MC65 User Guide
MC65 User Guide 72E-133769-01 Rev.
ii MC65 User Guide © 2010 Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change -01 Rev. A Date 9/2010 Description Initial release.
iv MC65 User Guide
Table of Contents About This Guide Introduction ........................................................................................................................................... Documentation Set ......................................................................................................................... Configurations....................................................................................................................................... Software Versions.................
vi MC65 User Guide Turning Off the Radios ................................................................................................................... Handstrap Replacement ...................................................................................................................... Removal ......................................................................................................................................... Installation ....................................................
Table of Contents vii Chapter 3: Making Calls Introduction .......................................................................................................................................... Making a Call ....................................................................................................................................... Using the Phone Keypad ............................................................................................................... Smart Dialing .............
viii MC65 User Guide Viewing an Email Message ............................................................................................................ Replying to or Forwarding a Message ........................................................................................... SMS Messaging ................................................................................................................................... Sending a Text Message ..........................................................
Table of Contents ix Chapter 8: Using GPS Navigation Introduction .......................................................................................................................................... Software Installation ............................................................................................................................ MC65 GPS Setup ................................................................................................................................ Operation ....
x MC65 User Guide Play .......................................................................................................................................... Voice Tag ................................................................................................................................. Digit Trainer Settings ..................................................................................................................... Digit Setting Settings ............................................
Table of Contents Cleaning ............................................................................................................................................... Materials Required ......................................................................................................................... Cleaning the MC65 ........................................................................................................................ Housing ....................................................
xii MC65 User Guide Using Call History .......................................................................................................................... Making a Speed Dial Call ............................................................................................................... Answering a Call .................................................................................................................................. Incoming Call Features ........................................
About This Guide Introduction This guide provides information about using the MC65 Enterprise Digital Assistant (EDA) and accessories. NOTE Screens and windows pictured in this guide are samples and can differ from actual screens. This guide provides instructions for using the Enterprise Home screen and Dialer. See Appendix C, Windows Mobile Home Screen and Dialer for information on using the Microsoft Home screen and Dialer.
xiv MC65 User Guide Software Versions This guide covers various software configurations and references are made to operating system or software versions for: • Adaptation Kit Update (AKU) version • OEM version • Fusion software • Phone software. AKU Version To determine the Adaptation Kit Update (AKU) version: Tap Start > Settings > System > About > Version. The second line lists the operating system version and the build number. The last part of the build number represents the AKU number.
About This Guide xv • Chapter 7, Using Bluetooth explains Bluetooth functionality on the MC65. • Chapter 8, Using GPS Navigation provides information about GPS navigation with the MC65. • Chapter 9, Settings provides basic instructions for using the MC65 phone. • Chapter 10, Accessories describes the available accessories and how to use them with the MC65.
xvi MC65 User Guide • Latest ActiveSync software, available at: http://www.microsoft.com. For the latest version of this guide and all guides, go to: http://supportcentral.motorola.com. Service Information If you have a problem with your equipment, contact Motorola Enterprise Mobility support for your region. Contact information is available at: http://www.motorola.com/enterprisemobility/contactsupport.
Chapter 1 Getting Started Introduction This chapter lists the parts and accessories for the MC65 and explains how to set up the MC65 for the first time. Unpacking Carefully remove all protective material from the MC65 and save the shipping container for later storage and shipping. Verify that you received the following: • MC65 EDA • 3600 mAh Lithium-ion battery • stylus with tether (installed) • screen protector, installed on display window • Regulatory Guide • Quick Start Guide.
1-2 MC65 User Guide Getting Started To start using the MC65 for the first time: • Install a microSD card (optional) • Install the SIM card (GSM only) • Install the main battery pack. • Charge the MC65. • Power on the MC65. Installing a microSD Card The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
Getting Started 1-3 microSD card Holding tab Figure 1-2 Insert microSD Card in Holder 7. Close the card holder door and push down until it is securely in place. 8. If installing a SIM card, proceed to Installing the SIM Card. 9. Close the SIM card holder door and slide down until it locks into place. 10. Close the rubber access door. Installing the SIM Card NOTE GSMs only. GSM phone service requires a Subscriber Identification Module (SIM) card. Obtain the card from the your service provider.
1-4 MC65 User Guide Figure 1-3 Lifting the SIM Cover 4. Insert the SIM card, as shown in Figure 1-4 ensuring that the card slides into the holding tabs on each side of the door. Figure 1-4 Inserting the SIM Card 5. Close the SIM card holder door and slide down to lock into place. 6. Close the rubber access door. 7. Install the battery. NOTE For detailed information about WWAN activation, see First-time Network Activation on page 1-7. Installing the Battery To install the battery. 1.
Getting Started 1-5 Battery Release Latch 2 1 Battery Figure 1-5 Inserting the Battery Charging the Battery CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page 11-2. Charging the Main Battery Before using the MC65 for the first time, charge the main battery until the amber Charging/Battery Status LED remains lit (see Table 1-1 on page 1-6 for charge status indications).
1-6 MC65 User Guide 1. Connect the charging accessory to the appropriate power source. 2. Insert the MC65 into a cradle or attach to a cable. The MC65 begins charging. The Charging/Battery Status LED blinks amber while charging, then turns solid amber when fully charged. See Table 1-1 for charging indications. The 3600 mAh battery charges in less than six hours. Table 1-1 LED Charge Indicators Charging/Battery Status LED Indication Off MC65 is not charging.
Getting Started 1-7 First-time Network Activation GSM/UMTS Activation Network Activation To activate on a GSM/UMTS network: 1. If an active SIM card was installed in the MC65, the MC65 performs the activation process. 2. The Phone Network - GSM/UMTS Setup dialog box displays. 3. Tap Yes and then OK. For some carriers, the ES400 resets. 4.
1-8 MC65 User Guide Replacing the Battery CAUTION The MC65 backup battery retains data for up to 15 minutes. Replace the battery within 15 minutes to ensure that application states are maintained and that data is not lost. 1. If the MC65 is in suspend mode, press the red Power button to wake the device. 2. Press and hold the red Power button for approximately 5 seconds. 3. Release the Power button. The Data Capture LED lights red. 4. When the LED turns off, remove the handstrap. 5.
Getting Started 5. Remove the battery. 6. Lift the rubber access door. 7. Slide SIM card holder door up to unlock. 8. Lift SIM Card holder door. 9. Lift the microSD card holder door. 10. Remove microSD card from holder. 11. Close microSD card holder door. 12. Close SIM card holder door. 13. Slide SIM card holder door down to lock into place. 14. Close the rubber access door. 15. Replace the battery. 16. Replace the handstrap. 17. If a SIM card is installed, reset the MC65.
1 - 10 MC65 User Guide 15. Reset the MC65. See Resetting the MC65 on page 2-19. Battery Management Observe the following battery saving tips: • Leave the MC65 connected to AC power at all times when not in use. • Set the MC65 to turn off after a short period of non-use. • Set the backlight to turn off after a short period of non-use. • Turn off all wireless activities when not in use. Changing the Power Settings To set the MC65 to turn off after a short period of non-use: 1. Tap Status Bar > . 2.
Getting Started 1 - 11 Turning Off the Radios To turn off the radios: 1. Tap Status Bar > . 2. Tap Phone radio to toggle the phone radio on and off. 3. Tap Wi-Fi to toggle the WLAN radio on and off. 4. Tap Bluetooth to toggle the Bluetooth radio on and off. Handstrap Replacement Removal To remove a handstrap from the MC65: CAUTION Close all running applications prior to replacing the handstrap. The backup battery maintains data for up to 15 minutes.
1 - 12 MC65 User Guide 7. Pry the handstrap and pin up and out of the handstrap mount area. 1 2 3 4 Figure 1-8 Handstrap and Pin Removal 8. Repeat for the other side of the handstrap. 9. Remove pin from the handstrap. Figure 1-9 Pin Removal 10. Pull handstrap through handstrap slot. Installation To install a new handstrap: 1. Feed bottom end of handstrap into handstrap slot on the bottom of the MC65.
Getting Started 1 - 13 Figure 1-10 Feed handstrap into Handstrap Slot 2. Slide pin into bottom of handstrap. 3. Center the pin in the handstrap loop. NOTE 4. Handstrap and pin should fit securely into the handstrap mounting area. When pulling on handstrap use enough force to engage pin into place. Pull handstrap so that the pin and bottom of handstrap slide into position in the mounting area.
