MC70 Enterprise Digital Assistant Integrator Guide
MC70 Integrator Guide 72E-71768-02 Revision A March 2007
ii MC70 Integrator Guide © 2007 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description A 1/2006 Initial release. B 8/2006 Add Revision History page. Chapter 1: Update cold boot procedure. Add clean boot procedure. Chapter 2: Update Ethernet connection procedure. Appendix A: Correct connector pin 1 location.
iv MC70 Integrator Guide
Table of Contents Patents........................................................................................................................... ii Revision History ............................................................................................................. iii About This Guide Introduction .................................................................................................................... xiii Documentation Set .........................................................
viii MC70 Integrator Guide Chapter 2: Accessories Introduction ................................................................................................................... Cables ..................................................................................................................... Cradles .................................................................................................................... Miscellaneous ...................................................................
Table of Contents Chapter 3: ActiveSync Introduction ................................................................................................................... 3-1 Installing ActiveSync ..................................................................................................... 3-1 Mobile Computer Setup ................................................................................................ 3-2 Setting Up an ActiveSync Connection on the Host Computer ..............................
x MC70 Integrator Guide Configuring a GPRS Data Connection .................................................................... Establishing a Data Connection .............................................................................. Ending a GPRS Data Connection ........................................................................... GPRS Settings .............................................................................................................. Phone ...................................
Table of Contents Battery Usage ......................................................................................................... 7-19 Manage Profiles Application ................................................................................... 7-20 Wireless Status Application .......................................................................................... 7-24 Signal Strength Window ..........................................................................................
xii MC70 Integrator Guide Appendix B: Software Configuration Radio Power Status LED ..............................................................................................
About This Guide About This Guide Introduction This Integrator Guide provides information about setting up and configuring MC70 EDAs and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. Documentation Set The documentation for the MC70 is divided into guides that provide information for specific user needs. • Microsoft® Applications User Guide for Symbol Devices - describes how to use Microsoft-developed applications.
xiv MC70 Integrator Guide Configurations This guide covers the following configurations: Configuration Radios Display Memory Data Capture Operating System Keypads MC7004 WLAN: 802.11b/g WPAN: Bluetooth WWAN:GPRS 3.5” QVGA Color 64 MB RAM/ 128 MB Flash 1D laser scanner or 2D imager Windows Mobile 5.0 Professional Numeric or QWERTY Keypad MC7090 WLAN: 802.11b/g WPAN: Bluetooth 3.5” QVGA Color 64 MB RAM/ 128 MB Flash 1D laser scanner or 2D imager Windows Mobile 5.
About This Guide xv The second line lists the operating system version and the build number. The last part of the build number represents the AKU number. For example, Build 14929.2.2.1 indicates that the device is running AKU version 2.2.1. OEM Version To determine the OEM software version: Tap Start > Settings > System tab > System Information icon > System tab. BTExplorer Software To determine the BTExplorer software version: Tap BTExplorer icon > Show BTExplorer> File > About.
xvi MC70 Integrator Guide Fusion Software To determine the Fusion software version: Tap Wireless Strength icon > Wireless Status > Versions. Phone Software To determine the Phone software version: Tap Start > Phone > Menu > Options > Version Information tab.
About This Guide xvii Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started provides information on EDA configurations and accessories, charging the battery, and resetting. • Chapter 2, Accessories describes the accessories available for the EDA and how to set up power connections and battery charging capabilities, where applicable.
xviii MC70 Integrator Guide • Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists. Related Documents and Software The following documents provide more information about the MC70 EDAs. • MC70 Quick Start Guide, p/n 72-71770-xx • MC70 Microsoft Mobile 5.0 Regulatory Information, p/n 72-71767-xx • MC70 User Guide, p/n 72E-71769-xx • Microsoft® Applications for Mobile and CE 5.
Chapter 1 Getting Started Chapter 1 Chapter 1 Getting Started Introduction This chapter provides information about the EDA, accessories, charging the EDA, and resetting the EDA. Unpacking the EDA Carefully remove all protective material from the EDA and save the shipping container for later storage and shipping.
1-2 MC70 Integrator Guide Accessories Table 1-1 lists the accessories available for the EDA. Table 1-1 MC70 Accessories Accessory Snap-on Cables Description The EDA supports the following cables: • AC line cord (country-specific) and power supply, charges the EDA. • Auto charge cable, charges the EDA using a vehicle’s cigarette lighter. • DEX cable, connects the EDA to a vending machine. • Serial cable, adds serial communication capabilities. • USB cable, adds USB communication capabilities.
Getting Started 1-3 Getting Started To start using the EDA for the first time: • Install the main battery and cover assembly. • Charge the EDA. • Power on the EDA. • Configure the EDA. Charge the main battery before or after it is installed. Use one of the spare battery chargers to charge the battery (out of the EDA), or one of the cradles to charge the battery installed in the EDA. Installing and Removing the Main Battery Installing the Main Battery Before using the EDA, install a lithium-ion battery.
1-4 MC70 Integrator Guide Battery Cover Latch Battery Cover Figure 1-2 Inserting the Battery Cover 4. Close the battery cover latches on either side of the battery cover. 5. Insert the handstrap through the handstrap slot, then tighten and press down to secure. Handstrap Handstrap Slot Figure 1-3 Inserting the Handstrap The EDA powers up after inserting the battery. Removing the Main Battery 1. Press the red Power button to suspend the EDA. 2. Loosen the handstrap at the top of the EDA. 3.
Getting Started 4. 1-5 Lift the top of the battery cover and remove. Figure 1-5 Removing the Battery Cover 5. Press the battery release latch on the bottom of the battery to unlock, and lift the battery out of the well.
1-6 MC70 Integrator Guide The standard capacity battery (1900 mAh) fully charges in less than four hours. The extended capacity battery (3800 mAh) fully charges in less than eight hours. Table 1-2 LED Charge Indicators Charging Status LED Indication Off EDA is not charging; EDA is not inserted correctly in the cradle or connected to a power source; charger is not powered. Slow Blinking Amber (1 blink every 2 seconds) EDA is charging. Solid Amber Charging complete.
Getting Started 1-7 Powering On the EDA Press the Power button to turn on the EDA. If the EDA does not power on, reset it. See Resetting the EDA on page 1-7. When turning the EDA on for the first time, the Symbol splash screen displays for about a minute as the EDA initializes its flash file system, then the calibration window appears. Note that these windows also appear upon cold boot. NOTE When the EDA powers up after inserting a battery for the first time, the device boots and powers on automatically.
1-8 MC70 Integrator Guide A clean boot resets the EDA to the factory default settings. All data is the Application folder is retained. You must download the Clean Boot Package file from the Support Central and install on the EDA. To perform a clean boot: 1. Download the Clean Boot Package from the Support Central. Follow the instructions included in the package for installing the package onto the EDA. 2. Simultaneously press the Power button and the 1 and 9 keys. 3.
Getting Started 1-9 Locking the EDA Use the Device Lock feature to prevent use of the device. Note that when locked, the EDA does not respond to screen or keypad input. To lock the device, tap the Device unlocked icon. The icon changes to locked. Figure 1-6 Device Locked/Unlocked Icons To unlock the device and free it for use, tap Unlock. Figure 1-7 Unlock Device Window Tap Unlock on the Unlock Device window. SIM Card NOTE MC7004 and MC7094 only.
1 - 10 MC70 Integrator Guide • Any additional services to which you have subscribed. NOTE For more information about SIM cards, refer to the mobile phone service provider's documentation. To install the SIM card: 1. Press the red Power button to suspend the EDA. 2. Remove the battery. 3. Lift the SIM cover using the stylus tip. SIM Cover Figure 1-8 Lifting the SIM Cover 4. Insert the SIM card, as shown in Figure 1-9, with the cut edge of the card facing out and the contacts facing down.
Getting Started 1 - 11 Removing the Screen Protector A screen protector is applied to the EDA. Symbol recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. To remove the screen protector, lift the corner using a thin plastic card, such as a credit card, then carefully lift it off the display. Lift Screen Protector Corner Figure 1-10 Removing the Screen Protector ! CAUTION NOTE Do not use a sharp object to remove the protector.
1 - 12 MC70 Integrator Guide
Chapter 2 Accessories Chapter 2 Chapter 2 Accessories Introduction MC70 accessories provide a variety of product support capabilities. Accessories include cables, cradles, four-slot spare battery charger, headset, Multimedia Card (MMC), Secure Device (SD) card, Magnetic Stripe Reader (MSR), and trigger handle. Cables Snap one of the following cables on to the EDA to connect an external device. • USB Client charge cable • RS232 charge cable • DEX cable • Modem inverter cable • Autocharge cable.
2-2 MC70 Integrator Guide Snap-on Modules • MSR snaps on to the EDA and adds magstripe read capabilities. • TRG7000 Trigger Handle adds a gun-style handle with a scanning trigger to the EDA. Headset Use the headset to communicate via Voice-over-IP (VoIP) or for audio playback. To connect the headset, remove the plug from the headset jack at the top of the EDA and insert the headset connector. Contact a Symbol representative for compatible headsets.
Accessories 2 - 3 Figure 2-2 Card Cover Removal 3. Insert the card with the card contacts facing down and the cut corner on the right, until you feel a click. 4. Replace the housing cover and secure with the screws. To remove an MMC/SD card: 1. Power off the EDA. 2. Remove the card cover at the top of the EDA by loosening the screws and lifting the cover out of the slot. 3. Using the stylus, press and release the card to eject it. 4. Remove the card from the card slot. 5.
