User`s guide
Table Of Contents
- 1. PREFACE
- 2. CHECKLIST AND REQUIREMENTS
- 3. INSTALLATION AND USE
- 3.1 PROGRAMMER CHECK AND CONNECTION TO PC
- 3.2 PROGRAMMER FIRMWARE UPDATE
- 4. INTERFACE TYPES
- 5. WORKING WITH TARGET MCU
- 6. FILE OPERATIONS
- 7. ERRORS AND TROUBLESHOOTING
- 8. WARRANTY STATEMENT
- 9. APPENDIX
- Figure 2. In-Circuit programming schematic diagram for HC912/9S12 MCU
- Figure 3. In-Circuit wiring diagram for MC68HC912B32, 80-PIN QFP Package
- Figure 4. In-Circuit wiring diagram for MC68HC912D60/DG128, 112-PIN TQFP Package
- Figure 5. In-Circuit wiring diagram for MC68HC912D60A/DG128A, 112-PIN LQFP Package
- Figure 6. In-Circuit wiring diagram for MC68HC(9)12D60, 80-PIN QFP Package
- Figure 7. In-Circuit wiring diagram for MC68HC912D60A, 80-PIN QFP Package
- Figure 8. In-Circuit wiring diagram for MC9S12Dx64/Dx128/Dx256, 80-PIN QFP Package
- Figure 9. In-Circuit wiring diagram for MC9S12Dx64/Dx128/Dx256, 112-PIN LQFP Package
- Figure 10. In-Circuit wiring diagram for MC9S12H-Family 112-PIN LQFP Package
- Figure 11. In-Circuit wiring diagram for MC9S12H-Family 144-PIN LQFP Package
Load EEPROM/FLASH data from file (see Section 6.1) or enter data to Hex Editor.
HC912-Programmer software.
SH” button.
hat means that +5 voltage
mer became permanent green, programming
If some
SH programming, for a first
file.
ket on HC912-Programmer in according to 1 pin-
r.
2-Programmer software (“Device” Button).
HC912-Programmer became to green light. That means that +5 voltage
HC912-Programmer became permanent green light, reading
When read sequence successfully completed it is necessarily to save memory dump to
file (se
If some 7.
&
t MCU HC912-Programmer must
in-
r.
Select “Program Sequence” panel in
Press “EEPROM/FLA
Press “Start” button.
LED D4 on HC912-Programmer became to green light. T
regulator switched on and VCC applied to target MCU.
Now HC912-Programmer automatically detects MCU bus speed.
When LED D1 on HC912-Program
completed. Target MCU powered off.
errors appeared during programming process refer to Section 7.
& Note: Extra care must be taken when programming the EEPROM Shadow
Word/Byte.
& Note: Strongly recommended before EEPROM/FLA
time, read EEPROM/FLASH contents and save it to
5.1.3 On-Board EEPROM/FLASH reading example
Mount target MCU on corresponding QFP adaptor.
Insert adaptor to Motorola Device Soc
key (see Figure 1).
Remove cable from BDM ICP connector (see Figure 1).
Apply power to HC912-Programme
Select device in HC91
Select “Read Sequence” panel in HC912-Programmer software.
Press “EEPROM/FLASH” button.
Press “Start” button.
LED D4 on
regulator switched on and VCC applied to target MCU.
When LED D1 on
completed.
e Section 6.2).
errors appeared during reading process refer to Section
& Note: When target MCU mounted on adaptor check contacts careful to avoid
short circuit. Otherwise target MCU can be damaged!
Note: During removing the adaptor with targe
be powered off to avoid damaging of programmer and target MCU!
5.1 ample .4 On-Board EEPROM/FLASH programming ex
Mount target MCU on corresponding QFP adaptor.
Insert adaptor to Motorola Device Socket on HC912-Programmer in according to 1 p
key (see Figure 1).
ector (see Figure 1). Remove cable from BDM ICP conn
2-Programme Apply power to HC91
Select device in HC912-Programmer software (“Device” Button).
Load EEPROM/FLASH data from file (see Section 6.1) or enter data to Hex Editor.
©ETL 2004-2006 MC68HC912/9S12 Programmer User’s Guide 8