User`s guide
Table Of Contents
- 1. PREFACE
- 2. CHECKLIST AND REQUIREMENTS
- 3. INSTALLATION AND USE
- 3.1 PROGRAMMER CHECK AND CONNECTION TO PC
- 3.2 PROGRAMMER FIRMWARE UPDATE
- 4. INTERFACE TYPES
- 5. WORKING WITH TARGET MCU
- 6. FILE OPERATIONS
- 7. ERRORS AND TROUBLESHOOTING
- 8. WARRANTY STATEMENT
- 9. APPENDIX
- Figure 2. In-Circuit programming schematic diagram for HC912/9S12 MCU
- Figure 3. In-Circuit wiring diagram for MC68HC912B32, 80-PIN QFP Package
- Figure 4. In-Circuit wiring diagram for MC68HC912D60/DG128, 112-PIN TQFP Package
- Figure 5. In-Circuit wiring diagram for MC68HC912D60A/DG128A, 112-PIN LQFP Package
- Figure 6. In-Circuit wiring diagram for MC68HC(9)12D60, 80-PIN QFP Package
- Figure 7. In-Circuit wiring diagram for MC68HC912D60A, 80-PIN QFP Package
- Figure 8. In-Circuit wiring diagram for MC9S12Dx64/Dx128/Dx256, 80-PIN QFP Package
- Figure 9. In-Circuit wiring diagram for MC9S12Dx64/Dx128/Dx256, 112-PIN LQFP Package
- Figure 10. In-Circuit wiring diagram for MC9S12H-Family 112-PIN LQFP Package
- Figure 11. In-Circuit wiring diagram for MC9S12H-Family 144-PIN LQFP Package
is some
Only Bulk
solved by
this key a Backdoor Access Key disabled there is no
possibilities to disable security. To solve this problem the second method of security disabling
must b
Chip mode below:
when link with MCU completed it is necessarily to read all FLASH and
ore information see sections 5.1.3 On-
ave EEPROM and
ce panel. Also, press
rmanent green light, erasing
solder it back to board.
Figure 2).
rom Motorola device socket (see Figure 1).
are (“Device” Button).
e, $7BF0F Address to $FE in Hex Editor. That
e changes in
EEPROM and FLASH areas are possible.
If furth
Press “
Press “
LED D
regulat
When
comple
If some errors appeared during programming process refer to Section 7.
& Note: There is no way to restore EEPROM and FLASH contents after erasing.
That is strongly recommended read EEPROM and FLASH contents and save it
to file before erasing.
& Note: When target MCU mounted on adaptor check contacts careful to avoid
short circuit. Otherwise target MCU can be damaged!
& Note: During removing the adaptor with target MCU HC912-Programmer must
be powered off to avoid damaging of programmer and target MCU!
problem exists with running of Sector Erase and Program Commands when MCU secured.
Erase of FLASH and EEPROM command possible. In many cases this problem can be
disabling of security via Backdoor Access Key. HC912-Programmer automatically read
nd passes the security sequence. But if
e used. After erasing FLASH and EEPROM, target MCU can be accessed in Special Single
(HC912-Programmer In-Circuit interface). Follow instructions
Read full EEPROM and FLASH contents in On-Board programming interface.
First of all,
EEPROM contents and save it to File. For m
Board EEPROM/FLASH reading example. It is obligatory to s
FLASH contents to file (see Section 6.2).
Erase EEPROM and FLASH.
Press Erase FLASH and EEPROM buttons on Program Sequen
Verify EEPROM and FLASH buttons to perform erase check.
Press Start button.
When LED D1 on HC912-Programmer became pe
completed.
Disconnect power from HC912-Programmer.
Remove target MCU from programmer and
Prepare target MCU for In-Circuit Programming.
Connect required pins to board with target MCU (see Appendix
Remove any adaptor f
Apply power to HC912-Programmer. LED D1 became to green light (see Table 1).
Select corresponding device in HC912-Programmer softw
Load EEPROM/FLASH data from previous saved file.
Change value of FLASH Security byt
mean that device will be unsecured after programming. Also, som
er access to MCU is not required, FLASH Security byte not need to be changed.
EEPROM/FLASH” button on Program Sequence Panel.
Start” button.
4 on HC912-Programmer became to green light. That means that +5 voltage
or switched on and VCC applied to target MCU.
LED D1 on HC912-Programmer became permanent green, programming
ted. Target MCU powered off.
©ETL 2004-2006 MC68HC912/9S12 Programmer User’s Guide 10