2-4 MC70 Integrator Guide Tap SDMMC Mode radio button if an SD or MMC card is installed in the SD slot. 3. Tap ok. 4. A dialog box displays indicating that the EDA must be reset for the change to take effect. Tap ok. 5. Perform a warm boot. Single Slot USB/Serial Cradle This section describes how to set up and use a Single Slot USB/Serial cradle with the EDA. For USB communication setup procedures see Chapter 3, ActiveSync. The Single Slot USB/Serial Cradle: • Provides 5.
Accessories 2 - 5 Charging the EDA Battery Connect the cradle to power. Insert the EDA into the EDA slot to begin charging. Charge Status LED Figure 2-5 EDA Battery Charging Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 2-6 Spare Battery Charging Battery Charging Indicators The Single Slot USB/Serial Cradle charges the EDA’s main battery and a spare battery simultaneously. The EDA’s Charge LED indicates the status of the battery charging in the EDA.
2-6 MC70 Integrator Guide The standard battery fully charges in approximately four hours and the extended capacity battery fully charges in approximately eight hours. Charging Temperature Charge batteries in temperatures from 0oC to 40oC (32°F to 104°F). Note that at temperatures above 35oC, charging is intelligently controlled by the EDA and the charging accessory in order to ensure safe operation and optimize long-term battery life.
Accessories 2 - 7 Power Port Ethernet Port Ethernet Switch, Router, or Hub Connection Figure 2-7 Four Slot Ethernet Cradle Connection Daisychaining Cradles Daisychain up to four Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. To daisychain more than one cradle: 1. Connect power to each cradle to daisychain. 2. Connect an Ethernet cable to Port 1 of the first cradle as shown in Figure 2-7. 3.
2-8 MC70 Integrator Guide Bandwidth Considerations when Daisychaining Each cradle added to the daisychain impacts the bandwidth provided to the inserted EDAs, particularly when the EDAs attempt to send and receive at data rates that exceed the bandwidth provided to the chain (typically 100 Mbps). If an EDA in a daisychained cradle does not use its bandwidth, that bandwidth is allocated to other inserted EDAs.
Accessories 2 - 9 Figure 2-10 IP Address Tab 4. In the IP address window, select the appropriate radio button: • Use server-assigned IP address or • Use specific IP address. Enter the IP address, Subnet mask, and Default gateway, as needed. 5. Tap the Name Servers tab. Figure 2-11 Name Servers Tab 6. Enter the appropriate DNS, Alt DNS, WINS, and Alt WINS server addresses. 7. Tap ok. Figure 2-12 Adapters Dialog Box 8. Tap ok to confirm the setup.
2 - 10 MC70 Integrator Guide 9. Tap ok to exit. Charging and Communication Insert the EDA into a slot to begin charging. Speed LED Link LED Figure 2-13 EDA Battery Charging LED Charging Indicators Charge LED The EDA’s charge LED shows the status of the battery charging in the EDA. See Table 1-2 on page 1-6 for charging status indications. The standard battery fully charges in approximately four hours and the extended capacity battery fully charges in approximately eight hours.
Accessories2 - 11 To accomplish this, for small periods of time, the EDA or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The EDA or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-2 on page 1-6. Wall Mount Bracket Use the optional Wall Mount Bracket to mount a four slot cradle to a wall. To attach the Wall Mount Bracket: 1.
2 - 12 MC70 Integrator Guide Four Slot Cradle Bottom Mounting Screw (2) Figure 2-15 Cradle Mounting Screws 2. Align the Wall Mount Bracket mounting tabs with the mounting slots in the back of the four slot cradle. Slip the two mounting tabs into mounting slots. 3. Swing the four slot cradle down onto the mounting bracket and align the mounting screws so that they fit into the screw slots. Wall Mount Bracket Screw Slots Power Supply Well Figure 2-16 Wall Mount Bracket 4.
Accessories2 - 13 VCD7000 Vehicle Cradle This section describes how to use a VCD7000 vehicle cradle with the EDA. For cradle installation and communication setup procedures refer to the MC70 Integrator Guide. Once installed in a vehicle, the cradle: • holds the EDA securely in place • provides power for operating the EDA • provides a serial port for data communication between an EDA and an external device (e.g.
2 - 14 MC70 Integrator Guide Connector Pin-Outs Table 2-4 Power Input Cable Pin Signal 1 Chassis ground (Bare Wire) 1 2 Chassis ground (Bare Wire) 3 V+ (Red Wire) 4 V+ (Red Wire) Connector on Power Cable Table 2-5 Serial Cable Pin Signal Pin Signal 1 DCD 5 GND 2 RxD 6 DSR 3 TxD 7 RTS 4 DTR 8 CTS 5 GND 9 5V_OUT CAUTION Connector on Serial Cable ROAD SAFETY - Do not use the EDA while driving. Park the vehicle first. Always ensure the EDA is fully inserted into the cradle.
Accessories2 - 15 1.2” 1.5” Figure 2-18 Vehicle Cradle Mounting Template 3. Position the cradle on the mounting surface. 4. Fasten it using four #8 washers and four #8-32 self-locking nuts. Do not install a VCD7000 Vehicle Cradle on or near an air bag cover plate or within an aerobic zone. Also, do not install it in a location that affects vehicle safety or driveability. CAUTION Power Connection Please read all of the following instructions before beginning.
2 - 16 MC70 Integrator Guide 2. Route the power input cable from the cradle’s power port to the connection point for the vehicle’s power source. CAUTION 3. The means of routing and securing the power input cable from the cradle through to the vehicle power source is extremely important. Hazards associated with improper wiring can be severe. To avoid unintentional contact between the wire and any sharp edges, provide the cable with proper bushings and clamping where it passes through openings.
Accessories2 - 17 To see if the cradle has power, insert the EDA. The Charging LED on the EDA blinks slowly to indicate charging and turns solid amber when the battery is completely charged. See Table 1-2 on page 1-6 for other indications. Serial Device Connection The EDA has a serial port on the bottom. When the EDA is inserted into the cradle, it connects to the cradle’s serial port. The EDA can then use the cradle’s serial port to communicate with an external device.
2 - 18 MC70 Integrator Guide Release Lever Figure 2-21 EDA Battery Charging CAUTION Ensure the EDA is fully inserted in the cradle. Lack of proper insertion may result in property damage or personal injury. Symbol Technologies, Inc. is not responsible for any loss resulting from the use of the products while driving. Removing the EDA To remove the EDA, hold back the release lever on the cradle and pull the EDA up and out of the cradle.
Accessories2 - 19 Battery Release Lever Extended Capacity Battery Shown Figure 2-23 Inserting the Spare Battery 2. Insert the spare battery in the spare battery charging slot in the cradle with the charging contacts facing up and to the rear of the cradle. 3. Release the battery release lever. The battery release lever locks the spare battery into place. To remove a spare battery, hold back the battery release lever and lift the battery from the spare battery slot.
2 - 20 MC70 Integrator Guide Table 2-6 Vehicle Cradle Spare Battery LED Charging Indicators Spare Battery LED (on cradle) Indication Slow Blinking Amber Spare battery is charging. Solid Amber Spare battery is fully charged. Fast Blinking Amber Charging error. Off Not charging. Charging Temperature Charge batteries in temperatures from 0oC to 40oC (32°F to 104°F).
Accessories2 - 21 Four Slot Spare Battery Charger This section describes how to use the Four Slot Spare Battery Charger to charge up to four EDA spare batteries. Use only a Symbol-approved power supply output rated 12 Vdc and minimum 3.33A. The power supply is certified to EN60950 with SELV outputs. Use of an alternative power supply will invalidate any approval given to this device and may be dangerous.
2 - 22 MC70 Integrator Guide Spare Battery Charging 1. Connect the charger to a power source. 2. Insert the spare battery into a spare battery charging well and gently press down on the battery to ensure proper contact. Spare Battery Spare Battery Charging LEDs (4) Figure 2-26 Four Slot Spare Battery Charger Battery Charging Indicators An amber LED is provided for each battery charging well. See Table 2-7 for charging status indications. The standard battery fully charges in approximately 2.
Accessories2 - 23 Table 2-7 Spare Battery LED Charging Indicators LED Indication Off No spare battery in slot; spare battery not placed correctly; cradle is not powered. Fast Blinking Amber Error in charging; check placement of spare battery. Slow Blinking Amber Spare battery is charging. Solid Amber Charging complete. Magnetic Stripe Reader (MSR) This section describes how to set up and use the snap-on MSR with the EDA.
2 - 24 MC70 Integrator Guide Using the MSR The MSR3000 sample application illustrates how an application handles MSR inputs (refer to Symbol Applications User’s Guide). To use the MSR: 1. Attach the MSR to the EDA. 2. Power on the EDA. 3. Tap Start > MC70 Demo > Test Apps > MSR MC70 or MSR Cameo to start the sample application. 4. Swipe the magnetic stripe card through the MSR, with the magnetic stripe on the card facing down.
Accessories2 - 25 Back Housing Bracket Figure 2-29 Removing Back Housing Bracket 4. Install the rubber headset jack dust cover onto the trigger handle cleat. 5. Align the trigger handle cleat onto the EDA. 6. Secure the trigger handle cleat to the EDA using the four screws saved during step 2. Figure 2-30 Installing the Cleat 7. Feed the handstrap through the handstrap slot and secure. Inserting the EDA into the Trigger Handle Slide the EDA into the Trigger Handle until it locks in place.