1 - 14 MC65 User Guide
Chapter 2 Using the MC65 Introduction This chapter explains the buttons, status icons, and controls on the MC65, and provides basic instructions for using the MC65, including resetting the MC65 and entering and capturing data.
2-2 MC65 User Guide Battery Battery Latch Speaker Camera Flash Handstrap Camera Stylus Stylus Clip Action Button Exit Window Figure 2-2 MC65 Rear View Scan/Action Button
Using the MC65 2-3 Function Buttons The MC65’s buttons perform the following functions. Scan/Action Button Volume Up/Down Button Action Button Power Button Scan/Action Button Figure 2-3 Function Buttons • Power: Press the red Power button to turn the MC65 screen on and off. The MC65 is in suspend mode when the screen is off. For more information, see Powering On the MC65 on page 1-6. Also use the Power button to reset the MC65. See Resetting the MC65 on page 2-19.
2-4 MC65 User Guide Keypads The MC65 offers two types modular keypad configurations: Numeric and alpha-numeric. Figure 2-4 MC65 Numeric Keypad Refer to Chapter B, Keypads for detailed information on the keypad configurations. Keypad Remapping The user has the ability to remap the keypad keys to characters or applications. Refer to Chapter 9, Settings for detailed information on remap keypad keys.
Using the MC65 2-5 Motorola Home Screen The customizable Motorola Home screen provides faster and easier access to features and applications, and allows users to tailor the interface to improve their unique workflow and maximize on-the-job efficiency.
2-6 MC65 User Guide Table 2-1 Status Bar Icons (Continued) Icon Description Icon Description There are more notification icons than can be displayed. Bluetooth radio is on. One or more Email messages were received. Receiving MMS message. Sending MMS message. MMS message sent successfully. MMS message received successfully. Microsoft customer feedback alert. MMS message received successfully. Connectivity Connection is active. Connection is not active. Synchronization is occurring.
Using the MC65 2-7 Table 2-1 Status Bar Icons (Continued) Icon Description Icon Description Vibrate is on. Battery Battery is charging. Battery has a full charge. Battery has a high charge. Battery has a medium charge. Battery has a low charge. Battery has a very low charge. Cards Cards provide quick access to completing common tasks. The number and type of cards available to an end user are configurable by the system administrator or the end user. By default, the MC65 ships with four cards.
2-8 MC65 User Guide Tap to Open Date and Time Carrier Name Tap to Configure Cards Tap to Configure Active Card Owner’s Name Owner’s Company Name Figure 2-8 Full Home Card Table 2-2 lists the Home card shortcut icons. Table 2-2 Home Card Icons Icon Description Calendar: Indicates the next appointment in the calendar. Tap to open the Calendar application. Outlook Email: Indicates the number of unread emails in Outlook email. Tap to open the Email application.
Using the MC65 2-9 Weather Card The Weather card display the weather for a selected city. Figure 2-9 Weather Card See Weather Card on page 9-12 for information on configuring the Weather card. Time Tracker Card The Time Tracker card provide a easy way for a worker to log hours spend at a job and output this information in a easy to use format. Figure 2-10 Time Tracker Card See Weather Card on page 9-12 for information on configuring the Weather card.
2 - 10 MC65 User Guide My Apps Window The My Apps window provides access to all the applications on the MC65. The window is configurable so that it can display favorite applications. To configure the My Apps window refer to My Apps Window Setup on page 9-9. Figure 2-12 My Apps Window My Apps screen is configurable. See My Apps Window Setup on page 9-9 for more information.
Using the MC65 2 - 11 Table 2-3 Programs Available on the Start Menu Icon Description Icon Description Getting Started - Launch the Getting Started application. Help - Access on-line Help topics. Internet Explorer - Browse Web and WAP sites as well as download new programs and files from the Internet. Internet Sharing - Connect a notebook computer to the Internet using the MC65's data connection. Marketplace - Purchase applications from the Marketplace.
2 - 12 MC65 User Guide Table 2-3 Programs Available on the Start Menu Icon Description Icon Description Tasks - Keep track of tasks. Text - Send an SMS or MMS message. Toolbox - Contains the Adobe Reader and Voice Commander applications. Wireless Companion - Opens the Wireless Companion folder. Windows Live - Use the mobile version of Windows Live™ to find information on the web. Windows Media - Play back audio and video files.
Using the MC65 2 - 13 • Status • Settings . Tap an icon to open the associated tab. Scroll left or right to view more icons. Programs The Programs tab lists the programs that are currently running on the MC65 and allows for easy program switching, and a quick way to end processes. Figure 2-15 Programs Tab • To switch to a program, tap the name of the program. • To end a running program, tap the X next to the program name. • To close all running programs, tap Close All.
2 - 14 MC65 User Guide • SD Card - Lists the total available memory and the amount of memory that is currently being used. • RAM - Lists the total available RAM and the amount of RAM that is currently being used. Tap View Large Files to display files on the MC65 that are above a specific byte size. Sound Profiles The Sound Profiles tab provides direct access to sound-related profiles. Figure 2-17 Sound Profiles Tab To select a profile, tap the profile name.
Using the MC65 2 - 15 Power & Radio The Power & Radio tab displays the current battery status and direct access to power profiles and power/radio-related options. Figure 2-18 Power & Radio Tab The Battery remaining graphic displays the amount of battery power remaining in the form of a bar graph and also as a percentage. The Profile row displays the current profile that is being used. To set a defined profile, tap Profile. A list of profiles appear. Select a profile from the list.
2 - 16 MC65 User Guide • ActiveSync - Set the interval between which the MC65 checks for email and calendar events. • ActiveSync off - Set the interval between which the MC65 checks for email and calendar events. Refer to Power Profiles on page 9-6 for information on creating new profiles. Alarms The Alarms tab controls the Windows Mobile enabled alarms. Tap Status Bar > . Figure 2-20 Alarms Tab To turn an alarm on or off tap the alarm name. To change an alarm setting, tap Edit Alarm.
Using the MC65 2 - 17 Status The Status tab displays all system notifications. Figure 2-22 Status Tab Tap a notification to read the associated information. Settings The Settings tab lists the settings applications on the MC65. Tap an item in the list to open the associated setting application or folder. Slide the list up to view more settings icons. Figure 2-23 Settings Tab Refer to Table 9-1 on page 9-1 for a list of setting application icons and their descriptions.
2 - 18 MC65 User Guide Adjusting Volume To adjust the system volume: 1. Press the volume buttons on the right side of the MC65 to increase and decrease the system volume. The Volume dialog box appears. 2. As you increase or decrease the volume, the slider moves accordingly. You can also move the slider to adjust the volume. 3. Select the Vibrate radio button to turn off the system audio and enable the MC65 to vibrate upon system notifications. 4.
Using the MC65 2 - 19 Table 2-4 LED Indications (Continued) LED State Indication Solid Red (after Power button press) MC65 is shutting down for battery replacement. Off Data capture not enabled. Charging/Battery Status LED Slow Blinking Amber Main battery in MC65 is charging. Solid Amber Main battery in MC65 is fully charged. Fast Blinking Amber Charging error. Off Not charging. WAN Radio Status LED Slow Blinking Green RF (WWAN) radio is on. Off RF (WWAN) radio is off.
2 - 20 MC65 User Guide Figure 2-25 Lock Screen Drag to either the right or left side of the screen. If a password is set up, enter the password and then tap to unlock and display the Home screen, tap to unlock and display the Contacts window, tap to unlock and display the Messaging window. Figure 2-26 Password Window Stylus Use the MC65 stylus to select items and enter information. The stylus functions as a mouse.
Using the MC65 2 - 21 Entering Data When entering data on the keypad, use either the single-hand method or the two-hand method as shown in Figure 2-27.
2 - 22 MC65 User Guide Data Capture The MC65 offers two types of data capture options: • Imaging • Digital camera. NOTE To perform data capture a scanning enabled application must be installed on the MC65. A sample scanning application can be downloaded from the Motorola Support site at http://support.symbol.com.
Using the MC65 2 - 23 Scanning Considerations Typically, scanning is a simple matter of aim, scan, and decode and a few quick trial efforts master it. However, consider the following to optimize scanning performance: • Range Any scanning device decodes well over a particular working range — minimum and maximum distances from the bar code. This range varies according to bar code density and scanning device optics.
2 - 24 MC65 User Guide Figure 2-28 Imager Scanning 4. Press and hold the scan button. The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the brackets in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions. The Scan/Decode LED lights red to indicate that scanning is in process, then lights green and a beep sounds, by default, to indicate the bar code was decoded successfully.
