MC75A Enterprise Digital Assistant Integrator Guide
MC75A Enterprise Digital Assistant Integrator Guide 72E-133624-01 Rev.
ii MC75A Enterprise Digital Assistant Integrator Guide © 2010 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change -01 Rev. A Date 03/12/10 Description Initial release.
iv MC75A Enterprise Digital Assistant Integrator Guide
Table of Contents Revision History .................................................................................................................................... iii About This Guide Introduction ........................................................................................................................................... Documentation Set Configurations.......................................................................................................................................
viii MC75A Enterprise Digital Assistant Integrator Guide Chapter 2: Accessories Introduction .......................................................................................................................................... Single Slot USB/Serial Cradle ............................................................................................................. Setup ....................................................................................................................................
Table of Contents Installing ActiveSync ............................................................................................................................ Mobile Computer Setup ....................................................................................................................... Setting Up an ActiveSync Connection on the Host Computer ............................................................. Synchronization with a Windows Mobile 6 Device ......................................
x MC75A Enterprise Digital Assistant Integrator Guide Ending a Data Connection ............................................................................................................. MC75A6 Settings ................................................................................................................................. Phone ............................................................................................................................................. Sounds ....................
Table of Contents Chapter 7: Interactive Sensor Technology Configuration Introduction .......................................................................................................................................... IST Menu ....................................................................................................................................... General Tab .................................................................................................................................
xii MC75A Enterprise Digital Assistant Integrator Guide MC75A Accessory Specifications ........................................................................................................ Single Slot USB/Serial Cradle ........................................................................................................ Four Slot Ethernet Cradle .............................................................................................................. Four Slot Charge Only Cradle .................
About This Guide Introduction This Integrator Guide provides information about using the MC75A Enterprise Digital Assistant (EDA) and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation set for the MC75A provides information for specific user needs, and includes: • MC75A Quick Start Guide - describes how to get the MC75A EDA up and running.
xiv MC75A Enterprise Digital Assistant Integrator Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads MC75A0 WPAN: Bluetooth WLAN: 802.11a/b/g 3.5” VGA Color 256 MB RAM/ 1 GB Flash 1D laser scanner, 2D imager or camera Windows Mobile 6.5 Classic Numeric, QWERTY, AZERTY or QWERTZ keypads MC75A6 WLAN: 802.11a/b/g WPAN: Bluetooth WWAN: HSDPA GPS: SiRF III 3.
About This Guide The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 18552.0.7.5 indicates that the device is running AKU version 0.7.5. OEM Version To determine the OEM software version: Tap Start > Settings > System folder > System Info icon > System tab. BTExplorer Software NOTE To view the BTExplorer version information, the StoneStreet One Bluetooth stack must be enabled.
xvi MC75A Enterprise Digital Assistant Integrator Guide Fusion Software To determine the Fusion software version: Tap Start > Wireless Companion icon > Wireless Status icon > Versions. Phone Software To determine the Phone software version: Tap Start > Phone > Menu > Options > Phone Info or Version Information tab.
About This Guide xvii Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started provides information on MC75A configurations and accessories, charging the battery, and resetting. • Chapter 2, Accessories describes the accessories available for the MC75A and how to set up power connections and battery charging capabilities, where applicable.
xviii MC75A Enterprise Digital Assistant Integrator Guide Related Documents and Software The following documents provide more information about the MC75A.
Chapter 1 Getting Started Introduction This chapter provides information about the MC75A, accessories, charging the MC75A, and resetting the MC75A. Unpacking the MC75A Carefully remove all protective material from the MC75A and save the shipping container for later storage and shipping. Verify that you received the following equipment: • MC75A • Lithium-ion battery • Battery cover/strap assembly • Tethered stylus • Regulatory Guide • Quick Start Guide. Inspect the equipment.
1-2 MC75A Enterprise Digital Assistant Integrator Guide Charge the main battery before or after it is installed. Use one of the spare battery chargers to charge the battery (out of the MC75A), or one of the cradles to charge the battery installed in the MC75A. Installing the Main Battery NOTE The MC75A ships with either a 1950 mAh or a 3600 mAh battery. An optional 4800 mAh battery is available. To install the main battery. 1.
Getting Started 1-3 The MC75A powers up after inserting the battery and replacing the battery cover. Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 9-2. Charging the Main Battery and Memory Backup Battery Before using the MC75A for the first time, charge the main battery until the amber Charging/Battery Status LED remains lit (see Table 1-2 on page 1-4 for charge status indications).
1-4 MC75A Enterprise Digital Assistant Integrator Guide Radio Status LED (MC75A6/8 only) Scan/Decode Charging/Battery Status LED LED Figure 1-3 LED Indicators Table 1-2 LED Charge Indicators Charging/Battery Status LED Indication Off MC75A is not charging. MC75A is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered. Slow Blinking Amber (1 blink every 2 seconds) MC75A is charging. Solid Amber Charging complete.
Getting Started 1-5 When turning the MC75A on for the first time, the splash screen displays for about five minutes as the MC75A initializes its flash file system, then the calibration window appears. Note that these windows also appear upon cold boot. NOTE When the MC75A powers up after inserting a battery for the first time, the device boots and powers on automatically.
1-6 MC75A Enterprise Digital Assistant Integrator Guide Performing a Clean Boot CAUTION A clean boot should only be performed by an authorized system administrator. You must connect the MC75A to AC power during a clean boot. Removing AC power from the MC75A during a clean boot may render the MC75A inoperable. A clean boot resets the MC75A to the factory default settings. All data in the Application folder is retained.
Getting Started 1-7 These settings are configurable and the factory default settings are shown in Table 1-3 are subject to change/update. Table 1-3 Wake-up Default Settings Condition for Wake-up Power Button Automatic Time-out AC power is applied to the MC75A. No Yes The MC75A is inserted into a cradle. No Yes The MC75A is removed from a cradle. No Yes The MC75A is connected to a USB cable. Yes Yes Mobile computer is disconnected from a USB device.
1-8 MC75A Enterprise Digital Assistant Integrator Guide Figure 1-5 Card Installation 2. Insert the card with the card contacts facing up, until you feel a click. 3. Replace the memory card cover and tighten the screws. To remove an microSD card: 1. Remove the memory card cover by loosening the screws. Figure 1-6 Card Removal 2. Carefully press and release the card to eject it. 3. Remove the card from the card slot. 4. Replace the memory card cover and tighten the screws.
Getting Started 1-9 Battery Cover Latch Figure 1-7 Removing the Battery Cover 9. Lift the top of the battery cover and remove. 10. Press the battery release latch on the bottom of the battery to unlock, and lift the battery out of the well. 11. Insert the replacement battery, top first, into the battery compartment in the back of the MC75A. 12. Press the battery down into the battery compartment until the battery release latch snaps into place.