2 - 26 MC70 Integrator Guide Removing the EDA To remove the EDA, press the release down and pull the EDA forward. Release Figure 2-32 Removing the EDA Using a Cradle With the Trigger Handle you can charge the EDA and communicate with a host computer using either the serial charging cable or a cradle, or connect to a peripheral such as a printer.
Accessories2 - 27 To charge the EDA’s battery while the EDA is in the Trigger Handle, insert the EDA into either the Single Slot USB/Serial cradle or the Four Slot Ethernet cradle. Figure 2-34 Inserting the EDA Into the Cradle for Charging Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities.
2 - 28 MC70 Integrator Guide Figure 2-35 Cables (MC70 Connector) The communication/charge cables: • Provide the EDA with operating and charging power when used with the Symbol approved power supply. • Synchronize information between the EDA and a host computer. With customized or third party software, it can also synchronize the EDA with corporate databases. • Provide serial connection through the serial pass-through port for communication with a serial device, such as a host computer.
Accessories2 - 29 Battery Charging The communication/charge cables can charge the EDA battery and supply operating power. To charge the EDA battery: 1. Connect the communication/charge cable power input connector to the Symbol approved power source. 2. Slide the bottom of the EDA into the connector end of the communication/charge cable and gently press in until it latches into the EDA. The EDA amber Charge LED indicates the EDA battery charging status.
2 - 30 MC70 Integrator Guide
Chapter 3 ActiveSync Chapter 3 Chapter 3 ActiveSync Introduction To communicate with various host devices, install Microsoft ActiveSync (version 4.1 or higher) on the host computer. Use ActiveSync to synchronize information on the mobile computer with information on the host computer. Changes made on the mobile computer or host computer appear in both places after synchronization. NOTE When a mobile computer with Windows Mobile 5.
3-2 MC70 Integrator Guide Mobile Computer Setup NOTE Microsoft recommends installing ActiveSync on the host computer before connecting the mobile computer. The mobile computer can be set up to communicate either with a serial connection or a USB connection. Chapter 2, Accessories provides the accessory setup and cable connection information for use with the mobile computer. The mobile computer communication settings must be set to match the communication settings used with ActiveSync. 1.
ActiveSync 3-3 Figure 3-2 ActiveSync Window NOTE 2. Assign each mobile computer a unique device name. Do not try to synchronize more than one mobile computer to the same name. In the ActiveSync window, select File > Connection Settings. The Connection Settings window appears. Figure 3-3 Connection Settings Window 3. Select the appropriate check box for the type of connection used. 4. Select the Show status icon in Taskbar check box. 5. Select OK to save any changes made.
3-4 MC70 Integrator Guide Figure 3-4 Synchronization Setup Wizard Window 2. Click Next. Figure 3-5 Synchronization Directly With a Server Window 3. Select the check box to synchronize with a server running Microsoft Exchange if applicable. 4. Click Next.
ActiveSync Figure 3-6 Synchronization Option Window 5. Select the appropriate settings and click Next. Figure 3-7 Wizard Complete Window 6. Click Finish.
3-6 MC70 Integrator Guide Figure 3-8 ActiveSync Connected Window During the first synchronization, information stored on the mobile computer is copied to the host computer. When the copy is complete and all data is synchronized, the mobile computer can be disconnect from the host computer. NOTE The first ActiveSync operation must be performed with a local, direct connection. Windows Mobile retains partnerships information after a cold boot.
Chapter 4 Application Deployment for Mobile 5.0 Chapter 4 Chapter 4 Application Deployment for Mobile 5.0 Introduction This chapter describes new features in Windows Mobile 5.0 including new security features, how to package applications, and procedures for deploying applications onto the EDA. Security The MC70 EDAs implement a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust.
4-2 MC70 Integrator Guide To support the broadest number of deployments, third-party software developers should perform the following when releasing software for a Windows Mobile 5.0 devices: • Sign all their EXEs & DLLs with their private key • Provide the corresponding public certificate to end-users so that it can be installed into Privileged Execution Trust Certificate Store. If the software is installed via a .CAB file, developer should also: • Sign the .
Application Deployment for Mobile 5.0 4-3 Installing Certificates Use XML provisioning to query and delete certificates from certificate stores.
4-4 MC70 Integrator Guide Remote API Security The Remote API (RAPI) enables applications that run on a desktop to perform actions on a remote device. RAPI provides the ability to manipulate the file system on the remote device, including the creation and deletion of files and directories. By default, Symbol ships with RAPI in the restricted mode. Certain tools, such as RAPIConfig, may not work properly. Refer to the Windows Mobile Version 5.
Application Deployment for Mobile 5.0 4-5 Installation Using Storage Card To install an application package: • Copy the package CAB file to a storage card using an appropriate storage card reader. • Install the storage card into the EDA. See Multi Media Card (MMC) / Secure Digital (SD) Card on page 2-2 for more information. • On the EDA, open File Explorer. • Open the Storage Card directory. • Tap the package CAB file. The application installs on the EDA.
4-6 MC70 Integrator Guide When it finds the appropriate file, it loads the package onto the EDA. A progress bar displays until the update completes. 8. The EDA re-boots. 9. The calibration screen appears. NOTE When initiating an update via a boot sequence, the update loader looks for updates first on the root of an installed SD card and then in the \temp folder on the EDA’s persistent storage volume. A response file, pkgs.lst, indicates which files to update. In most cases, Symbol provides this pkgs.
Application Deployment for Mobile 5.0 4-7 certain privileges (roles). Some registry keys require you to simply be an Authenticated User, while other registry keys require you to be a Manager. Refer to the Microsoft Windows Mobile 5.0 Help file, Metabase Settings for Registry Configuration Service Provider section, for the default role settings in Windows Mobile 5.0. For those registry settings that require the Manager role, the CPF file must be signed with a privileged certificate installed on the device.
4-8 MC70 Integrator Guide The following example uses XML provisioning to perform the same task: SampleReg.xml CopyFiles CopyFiles copies files from one folder to another on a clean boot. During a clean boot CopyFiles looks for files with a .
Application Deployment for Mobile 5.0 4-9 Storage Mobile 5.0 contains three types of file storage: • Random Access Memory (RAM) • Persistent Storage • Application folder. Random Access Memory Executing programs use RAM to store data. Data stored in RAM is lost upon a warm boot. RAM also included a volatile file storage area called Cache Disk. Volatile File Storage (Cache Disk) Windows Mobile 5.
4 - 10 MC70 Integrator Guide Application Folder The Application folder is a super-persistent storage that is persistent even after a clean boot. Accessing data in the Application folder is slower than accessing persistent storage. The Application folder is used for deployment and device-unique data. For example, network profiles can be stored in the Application folder so that connection to the network is available after a cold boot. The Application folder is approximately 20 MB (formatted).
Application Deployment for Mobile 5.0 4 - 11 Figure 4-1 Main SCM Window Menu Functions Use the main menu to access the program functionality described in Table 4-1. Table 4-1 SCM Menu Functions Menu Item Description File Menu Open Config File Open a saved configuration file (.SCD). Save Config Changes Save changes to the currently loaded configuration file. Restore All Defaults Restore all parameter values to the default state.
4 - 12 MC70 Integrator Guide Parameter State Indicators The first column of the data table displays parameter state indicators. The state indicators display one of the states in Table 4-2 for a particular parameter: Table 4-2 Parameter Status Indicators Icon Indicator Description Modified This parameter was changed from its initial factory setting. Invalid This parameter is not valid for the selected device type.
Application Deployment for Mobile 5.0 4 - 13 Rapid Deployment Client The Rapid Deployment (RD) Client facilitates software downloads to a EDA from a Mobility Services Platform (MSP) Console’s FTP server. The MSP Console is a web-based interface to the wireless infrastructure monitoring and management tools provided by the MSP Lite or MSP Enterprise server. When software packages are transferred to the FTP server, the EDA on the wireless network can download them.
4 - 14 MC70 Integrator Guide Table 4-4 Rapid Deployment Window Text Box/Button Description Please scan all of the bar codes... Displays the status of a scanned bar code. Waiting - indicates the EDA is ready to scan a bar code. OK - indicates the EDA successfully scanned a bar code. (The Indicator LED bar on the EDA turns green and a beep sounds). If there are no bar codes left to scan, the Rapid Deployment Configuring window displays. Bar codes left to scan...
Application Deployment for Mobile 5.0 4 - 15 Ready to Scan No Bar Codes Left to Scan Ready to Scan Bar Codes Left to Scan are Listed Figure 4-4 Rapid Deployment Window 3. 4. Scan the appropriate bar code(s) to complete the configuration and/or download. a. A PDF417 bar code (2-D bar code) can contain all download data in a single bar code. In this case, only one bar code may be required to scan. b. Multi-part linear bar codes (1-D bar codes) can require scanning several bar codes.
4 - 16 MC70 Integrator Guide • The designated package(s) are downloaded from the FTP server. AirBEAM Smart The AirBEAM Smart product allows specially designed software packages to be transferred between a host server and Symbol wireless handheld devices. Before transfer, AirBEAM Smart checks and compares package versions, so that only updated packages are loaded.
