Specifications

ManualsBrandsMotorola ManualsCell PhoneMC9190-G

MC9190-G

Integrator Guide

Summary of content (190 pages)

PAGE 1
MC9190-G Integrator Guide
PAGE 2
PAGE 3
MC9190-G Integrator Guide 72E-140937-01 Rev A February 2011
PAGE 4
ii MC9190-G Integrator Guide © 2011 by Motorola Solutions, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
PAGE 5
iii Revision History Changes to the original manual are listed below: Change Rev A Date 02/4/11 Description Initial release.
PAGE 6
iv MC9190-G Integrator Guide
PAGE 7
Table of Contents Revision History.................................................................................................................................... iii About This Guide Introduction ........................................................................................................................................... Documentation Set ......................................................................................................................... Configurations................
PAGE 8
vi MC9190-G Integrator Guide Turning Off the Radios ......................................................................................................................... On Devices with Mobile 6.5 ........................................................................................................... On Device with CE 6.0 ................................................................................................................... WLAN Radio ....................................................
PAGE 9
Table of Contents Configuring the MC9190-G for the Modem (Windows Mobile 6.5) ................................................ Configuring the MC9190-G for the Modem (Windows CE 6.0) ...................................................... Connecting the Modem (Windows Mobile 6.5) .............................................................................. Connecting the Modem (Windows CE 6.0) ....................................................................................
PAGE 10
viii MC9190-G Integrator Guide Working with FFS Partitions ........................................................................................................... RegMerge.dll .................................................................................................................................. CopyFiles ....................................................................................................................................... Non-FFS Partitions ..................................
PAGE 11
Table of Contents Update Loader Image .................................................................................................................... Download Update Loader Package ......................................................................................... ActiveSync ............................................................................................................................... SD Card ........................................................................................
PAGE 12
x MC9190-G Integrator Guide Appendix A: Technical Specifications MC9190-G Specifications .................................................................................................................... Decode Zones ................................................................................................................................ SE960 Standard Range Laser Decode Zones ............................................................................... SE1524 Long Range Laser Decode Zones .....
PAGE 13
Table of Contents Appendix C: Special Software Configurations Bluetooth Configuration Setting ........................................................................................................... Sample Applications and StartUpCtl Configuration ............................................................................. StartUpCtl Application Configuration .............................................................................................
PAGE 14
xii MC9190-G Integrator Guide
PAGE 15
About This Guide Introduction This guide provides information about setting up and configuring the MC9190-G and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation set for the MC9190-G is divided into guides that provide information for specific user needs. • MC9190-G User Guide - describes how to use the MC9190-G. • MC9190-G Integrator Guide - describes how to set up the MC9190-G and the accessories.
PAGE 16
xiv MC9190-G Integrator Guide Software Versions This guide covers various software configurations and references are made to operating system or software versions for: • Adaptation Kit Update (AKU) version • OEM version • BTExplorer version • Fusion version. AKU Version for Mobile 6.5 Devices To determine the Adaptation Kit Update (AKU) version on a Mobile 6.5 device: Tap Start > Settings > System tab > About icon > Version tab. The second line lists the operating system version and the build number.
PAGE 17
About This Guide xv Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started, provides information on setting up the MC9190-G. • Chapter 2, Accessories, describes the accessories available for the MC9190-G and how to set up power connections and battery charging capabilities, where applicable. • Chapter 3, Synchronization, provides instructions on installing ActiveSync and setting up a partnership between the MC9190-G and a host computer.
PAGE 18
xvi MC9190-G Integrator Guide • Bullets (•) indicate: • Action items • Lists of alternatives • Lists of required steps that are not necessarily sequential. • Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists. Related Documents and Software The following documents provide more information about the MC9190-G.
PAGE 19
Chapter 1 Getting Started Introduction This chapter provides information for setting up the MC9190-G. Unpacking the MC9190-G Carefully remove all protective material from around the MC9190-G and save the shipping container for later storage and shipping. Verify that you received all equipment listed below: • MC9190-G • lithium-ion battery • strap, attached to the MC9190-G • stylus, in the stylus silo • Regulatory Guide • Quick Start Guide. Inspect the equipment for damage.
PAGE 20
1-2 MC9190-G Integrator Guide Resetting the MC9190-G Windows CE 6.0 Devices There are two reset functions, warm boot and cold boot. A warm boot restarts the MC9190-G by closing all running programs. A cold boot also restarts the MC9190-G, but erases all stored records and entries in RAM. Data saved in flash memory or a memory card is not lost. In addition it returns formats, preferences and other settings to the factory default settings. Perform a warm boot first.
PAGE 21
Getting Started 1-3 Data saved in flash memory or a memory card is not lost. Perform a warm boot first. This restarts the MC9190-G and saves all stored records and entries. If the MC9190-G still does not respond, perform a cold boot. Performing a Warm Boot Hold down the Power button for approximately five seconds. As soon as the MC9190-G starts to perform a warm boot release the Power button. Performing a Cold Boot A cold boot restarts the MC9190-G.
PAGE 22
1-4 MC9190-G Integrator Guide Battery Management Battery Saving Tips • Leave the MC9190-G connected to AC power at all times when not in use. • Set the MC9190-G to turn off after a short period of non-use. • Set the display to turn off or dim the backlight. • Set the keyboard backlight to turn off after a short period of non-use. • Turn off all wireless radio activity when not in use. • Power off the MC9190-G when charging to charge at a faster rate.
PAGE 23
Getting Started 1-5 Changing the Keypad Backlight Settings To change the keypad backlight settings in order to conserve more battery power: 1. On devices with Windows CE 6.0, tap Start > Settings > Control Panel > Keylight icon > Battery Power tab. or On devices with Windows Mobile 6.5, tap Start > Settings > System > Keylight > Battery Power. 2. Select the On battery power: Disable keylight if not used for: check box and select a value from the drop-down list box. 3. Tap the Advanced. 4.
PAGE 24
1-6 MC9190-G Integrator Guide On Device with CE 6.0 WLAN Radio To turn off the WLAN radio, tap the Wireless Connection Status icon on the task tray and select Disable Radio. A red X appears across the icon indicating that the radio is disabled (off). Wireless Connection Status Icon Figure 1-2 Wireless Connection Status Icon To turn the radio back on, tap the Wireless Connection Status icon on the task tray and select Enable Radio.
PAGE 25
Chapter 2 Accessories Introduction Table 2-1 lists the accessories available for the MC9190-G. Table 2-1 MC9190-G Accessories Accessory Part Number Description Cradles Single Slot Serial/USB Cradle CRD9000-1001SR Charges the MC9190-G main battery and a spare battery. It also synchronizes the MC9190-G with a host computer through either a serial or a USB connection. Four Slot Charge Only Cradle CHS9000-4001CR Charges the MC9190-G main battery.
PAGE 26
2-2 MC9190-G Integrator Guide Table 2-1 MC9190-G Accessories Accessory Part Number Description 24 Volt Auto Charge Cable VCA9000-24R Plugs into a 24 volt cigarette lighter to charge the MC9190-G while on the road. Spare lithium-ion battery KT-21-61261-01 Replacement battery. UBC Adapter Power Supply Kit KT-32665-02R Provides power to the UBC adapter. Power Supply KT-14000-148R Provides power to the Single Slot Serial/USB cradle. 100 - 240 VAC input, 12 VDC 3.33 A output.
PAGE 27
Accessories 2-3 Table 2-1 MC9190-G Accessories Accessory Part Number Description Protective Boot 11-67218-04R Provides additional protection for MC90XX-G configurations. Shoulder Strap 58-40000-007R Universal shoulder strap for holster. Cable Adapter Module (CAM) ADP9000-110R Attaches to the bottom of the MC9190-G and provides power (5 VDC 350 mA) for use with the LS3408ER scanner.
PAGE 28
2-4 MC9190-G Integrator Guide Keypads The MC9190-G has interchangeable modular keypads. The modular keypads can be changed in the field as necessary to support specialized applications. NOTE Do not remove the keypad while the MC9190-G is on and do not operate the MC9190-G with the keypad detached. Follow proper Electro-Static Discharge (ESD) precautions to avoid damaging the SD card.
PAGE 29
Accessories 2-5 Figure 2-2 Installing the Keypad 4. Perform a warm boot. Secure Device (SD) Card The SD card provides secondary non-volatile storage. The SD card is located under the keypad (see Figure 2-1). CAUTION Do not remove the keypad while the MC9190-G is on and do not operate the MC9190-G with the keypad detached. Follow proper ESD precautions to avoid damaging the SD card.
PAGE 30
2-6 MC9190-G Integrator Guide SD Card SD Card Retaining Door Figure 2-3 Inserting the SD Card CAUTION Do not apply more than 4 in-lbs of torque when tightening the keypad screws. 6. Replace the keypad and re-attach using the two screws (see Figure 2-2 on page 2-5). 7. Perform a warm boot.
PAGE 31
Accessories 2-7 Single Slot Serial/USB Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1. This section describes how to set up and use a single Single Slot Serial/USB cradle with the MC9190-G. For serial and USB communication setup procedures see Serial Communication Setup on page 2-34.
