yaw ± 50 degrees from normal Roll ± 35 degrees from vertical Pitch ± 65 degrees from normal 5 mil 39 4.75 8.75 7.5 mil 39 8.75 14.25 10 mil 13 mil 39 UPC 13.25 17.25 24.25 20 mil 40 mil 39 39 21.5 22.25 35.75 55 mil 39 27 (Guaranteed) 50.
A-6 WT4070/90 Wearable Terminal User Guide Cradles Table A-4 Accessory Specifications Single Slot USB Cradle Four Slot Ethernet Cradle Four Slot Spare Battery Charger Operating Temperature 32 °F to 122 °F (0 °C to +50 °C) 32 °F to 104 °F (0 °C to +40 °C) Storage Temperature -40 °F to 158 °F (-40 °C to 70 °C) Battery Charging Temperature 32 °F to 104 °F (0 °C to +40 °C) ambient temperature Humidity 5% to 95% non-condensing Size (L x W x H) 6.6 in. x 5.1 in. x 3.9 in. (16.8 cm x 13.0 cm x 9.
Regulatory Appendix B Appendix B Regulatory Introduction This appendix contains the accessory power supply regulatory compliance statements. Accessory Power Supply Regulatory Compliance Table B-1 Accessory Power Supplies, Regulatory Compliance Statements Accessory Power Supplies Regulatory Compliance Statements Single Slot USB Cradle Power Supply Four Slot Battery Charger Power Supply Use only a Symbol-approved power supply output rated 12 VDC and minimum 3.3 A.
B-2 WT4070/90 Wearable Terminal User Guide
Glossary GlossaryGlossary A API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Application Programming Interface. See API. ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language. For example, it uses escape sequences to control the cursor, clear the screen and set colors.
Glossary - 2 WT4070/90 Wearable Terminal User Guide Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory is used to store one ASCII character. boot or boot-up. The process a computer goes through when it starts. During boot-up, the computer can run self-diagnostic tests and configure hardware and software. C CDRH.
Glossary - 3 Decode. To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar code scanned. Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or numbers encoded within a bar code symbol. Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption and Key. Depth of Field.
Glossary - 4 WT4070/90 Wearable Terminal User Guide H Hard Reset. See Cold Boot. Hz. Hertz; A unit of frequency equal to one cycle per second. Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation.
Glossary - 5 IP Address. (Internet Protocol address) The address of a computer attached to an IP network. Every client and server station must have a unique IP address. A 32-bit address used by a computer on a IP network. Client workstations have either a permanent address or one that is dynamically assigned to them each session. IP addresses are written as four sets of numbers separated by periods; for example, 204.171.64.2. IPX/SPX. Internet Package Exchange/Sequential Packet Exchange.
Glossary - 6 WT4070/90 Wearable Terminal User Guide MIL. 1 mil = 1 thousandth of an inch. MIN. Mobile Identification Number. The unique account number associated with a cellular device. It is broadcast by the cellular device when accessing the cellular system. N Nominal. The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive and negative deviations from this value. O Open Data-Link Interface (ODI).
Glossary - 7 R RAM. Random Access Memory. Data in RAM can be accessed in random order, and quickly written and read. Resolution. The narrowest element dimension which is distinguished by a particular reading device or printed with a particular device or method. RF. Radio Frequency. ROM. Read-Only Memory. Data stored in ROM cannot be changed or removed. Router. A device that connects networks and supports the required protocols for packet filtering.
Glossary - 8 WT4070/90 Wearable Terminal User Guide Subnet. A subset of nodes on a network that are serviced by the same router. See Router. Subnet Mask. A 32-bit number used to separate the network and host sections of an IP address. A custom subnet mask subdivides an IP network into smaller subsections. The mask is a binary pattern that is matched up with the IP address to turn part of the host ID address field into a field for subnets. Default is often 255.255.255.0. Substrate.
Glossary - 9 U UPC. Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars and two spaces, each of which is any of four widths. The standard symbology for retail food packages in the United States. UDP. User Datagram Protocol. A protocol within the IP protocol suite that is used in place of TCP when a reliable delivery is not required.
Glossary - 10 WT4070/90 Wearable Terminal User Guide
Index IndexIndex Numerics 1-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 28-key keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 warm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1, 2-14 bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii buttons power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 A C accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 WT4070/90 Wearable Terminal User Guide laser scanning . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 one dimensional bar codes . . . . . . . . . . . . . . . . 2-16 scan angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 scan range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 date/time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 DCP for WT4090c50 . . . .
Index - 3 S W scan status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 scan status See also data capture scanning bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 See data capture . . . . . . . . . . . . . . . . . . . . . . . 2-16 screen Symbol splash screen . . . . . . . . . . . . . . . . . . . 1-10 serial/USB cradle . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 WT4070/90 Wearable Terminal User Guide
Motorola, Inc. One Symbol Plaza Holtsville, New York 11742-1300 http://www.symbol.