Application Deployment for Mobile 5.0 4 - 17 AirBEAM Smart Client The AirBEAM Smart Client resides on the handheld EDA. It is configured with the server access information, the names of the packages to be downloaded and other controlling parameters. When the AirBEAM Smart Client is launched, the device connects to the specified FTP server and checks the packages it is configured to look for. If the package version was updated, the client requests the transfer.
4 - 18 MC70 Integrator Guide Packages(1) Tab Use this tab to specify the package name of the first four of eight packages to load during the AirBEAM synchronization process. The specified package name must correspond to a package available on the specified package server. Figure 4-7 Package (1) Tab Table 4-5 Package (1) Tab Field Description Package 1 Package name of the first of eight packages. This is an optional field. Package 2 Package name of the second of eight packages.
Application Deployment for Mobile 5.0 4 - 19 Packages(2) Tab Use this tab to specify the package name of the last four of eight packages to load during the AirBEAM synchronization process. The specified package name must correspond to a package available on the specified package server. Figure 4-8 Package (2) Tab Table 4-6 Package (2) Tab Field Description Package 5 Package name of the fifth of eight packages. This is an optional field. Package 6 Package name of the sixth of eight packages.
4 - 20 MC70 Integrator Guide Server Tab Use this tab to specify the configurations of the server to which the client connects during the package synchronization process. Figure 4-9 Server Tab Table 4-7 Server Tab Field Description IP Address The IP Address of the server. It may be a host name or a dot notation format. Directory The directory on the server that contains the AirBEAM package definition files.
Application Deployment for Mobile 5.0 4 - 21 Misc(1) Tab Use this tab to configure various miscellaneous features. Figure 4-10 Misc(1) Tab Table 4-8 Misc(1) Tab Field Description Auto-load Use this drop-down list to specify how to invoke the AirBEAM Smart Client when the client device is rebooted. Options are: Disable: the AirBEAM Smart Client is not invoked automatically during the boot sequence.
4 - 22 MC70 Integrator Guide Misc(2) Tab Use this tab to configure various miscellaneous features. Figure 4-11 Misc(2) Tab Table 4-9 Misc(2) Tab Field Description Auto-retry Use this field to specify whether the AirBEAM Smart Client automatically retries if synchronization fails. If this feature is enabled, the AirBEAM Smart Client displays a pop-up dialog indicating the retry attempt. The pop-up dialog appears for the number of seconds specified in the Retry Delay field.
Application Deployment for Mobile 5.0 4 - 23 Misc(3) Tab Use this tab to configure various miscellaneous features. Figure 4-12 Misc(3) Tab Table 4-10 Misc(3) Tab Field Description Use DHCP server This check box control specifies whether the AirBEAM Smart Client uses the DHCP response option 66 to specify the IP address of the FTP/TFTP server. If enabled, special RF network registry settings are required to force the DHCP server to return the "TFTP server name" field (option 66).
4 - 24 MC70 Integrator Guide Figure 4-13 AirBEAM Synchronize Window • The Status List displays messages that indicate the synchronization progress. • Tap OK to return to the Main Menu. This button remains inactive until synchronization completes. • Tap Retry to restart synchronization. This button is active only if there is an error during synchronization.
Chapter 5 MC7004/94 - GSM Configuration Chapter 5 Chapter 5 MC7004/94 - GSM Configuration Introduction This chapter explains how to verify MC7004/94 service on an Enhanced Data rates for Global Evolution (EDGE) wireless network and establish settings. EDGE is also known as Enhanced General Packet Radio Service (EGPRS). EDGE networks deliver mobile voice and data services, such as Short Message Service (SMS)/Text Messaging, with full roaming capabilities across the world.
5-2 MC70 Integrator Guide 7. Configure settings (page 5-7). 8. Use the phone. MC7004/94 Service Verification MC7004/94 phone and data services require a live SIM card, obtained from a service provider, installed in the EDA phone/EDA. The SIM card has embedded circuitry on one side of its surface which, when inserted into an EDA phone, provides phone service on an EDGE network.
MC7004/94 - GSM Configuration 5-3 Figure 5-2 Phone Settings Window - Network Tab b. Ensure the service provider’s network appears in the Current network: field. c. If the network does not appear, tap Find Network. If the network still does not appear, verify that the SIM card was installed correctly. If it was, and no network appears, contact the service provider. Configuring a GPRS Data Connection A GPRS data connection allows Internet access across a wireless network.
5-4 MC70 Integrator Guide 3. Under My ISP select Add a new modem connection. Figure 5-4 Connections Window - Make New Connection 4. Enter a connection name in the Enter a name for the connection: text box. 5. Select Cellular Line (GPRS) from the Select a modem: drop-down list. 6. Tap Next. Figure 5-5 Connections Window - Access Point Name 7. Enter the APN from the service provider in the Access point name: text box. 8. Tap Next.
MC7004/94 - GSM Configuration Figure 5-6 Connections Window - User Name & Password 9. Tap Finish (user name and password are not required). 10. Tap ok to exit Connections. Establishing a Data Connection 1. Install a SIM card in the EDA. 2. Configure a GPRS data connection. See Configuring a GPRS Data Connection on page 5-3. 3. Tap at the top of the screen. Figure 5-7 Connectivity Dialog 4. Tap Settings. 5. Tap Managing existing connections. 6.
5-6 MC70 Integrator Guide Figure 5-8 Data Connection 7. Select Connect. Figure 5-9 Connecting Using IDEN Packet Data Modem 8. If the SIM card is protected with a Personal Identification Number (PIN), a dialog box pops up requesting the appropriate PIN to unlock the SIM card. In this case, enter the PIN and tap ok. NOTE 9. Place emergency calls at any time, without entering a PIN or a SIM card.
MC7004/94 - GSM Configuration 5-7 Figure 5-10 Connectivity Dialog Box 2. Tap Disconnect. NOTE Tapping Disconnect during an active data transfer (e.g., downloading a web page) automatically reconnects the GPRS connection. You cannot disconnect the GPRS connection until the data transfer is complete. GPRS Settings Use the Phone Settings window to customize settings, such as the ring type and ring tone for incoming calls, security options (GPRS), and other options depending on the type of service.
5-8 MC70 Integrator Guide Sounds 1. Phone Number automatically displays on the Phone tab when a live SIM card is installed. 2. Select a ring type from the Ring type: drop-down list. The ring type changes the way the EDA rings when you receive an incoming call. Regardless of the ring type selected, a dialog box appears on the EDA’s display for incoming calls. 3. Select a ring tone for incoming calls from the Ring tone: drop-down list. To hear a sample of the selected ring tone, tap NOTE 4. .
MC7004/94 - GSM Configuration 5-9 Changing a PIN 1. From the Phone tab (Figure 5-11), tap Change PIN. 2. Use the touch keypad to enter the current PIN. 3. Tap Enter. 4. Use the touch keypad to enter a new four to eight digit PIN. 5. Tap Enter. 6. Reenter the new PIN for confirmation and tap Enter. 7. Tap ok to confirm the change. Disabling a PIN 1. From the Phone tab (Figure 5-11), deselect the Require PIN when phone is used check box. 2. Use the touch keypad to enter the current PIN. 3.
5 - 10 MC70 Integrator Guide 3. Change services settings as follows. Call Barring (Call Blocking) Use call barring to block certain types of incoming and/or outgoing calls. Select the type of incoming and/or outgoing calls to block. Figure 5-14 Call Barring/Call Blocking Caller ID Enable caller ID to reveal the identity of the person making an outgoing call. Select the Everyone radio button to always display the caller ID.
MC7004/94 - GSM Configuration 5 - 11 • To forward incoming calls to a different phone number based on a specific situation, select one or more of the check boxes under Forward phone calls only if:. • No answer: enter the phone number to receive forwarded calls only when the phone cannot be answered. Then select a time period from the Forward after: drop-down list. Options are 5, 10, 15, 20, 25, and 30 seconds.
5 - 12 MC70 Integrator Guide Figure 5-18 Voice Mail and Text Messages Fixed Dialing Use Fixed Dialing to restrict the phone to dial only the phone number(s) or area code(s) specified in a Fixed Dialing list. 1. Select Fixed Dialing and tap Get Settings. Figure 5-19 Fixed Dialing Window 2. Select the Enable fixed dialing check box. 3. To add a number to the list, tap Menu > Add. 4. Enter the phone number or area code to restrict and tap Done. 5.
MC7004/94 - GSM Configuration 5 - 13 The network the EDA currently uses appears in the Current network: field at the top of the window. Changing Networks Manually 1. Tap Start > Settings > Personal tab > Phone icon > Network tab or Start > Phone > Menu > Options > Network tab. Figure 5-20 MC70 Phone Window - Network Tab 2. From the Network selection drop-down list, select Manual. Figure 5-21 Choose Network 3. From the Choose Network window, select the network to use. 4. Tap OK.
5 - 14 MC70 Integrator Guide Figure 5-22 MC70 Phone Window - Network Tab 2. Tap Find Network. Figure 5-23 Choose Network 3. From the Choose Network window, select the network to use. 4. Tap OK.
MC7004/94 - GSM Configuration 5 - 15 Setting Preferred Networks Set networks in a preferred order of access. Setting preferred networks allows the EDA to access a second preferred network if the first is unavailable. 1. Tap Start > Settings > Personal tab > Phone icon > Network tab or Start > Phone > Menu > Options > Network tab. Figure 5-24 MC70 Phone Window - Network Tab 2. Tap Set Networks to view all available networks. Figure 5-25 Preferred Networks 3.