PAGE 32
2-8 MC9190-G Integrator Guide • Charges the MC9190-G’s battery. • Charges a spare battery. Setup NOTE The cradle requires a dedicated port on the host. Select either serial or USB for communications. Do not connect the cradle to both serial and USB ports.
PAGE 33
Accessories 2-9 Battery Charging Indicators The Single Slot Serial/USB Cradle can charge the MC9190-G main battery and a spare battery simultaneously. The MC9190-G’s amber charge LED, located in the Indicator LED Bar, shows the status of the battery charging in the MC9190-G. See Table 2-2 for charging status indications. The amber spare battery charging LED on the cradle (see Figure 2-4 on page 2-7) shows the status of the spare battery charging in the cradle.
PAGE 34
2 - 10 MC9190-G Integrator Guide Four Slot Ethernet Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1. This section describes how to set up and use a Four Slot Ethernet cradle with the MC9190-G. For cradle communication setup procedures see Ethernet Communication Setup on page 2-12. Communication LED Figure 2-7 Four Slot Ethernet Cradle CAUTION Do not place coins, keys or paper clips in cradle well.
PAGE 35
Accessories 2 - 11 Table 2-4 Communication LED Status Indication Off MC9190-G is not in cradle; MC9190-G not placed correctly; cradle is not powered. Solid Red MC9190-G is present, but communication has not started. Flashing Green MC9190-G is in the cradle, and communicating with the host computer. Slow Flashing Red Error, communication did not start. Fast Flashing Red Warning: Terminal inactivity time-out.
PAGE 36
2 - 12 MC9190-G Integrator Guide Ethernet Communication Setup To establish a connection between the MC9190-G and the host computer to communicate over an Ethernet network, perform the following: • Install MobileDox Cradle Manager • Install iDockIt • Configure the MC9190-G • Configure the host computer • Configure the DHCP server • Configure the cradle. Installing MobileDox Cradle Manager NOTE MobileDox Cradle Manager is used only when establishing a connection using the Four Slot Ethernet cradle.
PAGE 37
Accessories 2 - 13 • The ability to disable WLAN connection on the device to ensure synchronization is performed via dock. • Management of multiple connection types without losing settings. To install iDockIt on the MC9190-G download the latest version of the iDockIt software from http://www.supportcentral.motorola.com to the host computer. Follow the instructions provided with the iDockIt software to install iDockIt onto the MC9190-G.
PAGE 38
2 - 14 MC9190-G Integrator Guide Figure 2-9 Set IP Address Window 3. Enter the appropriate MAC Address and IP address. 4. Click OK. Modifying Cradle Settings 1. Launch the MobileDox Cradle Manager on the host computer. 2. Select the name of the cradle you want to configure from the list. 3. Click Device > Modify Settings. 4. Use the General Settings tab to modify the identification settings of the cradle.
PAGE 39
Accessories 2 - 15 Table 2-5 Cradle Settings - General Settings Fields Field Description Device Name A text string used to describe the MobileDox device. Any 15-character string may be entered. Custom String A text string for any desired usage (examples are: location, asset ID, etc.). Any 15-character string may be entered. Require Admin Privileges to Modify Settings check box Selecting this check box requires users to have administrative privileges in order to modify MobileDox settings.
PAGE 40
2 - 16 MC9190-G Integrator Guide Figure 2-12 Cradle Settings Window - Port Settings Tab Table 2-7 Cradle Settings - Port Settings Fields Field Description Port Name A text string used to describe the device attached to the port. Any 15-character string can be entered. You can specify up to four port names, one for each of the cradle’s slots. IP Address The IP address assigned to the cradled device. There should be one IP address per cradle slot.
PAGE 41
Accessories 2 - 17 Four Slot Charge Only Cradle CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1. This section describes how to set up and use a Four Slot Charge Only cradle with the MC9190-G. Figure 2-13 Four Slot Charge Only Cradle CAUTION Do not place coins, keys or paper clips in cradle well. The Four Slot Charge Only cradle: • Provides 12VDC power for operating the MC9190-G.
PAGE 42
2 - 18 MC9190-G Integrator Guide Setup Power Port DC Cable AC Line Cord Power Supply Figure 2-14 Four Slot Charge Only Cradle Power Connection Battery Charging Indicators The MC9190-G’s amber charge LED, located in the Indicator LED Bar, shows the status of the battery charging in the MC9190-G. See Table 2-2 on page 2-9 for charging status indications. The battery usually charges in less than four hours.
PAGE 43
Accessories 2 - 19 Four Slot Spare Battery Charger CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1. This section describes how to set up and use the Four Slot Spare Battery Charger to charge up to four spare batteries.
PAGE 44
2 - 20 MC9190-G Integrator Guide Setup Power Port DC Cable AC Cord Power Supply Figure 2-16 Four Slot Spare Battery Charger Power Connection Spare Battery Charging with the Four Slot Spare Battery Charger 1. Connect the charger to a power source as shown in Figure 2-16. 2. Insert the battery into a spare battery charging slot and gently press down on the battery to ensure proper contact.
PAGE 45
Accessories 2 - 21 Magnetic Stripe Reader This section describes how to set up and use the snap-on MSR with the MC9190-G. The MSR snaps on to the bottom of the MC9190-G and can be easily removed when not in use. Latches Card Reader Slot Pogo Pin Pass-through Connector Latch Grip Communications Port Power Port Figure 2-17 Magnetic Stripe Reader When attached to the MC9190-G, the MSR: • Provides power for operating the MC9190-G, with the appropriate power connection.
PAGE 46
2 - 22 MC9190-G Integrator Guide Attaching and Removing To attach, snap the MSR onto the bottom of the MC9190-G. Latch Grip (one on each side) Figure 2-18 Attaching the MSR To remove, squeeze the latch grips and pull the MSR from the MC9190-G. NOTE Remove the MSR from the bottom of the MC9190-G before using a cradle for charging and communication.
PAGE 47
Accessories 2 - 23 Serial Port To Device Serial/USB Port Figure 2-20 MSR Serial/USB Connection Battery Charging Indicators To charge the MC9190-G’s battery through the MSR, connect the power supply to the MSR (see Figure 2-19 on page 2-22), then attach the MSR to the MC9190-G. The MC9190-G begins charging automatically. NOTE Batteries must be charged within the 32° to 104° F (0° to +40° C) ambient temperature range.
PAGE 48
2 - 24 MC9190-G Integrator Guide 3. Tap Start > 9000 Demo > Test Apps > MSR 9000 or MSR Cameo to start the sample application. 4. Swipe the magnetic stripe card through the MSR, ensuring the magnetic stripe on the card faces the MC9190-G. The card may be swiped in either direction, from left to right or from right to left. For best results, gently press down on the card while swiping to ensure contact with the bottom of the reader.
PAGE 49
Accessories 2 - 25 • Provides serial connection through the serial pass-through port for communication with a serial device, such as a host computer. For communication setup procedures, see Serial Communication Setup on page 2-34. • Provides USB connection through the USB pass-through port for communication with a USB device, such as a host computer. For communication setup procedures, see Serial Communication Setup on page 2-34.
PAGE 50
2 - 26 MC9190-G Integrator Guide Serial Port To Device Serial/USB Port Figure 2-25 CAM Serial Connection Battery Charging Indicators To charge the MC9190-G’s battery through the CAM, connect the power supply to the CAM (see Figure 2-24 on page 2-25), then attach the CAM to the MC9190-G. The MC9190-G begins charging automatically. NOTE Batteries must be charged within the 32° to 104° F (0° to +40° C) ambient temperature range.
PAGE 51
Accessories 2 - 27 Universal Battery Charger (UBC) Adapter CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 8-1. This section describes how to use the UBC adapter to charge a spare battery. The UBC can be used with a power supply as a standalone spare battery charger or it can be used with the four station UBC2000 to provide charging to simultaneously charge up to four spare batteries.
PAGE 52
2 - 28 MC9190-G Integrator Guide Setup DC Cable AC Line Cord Power Supply Figure 2-27 UBC Adapter Power Connection Battery Charging Indicators To charge a spare battery using the UBC adapter, connect the power supply to the UBC (see Figure 2-27 on page 2-28), then insert the spare battery. The spare battery begins charging automatically. The UBC’s charge LEDs (see Figure 2-28)) show the status of the battery charging in the adapter. Table 2-9 shows battery charging status indications.
PAGE 53
Accessories 2 - 29 Table 2-9 UBC Adapter Charge LED Status Indications (Continued) LED Indication Description STANDBY or Flashing-Yellow The battery was deeply discharged and is being trickle charged to bring the voltage up to the operating level. After operating level voltage is achieved the battery charges normally. FAULT Yellow Charging error, check placement of MC9190-G and spare battery. CHARGING Yellow Normal charge.
PAGE 54
2 - 30 MC9190-G Integrator Guide Setup Connecting to the MC9190-G CAM Male 15-pin connector 1 2 4 AB C GH I 7 5 8 HO LD R 3 6 REC ALL MN O TU V 9 0 OPE DE F JKL PR S * FN C WX Y CN F # LNR TR F SPD AN S SP KR Line In port Phone port Phone cord Phone cord Figure 2-30 Modem Module Connection - MC9190-G CAUTION Do not connect the modem's 15-pin connector into a VGA port of a host computer.