1 - 10 MC75A Enterprise Digital Assistant Integrator Guide
Chapter 2 Accessories Introduction This chapter provides set up information for various accessories of the MC75A. Table 2-1 lists all accessories available for the MC75A. Table 2-1 MC75A Accessories Accessory Part Number Description Cradles Single Slot USB/Serial Cradle CRD7X00-1000RR Charges the MC75A main battery and a spare battery. Synchronizes the MC75A with a host computer through either a serial or a USB connection.
2-2 MC75A Enterprise Digital Assistant Integrator Guide Table 2-1 MC75A Accessories (Continued) Accessory Part Number Description DEX Cable 25-76793-01R Connects the MC75A to a vending machine. Modem Dongle MDM9000-100R Provides modem connectivity to the MC75A. Modem Inverter Cables 25-70924-03R Connects the MC75A to the modem dongle. O’Neil Printer Cable 25-91519-01R Printer cable for O’Neil printers. Zebra Printer Cable 25-91518-01R Printer cable Zebra Road Warrior printers.
Accessories Single Slot USB/Serial Cradle This section describes how to set up and use a Single Slot USB/Serial cradle with the MC75A. For USB communication setup procedures see Chapter 3, ActiveSync. The Single Slot USB/Serial Cradle: • Provides 5.4 VDC power for operating the MC75A. • Synchronizes information between the MC75A and a host computer. See Chapter 3, ActiveSync for information on setting up a partnership between the MC75A and a host computer. • Charges the MC75A’s battery.
2-4 MC75A Enterprise Digital Assistant Integrator Guide Charging/Battery Status LED Figure 2-2 MC75A Battery Charging Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 2-3 Spare Battery Charging Battery Charging Indicators The Single Slot USB/Serial Cradle charges the MC75A’s main battery and a spare battery simultaneously. The MC75A’s Charge LED indicates the status of the battery charging in the MC75A. See Table 1-2 on page 1-4 for charging status indications.
Accessories 2-5 Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A. To accomplish this, for small periods of time, the MC75A or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The MC75A or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2 on page 1-4 and Table 2-2.
2-6 MC75A Enterprise Digital Assistant Integrator Guide Four Slot Ethernet Cradle This section describes how to set up and use a Four Slot Ethernet cradle with the MC75A. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating the MC75A. • Connects the MC75A (up to four) to an Ethernet network. • Simultaneously charges up to four MC75As. You cannot ActiveSync using the Four Slot Ethernet cradle.
Accessories Speed LED 2-7 Link LED Ethernet Port 1 Ethernet Port 2 Figure 2-5 Daisychaining Four Slot Ethernet Cradles Bandwidth Considerations when Daisychaining Each cradle added to the daisychain impacts the bandwidth provided to the inserted MC75As, particularly when the MC75As attempt to send and receive at data rates that exceed the bandwidth provided to the chain (typically 100 Mbps).
2-8 MC75A Enterprise Digital Assistant Integrator Guide Figure 2-6 Configure Network Adapters Window 2. In the My network card connects to: drop-down list, select the appropriate connection. 3. In the Tap an adapter to modify settings: list, select USB/Ethernet Series Adapter. Figure 2-7 IP Address Tab 4. In the IP address window, select the appropriate radio button: • Use server-assigned IP address or • Use specific IP address. Enter the IP address, Subnet mask, and Default gateway, as needed. 5.
Accessories 2-9 Figure 2-8 Name Servers Tab 6. Enter the appropriate DNS, Alt DNS, WINS, and Alt WINS server addresses. 7. Tap ok. 8. Tap ok to exit. Charging and Communication Insert the MC75A into a slot to begin charging. Speed LED Link LED Figure 2-9 MC75A Battery Charging LED Charging Indicators Charge LED The MC75A’s charge LED shows the status of the battery charging in the MC75A. See Table 1-2 on page 1-4 for charging status indications.
2 - 10 MC75A Enterprise Digital Assistant Integrator Guide The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours. Speed LED The cradle’s green Speed LED lights to indicate that the transfer rate is 100 Mbps. When it is not lit it indicates that the transfer rate is 10Mbps. Link LED The cradle’s yellow Link LED blinks to indicate activity, or stays lit to indicate that a link is established.
Accessories 2 - 11 Four Slot Charge Only Cradle This section describes how to set up a Four Slot Charge Only cradle with the MC75A. The Four Slot Charge only cradle: • Provides 5.4 VDC power for operating the MC75A. • Simultaneously charges up to four MC75As. NOTE You cannot ActiveSync using the Four Slot Charge Only cradle. To ActiveSync with a host computer, use the Single Slot USB/Serial cradle, USB Charging cable or Serial Charging cable.
2 - 12 MC75A Enterprise Digital Assistant Integrator Guide Wall Mount Bracket Use the optional Wall Mount Bracket to mount a four slot cradle to a wall. To attach the Wall Mount Bracket: 1. Use the Wall Mount Bracket as a template and mark the locations of the four mounting screws. NOTE Use fasteners appropriate for the type of wall and the Wall Mount Bracket mounting slots. The Wall Mount Bracket mounting slots are designed for a fastener with a #8 pan head. 2. Mount the fasteners to the wall.
Accessories 2 - 13 3. Swing the four slot cradle down onto the mounting bracket and align the mounting screws so that they fit into the screw slots. Wall Mount Bracket Screw Slots Power Supply Well Figure 2-13 Wall Mount Bracket 4. Tighten the mounting screws to secure the four slot cradle to the bracket. Figure 2-14 Mounting Screws 5. Connect power (see Figure 2-4 on page 2-6). The power supply should be located in the power supply well.
2 - 14 MC75A Enterprise Digital Assistant Integrator Guide VCD7X00 Vehicle Cradle This section describes how to set up a VCD7X00 vehicle cradle. Once installed in a vehicle, the cradle: • holds the MC75A securely in place • provides power for operating the MC75A • provides a serial port for data communication between an MC75A and an external device (e.g., a printer) • re-charges the battery in the MC75A • re-charges a 3600 mAh or 4800 mAh battery.
Accessories 2 - 15 Connector Pin-Outs Table 2-5 Power Input Cable Pin Signal 1 Chassis ground (Black Wire) 2 Chassis ground (Bare Wire) 3 V+ (Red Wire) 4 V+ (Red Wire) 1 Connector on Power Cable Table 2-6 Serial Cable Pin Signal Pin Signal 1 DCD 5 GND 2 RxD 6 DSR 3 TxD 7 RTS 4 DTR 8 CTS 5 GND 9 5V_OUT CAUTION Connector on Serial Cable ROAD SAFETY - Do not use the MC75A while driving. Park the vehicle first. Always ensure the MC75A is fully inserted into the cradle.