Using the MC65 2 - 25 6. Disable DataWedge. a. Tap Start > Settings > System > DataWedge. b. Tap the Running option to end the DataWedge process. The DataWedge Status changes to Stopped. c. Tap OK. Digital Camera Scanning To read a bar code, a scan-enabled application is required. The MC65 contains the DataWedge application that allows the user to enable the camera, decode the bar code data and display the bar code content. 1. Enable DataWedge. a. Tap Start > Settings > System > DataWedge. b.
2 - 26 MC65 User Guide Using Voice-Over-IP The MC65 supports Voice over IP over WLAN (VoWLAN) using Motorola or third party voice clients. The MC65 can communicate using VoIP either using the MC65 supports several audio outputs, including back speaker phone, front receiver or handset, and Bluetooth headset. It is recommended that the wireless network use the 802.11a (5 GHz) band for voice applications. Using the 5 GHz band avoids some noise sources that may occur on the 802.11b/g (2.
Chapter 3 Making Calls Introduction NOTE If using the Windows Mobile Dialer, refer to Windows Mobile Dialer on page C-4 for information on using the dialer. Use the MC65 to make phone calls, keep track of calls, and send text messages. Your wireless service provider may also provide other services such as voice mail, call forwarding, and caller ID.
3-2 MC65 User Guide Call Line GSM/UMTS CDMA Figure 3-1 Enterprise Dialer If the user taps a wrong number, tap the Delete key to erase each subsequent digit. To erase the entire number, tap and hold the Delete key. NOTE 2. Enter the phone number on the dialer or keypad. The number appears in the Call Line. 3. Tap the green Call Line or press 4. Tap Cancel to cancel the call or tap Speaker to place the MC65 in speakerphone mode. 5.
Making Calls 3-3 Smart Dialing starts looking for numbers or contacts that match the sequence entered. To find a phone number: • Enter the first one or two digits to find a phone number in Call History. • Enter the first three digits or more to find a phone number from the saved Contacts and SIM card. To find a contact name: • Enter the first letter of a contact’s first name or last name.
3-4 MC65 User Guide Tap Call Work, Call Home or Call Mobile. 4. Using Call Log To make a call using Call Log: 1. Press . 2. From the Phone shortcut, tap 3. Tap the contact or phone number. 4. Tap SEND or press 5. Tap Cancel or press . . ok to stop dialing or end the call. Answering a Call When the MC65 receives an incoming call a dialog box appears. If the phone is set to ring, a ring tone sounds. Answer or ignore the incoming call. To answer an incoming call tap Answer or press .
Making Calls 3-5 Emergency Calling The service provider programs one or more emergency phone numbers, such as 911 or 999, that the user can call under any circumstances, even when the phone is locked, a SIM card is not inserted or the phone is not activated. Your service provider can program additional emergency numbers into the SIM card. However, the SIM card must be inserted in the MC65 in order to use the numbers stored on it. See the service provider for additional information.
3-6 MC65 User Guide Using Call Log Use Call Log to call someone who was recently called, or recently called in. The Call Log provides the time of all incoming, outgoing, and missed calls. Table 4-1 lists the call Log icons that appear in the Call Log window. Press and then tap to open the Call Log window. Figure 3-3 Call Log Window Table 3-2 Call Log Icons Icon Description This icon appears next to the contact information for all outgoing calls.
Making Calls 3-7 Figure 3-4 Call Log Window 2. Tap an item to call the number or tap to open the Options window for that item. 3. Select an applicable option from the menu. 4. Depending on the option selected, the appropriate window displays. For example, select SMS to display the Text Messages window. 5. Tap to close the Options window. Conference Calling For use on GSM/UMTS networks. NOTE Conference Calling and the number of conference calls allowed may not be available on all services.
3-8 MC65 User Guide Figure 3-5 Two Calls 7. Tap the Call Line 1 to make that call active. The second call go on hold. 8. Tap to create a conference call (three callers). Figure 3-6 Two Merged Calls 9. To add a third caller tap conference is on hold. Figure 3-7 Adding a Third Call . The dialer appears.
Making Calls 10. To add the new caller to the conference tap 3-9 . Figure 3-8 Three Merged Calls 11. Tap to view all callers. Figure 3-9 Un-Merge Calls 12. Tap to remove a caller from the conference. 13. To end the conference call, tap next to the Call Line. Calls Complete dialog appears and then the dialer displays. . NOTE To speak privately with one party during a conference call, tap To include all parties again, tap. and then tap next to the caller.
3 - 10 MC65 User Guide Making a 3-Way Call NOTE For use on CDMA networks. 3-way Calling may not be available on all services. Please check with the service provider for availability. With 3-Way Calling, you can talk to two people at the same time. When using this feature, the normal airtime rates will be charged for each of the two calls. 1. Enter a number and press . 2. Once you have established the connection, enter or select a number and tap Flash. 3.
Making Calls 3 - 11 Call To call a person by name: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “Call Michael Archer.” System responds with “Call Michael Archer work, is it correct?” 3. Say “Yes.” MC65 responds with “Dialing.” To call a person at a location: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “Call Mary Smith at home.” The MC65 responds with “Call Mary Smith home, is it correct?” 3. Say “Yes.” The MC65 responds with “Dialing.
3 - 12 MC65 User Guide 2. Say “Find John Smith at work.” The MC65 responds with “More than one John Smith, please select.” Voice Commander displays a window with the two contacts. (System will show both Halley Johnson and Haley Johnson for user to select.) If a contact is not found: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “Find Michael Archer at home.” 3. MC65 responds with “Michael Archer has no home number.” Redial To re-dial a previous number: 1.
Making Calls 3 - 13 What time is it To find out the time of day: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “What time is it?” The MC65 responds with “The time is 3 p.m.” Call History To view the call history window: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “Call History.”The MC65 responds with “Call history.” 3. The Call history page displays. Voice Play Music To play a specific music file: 1. Initiate Voice Commander.
3 - 14 MC65 User Guide What can I say To view the help information: 1. Initiate Voice Commander. The MC65 responds with “Say command.” 2. Say “What can I say.” The help file displays. Alternately tap Menu > Help to open the help file. Goodbye To exit the Voice Commander application, Say “Goodbye.” The MC65 responds with “Goodbye” and the application terminates. Voice Commander can be also terminated manually by tapping Menu > Exit.
Chapter 4 Using WLAN Introduction WLANs allow the MC65 to communicate wirelessly inside a building. Before using the MC65 on a WLAN, the facility must be set up with the required hardware to run the WLAN (sometimes known as infrastructure). The infrastructure and the MC65 must both be properly configured to enable this communication. Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches, Radius servers, etc.
4-2 MC65 User Guide Refer to the Wireless Fusion Enterprise Mobility Suite User Guide for Version 3.20 for detailed information on using and configuring Fusion. To access the on-device Fusion Help tap Status Bar > > Help. Wireless Zero Config Overview WZC is a Microsoft wireless connection management utility that dynamically selects a wireless network to connect to based on a user's preferences and various default settings. Switching Between Fusion and WZC To switch from Fusion to WZC: 1.
Using WLAN 4-3 Supported Applications The Fusion menu items and their corresponding applications are summarized in Table 4-1. Table 4-1 Supported Applications Application Description Fusion Support WZC Support Find WLANs Invokes the Find WLANs application which Yes displays a list of the WLANs active in your area. No Manage Profiles Invokes the Manage Profiles application (which includes the Profile Editor Wizard) to manage and edit your list of WLAN profiles.
4-4 MC65 User Guide 2. Tap and hold in the window and select Add from the pop-up menu. The Wireless LAN Profile Entry window appears. 3. In the Profile Name text box enter a name for the profile. 4. In the ESSID text box enter the ESSID. Figure 4-2 Profile ID Dialog Box 5. Tap Next. The Operating Mode dialog box displays. 6. In the Operating Mode drop-down list, select Infrastructure or Ad-hoc. Figure 4-3 Operating Mode Dialog Box 7. Tap Next. The Security Mode dialog box displays. 8.
Using WLAN 4-5 Figure 4-5 Encryption Dialog Box 12. Select the Pass-phrase or Hexadecimal Keys radio button to indicate whether a pass-phrase or hexadecimal keys will be entered on the next page. 13. Select the For added security - Mask characters entered check box to hide characters entered. Deselect this to show characters entered. 14. Tap Next. Figure 4-6 WEP-40 WEP Keys Dialog Box 15. In the Edit Key drop-down list, select the key to enter. 16. In the Key field, enter 10 hexadecimal characters. 17.