PAGE 55
Accessories 2 - 31 Connecting to the Single Slot Serial/USB Cradle Adapter cable Male 15-pin connector Line In port Phone port Phone cord Figure 2-31 Modem Module Connection - Single Slot Serial/USB Cradle CAUTION Do not connect the modem's 15-pin connector into a VGA port of a host computer. NOTE If using a phone, connect the cord from the phone to the Phone port on the modem.
PAGE 56
2 - 32 MC9190-G Integrator Guide 5. Enter the access phone number in the My Connection window and tap Next. 6. If necessary, enter the user name, password and domain. 7. Tap Advanced... to set TCP/IP and server information, if required. 8. Tap OK to exit the Advanced window. 9. Tap Finish. Configuring the MC9190-G for the Modem (Windows CE 6.0) To create a modem connection on the MC9190-G: 1. Connect the modem to the MC9190-G, see Connecting to the MC9190-G on page 2-30. 2.
PAGE 57
Accessories 2 - 33 1. On the MC9190-G, tap Settings >Control Panel. Double-tap the Network and Dial-up Connections icon. 2. In the Connection window, double-tap the My Connection icon to edit the settings. Figure 2-32 Network and Connections Windows 3. To modify dial-up properties, tap Dial Properties, make the selections in the Device Properties window. 4. To edit the Dialing Patterns, tap Edit. Figure 2-33 Dial-Up and Dial Properties Window 5. The Edit Dialing Patterns window appears.
PAGE 58
2 - 34 MC9190-G Integrator Guide Serial Communication Setup The serial communications setup can be used to set up to communicate with a Single Slot Serial/USB Cradle, MSR or a CAM. NOTE For serial communication using accessories that can communicate with either a serial or USB connection, connect only the serial cable. Do not connect both the serial and USB cables.
PAGE 59
Accessories 2 - 35 11. Ensure the accessory being used to communicate is connected to the host computer and the appropriate power source. NOTE The accessory requires a dedicated port. It cannot share a port with any other device. Refer to the host computer user manual supplied to locate the USB ports. 12. Connect the MC9190-G to the accessory being used for communication. 13. Power on the MC9190-G. 14.
PAGE 60
2 - 36 MC9190-G Integrator Guide Figure 2-37 Connection Settings 9. For a serial connection, select Allow connections to one of the following: check box and select the comm port from the drop-down list. 10. For USB connection, select Allow USB connection check box. 11. Tap OK to save any changes made. NOTE Every MC9190-G should have a unique device name. Never try to synchronize more than one MC9190-G to the same name. 12. Connect the device to the host computer.
PAGE 61
Accessories 2 - 37 USB Host Communication Setup NOTE USB Host mode is only available on Windows Mobile devices. The MC9190-G can be configured as a USB host device for use with USB client devices. To configure the MC9190-G as a USB host: 1. Tap Start > Settings > System > USBConfig. 2. Tap the USB Host Mode radio button. 3. Tap OK. NOTE When the MC9190-G is configured a a USB host, it cannot ActiveSync with a host computer. To configure the MC9190-G as a USB client: 1.
PAGE 62
2 - 38 MC9190-G Integrator Guide Wall Mounting Bracket and Shelf Slide This section describes how to install and set up the MC9000 Wall Mount Bracket and Shelf Slide to mount cradles to a wall. Wall Mounting Bracket Shelf Slides Mounts one single slot cradle Mounts two single slot cradles Figure 2-38 Wall Mounting Bracket with Shelf Slide When installed on a wall, the mounting bracket and shelf slide enable mounting one or two single slot cradles to a wall. Use two brackets to mount a four slot cradle.
PAGE 63
Accessories 2 - 39 Insert screws Insert screws Figure 2-40 Wall Mounting Bracket Mounting Screws If using the bracket and slide with a four slot cradle, secure a second bracket to the wall next to the first, aligning the horizontal screw holes on the second with those of the first. Attaching the Shelf Slide to the Wall Mount Bracket One Single Slot Cradle/Four Slot Battery Charger To attach the shelf slide to the wall mount bracket for use with one single slot cradle or four slot battery charger: 1.
PAGE 64
2 - 40 MC9190-G Integrator Guide Pan-head screw holes Insert screws from below Figure 2-42 Attaching Two Shelf Slides Four Slot Cradle To attach the shelf slide to the wall mount bracket for use with a four slot cradle: 1. Place a slide on the left-hand bracket, aligning the larger pan-head screw holes in the slide with the left two screw holes on the bracket. 2.
PAGE 65
Accessories 2 - 41 Insert set screws Figure 2-44 Attaching Two Shelf Slides For a four slot cradle, slide the cradle on to the slides, across both brackets. Secure each cradle or charger to its slide using the two set screws provided.
PAGE 66
2 - 42 MC9190-G Integrator Guide
PAGE 67
Chapter 3 Synchronization Introduction Synchronization lets the user manage information between an MC9190-G and a host computer so that changes made either on the MC9190-G or on the host computer appear in both places. Download and install sync software to the host computer (either Microsoft ActiveSync for Windows XP or Windows Mobile Device Center (WMDC) for Windows Vista and Windows 7) in order to use the sync feature. Visit www.microsoft.com on the host computer for details.
PAGE 68
3-2 MC9190-G Integrator Guide MC9190-G Setup NOTE Microsoft recommends installing the sync software on the host computer before connecting the MC9190-G. The MC9190-G can be set up to communicate with a USB connection. The MC9190-G communication settings must be set to match the communication settings used with ActiveSync or WMDC. On Window CE 6.0 devices: 1. On the MC9190-G tap Start > Settings > Control Panel > PC Connection. The PC Connection Properties window appears.
PAGE 69
ActiveSync 3-3 Figure 3-2 ActiveSync Window NOTE Assign each MC9190-G a unique device name. Do not try to synchronize more than one MC9190-G to the same name. 2. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears. Figure 3-3 Connection Settings Window 3. Select Allow USB connections check box. 4. Select the Show status icon in taskbar check box. 5. Select OK to save any changes made. Windows Mobile Device Center 1.
PAGE 70
3-4 MC9190-G Integrator Guide Figure 3-4 Windows Mobile Device Center Window 2. In the WMDC window, under Mobile Device Settings, click Connection settings. Figure 3-5 Connection Settings Window 3. Select Allow USB connections and adjust any additional settings as needed. 4. Click OK to save your settings. Setting up a Partnership with a Windows CE 6.0 Device To set up a partnership with a Windows CE 6.0 device: 1.
PAGE 71
ActiveSync ActiveSync WMDC Figure 3-6 Select Synchronization Setting Window 4. Select the appropriate settings and click Next. ActiveSync Figure 3-7 Setup Complete Window 5. Click Finish or Setup.
PAGE 72
3-6 MC9190-G Integrator Guide ActiveSync WMDC Figure 3-8 Connected Window During the first synchronization, information stored on the MC9190-G is copied to the host computer. When the copy is complete and all data is synchronized, the MC9190-G can be disconnect from the host computer. NOTE The first synchronization operation must be performed with a local direct connection. To retain partnerships after a cold boot, capture partnership registry information in a .
PAGE 73
ActiveSync ActiveSync WMDC Figure 3-9 Select Synchronization Settings 6. Select the appropriate settings and click Next. ActiveSync Figure 3-10 Setup Complete Window 7. Click Finish.
PAGE 74
3-8 MC9190-G Integrator Guide ActiveSync WMDC Figure 3-11 Connected Window During the first synchronization, information stored on the MC9190-G is copied to the host computer. When the copy is complete and all data is synchronized, the MC9190-G can be disconnected from the host computer. NOTE The first synchronization operation must be performed with a local direct connection. Windows Mobile retains partnerships information after a cold boot.
PAGE 75
Chapter 4 Wireless Applications Introduction Wireless Local Area Networks (LANs) allow the MC9190-G to communicate wirelessly and send captured data to a host device in real time. Before using the MC9190-G on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the MC9190-G must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware. NOTE 802.11d is enabled by default.
PAGE 76
4-2 MC9190-G Integrator Guide Signal Strength Icon Figure 4-1 Wireless Application Menu Windows Mobile 6.5 Devices The interface to the Signal Strength icon and Wireless Launcher has changed in the Windows Mobile 6.5 default Today screen. To view the Wireless Launcher, select the Fusion plug-in on the Today screen and tap the Fusion Menu soft key. Figure 4-2 Fusion Plug-in on Today Screen Functionality of this dialog is similar to the Wireless Launch menu.
PAGE 77
Wireless Applications 4-3 Figure 4-3 Wireless Launcher Window Fusion Applications Many of the items in the menu invoke one of the Fusion applications. These menu items and their corresponding applications are summarized below: • Find WLANs – Invokes the Find WLANs application which displays a list of the WLANs active in your area.