2 - 16 MC75A Enterprise Digital Assistant Integrator Guide 1.2” 3.05 cm 1.5” 3.81 cm Figure 2-15 Vehicle Cradle Mounting Template 3. Position the cradle on the mounting surface. 4. Fasten it using four #8 washers and four #8-32 self-locking nuts. Do not install a VCD7000 Vehicle Cradle on or near an air bag cover plate or within an aerobic zone. Also, do not install it in a location that affects vehicle safety or driveability.
Accessories 2 - 17 2. Route the power input cable from the cradle’s power port to the connection point for the vehicle’s power source. CAUTION 3. The means of routing and securing the power input cable from the cradle through to the vehicle power source is extremely important. Hazards associated with improper wiring can be severe. To avoid unintentional contact between the wire and any sharp edges, provide the cable with proper bushings and clamping where it passes through openings.
2 - 18 MC75A Enterprise Digital Assistant Integrator Guide Serial Device Connection The MC75A has a serial port on the bottom. When the MC75A is inserted into the cradle, it connects to the cradle’s serial port. The MC75A can then use the cradle’s serial port to communicate with an external device.
Accessories 2 - 19 Release Lever Figure 2-18 MC75A Battery Charging CAUTION Ensure the MC75A is fully inserted in the cradle. Lack of proper insertion may result in property damage or personal injury. Motorola, Inc. is not responsible for any loss resulting from the use of the products while driving. Removing the MC75A To remove the MC75A, hold back the release lever on the cradle and pull the MC75A up and out of the cradle.
2 - 20 MC75A Enterprise Digital Assistant Integrator Guide Battery Release Lever Figure 2-20 Inserting the Spare Battery 2. Insert the spare battery in the spare battery charging slot in the cradle with the charging contacts facing up and to the rear of the cradle. 3. Release the battery release lever. The battery release lever locks the spare battery into place. To remove a spare battery, hold back the battery release lever and lift the battery from the spare battery slot.
Accessories 2 - 21 Table 2-7 Vehicle Cradle Spare Battery LED Charging Indicators Spare Battery LED (on cradle) Indication Slow Blinking Amber Spare battery is charging. Solid Amber Spare battery is fully charged. Fast Blinking Amber Charging error. Off Not charging. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC75A.
2 - 22 MC75A Enterprise Digital Assistant Integrator Guide Four Slot Battery Charger This section describes how to use the Four Slot Battery Charger to charge up to four MC75A spare batteries. Battery Shim Installation Before charging a spare battery, snap the MC75A shim into the battery slot as shown in Figure 2-22. Figure 2-22 Spare Battery Shim Installation NOTE To purchase additional shims, contact your local account manager or Motorola, Inc. Part number: KT-76490-01R. Spare Battery Charging 1.
Accessories 2 - 23 Spare Battery Spare Battery Charging LEDs (4) Figure 2-23 Four Slot Spare Battery Charger Battery Charging Indicators An amber LED is provided for each battery charging well. See Table 2-8 for charging status indications. The 3600 mAh battery fully charges in approximately five hours and the 4800 mAh battery fully charges in approximately seven hours. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F).
2 - 24 MC75A Enterprise Digital Assistant Integrator Guide Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities. The following MC75A communication/charge cables are available: • Serial (RS232) Charge cable (9-pin D female with power input receptacle) • USB Client Charge cable (standard-A connector and a barrel receptacle for power) • Auto charge cable • DEX cable • Modem inverter cable • Charge only cable.
Accessories 2 - 25 Battery Charging The communication/charge cables can charge the MC75A battery and supply operating power. To charge the MC75A battery: 1. Connect the communication/charge cable power input connector to the Symbol approved power source. 2. Slide the bottom of the MC75A into the connector end of the communication/charge cable and gently press in until it latches into the MC75A. The MC75A amber Charge LED indicates the MC75A battery charging status.
2 - 26 MC75A Enterprise Digital Assistant Integrator Guide
Chapter 3 ActiveSync Introduction To communicate with various host devices, install Microsoft ActiveSync (version 4.5 or higher) on the host computer. Use ActiveSync to synchronize information on the mobile computer with information on the host computer. Changes made on the mobile computer or host computer appear in both places after synchronization.
3-2 MC75A Enterprise Digital Assistant Integrator Guide Mobile Computer Setup NOTE Microsoft recommends installing ActiveSync on the host computer before connecting the mobile computer. The mobile computer can be set up to communicate either with a USB connection. Chapter 2, Accessories provides the accessory setup and cable connection information for use with the mobile computer. The mobile computer communication settings must be set to match the communication settings used with ActiveSync. 1.
ActiveSync 3-3 Figure 3-2 ActiveSync Window NOTE 2. Assign each mobile computer a unique device name. Do not try to synchronize more than one mobile computer to the same name. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears. Figure 3-3 Connection Settings Window 3. Select the appropriate check box for the type of connection used. 4. Select the Show status icon in Taskbar check box. 5. Select OK to save any changes made.
3-4 MC75A Enterprise Digital Assistant Integrator Guide Figure 3-4 Synchronization Setup Wizard Window 2. Click Next. Figure 3-5 Synchronization Directly With a Server Window 3. Select the check box to synchronize with a server running Microsoft Exchange if applicable. 4. Click Next.
ActiveSync Figure 3-6 Synchronization Option Window 5. Select the appropriate settings and click Next. Figure 3-7 Wizard Complete Window 6. Click Finish.
3-6 MC75A Enterprise Digital Assistant Integrator Guide During the first synchronization, information stored on the mobile computer is copied to the host computer. When the copy is complete and all data is synchronized, the mobile computer can be disconnect from the host computer. NOTE The first ActiveSync operation must be performed with a local, direct connection. Windows Mobile retains partnerships information after a cold boot.
Chapter 4 Application Deployment for Mobile 6 Introduction This chapter describes new features in Windows Mobile 6 including new security features, how to package applications, and procedures for deploying applications onto the MC75A. Security The MC75A implement a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust.
4-2 MC75A Enterprise Digital Assistant Integrator Guide This means that only applications signed with a certificate from the Privileged Execution Trust Certificate Store can run.
Application Deployment for Mobile 6 4-3 Installing Certificates Use XML provisioning to query and delete certificates from certificate stores.
4-4 MC75A Enterprise Digital Assistant Integrator Guide may not work properly. Refer to the Windows Mobile Version 6 Help file for finding information on Remote API security policies. Packaging NOTE Applications compiled for Windows Mobile 6 are not backward-compatible with previous versions. Packaging combines an application's executable files into a single file, called a package. This makes it easier to deploy and install an application to the MC75A.