4-6 MC65 User Guide 23. In the Battery Usage Mode dialog box select a power consumption option. Figure 4-8 Battery Usage Dialog Box 24. Tap Save. Wireless Zero Config Setup To setup WLAN using WZC: NOTE Obtain the proper WLAN configuration information from your system administrator prior to performing the WZC setup procedures. The following setup procedure example shows setup of a WLAN using WEP encryption. 1. Tap Status Bar > > Wireless Zero Config. Figure 4-9 Wireless Zero Config Window 2.
Using WLAN Figure 4-10 Configure Wireless Network Window 4. In the Connects to drop-own list, select either The Internet or Work. 5. Check the This is a hidden network checkbox if the network is a hidden network. 6. Tap Next. Figure 4-11 Configure Network Authentication Window 7. In the Authentication drop-down list, select the authentication type. 8. In the Data Encryption drop-down list, select the data encryption type. 9.
4-8 MC65 User Guide Figure 4-12 Configure Network Authentication Window 11. If required, select Use IEEE 802.1x network access control check box. 12. In the EAP type drop-down list box, select the EAP type. 13. Tap Finish. More Information on WZC For more information on Microsoft Wireless Zero Config, see the Microsoft Software Developer Network (MSDN) at http://msdn.microsoft.com.
Chapter 5 Messaging Introduction This chapter describes how to use Email, SMS Messaging and MMS Messaging. Email Use email to send messages to other users. Creating an Email Message To create an email message: 1. Press Start > E-mail. 2. Select an email account. 3. Tap 4. To add recipients, enter their email addresses, separating them with a semicolon ( ; ). Tap To to add email addresses stored in Contacts. 5. Enter a subject and compose the message. 6.
5-2 MC65 User Guide 2. Tap an email to open it. Replying to or Forwarding a Message 1. On the Home screen, tap for an Outlook email or 2. Tap an email to open it. 3. Tap 4. Enter your reply message, and then tap for a personal email account. . . SMS Messaging Text messages allow the user to send and receive short text messages (SMS) to and from other mobile devices. The text can contain words, numbers, or an alphanumeric combination no longer than 160 characters.
Messaging 5-3 If the MC65 phone feature is on, the text message is sent. If it’s off, a prompt displays to turn on the phone feature. The message is saved in the Drafts folder and sent when the MC65 phone feature is turned on. When outside of coverage area, the message is saved in the Drafts folder and sent when back in a coverage area. Viewing Text Messages When an incoming text message arrives, the text notification icon appears in the Status Bar and the dialog box displays.
5-4 MC65 User Guide Figure 5-4 Text Message - Conversation Replying to an SMS Message To reply to a text message: 1. Tap Start > Text. 2. In the message list, tap a text message. The window displays previous text conversations. 3. Enter text in the reply field. 4. Tap . MMS Messaging MMS Messaging allows the user to send a pictures, videos, audio files and other file types to another mobile computer. Creating and Sending MMS Messages To send an MMS message: 1. Tap Start > Text. 2.
Messaging 5-5 Figure 5-5 MMS Window 3. To add a contact, tap Done. . A window appears with a list of contacts. Select one or more contacts and then tap 4. Tap 5. Tap in the text window to enter a text message. A window appears allowing you to add a text message plus emoticons, favorite web addresses, pre-defined text, contact information and calendar information. Tap Done after adding information. 6. Tap to attach a picture or video stored on the MC65 to the message. 7.
5-6 MC65 User Guide 4. Tap Menu > Set as Ringtone to associate a audio file as a ringtone. Replying to an MMS Message To reply to an MMS message 1. Tap Start > Text. 2. Tap the MMS message. 3. In the threaded message, tap the MMS message to open and view an MMS message. 4. After viewing the MMS message, tap Menu > Reply > via MMS to reply with an MMS message or tap Menu > Reply > via SMS to reply with a text message.
Chapter 6 Using the Camera Introduction Use Pictures & Videos to take pictures and record videos and to view them on the MC65. Taking Pictures To take a picture: 1. Tap Start > Pictures & Videos. 2. Tap Camera. Figure 6-1 Camera Window The Camera window displays the view finder. Information about the current settings or the remaining number of pictures that can be saved to the MC65 are displayed on the lower right corner of the screen. 3. Check the image on the view finder, adjust if necessary. 4.
6-2 MC65 User Guide Burst Mode Burst mode is a way to take a series of quick pictures. 1. Tap Start > Pictures & Videos. 2. Tap Camera. 3. Tap Menu > Mode > Burst. 4. Check the image on the view finder, adjust if necessary. 5. Press the Enter key to take the picture. To stop a burst of pictures before all pictures have been taken tap OK. Timer Mode To take pictures using the timer: 1. Tap Start > Pictures & Videos. 2. Tap Camera. 3. Tap Menu > Mode > Timer.
Using the Camera 6-3 Camera Configuration To configure the camera settings: 1. Tap Start > Pictures & Videos. 2. Tap Menu, then configure the device settings. • Video - Tap to switch to video mode. • Mode - Select from the following modes to take the picture: Normal - Takes picture using the default settings. Burst - Takes picture consecutively in continuous mode. • Timer - Takes picture five seconds after pressing the Enter key. • • • Brightness - Set the camera brightness level.
6-4 MC65 User Guide NOTE By default, the time limit for recording videos is set to 30 seconds. 4. Press the Enter key to begin recording. 5. Press the Enter key to stop recording. Video Configuration To configure the video settings: 1. Launch the Video application. 2. Tap Menu, then configure the device settings. • Still - Tap to switch to still (camera) mode. • Brightness - Set the video brightness level.
Using the Camera 6-5 Customizing Pictures & Videos Using the Options command you can set preference settings on how to use Pictures & Videos. To customize Pictures & Videos: 1. On either thumbnail or full screen mode, tap Menu > Options. 2. On the General tab, set the following options: • Select the size of the pictures you want to send through e-mail. Only pictures sent through an e-mail message is resized, the original picture remains unchanged. • Resize pictures for faster e-mail transfer.
6-6 MC65 User Guide
Chapter 7 Using Bluetooth Introduction Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 meters (32.8 feet)) communication and low power consumption. MC65s with Bluetooth capabilities can exchange information (e.g.
7-2 MC65 User Guide Security The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis.
Using Bluetooth 7-3 Bluetooth Configuration The following services are supported: • OBEX Object Push Services • Hands-Free Audio Gateway Services • Serial Port Services • Personal Area Networking Services • PBAP Services • Dial-Up Networking Services • HID Client Services • A2DP/AVRCP Services • File Transfer profile • General Audio/Video Distribution Profile • SIM Access Profile • Headset Profile • Generic Object Exchange Profile • Service Discovery Access profile • Generic Access Profile.
7-4 MC65 User Guide Turning Bluetooth On and Off Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the MC65. Turn on the Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity. NOTE To achieve the best battery life turn off radios not in use. Enabling Bluetooth To enable Bluetooth: 1.
Using Bluetooth 2. Ensure that the Bluetooth device to discover is in discoverable and connectable modes. 3. Ensure that the two devices are within 32.8 feet (10 meters) of one another. 4. Tap Status Bar > > Bluetooth > Devices. Figure 7-2 Bluetooth - Devices Tab 5. Tap Add new device. The MC65 begins searching for discoverable Bluetooth devices in the area. 6. Select a device from the list. Figure 7-3 Select a Bluetooth Device 7. Tap Next. The Enter Passcode window appears.
7-6 MC65 User Guide Figure 7-4 Enter Passcode 8. Enter the Passcode on the other device. The device is added to the Bluetooth list. Figure 7-5 Bluetooth Connection Confirmation The user is prompted to enter a passcode. If the device has a specific passcode, enter it in the Passcode field and tap Next. If the device does not have a specific passcode, enter a passcode in the Passcode field and tap Next. The Bluetooth radio tries to connect with the device. 9.
Using Bluetooth 7-7 Available Services NOTE Some devices might not require a PIN. This depends upon the device’s authentication. The MC65 with Microsoft Bluetooth stack offers the following services: • OBEX Object Push Services via Beam • Hands-Free Audio Gateway Services • Serial Port Services • Personal Area Networking Services • PBAP Services • Dial-up Networking • HID Client • A2DP/AVRCP. See the following sections for information on these services.