PAGE 78
4-4 MC9190-G Integrator Guide Table 4-1 Signal Strength Icons Descriptions Icon None Status Description Excellent signal strength WLAN network is ready to use. Very good signal strength WLAN network is ready to use. Good signal strength WLAN network is ready to use. Fair signal strength WLAN network is ready to use. Notify the network administrator that the signal strength is only “Fair”. Poor signal strength WLAN network is ready to use. Performance may not be optimum.
PAGE 79
Wireless Applications Figure 4-5 Opening Wireless Manager Select Wireless Manager. To enable or disable the WLAN radio, tap the Wi-Fi bar.
PAGE 80
4-6 MC9190-G Integrator Guide
PAGE 81
Chapter 5 Application Deployment for Windows CE Introduction This chapter describes new features in Windows CE 6.0 including how to package applications, and procedures for deploying applications onto the MC9190-G. Packaging Packaging combines an application's executable files into a single file, called a package. This makes it easier to deploy and install an application to the MC9190-G. Package new applications and updates, such as new DLL files, as CAB files, then deploy them to the MC9190-G.
PAGE 82
5-2 MC9190-G Integrator Guide • If developing applications for Windows Mobile 6.5 or Windows CE 6.0 • Microsoft® Visual Studio 2005 • Microsoft® Visual Studio 2005 Service Pack1 (or) • Microsoft® Visual Studio 2008 • Microsoft® Visual Studio 2008 Service Pack1 • One or more of the following Platform SDK's: • Windows Mobile 6 Professional and Standard Software Development Kits Refresh • For Windows CE embedded development use the Motorola Platform SDK (PSDK) for your specific device.
PAGE 83
Application Deployment for Windows CE 5-3 NOTE If both Microsoft Visual C++ v3.0 and Microsoft Visual C++ v4.0 are installed on the development computer, ensure Microsoft Visual C++ v4.0 launches. Installing Other Development Software Developing applications for the MC9190-G may require installing other development software, such as application development environments, on the development PC. Follow the installation instructions provided with the software.
PAGE 84
5-4 MC9190-G Integrator Guide RegMerge.dll RegMerge.dll is a built-in driver that allows registry edits to be made to the Windows CE registry. Regmerge.dll runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders during a cold boot. It then merges the registry changes into the system registry located in RAM.
PAGE 85
Application Deployment for Windows CE 5-5 • Windows CE: The complete Windows CE operating system is stored on Flash devices. If necessary, the entire OS image may be downloaded to the MC9190-G using files provided by Motorola. Any upgrades must be obtained from Motorola. This partition is mandatory for the MC9190-G. • Splash Screen: a bitmap smaller than 16 Kb (and limited to 16 bits per pixel) is displayed as the MC9190-G cold boots.
PAGE 86
5-6 MC9190-G Integrator Guide Deployment This section provides information about installing software and files on the MC9190-G. Software deployment can be performed by: • Copying files from a host computer • Installing programs • Updating images. Copying Files from a Host Computer To copy files from a host computer to the MC9190-G: 1. Ensure that ActiveSync or Windows Mobile Device Center is installed on the host computer and that a partnership was created.
PAGE 87
Application Deployment for Windows CE 5-7 Figure 5-2 ActiveSync Explorer 5. Double-click the folder to expand the folder contents. Figure 5-3 Application Folder Contents 6. Use Explorer to locate the host computer directory that contains the file to download. Tap that directory in the left pane to display its contents in the right pane. 7. Drag the desired file(s) from the host computer to the desired mobile device folder.
PAGE 88
5-8 MC9190-G Integrator Guide 5. Double-click the executable file on the host computer. If the file is an installer, the installation wizard begins. Follow the directions on the window. Once the software is installed on the host computer, the installer transfers the software to the MC9190-G. If the file is not an installer, an error message states that the program is valid but is designed for a different type of computer. Copy this file to the MC9190-G.
PAGE 89
Application Deployment for Windows CE 7. Double tap on the file: 9100c60Ben_TEMP.lnk. 8. When the OS Update application finds the appropriate file, it loads the package onto the MC9190-G. A progress bar displays until the update completes. 9. When complete, the MC9190-G re-boots and the calibration screen appears. Using an SD Card To initiate an update using an SD card: 1. Go to the Support Central web site, http://supportcentral.motorola.com. 2. Download the appropriate update package. 3.
PAGE 90
5 - 10 MC9190-G Integrator Guide 9. When the Bootloader screen appears, release the trigger. Select required operation Download from SD card Download from USB Exit Figure 5-4 Bootloader Menu CAUTION To ensure a successful download, do not remove power from the MC9190-G while in Bootloader. 1. Use the up and down scroll buttons to select Download from SD card, then press Enter. 2. The Bootloader displays the hex files available on the SD card. a:\ All Done 9100c60XenMO06109xx.
PAGE 91
Application Deployment for Windows CE 5 - 11 Splash screen ############# 100% Download complete in - 0.042 seconds (1854142 bytes/second) Hit Enter to Acknowledge - Figure 5-6 Download Complete Screen 5. On completion, press ENTER to return to the Bootloader menu to select the next file to download. 6. To exit Bootloader, select Exit from the Bootloader main screen and press ENTER.
PAGE 92
5 - 12 MC9190-G Integrator Guide Select required operation Download from SD card Download from USB Exit Figure 5-8 Bootloader Screen CAUTION To ensure a successful download, do not remove power from the MC9190-G while in Bootloader. 8. Place the MC9190-G into a Single Slot Serial/USB Cradle. 9. Use the up and down scroll buttons to select Download from USB, then press ENTER. 10. The Bootloader displays the following: Waiting for input. . . Figure 5-9 Waiting for Input 11.
PAGE 93
Application Deployment for Windows CE 5 - 13 Figure 5-10 Select Source File Window 12. Select the hex files and the click Open. 13. Click the SEND DATA button. The hex file is downloaded to the MC9190-G. Splash screen ##########) 100% Download complete in - 0.042 seconds (1854142 bytes/second) Hit Enter to Acknowledge Figure 5-11 Download Complete Screen 14. On completion, press ENTER to return to the Bootloader main screen to select the next file to download. 15.
PAGE 94
5 - 14 MC9190-G Integrator Guide To find the probable cause of the error, use the error number and/or the error text displayed on the screen to look up the error in Table 5-1. Table 5-1 Bootloader Errors Error Text Error Number Probable Cause Unknown error -1 A general error occurred. Retry the download. If the failure persists, it is most likely due to a hardware failure; the MC9190-G requires servicing. Cancelled by user -2 The user cancelled the download.
PAGE 95
Application Deployment for Windows CE 5 - 15 Table 5-1 Bootloader Errors (Continued) Error Text Error Number Probable Cause Invalid data in HEX file -25 The HEX file being downloaded contains invalid data. Ensure the file is in proper HEX file format with valid HEX data. Exceeded max size -26 The download file is too large to fit into the space allocated for it. Either make the file smaller or increase the space allocated for it by altering the partition table.
PAGE 96
5 - 16 MC9190-G Integrator Guide Creating a Splash Screen A custom splash screen can be created and loaded onto the MC9190-G. To create a custom splash screen: 1. Create a .bmp file using a graphic program with the following specifications: • Size: 296 H x 240 H. • Colors: 16 bits per pixel (65536 colors). 2. Modify the bitmap file and save. To load the splash screen on the MC9190-G Windows CE device: 1. Convert the bmp file into a hex file using the OSUpdate Package Builder that is part of MSP. 2.
PAGE 97
Chapter 6 Application Deployment for Windows Mobiles Introduction This chapter describes new features in Windows Mobile 6.5 including new security features, how to package applications, and procedures for deploying applications onto the MC9190-G. Security The MC9190-G implement a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust.
PAGE 98
6-2 MC9190-G Integrator Guide mode. This means that only applications signed with a certificate from the Privileged Execution Trust Certificate Store can run. To support the broadest number of deployments, third-party software developers should perform the following when releasing software for a Windows Mobile 6.
PAGE 99
Application Deployment for Windows Mobile 6-3 Installing Certificates Use XML provisioning to query and delete certificates from certificate stores.
PAGE 100
6-4 MC9190-G Integrator Guide may not work properly. Refer to the Windows Mobile Version 6 Help file for finding information on Remote API security policies. XML Provisioning To configure the settings on an MC9190-G, use XML provisioning. To install an XML provisioning file on the MC9190-G, create a Cabinet Provisioning File (CPF). A CPF file is similar to a CAB file and contains just one file: _setup.xml. Like a CAB file, the CPF extension is associated with WCELoad.EXE.
PAGE 101
Application Deployment for Windows Mobile 6-5 RegMerge RegMerge.dll is a built-in driver that allows updating the registry during a clean boot. RegMerge runs very early in the boot process and looks for registry files (.reg files) in certain Flash File System folders (i.e., \Application) during a clean boot. It then merges the registry changes into the system registry located in RAM. The following example uses RegMerge to set a registry key: SampleReg.
PAGE 102
6-6 MC9190-G Integrator Guide SampleCpy.xml
PAGE 103
Application Deployment for Windows Mobile 6-7 EMDK for C To download and install the EMDK for C: 1. Download the EMDK from the Support Central web site, http://supportcentral.motorola.com. a. Select Mobile Computers. The MC9190-G Product page displays. b. Select MC9190-G. The MC9190-G Product page displays. c. On the MC9190-G Product page, select the appropriate Enterprise Mobility Developer Kit for C from the Software Downloads section. The Enterprise Mobility Developer Kit for C page displays. d.