Application Deployment for Mobile 6 4-5 • Open the Storage Card directory. • Tap the package CAB file. The application installs on the MC75A. Installation Using AirBEAM The AirBEAM Smart Client provides backward-compatible legacy AirBEAM functionality and backward-compatible legacy MSP 2.x Level 2 Agent functionality. Refer to the AirBEAM Smart Windows CE Client Product Reference Guide, p/n 72-63060-01, for instructions for AirBEAM Smart client. MSP 3.
4-6 MC75A Enterprise Digital Assistant Integrator Guide 7. The Update Loader application first looks for a file on a storage card. If it does not find it, it looks in the \temp directory. When it finds the appropriate file, it loads the package onto the MC75A. A progress bar displays until the update completes. 8. The MC75A re-boots. 9. The calibration screen appears.
Application Deployment for Mobile 6 4-7 certain privileges (roles). Some registry keys require you to simply be an Authenticated User, while other registry keys require you to be a Manager. Refer to the Microsoft Windows Mobile 6 Help file, Metabase Settings for Registry Configuration Service Provider section, for the default role settings in Windows Mobile 6. For those registry settings that require the Manager role, the CPF file must be signed with a privileged certificate installed on the device.
4-8 MC75A Enterprise Digital Assistant Integrator Guide SampleReg.xml CopyFiles CopyFiles copies files from one folder to another on a clean boot. During a clean boot CopyFiles looks for files with a .CPY extension in the root of the Application FFS partition.
Application Deployment for Mobile 6 4-9 Random Access Memory Executing programs use RAM to store data. Data stored in RAM is lost upon a warm boot. RAM also included a volatile file storage area called Cache Disk. Volatile File Storage (Cache Disk) Windows Mobile 6 memory architecture uses persistent storage for all files, registry settings, and database objects to ensure data is retained even after a power failure.
4 - 10 MC75A Enterprise Digital Assistant Integrator Guide File Types SCM uses three types of files: • System Configuration Template (.SCT) files are XML files that define the configurable parameters for a device. • Registry Configuration Service Provider XML files for device provisioning. • CAB Provisioning Format (.CPF) file which is a .CAB archive that contains the provisioning XML. This file is downloaded to the MC75A and merged upon a cold boot.
Application Deployment for Mobile 6 4 - 11 Table 4-1 SCM Menu Functions (Continued) Menu Item Description Export Changes to .xml Export the changed parameter values to an XML file. Export Changes to .cpf Export the changed parameter values to an CPF file. Export all to .xml Export all the parameter values to an XML file. Export all to .cpf Export all the parameter values to an CPF file. Exit Exit System Configuration Manager. Device Menu Device type Change the current device type template.
4 - 12 MC75A Enterprise Digital Assistant Integrator Guide Figure 4-2 Sample Status Bar The sample status bar in Figure 4-2 shows that the current configuration file contains 1 Invalid Parameter and 2 Modified Parameters. File Deployment The CPF file created by the SCM export function must be deployed to the MC75A. 1. Optionally, use the Authenticode tools to sign the .cpf file. 2. Make the .cpf file read-only, then copy it to the MC75A. 3. Tap the filename to install. 4.
Chapter 5 MC75A6 - GSM Configuration Introduction This chapter explains how to verify MC75A6 service on an Global System for Mobile communications (GSM) wireless network and establish settings. GSM networks deliver mobile voice and data services, such as Short Message Service (SMS)/Text Messaging, with full roaming capabilities across the world. High-speed Downlink Packet Access (HSDPA) enabled networks offer Internet-based content and packet-based data services.
5-2 MC75A Enterprise Digital Assistant Integrator Guide SIM Cover Figure 5-1 Lifting the SIM Cover 6. Insert the SIM card, as shown in Figure 5-2, with the cut edge of the card facing out and the contacts facing down. Figure 5-2 Inserting the SIM Card 7. Lower the SIM cover and use the stylus to slide it in place. 8. Replace the battery and battery cover. 9. Press the red Power button. 10.
MC75A6 - GSM Configuration 5-3 MC75A6 Service Verification MC75A6 phone and data services require a live SIM card, obtained from a service provider, installed in the MC75A phone. The SIM card has embedded circuitry on one side of its surface which, when inserted into an MC75A phone, provides phone service. The SIM card provides a phone number, determines the features or services available to the subscriber, and identifies the subscriber to the network.
5-4 MC75A Enterprise Digital Assistant Integrator Guide b. Ensure the service provider’s network appears in the Current network: field. c. If the network does not appear, tap Find Network. If the network still does not appear, verify that the SIM card was installed correctly. If it was, and no network appears, contact the service provider. Configuring a Data Connection A data connection allows Internet access across a wireless network. To set up a new data connection: 1.
MC75A6 - GSM Configuration Figure 5-7 Connections Window - Access Point Name 7. Enter the APN from the service provider in the Access point name: text box. 8. Tap Next. Figure 5-8 Connections Window - User Name & Password 9. Enter a username in the User name text box, if required by the service provider. 10. Enter a password in the Password text box, if required by the service provider. 11. Enter a domain name in the Domain text box, if required by the service provider. 12. Tap Finish. 13.
5-6 MC75A Enterprise Digital Assistant Integrator Guide Figure 5-9 Connectivity Dialog Box 4. Tap Settings. 5. Tap Connections icon. 6. Tap Managing existing connections. 7. Tap and hold on the data connection until a menu appears. Figure 5-10 Data Connection 8. Select Connect.
MC75A6 - GSM Configuration 9. 5-7 If the SIM card is protected with a Personal Identification Number (PIN), a dialog box pops up requesting the appropriate PIN to unlock the SIM card. In this case, enter the PIN and tap OK. NOTE Place emergency calls at any time, without entering a PIN or a SIM card. 10. When a connection is established, launch Internet Explorer to browse the Internet or launch an applicable application.
5-8 MC75A Enterprise Digital Assistant Integrator Guide MC75A6 Settings Use the Phone Settings window to customize settings, such as the ring type and ring tone for incoming calls, security options, and other options depending on the type of service. Phone Use the Phone tab to customize ring type, ring tone, keypad tone, and security options. Tap Start > Settings > Personal folder > Phone icon > Phone tab or Start > Phone > Menu > Options > Phone tab.
MC75A6 - GSM Configuration 5-9 Security Enabling a PIN NOTE Place emergency calls at any time, without requiring a PIN or a SIM card. To require a PIN when using the phone: 1. From the Phone tab (Figure 5-13), select the Require PIN when phone is used check box under Security. Figure 5-14 Enter PIN 2. Use the touch keypad to enter a four to eight digit PIN. 3. Tap Enter to enable the PIN and return to the Phone tab.