7-8 MC65 User Guide 6. Select Beam File. The MC65 searches for Bluetooth devices in the area. 7. Tap Tap to send next to the Bluetooth device to send the file to. The MC65 communicates with the device and sends the file. When completed, Tap to send changes to Done. To transfer a contact between the MC65 and another Bluetooth enabled device: 1. Ensure that Bluetooth is enabled and discoverable on both devices. 2. Ensure that the two devices are within 32.8 feet (10 meters) of one another. 3.
Using Bluetooth 7-9 Hands-free Services To connect to a Bluetooth headset: NOTE Newer Bluetooth headsets are device dependant and remember the last device they connected to. If problems occur while connecting to the headset, place the headset in discovery mode. Refer to the headset user manual for more information. Only WAN audio and Voice Commander audio is routed to the headset. System audio is still emitted through the MC65 speaker. You can accept calls and re-dial using the Hands-free profile.
7 - 10 MC65 User Guide 13. Select the serial device in the list and then tap Next. 14. Select a COM port from the drop-down list. 15. Tap Finish. NOTE No connection is made at this point. An application must open the selected COM port to trigger Microsoft Bluetooth stack to open the connection. ActiveSync Using Bluetooth Use the wireless Bluetooth serial port connection for ActiveSync similar to a physical USB cable connection.
Using Bluetooth 7 - 11 7. Select the Incoming (device initiates the connection) option, then click OK. Note the number of the COM port that was added. 8. Click OK. 9. Click Start > All Programs > Microsoft ActiveSync. 10. Click File > Connection Settings. Figure 7-8 ActiveSync Connection Settings 11. On the Allow connections to one of the following drop-down list, select the COM port with the number you noted earlier. 12. On the MC65, tap Start > ActiveSync. 13. Tap Menu > Connect via Bluetooth.
7 - 12 MC65 User Guide 6. Tap Next. The Enter Passcode window appears. 7. Enter the Passcode and the tap Next. The device is added to the Bluetooth list. 8. A dialog box appears requesting to transfer contacts to the car kit. 9. Select Yes or No. 10. If Yes is selected, contacts from the MC65 are transferred to the car kit. Dial-Up Networking Services Dial-up networking allows the user to connect a PC or laptop to the MC65 and use the MC65 as a modem to connect to an office network or ISP.
Using Bluetooth 7 - 13 4. Tap Start > Settings > Bluetooth > Devices. 5. Tap Add new device. The MC65 begins searching for discoverable Bluetooth devices in the area. 6. Select a stereo headset from the list. 7. Tap Next. The Enter Passcode window appears. Refer to the device’s User Manuals for more information. 8. Tap Connect. The MC65 connects to the stereo headset. For stereo headsets that can use hands-free services, connect to the hands-free service after connecting to the A2DP service: 1.
7 - 14 MC65 User Guide
Chapter 8 Using GPS Navigation Introduction The MC65 includes Global Positioning System (GPS) technology. GPS technology is based on a worldwide system of GPS satellites orbiting the earth that continuously transmit digital radio signals. These radio signals contain data on the satellites’ locations and their exact clock time and are used to determine your location on the earth.
8-2 MC65 User Guide Operation Acquiring satellite signals may take several seconds to a few minutes. It is best to be outside and have a clear, unobstructed view of the sky. Without a clear view, acquisition takes much longer and could result in the MC65 being unable to compute the initial position quickly. When operating the device indoors access to the GPS signals may be limited or unavailable. NOTE When using a GPS navigation application, ensure that the MC65 does not go into suspend mode.
Using GPS Navigation 8-3 Figure 8-1 GPS Assistance Window To set the source of the data tap Source and select one of the options: WAN (default), WLAN, Active Sync, Any, None. To set the frequency of updating the data tap Update Frequency and select one of the options: On Demand (default), 1 Day, 2 Days, 4 Days, 7 Days. To manually update the data tap the Update Now button.
8-4 MC65 User Guide
Chapter 9 Settings Introduction This chapter provides information for customizing the MC65. Settings Folder Table 9-1 lists setting applications pre-installed on the MC65. Tap Status Bar > the Settings tab. or tap Start > Settings to open Table 9-1 Setting Applications Icon Name Description Icon Name Description Bluetooth Turn on Bluetooth, set the MC65 to visible mode and scan for other Bluetooth devices in the area. Lock Set a password for the MC65.
9-2 MC65 User Guide Table 9-1 Setting Applications (Continued) Icon Name Personal Folder Description Icon Name Description Contains personal setting applications. Microsoft My Phone Synchronizes the phone’s contacts, calendar, tasks, text messages, music, photos, videos and other documents with your My Phone account at www.microsoft.com. Beam Set the MC65 to receive incoming IrDA beams. Domain Enroll Make your device an AD domain member for device management and security.
Settings 9-3 Table 9-1 Setting Applications (Continued) Icon Name Description Icon Name Description Backlight & Keylight Set backlight and keylight settings. Refer to Backlight and Keylight Settings on page 9-7. Certificates See information about certificates installed on the MC65. Customer Feedback Submit feedback on the Windows Mobile 6 software. Encryption Allow files on a storage card to be encrypted. Encrypted files are readable only on your device.
9-4 MC65 User Guide Locking the MC65 Use the Password window to set a password to disable unauthorized access to the MC65. NOTE If the device is configured to connect to a network, use a strong (difficult to figure out) password to help protect network security. Password cracking tools continue to improve and the computers used to crack passwords are more powerful than ever. 1. Tap the Start > Settings > Lock > Password. 2. Select Prompt if device unused for check box to enable password protection.
Settings 9-5 Device Management The Device Management window provides quick and easy access to common settings and related options. The Device Management Window is accessed by tapping anywhere on the Status Bar. Sound Profiles To create a new sound profile or to edit a custom profile: 1. Tap Status Bar > 2. Tap . next to a custom profile or tap Create New to create a new profile. Figure 9-1 Sound Window 3. Edit or enter a new name for the profile in the text box. 4.
9-6 MC65 User Guide Power Profiles To edit a power profile: 1. Tap Status Bar > . 2. Tap next to the current profile. 3. Tap next to a profile to edit or tap Create New to create a new profile. Figure 9-2 Edit Profile Window 4. Edit or enter a new name for the profile in the text box. 5. For each radio, tap the name to toggle the value to On or Off. • Phone radio • Wi-Fi • Bluetooth. 6. Scroll down to view more options. 7.
Settings 9-7 Alarms To use the MC65 as a clock: 1. Tap the Status Bar > > Edit Alarm. 2. Tap one of the three alarm rows. 3. Use the time field up and down arrows to set the time. 4. Highlight the Description field, then enter a name for the alarm. 5. Tap the letter(s) representing the day(s) of the week to enable the alarm. 6. From the drop-down list, select the sound that plays when the alarm starts. Tap Play to listen to the alarm sounds and tap Stop to cancel playback. 7.
9-8 MC65 User Guide • Backlight Brightness - Select between automatic and manual control. Select Auto to automatically control the backlight. Select Manual set the backlight brightness. Select one of five levels of brightness. • Keylight - Select On Any Input to turn on the keylight upon an action or touch of the keypad. Select Always On to keep the keylight on all the time. Select Follow Display to set the Keylight to follow the same settings as the backlight.
Settings 1. Tap My Apps > Edit > Dock. 2. Tap a shortcut button to remove the assigned shortcut. 3. Tap a new program icon and then tap Save. My Apps Window Setup To create a customized application list: 1. Tap My Apps > Edit > View > Create New. 2. In the text box, enter a name for the list. 3. Scroll through the list and tap an icon to add to the new list. Each icon highlights indicating it is selected. As icons are added to the list, the icon counter increments. Figure 9-5 Add Programs 4.
9 - 10 MC65 User Guide Card Setup The cards on the Motorola Home screen can be configured and re-ordered: On any card, tap . The card flips over. Figure 9-6 Back of Card Re-Order Cards Each icon on the card back represents a card. To re-order the cards, press and hold on an icon and then drag it to a new location. Tap to return to the front of the card. Configure Cards Cards can be removed so that they do not appear on the Home screen. On any card, tap Tap to flip the card over.
Settings 9 - 11 2. Tap to view a description of the card. 3. Tap OK to return to the Home screen. Time Tracker Card The Time Tracker card is an application that keep track of time spent on projects. Project data is stored in the /Windows directory in file TimeTracker_data_file.csv. Figure 9-8 Time Tracker Main Screen 1. To create a new project, tap the Settings icons. Figure 9-9 New Project 2. In the text box, enter the project name. 3. Tap + to add the project to the list. 4. Tap Save. 5.