5 - 16 MC70 Integrator Guide Phone Info Use the Phone Info tab to view hardware and software information about the phone. 1. Tap Start > Settings > Personal tab > Phone icon > Phone Info tab or Start > Phone > Menu > Options > Phone Info tab. Figure 5-26 MC70 Phone Window - Phone Info Tab 2. Tap ok to exit settings. Band NOTE 1. The Band tab appears only when MC70 configuration is installed on the EDA.
MC7004/94 - GSM Configuration 5 - 17 2. Select the 850 MHz Enabled check box to enable the radio to hand over in the band of 850MHz (in addition to PCS1900MHz/DCS1800MHz). 3. Disable Handover Enhancement only for some special networks outside of the United States and Europe. 4. Tap ok to exit settings.
5 - 18 MC70 Integrator Guide
Chapter 6 MC7095 - CDMA Configuration Chapter 6 Chapter 6 MC7095 - CDMA Configuration Introduction This chapter explains how to activate an MC7095 EDA on a CDMA wireless network and establish settings. CDMA is a form of wireless multiplexing in which data (e.g., Short Message Service) can be sent over multiple frequencies simultaneously, optimizing the use of available bandwidth.
6-2 MC70 Integrator Guide MC7095 CDMA Phone Activation CDMA phone service is available from a number of service providers including Sprint® and Verizon®. In addition to service activation for each provider, various settings may be required for the MC7095 to operate as a phone. Sprint Activation To activate the phone using Sprint service: 1. Contact Sprint to obtain a 6-digit activation code, also known as the Master Subsidy Lock (MSL) code, Mobile Directory Number (MDN) and Mobile Station ID (MSID). 2.
MC7095 - CDMA Configuration 6-3 Figure 6-3 Sprint Activation Wizard - MDN and MSID 7. Enter the MDN and MSID. The MDN and MSID are the area code and phone number received from the service provider. 8. Tap Next >. Figure 6-4 Sprint Activation Wizard - Confirmation 9. Verify that the MDN and MSIN numbers entered are correct, tap Yes to confirm.
6-4 MC70 Integrator Guide 10. Tap Finish to complete activation. The phone can be used in approximately four hours. Sprint Activation Test Approximately four hours after activation is completed, test the service. 1. Tap Start > Phone. Figure 6-6 Sprint Phone Window 2. Ensure the Sprint name displays on the window. 3. Make a voice call to ensure activation was successful. NOTE 4. If activation was not successful, contact the service provider.
MC7095 - CDMA Configuration 6-5 Figure 6-7 Verizon Activation Wizard 3. Tap Start to connect to the Verizon Wireless Network to automate activation. Automated activation provides all required codes and identification numbers over the network. No additional activation setup is required. Figure 6-8 Activation in Progress Figure 6-9 Activation Complete 4. Tap Finish to close the Activation Wizard.
6-6 MC70 Integrator Guide 5. Tap Finish to complete activation. The phone can be used in approximately four hours, depending on the network provider load. Verizon Activation Test Approximately four hours after activation is completed, test the service. 1. Tap Start > Phone. Figure 6-10 Verizon Phone Window 2. Ensure the Verizon name displays on the window. 3. Make a voice call to ensure activation was successful. NOTE If activation was not successful, contact the service provider.
MC7095 - CDMA Configuration 6-7 Establishing a CDMA Data Connection A CDMA data connection allows Internet access across a wireless network. Data connection is pre-packaged with service accounts. To verify active data service: 1. Tap to display the Connectivity dialog. Figure 6-11 Data Connection 2. Tap #777 for a data connection using the Cellular Line. or 3. Tap Start > Internet Explorer. 4. In the address bar, enter the URL for a web site. 5. Press Enter.
6-8 MC70 Integrator Guide CDMA Settings Use the Phone Settings window to customize CDMA phone settings, such as the ring type and ring tone for incoming calls and other options depending on the type of service. Phone Use the Phone tab to customize ring type, ring tone and keypad tone when entering phone numbers. 1. Tap Start > Settings > Personal tab > Phone icon > Phone tab. or Start > Phone > Menu > Options > Phone tab. Figure 6-12 Phone Window - Phone Tab 2.
MC7095 - CDMA Configuration 8. 6-9 Tap ok to exit settings. NOTE Turning off sounds saves power and prolongs battery life. Location Settings Use the Location tab to allow the network to detect the position of the MC7095’s radio. 1. Tap Start > Settings > Personal tab > Phone icon > Location Settings tab. or Start > Phone > Menu > Options > Location Settings tab. Figure 6-13 Phone Window - Location Tab (Typical) 2.
6 - 10 MC70 Integrator Guide Figure 6-14 Phone Window - Sprint Data Tab 2. Tap Repair Connectiod to reset PCS Vision connection settings. Figure 6-15 Reset Connection Settings Dialog 3. Tap Yes. Figure 6-16 Reset Connection Completed Dialog 4. Tap ok. 5. Tap Provision to manually start IP-based Over-The-Air (IOTA) provisioning.
MC7095 - CDMA Configuration 6 - 11 IOTA is used to provision various data elements such as Wireless Application Protocol (WAP) configuration parameters and roaming lists to the MC7095 over-the-air. It is also used to provision other elements such as applications and firmware. 6. Tap ok to exit settings. Verizon Data Settings Use the Data tab to reset connection settings for national access. 1. Tap Start > Settings > Personal tab > Phone icon > Data Settings tab.
6 - 12 MC70 Integrator Guide Figure 6-18 Phone Window - Data Tab 2. Tap Reset Connection to reset connection settings for the 3G connection. 3. Tap Yes. 4. Tap ok. 5. Tap ok to exit settings. System Settings Use the System Settings tab to select roaming options. Tap Start > Settings > Personal tab > Phone icon > System Settings tab. or Start > Phone > Menu > Options > System tab. Sprint System Sprint Figure 6-19 Phone Window - System Settings Tab - Sprint 1.
MC7095 - CDMA Configuration 6 - 13 • Select the Automatic radio button to allow the phone to automatically seek a roaming network where the Sprint Nationwide PCS Network is not available. Automatic roaming is available where Sprint implemented roaming with other wireless carriers. • Select the Sprint radio button to allow the phone to automatically seek a roaming network within the Sprint Nationwide PCS Network only.
6 - 14 MC70 Integrator Guide Additional Service Provider System Figure 6-21 Phone Window - System Settings Tab - Additional 1. System Select allows the user to change the system roaming preference of the radio in order to control the type of network the radio can lock onto for service. • Select the Automatic radio button to allow the radio to lock onto networks based on the provisioning of the radio.
MC7095 - CDMA Configuration 6 - 15 Figure 6-22 MC7095 Phone Window - Phone Info Tab 2. Tap ok to exit settings. Services Depending on the type of subscribed phone services, the following services may be available: call barring, caller ID, call forwarding, call waiting, voice mail and Short Message Service (SMS). Call Barring (Call Blocking) Call barring blocks certain types of incoming and/or outgoing calls. This service is setup when an account is opened with the service provider.
6 - 16 MC70 Integrator Guide 1. Enter *720 on the phone keypad. 2. Tap Talk. 3. A beep sounds indicating deactivation. 4. Tap End. Call Waiting Call waiting notifies the user of an incoming call when the phone is in a phone session. This service is setup when an account is opened with the service provider. Voice Mail and Short Message Service (SMS) This service is setup when an account is opened with the service provider.
Chapter 7 Wireless Applications Chapter 7 Chapter 7 Wireless Applications Introduction Wireless Local Area Networks (LANs) allow mobile computers to communicate wirelessly and send captured data to a host device in real time. Before using the EDA on a WLAN, the facility must be set up with the required hardware to run the wireless LAN and the EDA must be configured. Refer to the documentation provided with the access points (APs) for instructions on setting up the hardware.
7-2 MC70 Integrator Guide Signal Strength Icon The Signal Strength icon in the task tray indicates the EDA’s wireless signal strength as follows: Table 7-1 Wireless Applications Icons, Signal Strength Descriptions Icon Status Action Excellent signal strength Wireless LAN network is ready to use. Very good signal strength Wireless LAN network is ready to use. Good signal strength Wireless LAN network is ready to use. Fair signal strength Wireless LAN network is ready to use.
Wireless Applications 7-3 Figure 7-3 Enable Radio Find WLANs Application Use the Find WLANs application to discover available networks in the vicinity of the user and EDA. To open the Find WLANs application, tap the Signal Strength icon > Find WLANs. The Find WLANs window displays. Figure 7-4 Find WLANs Window NOTE The Find WLANs display is limited to 32 items (ESSIDs or MAC addresses). A combination of up to 32 ESSIDs/APs may be displayed.
7-4 MC70 Integrator Guide . Table 7-2 Signal Strength Icon Icon Description Excellent signal Very good signal Good signal Fair signal Poor signal Out of range or no signal Table 7-3 Encryption Icon Icon Description No encryption. WLAN is an infrastructure network. WLAN is an Ad-Hoc network. WLAN access is encrypted and requires a password. Tap-and-hold on a WLAN network to open a pop-up menu which provides two options: Connect and Refresh. Select Refresh to refresh the WLAN list.
Wireless Applications 7-5 Table 7-4 Profile ID Fields Field Description Name The name and (WLAN) identifier of the network connection. Enter a user friendly name for the mobile computer profile used to connect to either an AP or another networked computer. Example: The Public LAN. ESSID The ESSID is the 802.11 extended service set identifier. The ESSID is 32-character (maximum) string identifying the WLAN, and must match the AP ESSID for the EDA to communicate with the AP.