5 - 10 MC75A Enterprise Digital Assistant Integrator Guide 4. Tap OK to confirm the change. 5. Tap OK to exit settings. Services Use the Services tab to configure settings for subscribed phone services.
MC75A6 - GSM Configuration 5 - 11 Caller ID Enable caller ID to reveal the identity of the person making an outgoing call. Select the Everyone radio button to always display the caller ID. Select the No one radio button to prevent the caller’s identity from appearing to others. Figure 5-17 Caller ID Call Forwarding NOTE Call Forwarding may not be available on all networks. Check with your service provider for availability. Use call forwarding to forward incoming calls to a different phone number.
5 - 12 MC75A Enterprise Digital Assistant Integrator Guide Figure 5-18 Call Forwarding Call Waiting NOTE Call Waiting may not be available on all networks. Check with your service provider for availability. Call waiting notifies you of an incoming call when the phone is in a phone session. Select the Notify me radio button to enable call waiting. Select the Do not notify me radio button to disable call waiting.
MC75A6 - GSM Configuration 5 - 13 Figure 5-20 Voice Mail and Text Messages Fixed Dialing Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed Dialing list. 1. Select Fixed Dialing and tap Get Settings. Figure 5-21 Fixed Dialing Window 2. Select the Enable fixed dialing check box. 3. To add a number to the list, tap Menu > Add. 4. Enter the phone number or area code to restrict and tap Done. 5.
5 - 14 MC75A Enterprise Digital Assistant Integrator Guide Changing Networks Manually 1. Tap Start > Settings > Personal folder > Phone icon > Network tab or Start > Phone > Menu > Options > Network tab. Figure 5-22 MC75A Phone Window - Network Tab 2. From the Network selection drop-down list, select Manual. Figure 5-23 Choose Network 3. From the Choose Network window, select the network to use. 4. Tap OK. Viewing Available Networks To view all wireless networks available: 1.
MC75A6 - GSM Configuration 5 - 15 Figure 5-24 MC75A Phone Window - Network Tab 2. Tap Find Network. Figure 5-25 Choose Network 3. From the Choose Network window, select the network to use. 4. Tap OK. Setting Preferred Networks Set networks in a preferred order of access. Setting preferred networks allows the MC75A to access a second preferred network if the first is unavailable. 1. Tap Start > Settings > Personal folder > Phone icon > Network tab or Start > Phone > Menu > Options > Network tab.
5 - 16 MC75A Enterprise Digital Assistant Integrator Guide 2. Tap Set Networks to view all available networks. Figure 5-27 Preferred Networks 3. Select the preferred networks by tapping one or more check boxes. 4. Tap Move Up and Move Down, as necessary, to place the selected networks in the preferred order. 5. Tap OK to send the new settings to the network. 6. From the Network tab, select Automatic from the Network selection drop-down list. 7. Tap OK to exit settings.
MC75A6 - GSM Configuration 5 - 17 Network Time Synchronization The MC75A can be configured to synchronize the clock with the time from the carrier network. A registry key on the MC75A has to be created to enable this feature. Using a registry editor, navigate to the following: [HKEY_LOCAL_MACHINE\SOFTWARE\Symbol\RIL\RHA\HC25] Create the following key: “SyncSystemTime”=dword:00000001 where: dword:0 = disabled dword:1 = enabled After setting the registry key, warm boot the MC75A.
5 - 18 MC75A Enterprise Digital Assistant Integrator Guide where: dword:0 = Display network provider name dword:1 - Display service provider name (default) dword:2 - Display both network provider and service provider name
Chapter 6 MC75A8 - CDMA Configuration Introduction This chapter explains how to activate an MC75A8 on a Code Division Multiple Access (CDMA) wireless network and establish settings. CDMA is a form of wireless multiplexing in which data (e.g., Short Message Service) can be sent over multiple frequencies simultaneously, optimizing the use of available bandwidth.
6-2 MC75A Enterprise Digital Assistant Integrator Guide CDMA Phone Activation CDMA phone service is available from a number of service providers including Sprint® and Verizon Wireless®. In addition to service activation for each provider, various settings may be required for the MC75A to operate as a phone. There can be different Activation Wizards depending upon the carrier. Verizon Wireless and Sprint use an automatic activation processes. All other carriers use the manual activation process.
MC75A8 - CDMA Configuration Sprint Activation Automatic Activation To activate the phone using Sprint service: 1. Ensure the MC75A8 is in a strong signal area. 2. The Activation Wizard automatically starts whenever the phone is turned on. Figure 6-2 Activation Wizard 3. Tap Provision. If communication with the network is successful, a confirmation window appears. Figure 6-3 Activation Wizard Confirmation Window 4. Tap Yes. 5. Automatic provisioning begins.
6-4 MC75A Enterprise Digital Assistant Integrator Guide Figure 6-4 Provisioning Complete If activation is unsuccessful, a window appears to re-try the activation process. Tap Yes to try again. 6. Tap OK to close the application. NOTE If activation was not successful, contact the service provider. Manual Activation To manually activate the phone: 1. Ensure the MC75A8 is in a strong signal area. 2. Tap Start > Phone > Menu > Activation Wizard... . Figure 6-5 Activation Wizard 3. Tap Next >.
MC75A8 - CDMA Configuration 6-5 Figure 6-6 Activation Wizard - Enter Activation Code 4. Enter the 6-digit activation code from your service provider. 5. Tap Next >. If the activation code is incorrect, an error dialog box appears. Figure 6-7 Activation Wizard - MDN and MSID 6. Enter the MDN and MSID. The MDN and MSID are the area code and phone number received from the service provider. 7. Tap Next >. A confirmation dialog box appears. Figure 6-8 Activation Wizard - Confirmation 8.
6-6 MC75A Enterprise Digital Assistant Integrator Guide Figure 6-9 Activation Wizard - Activation Complete 9. Tap Finish to complete activation. NOTE If activation was not successful, contact the service provider. Activation Test To test the service. 1. Tap Start > Phone. Figure 6-10 Phone Window - Example 2. Ensure the carrier name displays on the window. 3. Make a voice call to ensure activation was successful. NOTE If activation was not successful, contact the service provider.
MC75A8 - CDMA Configuration 6-7 Establishing a Data Connection NOTE Ensure that you have data service activated with your service provider. A data connection allows Internet access across a wireless network. Data connection is pre-packaged with service accounts. To verify active data service: 1. Tap Start > Internet Explorer. 2. In the address bar, enter a URL for a web site. 3. Tap to display the Connectivity dialog. The dialog box displays the data connection information.