9 - 12 MC65 User Guide Resets the project timer Return to the main screen Displays the project name and date Displays the last session total or running time since the project was started Displays the total time for the entire project Displays the total time for the current day Starts and ends the timer Create a notification that sounds from the start of the project Figure 9-10 Project Screen 6. Tap the Start button to start the project timer. 7.
Settings 9 - 13 Change Location To change the location: 1. Tap the Settings icon. 2. Select a location from the list. Delete a Location To delete a location: 1. Tap the Settings icon. 2. Scroll to the desired location. 3. Tap the X. The location is removed from the list. 4. Tap Back to return to the Weather card front. Email Setup The MC65’s Messaging application lets users access and manage multiple email accounts simultaneously in one convenient location.
9 - 14 MC65 User Guide NOTE 7. For some common email types, the MC65 automatically detects and configures the email settings without performing this step. Tap the Try to get e-mail settings automatically from the Internet checkbox to place a checkmark in the checkbox. Tap Next to attempt to retrieve these settings automatically. This process may take several minutes. The MC65 attempts to determine the necessary communication settings for both incoming and outgoing email messages. 8.
Settings 9 - 15 5. The Save password checkbox is checked by default to allow the MC65 to always remember the email account password. To prevent other users from viewing your email, tap the Save password checkbox to remove the checkmark and deactivate the feature. 6. Tap Next. 7. Tap the Try to get e-mail settings automatically from the Internet box to remove the checkmark from the box and tap Next. 8. In the Your e-mail provider: drop-down list, select Internet e-mail and tap Next. 9.
9 - 16 MC65 User Guide Editing an Email Account To edit general email settings: 1. Start > E-mail. 2. Highlight an account and tap Menu > Options. 3. Tap the desired email account from the on screen list. 4. Tap Edit Account Setup. 5. Confirm the email address and make any changes if necessary. Tap Next. 6. Confirm the Your name and Account display name information and make any changes if necessary. Tap Next. 7.
Settings 9 - 17 • In the Message download limit drop-down list, select the size limit of files attached to email messages. 18. Tap Finish. Setting Email Signatures Signatures are the string of text automatically added to the end of an outgoing emails or messages. 1. Start > E-mail. 2. Tap Menu > Options. 3. Highlight an account and tap Signatures. 4. In the Select an account drop-down list, select a pre-existing account. 5.
9 - 18 MC65 User Guide Voice Commander Use the Voice Commander Settings to configure the Voice Commander application. There are five major functions: • Contacts • Applications • Music • Digit Trainer • Advanced Settings. To configure Voice Commander setting tap Start > Settings > Personal > Voice Commander Settings. Contacts Settings The Contacts tab lists all the names in the MC65 Contacts and SIM card (if installed).
Settings 9 - 19 Application Settings The Application tab lists all the applications installed in the Start menu. When a new application installed, Voice Commander automatically updates the recognition database. A check in a box indicates that the application can be recognized normally. An unchecked box indicates that the application is not in the recognition range. A grayed box indicates that the application name contains some unrecognizable characters, such as symbols or marks.
9 - 20 MC65 User Guide 2. Tap . 3. After the beep, say the music file name. For example: Drive. 4. After the second beep, repeat it. 5. Voice Commander builds the recorded voice tag. 6. Voice Commander plays back the recorded voice tag to confirm the voice tag has been created successfully, and appears to the right of the music file name. NOTE Tap again rebuild the voice tag. Tap to delete the voice tag.
Chapter 10 Accessories Introduction MC65 accessories, listed below, provide a variety of product support capabilities. Accessories Table 10-1 lists the accessories available for the MC65 EDA. Table 10-1 MC65 Accessories Accessory Part Number Description Cradles Single Slot USB Cradle CRD5500-1000UR Charges the MC65 main battery and a spare battery. Synchronizes the MC65 with a host computer through a USB connection.
10 - 2 MC65 User Guide Table 10-1 MC65 Accessories (Continued) Accessory Auto Charge Cable Part Number Description VCA5500-01R Charges the MC65 using a vehicle’s cigarette lighter. Spare 3600 mAh lithium-ion battery BTRY-MC55EAB02 Replacement 3600 mAh battery. DEX Cable 25-127558-01R For use with electronic data exchange For example, vending machines. Trigger Handle TRG5500-100R Adds a gun-style handle with a scanning trigger for comfortable and productive data capture.
Accessories 10 - 3 Single Slot USB Cradle This section describes how to use a Single Slot USB cradle with the MC65. For USB communication setup procedures refer to the MC65 Integrator Guide. The Single Slot USB Cradle: • Provides 5.4 VDC power for operating the MC65. • Synchronizes information between the MC65 and a host computer. Refer to the MC65 Integrator Guide for information on setting up a partnership between the MC65 and a host computer. • Charges the MC65’s battery. • Charges a spare battery.
10 - 4 MC65 User Guide Charging the Spare Battery Spare Battery Spare Battery Charging LED Figure 10-2 Spare Battery Charging Battery Charging Indicators The Single Slot USB Cradle charges the MC65’s main battery and a spare battery simultaneously. The MC65’s charge LED indicates the status of the battery charging in the MC65. See Table 1-1 on page 1-6 for charging status indications. The spare battery charging LED on the cradle indicates the status of the spare battery charging in the cradle.
Accessories 10 - 5 Table 10-2 Spare Battery LED Charging Indicators (Continued) Spare Battery LED (on cradle) Indication Slow Blinking Amber Spare battery is charging. Solid Amber Charging complete. Fast Blinking Amber Charging error.
10 - 6 MC65 User Guide Four Slot Charge Only Cradle This section describes how to set up and use a Four Slot Charge Only cradle with the MC65. The Four Slot Charge Only cradle: • Provides 5.4 VDC power for operating the MC65. • Simultaneously charges up to four MC65 devices. Charging Insert the MC65 into a slot to begin charging. Figure 10-3 MC65 Battery Charging Battery Charging Indicators The MC65’s charge LED shows the status of the battery charging in the MC65.
Accessories 10 - 7 Four Slot Ethernet Cradle This section describes how to set up and use a Four Slot Ethernet cradle with the MC65. For cradle communication setup procedures refer to the MC65 Integrator Guide. The Four Slot Ethernet cradle: • Provides 5.4 VDC power for operating the MC65. • Connects the MC65 (up to four) to an Ethernet network. • Simultaneously charges up to four MC65 devices. Charging Insert the MC65 into a slot to begin charging.
10 - 8 MC65 User Guide VCD5000 Vehicle Cradle This section describes how to use a VCD5000 vehicle cradle with the MC65. For cradle installation and communication setup procedures refer to the MC65 Integrator Guide. Once installed in a vehicle, the cradle: • holds the MC65 securely in place • provides power for operating the MC65 • re-charges the battery in the MC65. Charging the MC65 Battery Insert the MC65 into the vehicle cradle to begin charging.
Accessories 10 - 9 Release Lever Figure 10-6 Removing the MC65 Battery Charging Indicators The MC65’s charge LED indicates the status of the battery charging in the MC65. See Table 1-1 on page 1-6 for charging status indications. The 3600 mAh battery fully charges in less than six hours. Charging Temperature Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). Charging is intelligently controlled by the MC65.
10 - 10 MC65 User Guide Four Slot Battery Charger This section describes how to use the Four Slot Battery Charger to charge up to four MC65 batteries. Battery Charging 1. Connect the charger to a power source. 2. Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact. Battery Battery Charging LEDs (4) Figure 10-7 Four Slot Battery Charger Battery Charging Indicators The charger has an amber LED for each battery charging well.
Accessories 10 - 11 Table 10-3 Battery LED Charging Indicators (Continued) LED Indication Slow Blinking Amber Battery is charging. Solid Amber Charging complete. Fast Blinking Amber Charging error. Cables This section describes how to set up and use the cables. The cables are available with a variety of connection capabilities.
10 - 12 MC65 User Guide Locking Tab Figure 10-8 Cable Cup Locking Tabs The MC65 amber Charge LED indicates the MC65 battery charging status. The 3600 mAh standard battery charges in less than six hours. See Table 1-1 on page 1-6 for charging status indications. 4. When charging is complete, push the two locking tab down and remove the cable from the MC65. LED Charge Indications The amber Charge LED on the MC65 indicates battery charging status. See Table 1-1 on page 1-6 for charging status indications.