PAGE 104
6-8 MC9190-G Integrator Guide Volatile File Storage (Cache Disk) Windows Mobile 6.5 memory architecture uses persistent storage for all files, registry settings, and database objects to ensure data is retained even after a power failure. Persistent storage is implemented using Flash memory technology which is generally slower than volatile RAM memory. In certain situations the speed of the operation is more important than the integrity of the data.
PAGE 105
Application Deployment for Windows Mobile Refer to the Microsoft Windows Mobile 6 Help file for information on CAB files. Installation Using ActiveSync To install an application package: • Connect the MC9190-G to a host computer using ActiveSync. See Chapter 3, Synchronization for more information. • Locate the package file on the host computer. • In ActiveSync on the host computer, open Explorer for the MC9190-G. • Copy the CAB file from the host computer to the \temp directory on the MC9190-G.
PAGE 106
6 - 10 MC9190-G Integrator Guide 4. Select the Mass Storage checkbox. 5. In the drop-down list, select either \Storage Card, \Application or \Cache Disk. 6. Tap OK. 7. Connect the MC9190-G to a host computer using either a single slot cradle or a USB cable. 8. On the host computer, open Windows Explorer. The MC9190-G appears as a hard disk drive in Windows Explorer. 9. Double-click the drive letter to open the folder. 10.
PAGE 107
Application Deployment for Windows Mobile 6 - 11 ActiveSync To install an update loader package using ActiveSync: 1. Connect the MC9190-G to a host computer using ActiveSync. See Chapter 3, Synchronization for more information. 2. In ActiveSync on the host computer, open Explorer for the MC9190-G. 3. Copy all the update loader package files from the host computer to the \temp directory on the MC9190-G. 4. On the MC9190-G, navigate to the \temp directory. 5.
PAGE 108
6 - 12 MC9190-G Integrator Guide To load the splash screen on the MC9190-G: 1. Create a text file named pkgs.lst which contains the name of the bmp file. For example, mysplash.bmp. 2. Copy the bmp file and the pkgs.lst file to one of the following: • SD card root directory • MC9190-G’s \temp directory. 3. If using the SD card, insert the SD card into the MC9190-G. 4. Perform a cold boot. 5.
PAGE 109
Chapter 7 Interactive Sensor Technology Configuration Introduction This chapter provides information for configuring the Interactive Sensor Technology (IST) settings. IST settings can be accessed: • On Windows Mobile, tap Start > Settings > System > IST Settings. • On Windows CE, tap the IST Settings icon in the Task Tray. IST Menu On Windows CE, tap the IST Settings icon to open the menu. This menu lists IST configuration settings.
PAGE 110
7-2 MC9190-G Integrator Guide Table 7-1 IST Tray Icon Menu Items Menu Item Description Configure IST Opens the IST Settings window. Hide Removes IST Settings icon from the Command bar. Wake Up On Motion Wakes the MC9190-G from suspend mode if it was placed in suspend mode due to inactivity. Keep Alive On Motion Prevents going into suspend mode motion is detected. See Keep Alive On Motion on page 7-3 for more information. Auto Display Orientation Enables auto display orientation.
PAGE 111
Interactive Sensor Technology Configuration 7-3 Table 7-2 IST General Tab Information Item Status Description Displays status information of the IST device. If the IST is not working properly it displays the error message. Device working Properly - Normal state. IST Hardware not present - When there is no response from IST hardware. Please contact service department. Need calibration - Device is not calibrated. Contact your system administrator.
PAGE 112
7-4 MC9190-G Integrator Guide Wake Up on Motion The Wake Up on Motion section provides configurable options for waking the MC9190-G from suspend mode by shaking the MC9190-G. Select Inactivity checkbox to allow IST to wake the MC9190-G when it was suspended due to inactivity. Use the Change Sensitivity… button to configure the sensitivity settings. Setting Sensitivity Use the slider to set the sensitivity.
PAGE 113
Interactive Sensor Technology Configuration 7-5 Event Log Tab Use the Event Log tab to display the event details. This feature in IST mainly focuses on abuse by dropping the device. Figure 7-6 Event Log Tab The Motion Event Summery list displays a summary of the event report. To view the full report tap the Motion Event Details… button. Use the Audible Notification panel to enable playing of a wave file when the MC9190-G is dropped. Select a desired .wav file from the Sounds: drop-down list.
PAGE 114
7-6 MC9190-G Integrator Guide
PAGE 115
Chapter 8 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC9190-G, and provides troubleshooting solutions for potential problems during MC9190-G operating. Maintaining the MC9190-G For trouble-free service, observe the following tips when using the MC9190-G: • Take care not to scratch the screen of the MC9190-G. When working with the MC9190-G, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
PAGE 116
8-2 MC9190-G Integrator Guide • To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF (0 ºC and +40 ºC) • Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Enterprise Mobility support.
PAGE 117
Maintenance & Troubleshooting 8-3 Harmful Ingredients The following chemicals are known to damage the plastics on the MC9190-G and should not come in contact with the device: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform. Cleaning Instructions Do not apply liquid directly to the MC9190-G.
PAGE 118
8-4 MC9190-G Integrator Guide 3. Rub the cotton portion of the cotton tipped applicator back-and-forth across the battery contacts on the back of the battery. Do not leave any cotton residue on the contacts. 4. Repeat at least three times. 5. Use the cotton tipped applicator dipped in alcohol to remove any grease and dirt near the contact area. 6. Use a dry cotton tipped applicator and repeat steps 3 through 5. 7.
PAGE 119
Maintenance & Troubleshooting 8-5 Troubleshooting MC9190-G Table 8-1 Troubleshooting the MC9190-G Problem MC9190-G does not turn on. Cause Solution Battery not charged. Charge or replace the battery. Battery not installed properly. Ensure battery is installed properly. System crash. Perform a warm boot. If the MC9190-G still does not turn on, perform a cold boot. See Resetting the MC9190-G on page 1-2. Battery failed. Replace battery.
PAGE 120
8-6 MC9190-G Integrator Guide Table 8-1 Troubleshooting the MC9190-G (Continued) Problem MC9190-G turns itself off. Cause Solution MC9190-G is inactive. The MC9190-G turns off after a period of inactivity. If the MC9190-G is running on battery power, this period can be set to 30 sec., 1, 2, 3, 4, 5 or 6 minutes. If the MC9190-G is running on external power, this period can be set to 1, 2, 3, 5, 10, 15 and 30 minutes. For Windows Mobile 6.
PAGE 121
Maintenance & Troubleshooting 8-7 Table 8-1 Troubleshooting the MC9190-G (Continued) Problem The MC9190-G does not accept scan input. Cause Solution Scanning application is not loaded. Verify that the MC9190-G is loaded with a scanning application. See the System Administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Ensure MC9190-G is within proper scanning range. MC9190-G is not programmed for the bar code.
PAGE 122
8-8 MC9190-G Integrator Guide Four Slot Charge Only Cradle Table 8-3 Troubleshooting the Four Slot Charge Only Cradle Problem MC9190-G charge indicator LED does not light. Cause Solution Cradle is not receiving power. Ensure the power supply is securely connected and receiving power. MC9190-G is not seated correctly in the cradle. Ensure the battery is properly installed in the MC9190-G, and re-seat the MC9190-G in the cradle. The battery is not properly installed in the MC9190-G.
PAGE 123
Maintenance & Troubleshooting 8-9 Table 8-4 Troubleshooting the Four Slot Ethernet Cradle (Continued) Symptom All Communication Status LEDs are flashing red. Communication Status LED does not light up. Battery is not recharging. Warning Message - “! Unable to obtain a server assigned IP address. Try again later or enter an IP address in Network Settings.” Cause Solution The cradle could not configure itself, or it has lost the lease on its IP address.
PAGE 124
8 - 10 MC9190-G Integrator Guide Four Slot Spare Battery Charger Table 8-5 Troubleshooting The Four Slot Spare Battery Charger Symptom Batteries not charging. Possible Cause Action Battery was removed from the charger or charger was unplugged from AC power too soon. Ensure the charger is receiving power. Confirm main battery is charging. If a battery is fully depleted, it can take up to four hours to fully recharge a battery. Battery is faulty. Verify that other batteries charge properly.
PAGE 125
Maintenance & Troubleshooting 8 - 11 Table 8-6 Troubleshooting the Single Slot Serial/USB Cradle (Continued) Symptom Possible Cause Action Spare battery is not charging. Battery not fully seated in charging slot. Remove and re-insert the spare battery into the cradle, ensuring it is firmly seated. Battery inserted incorrectly. Ensure the contacts are facing down and toward the back of the cradle. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
PAGE 126
8 - 12 MC9190-G Integrator Guide Table 8-7 Troubleshooting The Cable Adapter Module (Continued) Symptom During data communications, no data was transmitted, or transmitted data was incomplete. Possible Cause Action MC9190-G detached from CAM during communications. Re-attach MC9190-G to CAM and retransmit. Incorrect cable configuration. See the System Administrator. Communications software is not installed or configured properly. Perform setup as described in Chapter 2, Accessories.