6-8 MC75A Enterprise Digital Assistant Integrator Guide CDMA Settings Use the Phone Settings window to customize CDMA phone settings, such as the ring type and ring tone for incoming calls and other options depending on the type of service. Phone Use the Phone tab to customize ring type, ring tone and keypad tone when entering phone numbers. 1. Tap Start > Settings > Personal folder > Phone icon > Phone tab. or Start > Phone > Menu > Options > Phone tab. Figure 6-12 Phone Window - Phone Tab 2.
MC75A8 - CDMA Configuration 8. 6-9 Tap ok to exit settings. NOTE Turning off sounds saves power and prolongs battery life. Location Settings Use the Location tab to allow the network to detect the position of the MC75A’s radio. 1. Tap Start > Settings > Personal folder > Phone icon > Location Settings tab. or Start > Phone > Menu > Options > Location Settings tab. Figure 6-13 Phone Window - Location Tab (Typical) 2.
6 - 10 MC75A Enterprise Digital Assistant Integrator Guide Figure 6-14 Phone Window - Sprint Data Tab 2. Tap Repair Connectiod to reset PCS Vision connection settings. 3. Tap Yes. Figure 6-15 Reset Connection Completed Dialog 4. Tap ok. 5. Tap Provision to manually start IP-based Over-The-Air (IOTA) provisioning. IOTA is used to provision various data elements such as Wireless Application Protocol (WAP) configuration parameters and roaming lists to the MC75A over-the-air.
MC75A8 - CDMA Configuration 6 - 11 Figure 6-16 Phone Window - Verizon Data Tab 2. Tap Repair Connectoid to reset connection settings for National Access. 3. Tap Yes. 4. Tap ok. 5. Tap ok to exit settings. Additional Service provider Data Settings Use the Data tab to reset connection settings for the 3G connection. 1. Tap Start > Settings > Personal folder > Phone icon > Data Settings tab. or Start > Phone > Menu > Options > Data Settings tab. Figure 6-17 Phone Window - Data Tab 2.
6 - 12 MC75A Enterprise Digital Assistant Integrator Guide System Settings Use the System Settings tab to select roaming options. Tap Start > Settings > Personal folder > Phone icon > System Settings tab. or Tap Start > Phone > Menu > Options > System tab. Sprint System Figure 6-18 Phone Window - System Settings Tab - Sprint 1. Roaming: • Select the Automatic radio button to allow the phone to automatically seek a roaming network where the Sprint Nationwide PCS Network is not available.
MC75A8 - CDMA Configuration 6 - 13 Verizon System Figure 6-19 Phone Window - System Settings Tab - Verizon 1. System Select allows the user to change the system roaming preference of the radio in order to control the type of network the radio can lock onto for service. • Select the Automatic radio button to allow the radio to lock onto networks based on the provisioning of the radio.
6 - 14 MC75A Enterprise Digital Assistant Integrator Guide Figure 6-20 Phone Window - Version Information Tab 2. Tap ok to exit settings. Services Depending on the type of subscribed phone services, the following services may be available: call barring, caller ID, call forwarding, call waiting, voice mail and Short Message Service (SMS). Call Barring (Call Blocking) Call barring blocks certain types of incoming and/or outgoing calls.
MC75A8 - CDMA Configuration 6 - 15 To disable call forwarding: 1. Enter *73 (Verizon Wireless) on the phone keypad. 2. Tap Talk. 3. A beep sounds indicating deactivation. 4. Tap End. Call Waiting NOTE Call Waiting may not be available on all networks. Check with your service provider for availability. Call waiting notifies the user of an incoming call when the phone is in a phone session. This service is setup when an account is opened with the service provider.
6 - 16 MC75A Enterprise Digital Assistant Integrator Guide
Chapter 7 Interactive Sensor Technology Configuration Introduction This chapter provides information for configuring the Interactive Sensor Technology (IST) settings. IST settings can be accessed: • Tap Start > Settings > System > IST Settings icon. • Tap the IST Settings icon in the Command bar (if the classic Today screen is configured). IST Settings Icon Figure 7-1 IST Settings Icon IST Menu Use this menu to access the configuration settings listed in Table 7-1.
7-2 MC75A Enterprise Digital Assistant Integrator Guide General Tab Use the General tab to view IST software information and control the display of the IST Setting icon. Figure 7-2 General Tab Table 7-2 IST General Tab Information Item Description Firmware Version Displays the version information of IST device firmware. Driver Version Displays the version information of IST driver. Sensor ID Displays identification tag of the sensor. Sensor Description Displays a description of the sensor.
Interactive Sensor Technology Configuration 7-3 Figure 7-3 Power Management Tab Keep Alive On Motion Select the Enabled checkbox to prevent the MC75A from going into suspend mode while it is in motion. The motion sensitivity is configurable. To set the sensitivity, tap the Change Sensitivity… button. NOTE There is no time out defined for suspend due to IST inactivity. To aggressively manage power, while there is no motion, set the MC75A suspend time out to a very short time using system power settings.
7-4 MC75A Enterprise Digital Assistant Integrator Guide Figure 7-4 Set IST Sensitivity Window Display Tab Use the Display tab configure display interaction settings. Figure 7-5 Display Tab The Auto Orientation parameter controls the display rotation according to the MC75A orientation. Select the Auto radio button to enable this feature. Auto orientation is disabled by default. Select the Manual radio button to manually select screen orientation.
Interactive Sensor Technology Configuration 7-5 Figure 7-6 Event Log Tab The Motion Event Summery list displays a summary of the event report. To view the full report tap the Motion Event Details… button. Use the Audible Notification panel to enable playing of a wave file when the MC75A is dropped. Select a desired .wav file from the Sounds: drop-down list. Motion Event Details The Motion Event Detail list displays the date and time, duration and the type of the drop event.
7-6 MC75A Enterprise Digital Assistant Integrator Guide
Chapter 8 Wireless Applications Introduction Wireless Local Area Networks (LANs) allow mobile computers to communicate wirelessly and send captured data to a host device in real time. Before using the MC75A on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the MC75A must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware. NOTE 802.11d is enabled by default.
8-2 MC75A Enterprise Digital Assistant Integrator Guide Figure 8-1 Wireless Applications Window Signal Strength Icon The Signal Strength icon appears on the Home screen and in the task tray when using the Classic Home screen.
Wireless Applications 8-3 Table 8-1 Signal Strength Icons Descriptions Icon None Status Action Excellent signal strength Wireless LAN network is ready to use. Very good signal strength Wireless LAN network is ready to use. Good signal strength Wireless LAN network is ready to use. Fair signal strength Wireless LAN network is ready to use. Notify the network administrator that the signal strength is only “Fair”. Poor signal strength Wireless LAN network is ready to use.