7-6 MC70 Integrator Guide Table 7-5 Operating Mode Fields Field Description Operating Mode Select Infrastructure to enable the EDA to transmit and receive data with an AP. Infrastructure is the default mode. Select Ad Hoc to enable the EDA to form its own local network where mobile computers communicate peer-to-peer without APs using a shared ESSID. Country Country determines if the profile is valid for the country of operation.
Wireless Applications 7-7 Ad-Hoc Use the Ad-Hoc dialog box to select the required information to control Ad-Hoc mode. This dialog box does not appear if you selected Infrastructure mode. To select Ad-Hoc mode: 1. Select a channel number from the Channel drop-down list. The default is Channel 1 (2412 MHz). Figure 7-7 Ad-Hoc Settings Dialog Box 2. Tap Next. The Authentication dialog box displays. Authentication Use the Authentication dialog box to configure authentication.
7-8 MC70 Integrator Guide Tunneled Authentication Use the Tunneled Authentication dialog box to select the tunneled authentication options. There are different selections available for PEAP or TTLS authentication. Figure 7-9 Tunneled Authentication Dialog Box To select a tunneled authentication type: 1. Select a tunneled authentication type from the drop-down list. See Table 7-7 and Table 7-8. 2. Select the User Certificate check box if a certificate is required.
Wireless Applications 7-9 Table 7-8 lists the TTLS tunneled authentication options. Table 7-8 TTLS Tunneled Authentication Options TTLS Tunneled Authentication Description CHAP Challenge Handshake Authentication Protocol (CHAP) is one of the two main authentication protocols used to verify the user name and password for PPP Internet connections. CHAP is more secure than PAP because it performs a three way handshake during the initial link establishment between the home and remote machines.
7 - 10 MC70 Integrator Guide User Certificate Installation To install a user certificate (EAP TLS only) and a server certificate for EAP TLS and PEAP authentication: 1. Tap Install Certificate. The Credentials dialog box appears. Figure 7-11 Credentials Dialog Box 2. Enter the User:, Pwd: (password), and Server: information in their respective text boxes. 3. Tap Retrieve. A Progress dialog indicates the status of the certificate retrieval. 4. Tap ok to exit.
Wireless Applications 7 - 11 Figure 7-13 Browse Server Certificates Press the ENT key to change the default path or extension (and search a new path). Select a certificate before tapping the Install button. Figure 7-14 Confirmation Dialog Box A confirmation dialog verifies the installation. If the information in this dialog is correct, tap the Yes button, If the information in this dialog is not correct tap the No button. The wizard returns to the Installed Server Certs dialog box.
7 - 12 MC70 Integrator Guide Figure 7-15 Prompt for Login at Dialog Box If the EDA does not have the credentials, you are prompted to enter a username and password. If the EDA has the credentials (previous entered via a login dialog box), it uses these credentials unless the caching options require the EDA to prompt for new credentials. If you entered the credentials via the profile, the EDA does not prompt for new credentials. Table 7-9 lists the caching options.
Wireless Applications 7 - 13 1. Tap the Interval radio button to check credentials at a set time interval. 2. Enter the value in minutes in the Min box. 3. Tap the At (hh:mm) radio button to check credentials at a set time. 4. Tap Next. The At Time dialog box appears. Figure 7-17 At Time Dialog Box 5. Enter the time using the 24 hour clock format in the (hh:mm) box. 6. Tap > to move the time to the right. Repeat for additional time periods. 7. Tap Next. The User Name dialog box displays.
7 - 14 MC70 Integrator Guide 3. Tap Next. The Encryption dialog box displays. See Encryption on page 7-14. Advanced Identity Use the Advanced ID dialog box to enter the 802.1X identity to supply to the authenticator. This value can be 63 characters long and is case sensitive. In TTLS and PEAP, it is recommended entering the identity anonymous (rather than a true identity) plus any desired realm (e.g., anonymous@myrealm). A user ID is required before proceeding.
Wireless Applications 7 - 15 Table 7-10 Encryption Options Encryption Description Open Select Open (the default) when no data packet encryption is needed over the network. Selecting this option provides no security for data transmitting over the network. 40-Bit WEP Select 40-Bit WEP to use 40-bit key length WEP encryption. WEP keys are manually entered in the edit boxes. Only the required number of edit boxes for a key length is displayed (10 Hex digit value for 40-bit keys).
7 - 16 MC70 Integrator Guide Key Entry Page If you select either 40-Bit WEP or 128-Bit WEP the wizard proceeds to the key entry dialog box unless the Use Passkey check box was selected in the Encryption dialog box (see Figure 7-21 on page 7-14). The Key Entry dialog box will be shown only if the authentication is set to None.To enter the key information: 1. Enter the 40-bit or 128-bit keys into the fields. 2. Tap Next.
Wireless Applications 7 - 17 Figure 7-24 IP Config Tab (DHCP) Table 7-12 IP Mode Options Encryption Description DHCP Select Dynamic Host Configuration Protocol (DHCP) from the IP Mode drop-down list to obtain a leased IP address and network configuration information from a remote server. DHCP is the default setting for the EDA profile. When DHCP is selected, the IP address fields are read-only.
7 - 18 MC70 Integrator Guide Select the Advanced check box, then tap NEXT to display the Advanced Address Entry dialog box. Enter the Gateway, DNS, and WINS address. Tap NEXT without selecting the Advanced check box to display the Transmit Power dialog box. Figure 7-26 Advanced Address Entry Dialog Box The IP information entered in the profile is only used if you selected the Enable IP Mgmt check box in the Options > System Options dialog box (System Options on page 7-34).
Wireless Applications 7 - 19 Table 7-15 Transmit Power Dialog Box (Infrastructure Mode) Field Description Automatic Select Automatic (the default) to use the AP power level. Power Plus Select Power Plus to set the EDA transmission power one level higher than the level set for the AP. Figure 7-28 Transmit Power Dialog Box (Ad-Hoc Mode) Table 7-16 Power Transmit Options (Ad-Hoc Mode) Field Description Full Select Full power for the highest transmission power level.
7 - 20 MC70 Integrator Guide Figure 7-29 Battery Usage Dialog Box NOTE Power consumption is also related to the transmit power settings. Table 7-17 Battery Usage Options Field Description CAM Continuous Aware Mode (CAM) provides the best network performance, but yields the shortest battery life. Fast Power Save Fast Power Save (the default) performs in the middle of CAM and MAX Power Save with respect to network performance and battery life.
Wireless Applications 7 - 21 Icons next to each profile identify the profile’s current state. Table 7-18 Profile Icons Icon No Icon Description Profile is not selected, but enabled. Profile is disabled. Profile is cancelled. A cancelled profile is disabled until a connect or login function is performed through the configuration editor. Profile is in use and describes an infrastructure profile not using encryption. Profile is in use and describes an infrastructure profile using encryption.
7 - 22 MC70 Integrator Guide Figure 7-32 Manage Profiles Tap and hold a profile and select Connect from the pop-up menu to set this as the active profile. Once selected, the EDA uses the authentication, encryption, ESSID, IP Config, and power consumption settings configured for that profile. Editing a Profile Tap and hold a profile and select Edit from the pop-up menu to display the Profile Wizard where you can set the ESSID and operating mode for the profile.
Wireless Applications 7 - 23 Ordering Profiles Tap and hold a profile from the list and select Move Up or Move Down to order the profile. If the current profile association is lost, the EDA attempts to associate with the first profile in the list, then the next, until it achieves a new association. NOTE Profile Roaming must be enabled. Export a Profile To export a profile to a registry file, tap and hold a profile from the list and select Export from the pop-up menu.
7 - 24 MC70 Integrator Guide Wireless Status Application To open the Wireless Status window, tap the Signal Strength icon > Wireless Status. The Wireless Status window displays information about the wireless connection. Figure 7-35 Wireless Status Window The Wireless Status window contains the following options. Tap the option to display the option window. • Signal Strength - provides information about the connection status of the current wireless profile.
Wireless Applications 7 - 25 Figure 7-36 Signal Strength Window After viewing the Signal Strength window, tap the back button to return to the Wireless Status window. Table 7-19 Signal Strength Status Field Signal Description Displays the Relative Signal Strength Indicator (RSSI) of the signal transmitted between the AP and EDA. As long as the Signal Quality icon is green the AP association is not jeopardized.
7 - 26 MC70 Integrator Guide Table 7-19 Signal Strength Status (Continued) Field Description Association Count Displays the number of APs the EDA connects to while roaming. AP MAC Address Displays the MAC address of the AP to which the EDA is connected. Transmit Rate Displays the current rate of the data transmission. Current Profile Window The Current Profile window displays basic information about the current profile and connection settings. This window updates every two seconds.
Wireless Applications 7 - 27 IPv4 Status Window The IPv4 Status window displays the current IP address, subnet, and other IP related information assigned to the EDA. It also allows renewing the address if the profile is using DHCP to obtain the IP information. Tap Renew to initiate a full DHCP discover. The IPv4 Status window updates automatically when the IP address changes. To open the IPv4 Status window, tap IPv4 Status in the Wireless Status window.