PAGE 127
Maintenance & Troubleshooting 8 - 13 Table 8-8 Troubleshooting the Magnetic Stripe Reader (Continued) Symptom During data communications, no data was transmitted, or transmitted data was incomplete. Possible Cause Action MC9190-G detached from MSR during communications. Reattach MC9190-G to MSR and retransmit. Incorrect cable configuration. See the System Administrator. Communications software is not installed or configured properly. Perform setup as described in Chapter 2, Accessories.
PAGE 128
8 - 14 MC9190-G Integrator Guide Table 8-9 Troubleshooting the Modem Module (Continued) Symptom ActiveSync fails. Dial-out fails Possible Cause Action A partnership was not established with the host computer. Establish a partnership with the host computer (see Chapter 2, Accessories). Host computer is not selected in the ActiveSync window on the MC9190-G. Select a host computer in the ActiveSync window, and perform setup (see Chapter 2, Accessories).
PAGE 129
Appendix A Technical Specifications MC9190-G Specifications The following table summarizes the MC9190-G’s technical specifications. Table A-1 Technical Specifications Item Description Physical and Environmental Characteristics Dimensions 9.1 in. L x 3.6 in. W x 7.6 in. H 23.1 cm L x 9.1 cm H x 19.3 cm H Weight (includes battery, scanner and radio) 709 g (25 oz.) Keyboard 28-key; 43-key; 53-key; Terminal Emulation (5250, 3270, VT) Display 3.7 in. color.
PAGE 130
A-2 MC9190-G Integrator Guide Table A-1 Technical Specifications (Continued) Item Data Capture Options Description SE960: 1D standard range scan engine. SE1524-ER: 1D extended range scan engine reads up to 45 ft./13.72 m away. SE4500-SR: Omnidirectional 1D/2D imaging engine reads 1D and 2D symbols. SE4500-DL: 1D/2D DL imaging engine reads all 1D and 2D codes as well as the PDF codes found on driver’s licenses and other identification documents.
PAGE 131
Technical Specifications A-3 Table A-1 Technical Specifications (Continued) Item Description WLAN Wireless Data Communications WLAN radio 802.11a/b/g. Note: 802.11a not available in Thailand. Output Power 100mW U.S. and International Data Rate 802.11a: up to 54Mb per second 802.11b: up to 11Mb per second 802.11g: up to 54Mb per second Frequency Range All country dependent: 802.11a - 5 GHz; 802.11b – 2.4 GHz; 802.11g – 2.
PAGE 132
A-4 MC9190-G Integrator Guide Table A-2 Data Capture Options Item Laser Decode Capability Description Code 39 Codabar Interleaved 2 of 5 MSI UPC/EAN supplementals Webcode RSS Expanded Code 128 Code 11 EAN-8 UPCA Coupon Code RSS-14 Code 93 Discrete 2 of 5 EAN-13 UPCE Trioptic 39 RSS Limited Chinese 2 of 5 Imaging Decode Capability Code 39 Code 128 Codabar Code 11 Discrete 2 of 5 MSI EAN-13 UPCA UPC/EAN supplementals Coupon Code Webcode TLC39 Composite C Micro PDF-417 Macro PDF-417 (Macro) Micro PDF-4
PAGE 133
Technical Specifications A-5 Decode Zones SE960 Standard Range Laser Decode Zones Figure A-1 shows the decode zone for the SE960 scan engine. The figures are typical values. Table A-3 lists the typical distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. 73.4o Note: Typical performance at on high quality symbols. F (23o 47o Scan Angle 5 mil C128 12.5 7.5 mil 1.1 19.0 100% UPC 1.
PAGE 134
A-6 MC9190-G Integrator Guide Table A-3 SE960 Decode Distances Symbol Density/ Bar Code Type/ W-N Ratio Typical Working Ranges Bar Code Content/ ContrastNote 1 Near Far 5.0 mil Code 128 1234 80% MRD 1.2 in 3.05 cm 7.7 in 19.56 cm 5.0 mil Code 39; 2.5:1 ABCDEFGH 80% MRD 1.2 in 3.05 cm 12.5 in 31.75 cm 7.5 mil Code 39; 2.5:1 ABCDEF 80% MRD 1.1 in 2.79 cm 18.5 in 46.99 cm 10 mil Code 128 1234 80% MRD 1.2 in 3.05 cm Note 3 19.0 in 48.26 cm 13 mil 100% UPC 12345678905 80% MRD 1.6 in 4.
PAGE 135
Technical Specifications A-7 SE1524 Long Range Laser Decode Zones Typical decode ranges are shown in Figure A-2. Table A-4 on page A-8 lists the typical distances for the SE1524 for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. The maximum usable length of a symbol at any given range is shown. in. Note: Typical performance at 73.4°F (23°C) on high quality symbols. W i d t h cm 12 30.5 8 20.
PAGE 136
A-8 MC9190-G Integrator Guide Table A-4 SE 1524 Decode Distances Symbol Density/ p/n / Bar Code Type/ W-N Ratio Typical Working Ranges Bar Code Content/ ContrastNote 1 Near Far 7.5 mil 64-17452-01 Code 39; 2.5:1 ABCDEF 80% MRD 2.0 in 5.08 cm 22.0 in 55.88 cm 10 mil 64-17454-01 Code 39; 2.5:1 ABCDE 80% MRD 4.0 in 10.16 cm 34.0 in 86.36 cm 15 mil 64-17417-01 Code 39; 2.5:1 ABCD 80% MRD 5.0 in 12.70 cm 71.0 in 180.34cm 20 mil 64-17456-01 Code 39; 2.2:1 123 80% MRD 5.0 in 12.70 cm 96.
PAGE 137
Technical Specifications A-9 SE4500 Standard Range Imager Decode Zones SE4500-SR Figure A-3 shows the decode zone for the SE4500-SR. Typical values appear. Table A-3 lists the typical distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. Note: Typical performance at 73˚F (23˚C) on high quality symbols in normal room light. Vcc = 3.3V in. cm 9 22.9 4.5 11.4 0 4.5 11.4 5 mil Code 39 7.
PAGE 138
A - 10 MC9190-G Integrator Guide Table A-5 SE4500-SR Decode Distances Symbol Density/ Bar Code Type Typical Working Ranges Bar Code Content/ ContrastNote 2 Near Far 5.0 mil Code 39 ABCDEFGH 80% MRD 2.1 in 5.33 cm 7.5 in 19.05 cm 6.67 mil PDF417 4 Col, 20 Rows 80% MRD 3.4 in 8.64 cm 7.1 in 18.03 cm 7.5 mil Code 39 ABCDEF 80% MRD Note 1 10.6 in 26.92 cm 10 mil PDF417 3 Col, 17 Rows 80% MRD Note 1 10.1 in 25.65 cm 13 mil UPC-A 012345678905 80% MRD 1.6 in 5.08 cm 15.5 in 39.
PAGE 139
Technical Specifications A - 11 SE4500-DL Figure A-4 shows the decode zone for the SE4500-DL. Typical values appear. Table A-6 lists the typical distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. Note: Typical performance at 73˚F (23˚C) on high quality symbols in normal room light. Vcc = 3.3V 3 mil Code 39 4.2 2.7 5 mil Code 39 1.4 7.3 5 mil PDF417 4.5 2.8 1.9 6.67 mil PDF417 6.9 7.
PAGE 140
A - 12 MC9190-G Integrator Guide Table A-6 SE4500-DL Decode Distances Symbol Density/ Bar Code Type Typical Working Ranges Bar Code Content/ ContrastNote 2 Near Far 3.0 mil Code 39 80% MRD 2.7 in 6.86 cm 4.2 in 10.67 cm 5.0 mil Code 39 ABCDEFGH 80% MRD 1.4 in 3.56 cm 7.3 in 18.54 cm 5.0 mil PDF417 80% MRD 2.8 in 7.11 cm 4.5 in 11.43 cm 6.67 mil PDF417 4 Col, 20 Rows 80% MRD 1.9 in 4.83 cm 6.9 in 17.53 cm 7.5 mil Code 39 ABCDEF 80% MRD Note 1 9.9 in 25.
PAGE 141
Technical Specifications A - 13 SE4500-HD Figure A-5 shows the decode zone for the SE4500-HD. Typical values appear. Table A-7 lists the typical distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. Note: Typical performance at 73°F (23°C) on high quality symbols in normal room light. Vcc = 3.3V in. cm 4.0 10.2 2.0 5.1 0 o f 2.0 5.1 F i e l d 0 3 mil Code 39 1.6 3.