8-4 MC75A Enterprise Digital Assistant Integrator Guide Turning the WLAN Radio On and Off To turn the WLAN radio off, tap the connection icon at the top of the screen and select Wireless Manager. Tap the Wi-Fi bar to turn off the radio. Figure 8-4 Disable Radio To turn the WLAN radio on, tap the connection icon at the top of the screen and select Wireless Manager. Tap the Wi-Fi bar to turn on the radio.
Chapter 9 Maintenance and Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC75A, and provides troubleshooting solutions for potential problems during MC75A operation. Maintaining the MC75A For trouble-free service, observe the following tips when using the MC75A: • Do not scratch the screen of the MC75A. When working with the MC75A, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
9-2 MC75A Enterprise Digital Assistant Integrator Guide • A screen protector is applied to the MC75A. Motorola recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. Benefits include: • Protection from scratches and gouges • Durable writing and touch surface with tactile feel • Abrasion and chemical resistance • Glare reduction • Keeping the device’s screen looking new • Quick and easy installation.
Maintenance & Troubleshooting 9-3 • Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Enterprise Mobility support. • For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
9-4 MC75A Enterprise Digital Assistant Integrator Guide • Can of compressed air with a tube. Cleaning the MC75A Housing Using the alcohol wipes, wipe the housing including keys and in-between keys. Display The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dried the display with a soft, non-abrasive cloth to prevent streaking.
Maintenance & Troubleshooting 6. 9-5 Ensure that there is no lint left by the cotton tipped applicator, remove lint if found. CAUTION Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 7. If grease and other dirt can be found on other areas of the cradle, use lint free cloth and isopropyl alcohol to remove. 8. Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
9-6 MC75A Enterprise Digital Assistant Integrator Guide Troubleshooting MC75A Table 9-1 Troubleshooting the MC75A Problem MC75A does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the MC75A. Lithium-ion battery not installed properly. Ensure battery is installed properly. See Installing the Main Battery on page 1-2. System crash. Perform a warm boot. If the MC75A still does not turn on, perform a cold boot.
Maintenance & Troubleshooting 9-7 Table 9-1 Troubleshooting the MC75A (Continued) Problem MC75A shuts off. Cause MC75A is inactive. The MC75A turns off after a period of inactivity. If the MC75A is running on battery power, set this period from 1 to 5 minutes, in one-minute intervals. If the MC75A is running on external power, set this period to 1, 2, 5, 10, 15, or 30 minutes. Check the Power window by selecting Start > Settings > System tab and tapping the Power icon.
9-8 MC75A Enterprise Digital Assistant Integrator Guide Table 9-1 Troubleshooting the MC75A (Continued) Problem Cause The MC75A does not accept scan input. Scanning application is not loaded. Load a scanning application on the MC75A. See the system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the MC75A within proper scanning range. MC75A is not programmed for the bar code.
Maintenance & Troubleshooting Single Slot USB/Serial Cradle Table 9-3 Troubleshooting the Single Slot USB/Serial Cradle Symptom LEDs do not light when MC75A or spare battery is inserted. MC75A battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power.
9 - 10 MC75A Enterprise Digital Assistant Integrator Guide Four Slot Ethernet Cradle Table 9-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Battery is not charging. During communication, no data was transmitted, or transmitted data was incomplete. Cause Solution MC75A removed from the cradle too soon. Replace the MC75A in the cradle. The 3600 mAh capacity battery fully charges in less than five hours. Tap Start > Settings > System > Power to view battery status. Battery is faulty.
Maintenance & Troubleshooting 9 - 11 Table 9-5 Troubleshooting the Vehicle Cradle Symptom Possible Cause No data transmitted, or transmitted data was incomplete. Action MC75A removed from cradle during communication. Replace MC75A in cradle and retransmit. No null modem cable was used. Some external devices require a null modem cable. Retransmit using a null modem cable. Incorrect cable configuration. See the system administrator. Cable missing or disconnected. Re-connect cable.
9 - 12 MC75A Enterprise Digital Assistant Integrator Guide Table 9-7 Troubleshooting the Cables (Continued) Symptom During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action Cable was disconnected from MC75A during communications. Re-attach the cable and retransmit. Incorrect cable configuration. See the system administrator. Communication software is not installed or configured properly. Perform setup as described in the Chapter 3, ActiveSync.
Appendix A Technical Specifications Technical Specifications The following tables summarizes the intended operating environment and technical hardware specifications for the MC75A and accessories. MC75A Table A-1 MC75A Technical Specifications Item Description Physical Characteristics Dimensions MC75A0: Length: 15.2 cm (6.00 in.) Width: 8.4 cm (3.30 in.) Depth: 4.4 cm (1.70 in.) MC75A6/8: Length: 17.78 cm (7.0 in.) Width: 8.4 cm (3.30 in.) Depth: 4.4 cm (1.70 in.) Weight MC75A0: 364 g (12.
A-2 MC75A Enterprise Digital Assistant Integrator Guide Table A-1 MC75A Technical Specifications (Continued) Item Description Touch Panel Glass analog resistive touch Backlight LED backlight Main Battery Rechargeable Lithium Ion 3.7V, 1950, 3600 or 4800 mAh Smart Battery Backup Battery NiMH battery (rechargeable) 15 mAh 2.4V (not user-accessible) Expansion Slot User accessible microSD slot with SDHC support (with secure cover).
Technical Specifications A-3 Table A-1 MC75A Technical Specifications (Continued) Item Description Wireless WAN Data and Voice Communications Wireless Wide Area Network (WWAN) radios MC75A6: GSM: HSDPA (850, 900, 1800, 1900 and 2100 MHz) MC75A8: CDMA: EVDO Rev A (800 and 1900 MHz) GPS Integrated, Autonomous and Assisted-GPS (A-GPS) through SUPL; SiRFstarIII GSC3f/LP choppiest. Wireless LAN Data and Voice Communications Wireless Local Area Network (WLAN) radio Tri-mode IEEE® 802.
A-4 MC75A Enterprise Digital Assistant Integrator Guide Table A-1 MC75A Technical Specifications (Continued) Item Description Shock 2,000 +/- 5% G Scan Rate 50 (+/- 6) scans/sec (bidirectional) Scan Angle 46.5° (typical) Laser Power 1.0 mW nominal 2D Imager Engine (SE4500) Specifications Field of View Horizontal - 40° Vertical - 25° Optical Resolution 752X 480 V pixels (gray scale) Roll 360° Pitch Angle +/- 60° from normal Skew Tolerance +/- 60° from normal Ambient Light 9,000 ft.