7 - 28 MC70 Integrator Guide Table 7-21 IPv4 Status Fields (Continued) Field Description Lease Expires Displays the date that the IP address expires and a new IP address is requested. DNS Displays the IP address of the DNS server. WINS WINS is a Microsoft Net BIOS name server. WINS eliminates the broadcasts needed to resolve computer names to IP addresses by providing a cache or database of translations.
Wireless Applications 7 - 29 Versions Window The Versions window displays software, firmware, and hardware version numbers. This window only updates when it is displayed. There is no need to update constantly. The content of the window is determined at runtime, along with the actual hardware and software to display in the list. Executable paths of the software components on the list are defined in registry, so that the application can retrieve version information from the executable.
7 - 30 MC70 Integrator Guide Wireless Diagnostics Application The Wireless Diagnostics application window provides links to perform ICMP Ping, Trace Routing, and Known APs. To open the Wireless Diagnostics window, tap the Signal Strength icon > Wireless Diagnostics. Figure 7-41 Wireless Diagnostics Window The Wireless Diagnostics window contains the following options. Tap the option to display the option window. • ICMP Ping - tests the wireless network connection.
Wireless Applications 7 - 31 Figure 7-42 ICMP Ping Window To perform an ICMP ping: 1. In the IP field, enter an IP address or select an IP address from the drop-down list. 2. From the Size drop-down list, select a size value. 3. Tap Start Test. The ICMP Ping test starts. Information of the ping test displays in the appropriate fields. Trace Route Window Trace Route traces a packet from a computer to a host, showing how many hops the packet requires to reach the host and how long each hop takes.
7 - 32 MC70 Integrator Guide Known APs Window The Known APs window displays the APs in range using the same ESSID as the EDA. This window is only available in Infrastructure mode. To open the Known APs window, tap Known APs in the Wireless Diagnostics window. Figure 7-44 Known APs Window See Table 7-22 for the definitions of the icons next to the AP. Table 7-22 Current Profile Window Icon Description The AP is the associated access point, and is set to mandatory.
Wireless Applications 7 - 33 Options Use the wireless Option dialog box to select one of the following operation options from the drop-down list: • Operating Mode Filtering • Regulatory • Band Selection • System Options • Change Password • Export. Operating Mode Filtering The Operating Mode Filtering options cause the Find WLANs application to filter the available networks found. Figure 7-45 OP Mode Filtering Dialog Box The AP Networks and Ad-Hoc Networks check boxes are selected by default.
7 - 34 MC70 Integrator Guide Figure 7-46 Regulatory Options Dialog Box Table 7-24 Regulatory Options Field Settings Enable 802.11d Description Select the country from the drop-down list. To connect to a profile, the profile country must match this setting, or the AP country setting if you selected the Enable 802.11d check box. The WLAN adapter attempts to retrieve the country from APs.
Wireless Applications 7 - 35 Figure 7-48 System Options Dialog Box Table 7-26 System Options Field Description Profile Roaming Configures the EDA to roam to the next available WLAN profile when it moves out of range of the current WLAN profile. Enable IP Mgmt Enables the Wireless Companion Services to handle IP address management. The Wireless Companion Service configures the IP based on what is configured in the network profile.
7 - 36 MC70 Integrator Guide Export Use Export to export all profiles to a registry file, and to export the options to a registry file. Figure 7-50 Options - Export Dialog Box To export options: 1. Tap Export Options. The Save As dialog box displays. Figure 7-51 Export Options Save As Dialog Box 2. Enter a filename in the Name: field. The default filename is WCS_OPTIONS.REG. 3. Tap Save. To export all profiles: 1. Tap Export All Profiles. The Save As dialog box displays.
Wireless Applications 7 - 37 2. Enter a filename in the Name: field. The default filename is WCS_PROFILES.REG. 3. In the Folder: drop-down list, select the desired folder. 4. Tap Save. Selecting Export All Profiles saves the current profile. This information is used to determine which profile to connect with after a warm boot or cold boot. Cold Boot Persistence Export options and profiles to provide cold boot persistence.
7 - 38 MC70 Integrator Guide User Already Logged In If already logged into the EDA, the user can launch the login dialog box for the following reasons: • Connect to and re-enable a cancelled profile. To do this: • Launch the Log On/Off dialog. • Select the cancelled profile from the profile list. • Login to the profile. NOTE Re-enable cancelled profiles using the Profile Editor Wizard and choosing to connect to the cancelled profile. Cancelled profiles are also re-enabled when a new user logs on.
Wireless Applications 7 - 39 Tapping OK sends the credentials though WCS API. If there are no credentials entered, a dialog box displays informing the user which field was not entered. The Log Off button only displays when a user is already logged on. When the Log Off button is tapped, the user is prompted with three options: Log Off, Switch Users, and Cancel. Switching users logs off the current user and re-initialize the login dialog box to be displayed for when there is no user logged on.
7 - 40 MC70 Integrator Guide
Chapter 8 Maintenance and Troubleshooting Chapter 8 Chapter 8 Maintenance and Troubleshooting Introduction This chapter includes instructions on cleaning and storing the EDA, and provides troubleshooting solutions for potential problems during EDA operation. Maintaining the EDA For trouble-free service, observe the following tips when using the EDA: • Do not scratch the screen of the EDA.
8-2 MC70 Integrator Guide Troubleshooting EDA Table 8-1 Troubleshooting the EDA Problem EDA does not turn on. Cause Solution Lithium-ion battery not charged. Charge or replace the lithium-ion battery in the EDA. Lithium-ion battery not installed properly. Ensure battery is installed properly. See Installing and Removing the Main Battery on page 1-3. System crash. Perform a warm boot. If the EDA still does not turn on, perform a cold boot. See Resetting the EDA on page 1-7. Battery failed.
Maintenance and Troubleshooting 8-3 Table 8-1 Troubleshooting the EDA (Continued) Problem EDA shuts off. Tapping the window buttons or icons does not activate the corresponding feature. A message appears stating that the EDA memory is full. EDA keeps powering down to protect memory contents. Cause Solution EDA is inactive. The EDA turns off after a period of inactivity. If the EDA is running on battery power, set this period from 1 to 5 minutes, in one-minute intervals.
8-4 MC70 Integrator Guide Table 8-1 Troubleshooting the EDA (Continued) Problem Cause The EDA does not accept scan input. Solution Scanning application is not loaded. Load a scanning application on the EDA. See the system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the EDA within proper scanning range. EDA is not programmed for the bar code type. Program the EDA to accept the type of bar code scanned.
Maintenance and Troubleshooting 8-5 Table 8-2 Troubleshooting Bluetooth Connection (Continued) Problem Cause Can’t make my Ericsson R520 phone discoverable. You attempted to bond with the phone, and when the phone presented a “pairing query,” you entered No. This prevents the phone from being discoverable until it is reset. Reset the phone by removing its battery. There is a delay in the Bluetooth stack re-initializing during a resume from suspend. This is normal behavior. No solution required.
8-6 MC70 Integrator Guide Single Slot USB/Serial Cradle Table 8-3 Troubleshooting the Single Slot USB/Serial Cradle Symptom LEDs do not light when EDA or spare battery is inserted. EDA battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. EDA is not seated firmly in the cradle.
Maintenance and Troubleshooting 8-7 Four Slot Ethernet Cradle Table 8-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Battery is not charging. Attempt by the EDA to ActiveSync failed. During communication, no data was transmitted, or transmitted data was incomplete. Cause Solution EDA removed from the cradle too soon. Replace the EDA in the cradle. The standard capacity battery (1900 mAh) fully charges in less than four hours.
8-8 MC70 Integrator Guide Vehicle Cradle Table 8-5 Troubleshooting the Vehicle Cradle Symptom Possible Cause Action EDA battery charging LED does not light up. Cradle is not receiving power. Ensure the power input cable is securely connected to the cradle’s power port. EDA battery is not recharging. EDA was removed from the cradle too soon. Replace the EDA in the cradle. The standard capacity battery (1900 mAh) fully charges in less than four hours.
Maintenance and Troubleshooting 8-9 Four Slot Spare Battery Charger Table 8-6 Troubleshooting the Four Slot Spare Battery Charger Symptom Battery not charging. Possible Cause Action Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. The standard capacity battery (1900 mAh) fully charges in less than four hours.
8 - 10 MC70 Integrator Guide Cables Table 8-7 Troubleshooting the Cables Symptom Possible Cause Action EDA battery is not charging. EDA was disconnected from AC power too soon. Connect the power cable correctly. Confirm main battery is charging under Start > Settings > System > Power. The standard capacity battery (1900 mAh) fully charges in less than four hours. The extended capacity battery (3800 mAh) fully charges in less than eight hours. Battery is faulty.
Maintenance and Troubleshooting 8 - 11 Table 8-8 Troubleshooting the Magnetic Stripe Reader (Continued) Symptom EDA battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action EDA was removed from MSR or MSR was unplugged from AC power too soon. Ensure MSR is receiving power. Ensure EDA is attached correctly. Confirm main battery is charging under Start > Settings > System > Power.
8 - 12 MC70 Integrator Guide Table 8-9 Troubleshooting the Trigger Handle Problem Cause Solution Trigger Handle is not properly seated in the cradle. Remove the Trigger Handle from the cradle and reinsert. Power is not available to the cradle. Ensure that power connections to the cradle are connected properly. Cannot print to printer. Printer cable not connected properly. Ensure cable is connected properly to the printer and Trigger Handle.