PAGE 142
A - 14 MC9190-G Integrator Guide Table A-7 SE4500-HD Decode Distances Symbol Density/ Bar Code Type Typical Working Ranges Bar Code Content/ ContrastNote 2 Near Far 3.0 mil Code 39 80% MRD 1.6 in 4.06 cm 3.8 in 9.65 cm 4.0 mil PDF417 80% MRD 1.8 in 4.57 cm 3.5 in 8.89 cm 5.0 mil Code 39 ABCDEFGH 80% MRD Note 1 5.0 in 12.70 cm 5.0 mil PDF417 80% MRD 1.6 in 4.06 cm 3.8 in 9.65 cm 5 mil Data Matrix 18 x 18 Modules 80% MRD 1.8 in 4.57 cm 3.6 in 9.15 cm 6.
PAGE 143
Technical Specifications A - 15 SE4600 Long Range Imager Decode Zones Figure A-6 and Figure A-7 show the decode zones for the SE4600 scan engine. The figures are typical values. Table A-8 lists the typical distances for selected bar code densities. The minimum element width (or “symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol. Note: Typical performance at 73.4°F (23°C) on high quality symbols. 12.0 10 mil Data Matrix 24.0 5 mil Code 39 10.0 26.0 7.
PAGE 144
A - 16 MC9190-G Integrator Guide Note: Typical performance at 73.4°F (23°C) on high quality symbols. 20 mil Code 39 8 cm 36 91.4 24 61.0 12 30.5 0 0 12 30.5 24 61.0 36 91.4 100 55 mil Data Matrix 130 13 40 mil Code 39 170 100 mil Data Matrix 20 210 55 mil Code 39 * 230 70 mil Reflective Code 39 288 100 mil Code 39, 100 mil Code 39 Reflective 360.0 in. 0 cm 0 in. 75 190.5 150 381.0 225 571.5 300 762.
PAGE 145
Technical Specifications A - 17 Table A-8 SE4600 Decode Distances Symbology Typical Working Range @ 25 Ft-cd Minimum Bar Code Content/ Contrast Near Far 5 mil Code 39 ABCDEFGH MRD=80% 10 in. 25.4 cm 26 in. 66.0 cm 7.5 mil Code 39 ABCDEF MRD=80% 8.5 in. 21.6 cm 38 in. 96.5 cm 10 mil Code 39 (Note 2) ABCDE MRD=80% 6.5 in. 165.1 cm 44 in. 111.8 cm 15 mil Code 128 1234 MRD=80% 7 in. 17.8 cm 49 in. 124.5 20 mil Code 39 123 MRD=80% 8 in. 20.3 cm 100 in. 254.
PAGE 146
A - 18 MC9190-G Integrator Guide Table A-8 SE4600 Decode Distances (Continued) Typical Working Range @ 25 Ft-cd Minimum Bar Code Content/ Contrast Symbology Near Far Data Matrix 10 mil 01234567890123450000 MRD=80% 12 in. 30.5 cm 24 in. 61.0 cm Data Matrix 55 mil 123456789 MRD=80% 13 in. 33.0 cm 130 in. 330.2 cm Data Matrix 100 mil 123456789 MRD=80% 20 in. 50.8 cm 210 in. 533.4 cm Notes: 1. At 23o C. 2. 6.
PAGE 147
Technical Specifications A - 19 Table A-9 Pin-Outs (Continued) PIN Number Signal Name Function 8 GND Ground, 2.5A max. 9 RI RS232C 10 CRADLE_DET Grounded by cradle when in cradle 11 DTR RS232C 12 Not connected Not connected 13 POWER_IN 12V, 2.5A max 14 CTS RS232C 15 USB_5V_DET USB 16 USB_D_MINUS USB 17 EXT_PWR_OUT 3.
PAGE 148
A - 20 MC9190-G Integrator Guide Accessory Specifications Single Slot Serial/USB Cradle Table A-10 Single SLot Serial/USB Cradle Technical Specifications Feature Description Dimensions Height: 13.02 cm (5.13 in.) Width: 15.24 cm (6.0 in.) Depth: 15.24 cm (6.0 in.
PAGE 149
Technical Specifications A - 21 Table A-11 Four Slot Ethernet Cradle Technical Specifications (Continued) Feature Description Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Charge Only Cradle Table A-12 Four Slot Charge Only Cradle Technical Specifications Feature Description Dimensions Height: 10.16 cm (4.0 in.) Width: 48.77 cm (19.00 in.) Depth:15.24 cm (6.0 in.
PAGE 150
A - 22 MC9190-G Integrator Guide Table A-13 Four Slot Battery Charger Technical Specifications (Continued) Feature Description Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.
PAGE 151
Technical Specifications A - 23 Table A-15 CAM and MSR Serial Connector Pin-outs Pin Signal 1 USB_5V_DET 2 USB_D_MINUS 3 USB_D_PLUS 4 GND 5 GND 6 PWR_EXT_OUT 7 CRADLE_DET* 8 DSR 9 DCD 10 TXD 11 CTS 12 DTR 13 RI 14 RTS 15 RXD
PAGE 152
A - 24 MC9190-G Integrator Guide
PAGE 153
Appendix B Using iDockIt Introduction iDockIt™ manages activities that can occur when the MC9190-G is connected to a host computer using a cradle (Ethernet, modem, serial or USB) or a USB or a serial cable. iDockIt can enable the MC9190-G to connect automatically to a host computer, network, or the Internet and then exchange information or launch an application. Use iDockIt to configure settings for each type of connection.
PAGE 154
B-2 MC9190-G Integrator Guide General Recommendations The MC9190-G should not be placed in a cradle or connected when the host computer to which it is physically connected is started or restarted. If the MC9190-G is cradled when the host computer is started or restarted, the MC9190-G attempts to connect before ActiveSync has fully loaded and a proper connection is impossible. Follow these general guidelines for avoiding connection problems: • Connect only one MC9190-G to the host computer at a time.
PAGE 155
Using iDockIt 6. B-3 Check Establish network connection and optionally Launch application. When the MC9190-G is placed in a cradle, iDockIt displays the settings tab corresponding to that cradle. Choose the type of connection and tap . Alternately, establish a new connection settings before placing the MC9190-G in the cradle. Launch Application Upon Connection To launch an application when connected: 1. Check Enable iDockIt. 2.
PAGE 156
B-4 MC9190-G Integrator Guide Windows Mobile 6.5 Configuration General Tab Settings on the General tab complement the options set for the cradle. Figure B-1 General Settings Tab • Enable iDockIt - Enables iDockIt to control cradle events. When the MC9190-G is placed in a cradle, iDockIt identifies the type of cradle and perform the activities configured. • Autostart - Enables iDockIt to start automatically when the MC9190-G is rebooted.
PAGE 157
Using iDockIt B-5 Auto-dismiss dialogs - Configure iDockIt to dismiss several error messages that might be displayed as iDockIt makes the connection. These messages do not require any action. To auto-dismiss a message, tap the checkbox next to its title. If the message occurs during a connection attempt, iDockIt allows it and the event appears in the Status window. • • Cannot Connect - The answering modem has disconnected. To check your connection settings and change them if needed, tap Settings.
PAGE 158
B-6 MC9190-G Integrator Guide 1. Tap Select to open the Select Auto-Launch Application window. 2. Select a File Type in the drop-down list. 3. Select a folder (as needed). 4. Select a file name in the list. 5. In the Program arguments field, enter command line parameters. 6. Tap OK. The selected application appears in the text box. • Redirect wireless LAN - When checked, iDockIt ensures that any existing wireless connection is redirected so that it does not conflict with iDockIt settings.
PAGE 159
Using iDockIt • B-7 Establish network connection to - Establishes a connection to a network when the MC9190-G is placed in a serial or USB cradle or connected to a serial or USB cable. In order to establish a connection to the network, connect the MC9190-G to a host computer with a RAS server. Selecting this option, automatically deselects Launch ActiveSync. Select this option in conjunction with Launch application. After iDockIt establishes the network connection, it launches the specified application.
PAGE 160
B-8 MC9190-G Integrator Guide When this option is checked, iDockIt continuously checks for the presence of a modem. In order for this option take effect, check RS232 checked under Ports to monitor on the General settings tab. • Launch ActiveSync - Launches ActiveSync when the MC9190-G is placed in a modem cradle. NOTE Selecting this option automatically deselects Establish network connection to and Launch application.
PAGE 161
Using iDockIt B-9 3. Enter a name for the connection. 4. In the Modem drop-down list, select the modem type. For the modem cradle, select Hayes Compatible on COM1. 5. Tap Configure and change any Port Settings in the Device Properties window, depending on requirements for the modem. 6. Tap OK. 7. Tap Next. 8. Enter the country code, area code and phone number and then tap Next. 9. Enter login information (user name, password, and domain name) and then tap Next. 10.
PAGE 162
B - 10 MC9190-G Integrator Guide Figure B-5 Status Tab • Dock Status - Indicates Docked and the type of connection (Serial, Ethernet or USB) when the MC9190-G is cradled or Not docked when the MC9190-G is removed from the cradle. • Connection - Displays the name of the connection. • IP Addresses - Displays all valid IP addresses assigned to the MC9190-G. When the MC9190-G is not cradled, displays either the IP address of the network adapter or, if no network connection, a default IP address.