Accessories 10 - 13 Vehicle Holder WARNING! Some countries prohibit the mounting of any electronic device in any location on the vehicle dashboard and or windshield. Be sure to check your local laws acceptable mounting areas before installing the auto mounting kit. Installation Reminders Figure 10-9 Vehicle Holder Mounting • Do not mount the vehicle holder where it will obscure the driver’s view of the road. • Do not mount the vehicle holder near the driver seat air bag deployment area.
10 - 14 MC65 User Guide Assembly 1. Insert the vehicle holder’s cradle plate to the holes on the back of the cradle. 2. Push the cradle down until both parts are engaged. Windshield Installation 1. Fix the suction cup mount to the selected area with the suction lever facing up. Suction Cup Mount Cradle Plate Cradle Figure 10-10 Windshield Installation 2. Flip the lever down to create a vacuum between the suction cup and the mounting surface. 3.
Accessories 10 - 15 Locking Tab Figure 10-11 Insert MC65 into Vehicle Holder 5. Connect the auto charger cable to the MC65 and slide the two locking tabs up to secure the cable cup to the MC65. 6. Connect the other end to the cigarette lighter socket. The LED indicator on the right side of the touch screen lights up orange during charging. Flat Surface Installation 1. Remove the plastic sheet on the bottom of the mounting disc. 2. Place the disc, sticky side down, on a clean flat surface.
10 - 16 MC65 User Guide Figure 10-13 Vehicle Holder Mounted on Flat Surface 7. Connect the auto charger cable to the MC65 and slide the two locking tabs up to secure the cable cup to the MC65. 8. Connect the other end to the cigarette lighter socket. The LED indicator on the right side of the touch screen lights up orange during charging.
Chapter 11 Maintenance & Troubleshooting Introduction This chapter includes instructions on cleaning and storing the MC65, and provides troubleshooting solutions for potential problems during MC65 operation. Maintaining the MC65 For trouble-free service, observe the following tips when using the MC65: • Do not scratch the screen of the MC65. When working with the MC65, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen.
11 - 2 MC65 User Guide • A screen protector is applied to the MC65. Motorola recommends using this to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays. Benefits include: • Protection from scratches and gouges • Durable writing and touch surface with tactile feel • Abrasion and chemical resistance • Glare reduction • Keeping the device’s screen looking new • Quick and easy installation.
Maintenance & Troubleshooting 11 - 3 • To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF (0 ºC and +40 ºC) • Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Enterprise Mobility support.
11 - 4 MC65 User Guide • Isopropyl alcohol • Can of compressed air with a tube. Cleaning the MC65 Housing Using the alcohol wipes, wipe the housing including keys and in-between keys. Display The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
Maintenance & Troubleshooting 11 - 5 CAUTION Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face. 6. Ensure that there is no lint left by the cotton tipped applicator, remove lint if found. 7. If grease and other dirt can be found on other areas of the cradle, use lint free cloth and alcohol to remove. 8. Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
11 - 6 MC65 User Guide Table 11-1 Troubleshooting the MC65 (Continued) Problem Cause Solution MC65 removed from cradle or disconnected from host computer during communication. Replace the MC65 in the cradle, or reattach the communication cable and re-transmit. Incorrect cable configuration. See the system administrator. Communication software was incorrectly installed or configured. Perform setup. Refer to the MC65 Integrator Guide for details. No sound. Volume setting is low or turned off.
Maintenance & Troubleshooting 11 - 7 Table 11-1 Troubleshooting the MC65 (Continued) Problem The MC65 does not decode with reading bar code. Cause Solution Scanning application is not loaded. Load a scanning application on the MC65. See your system administrator. Unreadable bar code. Ensure the symbol is not defaced. Distance between exit window and bar code is incorrect. Place the MC65 within proper scanning range. MC65 is not programmed for the bar code.
11 - 8 MC65 User Guide Single Slot USB Cradle Table 11-3 Troubleshooting the Single Slot USB Cradle Symptom LEDs do not light when MC65 or spare battery is inserted. MC65 battery is not charging. Spare battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action Cradle is not receiving power. Ensure the power cable is connected securely to both the cradle and to AC power. MC65 is not seated firmly in the cradle.
Maintenance & Troubleshooting 11 - 9 Four Slot Ethernet Cradle Table 11-4 Troubleshooting the Four Slot Ethernet Cradle Symptom Cause Solution During communication, no data transmits, or transmitted data was incomplete. MC65 removed from cradle during communications. Replace MC65 in cradle and retransmit. MC65 has no active connection. An icon is visible in the status bar if a connection is currently active. Battery is not charging. MC65 removed from the cradle too soon.
11 - 10 MC65 User Guide Four Slot Battery Charger r Table 11-6 Troubleshooting The Four Slot Battery Charger Symptom Possible Cause Action Battery not charging. Battery was removed from the charger or charger was unplugged from AC power too soon. Re-insert the battery in the charger or re-connect the charger’s power supply. The 3600 mAh battery fully charges in less than six hours. Battery is faulty. Verify that other batteries charge properly. If so, replace the faulty battery.
Maintenance & Troubleshooting 11 - 11 Magnetic Stripe Reader Table 11-8 Troubleshooting the Magnetic Stripe Reader Symptom MSR cannot read card. MC65 battery is not charging. During data communication, no data transmits, or transmitted data was incomplete. Possible Cause Action MSR removed from MC65 during card swipe. Reattach MSR to MC65 and reswipe the card. Faulty magnetic stripe on card. See the system administrator. MSR application is not installed or configured properly.
11 - 12 MC65 User Guide
Appendix A Technical Specifications MC65 Technical Specifications The following tables summarize the EDA’s intended operating environment and technical hardware specifications. MC65 Table A-1 MC65 EDA Technical Specifications Item Description Physical Characteristics Dimensions Height: 16.2 cm (6.38 in.) Width: 7.7 cm (3.03 in.) Depth: 3.4 cm (1.32 in.) Weight 359 g (12.5 oz.) Display Transflective color 3.
A-2 MC65 User Guide Table A-1 MC65 EDA Technical Specifications (Continued) Item Description Performance Characteristics CPU MSM Qualcomm 7627@ 600 MHz (multi-processor architecture) Operating System Microsoft® Windows Mobile™ 6.5 Professional Memory 256 MB RAM/1 GB Flash Output Power USB - 5 VDC @ 300 mA max.
Technical Specifications A-3 Table A-1 MC65 EDA Technical Specifications (Continued) Item Description Frequency Band UMTS/HSDPA and HSUPA: 850, 1900 and 2100 MHz GSM/EDGE: 850, 900, 1800 and 1900 MHz CDMA/EVDO Rev A: 850 and 1900 MHz Antenna External Wireless LAN Data and Voice Communications Radio Tri-mode IEEE® 802.11a/b/g Data Rates Supported 1, 2, 5.
A-4 MC65 User Guide Table A-1 MC65 EDA Technical Specifications (Continued) Item Description Wireless Wide Area Network GSM-HSDPA Global: 3GPP TS 51.010, 3GPP TS 34.121, 3GPP TS 34.123, GCF and PTCRB approved module USA: FCC Part 22, Part 24 Canada: RSS-132, RSS-133 EU: EN 301 511, EN 301 908 Australia: AS/ACIF S 024.
Technical Specifications A-5 Table A-1 MC65 EDA Technical Specifications (Continued) Item Description Illumination Element (LED) 625 nm +/- 5 nm Camera Specifications Resolution 3.
A-6 MC65 User Guide Table A-2 Data Capture Options (Continued) Item Camera Decode Capability Description Code 39 Codabar Discrete 2 of 5 EAN-13 UPC/EAN supplementals Webcode Composite C Macro PDF-417 Data Matrix US Planet Canadian 4-state GS1 DataBar GS1 DataBar Truncated GS1 DataBar Expanded GS1 DataBar Stacked Omni Code 128 Code 11 MSI UPCA Coupon Code TLC39 Micro PDF-417 (Macro) Micro PDF-417 Maxi Code UK 4-state Japanese 4-state Code 93 Interleaved 2 of 5 EAN-8 UPCE Trioptic 39 Composite AB PDF-41
Technical Specifications Four Slot Battery Charger Table A-4 Four Slot Battery Charger Technical Specifications Feature Description Dimensions Height: 4.7 cm (1.85 in.) Width: 15.5 cm (6.10 in.) Depth: 21.0 cm (8.27 in.) Weight 384 g (13.55 oz) Input Voltage 12 VDC Power Consumption 30 watts Operating Temperature 0°C to 40°C (32°F to 104°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Charging Temperature 0°C to 40°C (32°F to 104°F) Humidity 5% to 95% non-condensing Drop 76.