Technical Specifications Appendix A Appendix A Technical Specifications Technical Specifications The following table summarizes the EDA’s intended operating environment and technical hardware specifications. Table A-1 EDA Technical Specifications Item Description Physical Characteristics Dimensions 6 in. L x 3 in. W x 1.5 in H 15.3 cm L x 7.6 cm W x 3.7 cm H Weight (inc. standard battery) LAN/PAN configurations: 11.2 oz./314 g WAN/LAN/PAN configurations: 12 oz.
A-2 MC70 Integrator Guide Table A-1 EDA Technical Specifications (Continued) Item Description Performance Characteristics CPU Intel® XScale™ Bulverde PXA270 processor at 624MHz Operating System Microsoft® Windows Mobile™ 2005 Memory 64MB RAM/128MB ROM Interface/Communications RS-232, USB 1.
Technical Specifications Table A-1 EDA Technical Specifications (Continued) Item Voice Communication Description Integrated Voice-over-IP ready (P2P, PBX, PTT), Wi-Fi™-certified, IEEE 802.11a/b/g direct sequence wireless LAN Wireless PAN Data and Voice Communications Bluetooth Class II, v 1.2 Data Capture Specifications Options 2D imager, 1D linear Linear 1D Scanner (SE800HP) Specifications Optical Resolution 0.005 in.
A-4 MC70 Integrator Guide MC70 Accessory Specifications Table A-2 Single Slot USB/Serial Cradle Technical Specifications Feature Description Dimensions 4.3 in. L x 2.3 in. W x 3.2 in. H (10.92 cm L x 5.84 cm W x 8.13 cm H) Weight 6.9 oz (196 g) Power 12 V Interface USB, Serial Operating Temperature 32° to 122° F (0° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Charging Temperature 32° to 104° F (0° to 40° C) Humidity 5% to 95% non-condensing Drop 30.0 in. (76.
Technical Specifications A-5 Table A-4 Four Slot Spare Battery Charger Technical Specifications Feature Description Dimensions 8.25 in. L x 6.0 in. W x 1.7 in. H (20.96 cm L x 15.24 cm W x 4.32 cm H) Weight 13.6 oz (386 g) Power 12 V Operating Temperature 32° to 104° F (0° to 40° C) Storage Temperature -40° to 158° F (-40° to 70° C) Charging Temperature 32° to 104° F (0° to 40° C) Humidity 5% to 95% non-condensing Drop 30.0 in. (76.
A-6 MC70 Integrator Guide COM Port Definitions Table A-6 MC70 External COM Connector Definitions COM Port Definition COM1 Scanner COM2 Available COM3 IRComm COM4 Raw IrDA COM5 External Connector COM6 Available COM7 Available COM8 Available COM9 Available Pin-Outs Pin 1 Figure A-1 External Connector Table A-7 External Connector Pin-Outs Pin Description 1 Power Gnd 2 CRADLE_DETECT 3 RS232_DCD/TRIGGER 4 USB_D- 5 USB_D+ 6 USB_Gnd 7 USB_Vbus 8 USB_ID
Technical Specifications Table A-7 External Connector Pin-Outs (Continued) Pin Description 9 RS232_TXD 10 RS232_RXD 11 RS232_RTS 12 RS232_CTS 13 RS232_DTR 14 RS232_DSR 15 External_5.0V_Out 16 External DC In_5.
A-8 MC70 Integrator Guide
Software Configuration Appendix B Chapter B Appendix B Software Configuration Radio Power Status LED The MC70 has three LED indicators. The Scan/Decode LED indicates status for scanning. The Charge Status LED indicates status for main battery charging. The Radio Power Status LED indicates radio status. The Radio Power Status LED is disabled by default. To enable the LED a registry key must be changed.
B-2 MC70 Integrator Guide
Glossary A API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Aperture. The opening in an optical system defined by a lens or baffle that establishes the field of view. Application Programming Interface. See API. ANSI Terminal. A display terminal that follows commands in the ANSI standard terminal language.
Glossary - 2 MC70 Integrator Guide Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of data. The pattern of 0 and 1 values within the byte determines its meaning. Bits per Second (bps). Bits transmitted or received. BOOTP. A protocol for remote booting of diskless devices. Assigns an IP address to a machine and may specify a boot file.
Glossary - 3 Code 93. An industrial symbology compatible with Code 39 but offering a full character ASCII set and a higher coding density than Code 39. Code Length. Number of data characters in a bar code between the start and stop characters, not including those characters. Cold Boot. A cold boot restarts the mobile computer and erases all user stored records and entries. COM port. Communication port; ports are identified by number, e.g., COM1, COM2. Continuous Code.
Glossary - 4 MC70 Integrator Guide DTE. See Data Terminal Equipment. E EAN. European Article Number. This European/International version of the UPC provides its own coding format and symbology standards. Element dimensions are specified metrically. EAN is used primarily in retail. Element. Generic term for a bar or space. Encoded Area. Total linear dimension occupied by all characters of a code pattern, including start/stop characters and data. ENQ (RS-232).
Glossary - 5 IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification. Conformity is ensured through a software restriction of 120 seconds of laser operation within any 1000 second window and an automatic laser shutdown if the scanner's oscillating mirror fails. IEEE Address. See MAC Address. Input/Output Ports.
Glossary - 6 MC70 Integrator Guide K Key. A key is the specific code used by the algorithm to encrypt or decrypt the data. Also see, Encryption and Decrypting. L LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. Laser Diode.
Glossary - 7 Mobile Computer. In this text, mobile computer refers to the Symbol Series 9000 wireless portable computer. It can be set up to run as a stand-alone device, or it can be set up to communicate with a network, using wireless radio technology. N Nominal. The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive and negative deviations from this value. Nominal Size. Standard size for a bar code symbol.
Glossary - 8 MC70 Integrator Guide Percent Decode. The average probability that a single scan of a bar code would result in a successful decode. In a well-designed bar code scanning system, that probability should approach near 100%. PING. (Packet Internet Groper) An Internet utility used to determine whether a particular IP address is online. It is used to test and debug a network by sending out a packet and waiting for a response. Print Contrast Signal (PCS).
Glossary - 9 Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol. Its three main components are: 1) Light source (laser or photoelectric cell) illuminates a bar code,; 2) Photodetector - registers the difference in reflected light (more light reflected from spaces); 3) Signal conditioning circuit - transforms optical detector output into a digitized bar pattern. Scanning Mode.
Glossary - 10 MC70 Integrator Guide Symbol Length. Length of symbol measured from the beginning of the quiet zone (margin) adjacent to the start character to the end of the quiet zone (margin) adjacent to a stop character. Symbology. The structural rules and conventions for representing data within a particular bar code type (e.g. UPC/EAN, Code 39, PDF417, etc.). T TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork dissimilar systems.
Glossary - 11 ignored, because there is no time to retransmit. If UDP is used and a reliable delivery is required, packet sequence checking and error notification must be written into the applications. UPC. Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars and two spaces, each of which is any of four widths. The standard symbology for retail food packages in the United States. V Visible Laser Diode (VLD).
Glossary - 12 MC70 Integrator Guide
Index IndexIndex Numerics 802.11 ESSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 auto charge cable . . . . . . . . . . . . . . . . . . . . . . . . 1-2 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2, 2-27 communication/charge cables . . . . . . . . . . . . . 2-28 battery charging . . . . . . . . . . . . . . . . . . . . . 2-29 LED indicators . . . . . . . . . . . . . . . . . . . . .
Index - 2 MC70 Integrator Guide battery backup charging . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 charging main battery . . . . . . . . . . . . . . . . . . . . . 1-5 installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 spare charging . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 3 setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 four slot spare battery charger . . . . . . . . . . 2-1, 2-21 charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 charging indicators . . . . . . . . . . . . . . . . . . . 2-22 setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 mounting bracket . . . . . . . . . . . . . . . . . . . . . . . 2-11 single slot USB serial . . . . . . . . . . . . . . 2-1, 2-4, 2-5 charging indicators . . . . . . . .
Index - 4 MC70 Integrator Guide I image update deploying CAB files . . . . . . . . . . . . . . . . . . . . . . . 4-5 information, service . . . . . . . . . . . . . . . . . . . . . . . . . . xviii infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 installing battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 internet disconnecting GPRS . . . . . . . . . . . . . . . . . . . . . . 5-6 via GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index - 5 rapid deployment client . . . . . . . . . . . . . . . . . . . . . . 4-13 AirBEAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 RD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 AirBEAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 regmerge . . . . . . . . . . . . . . . . . . . . . .
Index - 6 MC70 Integrator Guide XML provisioning . . . . . . . . . . . . . . . . . . . . . . . 4-10 Symbol Mobility Developer Kit . . . . . . . . 2-xviii, 1-2, 4-24 T technical specifications . . . . . . . . . . . . . . . . . . . . . . . A-1 accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4 text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 TKIP (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 TRG7000 . . . . . . . . . . . . . . .
Tell Us What You Think... We’d like to know what you think about this Manual. Please take a moment to fill out this questionnaire and fax this form to: (631) 738-3318, or mail to: Motorola, Inc. One Symbol Plaza M/S B-4 Holtsville, NY 11742-1300 Attention: Technical Publications Manager IMPORTANT: If you need product support, please call the appropriate customer support number provided. Unfortunately, we cannot provide customer support at the fax number above.
Motorola, Inc. One Symbol Plaza Holtsville, New York 11742-1300 http://www.symbol.