PAGE 163
Using iDockIt B - 11 Windows CE 6.0 Configuration General Tab Settings on the General tab complement the options set for the cradle. Figure B-6 General Settings Tab • Enable iDockIt - Enables iDockIt to control cradle events. When the MC9190-G is placed in a cradle, iDockIt identifies the type of cradle and perform the activities configured. Uncheck this option to restore control of cradle events to Microsoft ActiveSync.
PAGE 164
B - 12 MC9190-G Integrator Guide the checkbox next to its title. If the message occurs during a connection attempt, iDockIt allows it and the event appears in the Status window. • Port Disconnected - Cannot start communications with the desktop computer. The connection was terminated. This message displays when the MC9190-G is removed from a cradle, breaking the connection. Since this is not really an error, the message can be dismissed automatically.
PAGE 165
Using iDockIt B - 13 • Disconnect after sync - Sets the MC9190-G to automatically disconnect from the selected host computer when ActiveSync completes synchronization. • Establish network connection - Establishes a connection to the network when the MC9190-G is placed in a cradle. Selecting this option, automatically deselects Launch ActiveSync. Select this option in conjunction with Launch application. After iDockIt establishes the network connection, it launches the specified application.
PAGE 166
B - 14 MC9190-G Integrator Guide • Launch ActiveSync - Launches ActiveSync when the MC9190-G is placed in a serial or USB cradle or when connected it to a serial or USB cable. NOTE Selecting this option automatically deselects Establish network connection to and Launch application. Similarly, selecting Establish network connection to or Launch application automatically deselects Launch ActiveSync.
PAGE 167
Using iDockIt B - 15 If the host computer or ActiveSync is reset, the port selection may revert to COM1. Open Connection Settings and re-select the correct USB COM port. Modem Tab If using a modem cradle, you can automatically connect to a remote host computer or network or you can choose a host computer with which you have set up a partnership using ActiveSync. Alternatively, you can connect to your network and/or launch a specified application on the MC9190-G.
PAGE 168
B - 16 MC9190-G Integrator Guide 5. Select a file name in the list. 6. Tap OK at the top of the screen. The selected application appears in the text box. • Connect using - Lists all modem connections that have been defined. If you check the General settings options to Display settings when cradled and Auto-connect after x seconds, you have an opportunity to select the appropriate modem connection when you place the MC9190-G in the cradle.
PAGE 169
Using iDockIt B - 17 Delete An Existing Modem Connection 1. In the Connect using list, select the modem connection you want to delete. 2. Tap Delete. 3. The Modem Settings dialog asks you to confirm that you want to delete the named modem connection. Tap Yes. The modem connection is removed from the drop-down list. Status Tab The Status tab displays connection-related events as they occur.
PAGE 170
B - 18 MC9190-G Integrator Guide Un-installing iDockIt On Windows Mobile 6.5 devices: 1. Exit iDockIt. 2. In the System tab, tap the Remove Programs icon. 3. Select InVision iDockIt in the program list. 4. Tap Remove and select Yes in the Remove Program dialog. 5. Tap OK. On Windows CE 6.0 devices: 1. Exit iDockIt. 2. Tap Start > Settings and double-tap the Remove Programs icon. 3. Select InVision iDockIt in the program list. 4. Tap Remove and select Yes in the Remove Program dialog. 5.
PAGE 171
Appendix C Special Software Configurations Bluetooth Configuration Setting The MC9190-G supports both the Microsoft Bluetooth stack and the StoneStreet One Bluetooth stack. Only one Bluetooth stack can be used at a time. By default, the Microsoft Bluetooth stack is enabled. A registry key on the MC9190-G can be modified to disable the Microsoft stack and enable the StoneStreet One stack.
PAGE 172
C-2 MC9190-G Integrator Guide Sample Applications and StartUpCtl Configuration The MC9190-G with Windows CE 6.0 contains a set of sample applications that can be installed on the MC9190-G. As part of the installation, an application called StartUpCtl is also installed. On the desktop, double-tap the Install Samples icon. The Sample Applications and StartUpCtl application installs on the MC9190-G and the Sample Applications window appears.
PAGE 173
Technical Specifications C-3 Switching Between QVGA and VGA Resolution in Windows CE Devices All MC9190-G configurations ship with VGA displays (640 H x 480 W resolution). All Windows CE configurations, by default, are set to QVGA resolution (320 H x 240 W). Windows CE 6.0 operating system icons and applications are designed for QVGA resolution. The user can change the display resolution from QVGA to VGA but the icons and applications appear 1/4 of the size as in QVGA mode.
PAGE 174
C-4 MC9190-G Integrator Guide Battery Usage Threshold Setting By default the Battery Usage Threshold value is set to a pre-defined value (500 by default). To change the threshold value, a registry key must be created to allow changing this value. A battery becomes unhealthy when the Battery Usage Indicator reaches a predefined threshold (end of usable life).
PAGE 175
Technical Specifications C-5 Figure C-4 BatteryMgmt Tab with Threshold Change Checkbox 2. In the Battery Usage Threshold text box, enter a new value. 3. Select the Check to change the Battery Age Threshold to read only field checkbox. 4. Tap Apply. Tap ok. The new value is set and then the registry key is deleted. WLAN Default Settings By default, the WLAN radio is off when the MC9190-G turns on.
PAGE 176
C-6 MC9190-G Integrator Guide
PAGE 177
Glossary Numeric 802.11. A group of wireless specifications developed by the Institute of Electrical and Electronics Engineers (IEEE). It specifies an over-the-air interface between a wireless client and a base station or between two wireless clients. 802.11a. Operates in the 5 GHz frequency range (5.125 to 5.85 GHz) with a maximum 54Mbit/sec. signaling rate. The 5 GHz frequency band is not as crowded as the 2.4 GHz frequency because it offers significantly more radio channels than the 802.
PAGE 178
Glossary - 2 MC9190-G Integrator Guide Association. The process of determining the viability of the wireless connection and establishing a wireless network's root and designated access points. A mobile computer associates with its wireless network as soon as it is powered on or moves into range. B Bar Code. A pattern of variable-width bars and spaces which represents numeric or alphanumeric data in machine-readable form.
PAGE 179
Glossary - 3 D DCP. See Device Configuration Package. Decode. To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar code scanned. Device Configuration Package. The Motorola Device Configuration Package provides flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts. With this package hex images that represent flash partitions can be created and downloaded to the mobile computer. E EAP.
PAGE 180
Glossary - 4 MC9190-G Integrator Guide I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification. Conformity is ensured through a software restriction of 120 seconds of laser operation within any 1000 second window and an automatic laser shutdown if the scanner's oscillating mirror fails. IEEE Address.
PAGE 181
Glossary - 5 Liquid Crystal Display (LCD). A display that uses liquid crystal sealed between two glass plates. The crystals are excited by precise electrical charges, causing them to reflect light outside according to their bias. They use little electricity and react relatively quickly. They require external light to reflect their information to the user. M Mobile Computer. In this text, mobile computer refers to the Motorola Series 9190 wireless portable computer.
PAGE 182
Glossary - 6 MC9190-G Integrator Guide Router. A device that connects networks and supports the required protocols for packet filtering. Routers are typically used to extend the range of cabling and to organize the topology of a network into subnets. See Subnet. RS-232. An Electronic Industries Association (EIA) standard that defines the connector, connector pins, and signals used to transfer data serially from one device to another. S Scanner.
PAGE 183
Glossary - 7 TKIP. (Temporal Key Integrity Protocol) A wireless encryption protocol that periodically changes the encryption key, making it harder to decode. TLS. (Transport Layer Security) TLS is a protocol that ensures privacy between communicating applications and their users on the Internet. When a server and client communicate, TLS ensures that no third party may eavesdrop or tamper with any message. TLS is the successor to the Secure Sockets Layer (SSL). V Visible Laser Diode (VLD).
PAGE 184
Glossary - 8 MC9190-G Integrator Guide
PAGE 185
Index A AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 accessories cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 CAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3, 2-24 installation . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25 USB connection . . . . . . . . . . . . . . . . .2-21, 2-25 four slot charge only cradle . . . . . . . . . . . . .2-1, 2-17 four slot Ethernet cradle . . . . . . . . . . . . . . . . . .
PAGE 186
Index - 2 MC9190-G Integrator Guide MobileDoxEthernet communication installing MobileDox . . . . . . . . . . . . . . . . . . 2-12 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii conventions notational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv copyfile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 cpf file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 CPU . . . . . . . . . . . . . . . . . . .
PAGE 187
Index - 3 MobileDox install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 MSR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3, 2-21 battery charging . . . . . . . . . . . . . . . . . . . .2-23, 2-28 installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 magnetic stripe reading . . . . . . . . . . . . . . . . . . . 2-23 power connection . . . . . . . . . . . . . . 2-22, 2-25, 2-28 serial connection . . . . . . . . . .
PAGE 188
Index - 4 MC9190-G Integrator Guide W warm boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Windows Mobile Device Center . . . . . . . . . . . . . . . . . 3-3 Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5, 4-4 Wireless Manager . . . . . . . . . . . . . . . . . . . . . . . .1-5, 4-4 WLAN 802.11a/b/g . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 189
PAGE 190
Motorola Solutions, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2011 Motorola Solutions, Inc. All Rights Reserved.