Technical Specifications Table A-2 MC75A COM Port Definitions COM Port Definition COM5 BTVCOM COM6 USBVCOM BTS6 Bluetooth (Radio I/O) COM7 Available COM8 GPSId (GPSMux) COM9 BTVCOM MC75A Pin-Outs Pin 1 Figure A-1 External Connector Table A-3 External Connector Pin-Outs Pin Description 1 Power Gnd 2 CRADLE_DETECT 3 RS232_DCD/TRIGGER 4 USB_D- 5 USB_D+ 6 USB_Gnd 7 USB_Vbus 8 USB_ID 9 RS232_TXD 10 RS232_RXD 11 RS232_RTS 12 RS232_CTS 13 RS232_DTR A-5
A-6 MC75A Enterprise Digital Assistant Integrator Guide Table A-3 External Connector Pin-Outs (Continued) Pin Description 14 RS232_DSR 15 External_5.0V_Out 16 External DC In_5.4V MC75A Accessory Specifications Single Slot USB/Serial Cradle Table A-4 Single Slot USB/Serial Cradle Technical Specifications Feature Description Dimensions Length: 14.54 cm (5.72 in.) Width: 11.05 cm (4.35 in.) Height: 9.10 cm (3.58 in.) Weight 196 g (6.
Technical Specifications Four Slot Ethernet Cradle Table A-5 Four Slot Ethernet Cradle Technical Specifications Feature Description Dimensions Length: 46.78 cm (18.42 in.) Width: 11.00 cm (4.33 in.) Height: 13.70 cm (5.39 in.) Weight 1079 g (2.
A-8 MC75A Enterprise Digital Assistant Integrator Guide Table A-6 Four Slot Charge Only Cradle Technical Specifications (Continued) Feature Description Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Battery Charger Table A-7 Four Slot Battery Charger Technical Specifications Feature Description Dimensions Length: 21.00 cm (8.27 in.) Width: 15.50 cm (6.10 in.
Technical Specifications Table A-8 Magnetic Stripe Reader (MSR) Technical Specifications (Continued) Feature Description Swipe Speed 5 to 50 in. (127 to 1270 mm) /sec, bi-directional Decoders Generic, Raw Data Mode Buffered, unbuffered Track Reading Capabilities Tracks 1 and 3: 210 bpi Track 2: 75 and 210 bpi, autodetect Operating Temperature 0°C to 50°C (32°F to 122°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Humidity 5% to 95% non-condensing Drop 1.22 m (4 ft.
A - 10 MC75A Enterprise Digital Assistant Integrator Guide
Glossary A ActiveSync. ActiveSync is a data synchronization program developed by Microsoft for use with Windows Mobile operating systems. AFH. Adaptive Frequency Hopping AKU. (Adaptation Kit Update) Updates to the Windows Mobile operating system. API. (Application Programming Interface) An interface by means of which one software component communicates with or controls another.
Glossary - 2 MC75A Enterprise Digital Assistant Integrator Guide boot or boot-up. The process a computer goes through when it starts. During boot-up, the computer can run self-diagnostic tests and configure hardware and software. bps. See Bits Per Second. Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit.
Glossary - 3 Decode. To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar code scanned. Decode Algorithm. A decoding scheme that converts pulse widths into data representation of the letters or numbers encoded within a bar code symbol. Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol with a certain minimum element width. Device Configuration Package.
Glossary - 4 MC75A Enterprise Digital Assistant Integrator Guide I IDE. Intelligent drive electronics. Refers to the solid-state hard drive type. IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification.
Glossary - 5 L LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. laser scanner. A type of bar code reader that uses a beam of laser light. LCD. See Liquid Crystal Display. LED Indicator. A semiconductor diode (LED - Light Emitting Diode) used as an indicator, often in digital displays.
Glossary - 6 MC75A Enterprise Digital Assistant Integrator Guide O Open System Authentication. Open System authentication is a null authentication algorithm. P PAN. Personal area network. Using Bluetooth wireless technology, PANs enable devices to communicate wirelessly. Generally, a wireless PAN consists of a dynamic group of less than 255 devices that communicate within about a 33-foot range. Only devices within this limited area typically participate in the network. PING.
Glossary - 7 SDK. Software Development Kit Shared Key. Shared Key authentication is an algorithm where both the AP and the MU share an authentication key. Soft Reset. See Warm Boot. Space. The lighter element of a bar code formed by the background between bars. Specular Reflection. The mirror-like direct reflection of light from a surface, which can cause difficulty decoding a bar code. Start/Stop Character.
Glossary - 8 MC75A Enterprise Digital Assistant Integrator Guide Terminal Emulation. A “terminal emulation” emulates a character-based mainframe session on a remote non-mainframe terminal, including all display features, commands and function keys. The VC5000 Series supports Terminal Emulations in 3270, 5250 and VT220. TFTP. (Trivial File Transfer Protocol) A version of the TCP/IP FTP (File Transfer Protocol) protocol that has no directory or password capability.
Index A accessories auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 2-1 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2, 2-24 communication/charge cables . . . . . . . . . . . . . 2-24 battery charging . . . . . . . . . . . . . . . . . . . . . 2-25 LED indicators . . . . . . . . . . . . . . . . . . . . . . 2-25 DEX cable . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1, 2-2 EMDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 MC75A Enterprise Digital Assistant Integrator Guide cold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 warm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii C CAB files . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4, 4-7, 4-10 deployment via ActiveSync . . . . . . . . . . . . . . . . . 4-4 deployment via AirBEAM . . . . . . . . . . . . . . . . . .
Index - 3 E EDA configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 EMDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii, 4-12 enabling PIN for phone use . . . . . . . . . . . . . . . . . . . . 5-9 enhanced operator name string . . . . . . . . . . . . . . . . 5-17 Enterprise Mobility Developer Kit . . . . . . . . . . xviii, 4-12 enterprise mobility developer kit . . . . . . . . . . . . . . . . 2-2 EONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 4 MC75A Enterprise Digital Assistant Integrator Guide O O’Neil printer cable . . . . . . . . . . . . . . . . . . . . . . . . . 2-24 operating environment . . . . . . . . . . . . . . . . . . . . . . . . A-1 operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xiv P packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 persistent storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 phone activation . . . . . . . . . . . . . . . . . . . . .
Index - 5 deploying CAB files . . . . . . . . . . . . . . . . . . . . . . . 4-4 strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1, 2-2 Symbol configuration manager file deployment . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 file types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 6 MC75A Enterprise Digital Assistant Integrator Guide
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc.