A-8 MC65 User Guide Table A-5 Four Slot Charge Only Cradle Technical Specifications (Continued) Feature Description Humidity 5% to 95% non-condensing Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Four Slot Ethernet Cradle Table A-6 Four Slot Ethernet Cradle Technical Specifications Feature Description Dimensions Height: 13.7 cm (5.39 in.) Width: 46.8 cm (18.43 in.) Depth: 9.9 cm (3.90 in.
Technical Specifications Table A-7 Magstripe Reader (MSR) Technical Specifications (Continued) Feature Description Mode Buffered, unbuffered Track Reading Capabilities Tracks 1 and 3: 210 bpi Track 2: 75 and 210 bpi, autodetect Operating Temperature 32° to 122° F (0° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Humidity 5% to 95% non-condensing Drop 4 ft. (1.
A - 10 MC65 User Guide Cables Table A-9 USB Charging Cable Technical Specifications Feature Description Length 161.9 cm (63.74 in.) Operating Temperature -10°C to 50°C (14°F to 122°F) Storage Temperature -40°C to 70°C (-40°F to 158°F) Humidity 10% to 95% non-condensing Electrostatic Discharge (ESD) +/- 15 kV air +/- 8 kV contact Table A-10 Charge Only Cable Technical Specifications Feature Description Length 28.0 cm (11.00 in.
Appendix B Keypads Introduction The MC65 offers four types of keypad configurations: Numeric, QWERTY, QWERTZ and AZERTY. Numeric Keypad Configuration The numeric keypad contains application keys, scroll keys, and function keys. The keypad is color-coded to indicate the alternate function key (blue) values. Note that an application can change keypad functions so the MC65’s keypad may not function exactly as described.
B-2 MC65 User Guide Table B-1 MC65 Numeric Keypad Descriptions Key Blue Key Description Use this key to launch applications or access items (shown on the keypad in blue). Press the Blue key once to activate this mode, followed by another key. A single press illuminates the key and displays the following icon at the bottom of the screen, until a second key is pressed: Orange Key Use this key to access the secondary layer of characters and actions (shown on the keypad in orange).
Keypads B-3 Table B-1 MC65 Numeric Keypad Descriptions (Continued) Key Description Soft Keys Accesses the command or menu above it on the screen. Star Produces an asterisk in default state. Press and release the blue key, then press the Star key to open the Start menu. Alphanumeric In default state, produces the numeric value on the key. In Alpha state, produces the lower case alphabetic characters on the key. Each key press produces the next alphabetic character in sequence.
B-4 MC65 User Guide Table B-2 Numeric Keypad Input Modes Orange Key (Alpha Lowercase Mode) Numeric Mode Orange + Shift Keys (Alpha Uppercase Mode) Key Blue+ Key SHIFT + Key 1st Press 2nd Press 3rd Press 4th Press * 1st Press 2nd Press 3rd Press 4th Press * * * * 1 1 F1 ! * * * 2 2 F2 @ a b c A B C 3 3 F3 # d e f D E F 4 4 F4 $ g h i G H I 5 5 F5 % j k l J K L 6 6 F6 ^ m n o M N O 7 7 F7 & p q r P Q R 8 8 F8 * t u v
Keypads Figure B-2 QWERTY Keypad Configuration Figure B-3 AZERTY Keypad Configuration Figure B-4 QWERTZ Keypad Configuration B-5
B-6 MC65 User Guide Table B-3 Alpha-numeric Keypad Descriptions Key Blue Key Action Press the Blue key once to activate this mode temporarily, followed by another key. This displays the following icon at the bottom of the screen, until a second key is pressed: Press the Blue key twice to lock this mode. This displays the following icon at the bottom of the screen: Press the Blue key a third time to unlock.
Keypads B-7 Table B-3 Alpha-numeric Keypad Descriptions (Continued) Key Action Scroll Down and Right Moves down one item. Moves right one item when pressed with the Orange key. Soft Keys Accesses the command or menu above it on the screen. Shift Changes the state of the alpha characters from lowercase to uppercase. • Press the Shift key to activate this mode temporarily, followed by another key.
B-8 MC65 User Guide Table B-4 QWERTY Keypad Input Modes Key Normal Shift + Key Orange + Key Blue + Key Q q Q * q W w W 1 w E e E 2 e R r R 3 r T t T + t Y y Y _ y U u U - u I i I = i O o O “ o P p P áü p A a A # a S s S 4 s D d D 5 d F f F 6 f G g G ( g H h H ) h J j J / j K k K : k L l L ‘ l Backspace Backspace Backspace Backspace Backspace Shift Shift Shift-Lock Shift Shift Z z Z 7 z X x
Keypads B-9 Table B-4 QWERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key , , < @ , ENTER Enter Enter Enter Enter 0 0 ) 0 0 TAB Tab Tab Back tab Tab SPACE Space Space Space Space Backlight Backlight Backlight Backlight Backlight . (Period) . > . . Note: An application can change the key functions. The keypad may not function exactly as described.
B - 10 MC65 User Guide Table B-5 AZERTY Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key L l L ‘ l Backspace Backspace Backspace Backspace Backspace Shift Shift Shift-Lock Shift Shift W w W 7 w X x X 8 x C c C 9 c V v V % v B b B & b N n N ! n M m M ? m , , < @ Enter Enter Enter Enter Enter 0 0 ) 0 0 TAB Tab Tab Back tab Tab SPACE Space Space Space Space Backlight Backlight Backlight Backlight B
Keypads B - 11 Table B-6 QWERTZ Keypad Input Modes (Continued) Key Normal Shift + Key Orange + Key Blue + Key O o O “ o P p P áü p A a A # a S s S 4 s D d D 5 d F f F 6 f G g G ( g H h H ) h J j J / j K k K : k L l L ‘ l Backspace Backspace Shift Shift Y y Y 7 y X x X 8 x C c C 9 c V v V % v B b B & b N n N ! n M m M ? m , , < @ , ENTER Enter ENTER ENTER Enter 0 0 ) 0 0 TAB Tab Tab Back tab
B - 12 MC65 User Guide Special Character Key NOTE Special characters are only available on the alpha-numeric keypad configurations. To add special characters using the MC65 áü key, type the related character first, then press the Orange twice followed by the áü (P) key. Continue pressing the áü key until the special character displays.
Keypads B - 13 Table B-7 Special Characters (Continued) Key ? - Special Characters Key : Special Characters
B - 14 MC65 User Guide
Appendix C Windows Mobile Home Screen and Dialer Introduction The appendix describes the functionality of the optional Windows Mobile Home screen and Dialer. Windows Mobile Home Screen The Windows Mobile Home screen is scrollable and contains a list of application plug-ins and an Information Status bar. The Information Status bar highlights the application plug-in that is under it and provides additional information.
C-2 MC65 User Guide Touch and hold the screen with your finger and move the Home screen up and down. As the application names move under the Information Status bar, information relevant to that application appear in the bar. Figure C-2 Moving Today Screen You can also touch and hold the Information Status bar and move it up and down over an application name. Remove your finger and the Information Status bar and application name center in the screen.
Windows Mobile Home Screen and Dialer Application Icon Application Information Figure C-4 Information Bar Example To customize the Home screen, tap Start > Settings > Today. On the horizontal scroll, use Appearance to customize the background and the Items to change the display format. Classic Today Screen The user can change the Today screen to the classic layout that is used in Windows Mobile 6.1.
C-4 MC65 User Guide Figure C-6 Home Screen Settings Deselect the Windows Default checkbox and select any of the other checkboxes except for Motorola Home. Tap OK. The task bar at the bottom of the screen can contain the task tray icons listed in Table C-1. Table C-1 Task Tray Icons Icon Name Description Wireless connection status Indicates WLAN signal strength. ActiveSync Active serial connection between the MC75A and the host computer.
Windows Mobile Home Screen and Dialer 3. Select Microsoft Dialer. 4. Tap Save. 5. Tap OK. The MC65 reboots. C-5 Making a Call NOTE You can make emergency calls even when the MC65 is locked or when a SIM card is not installed. See Emergency Calling on page C-9 for more information. With the MC65, you can make a call from the phone, contacts, speed dial and call history. Using the Phone Keypad To make a call using the phone keypad: 1. Press . 2. Enter the phone number on the dialer or keypad.
C-6 MC65 User Guide the Phone keypad, contact names such as the following will be considered matches: “Smith, Bernard”, “Adams, John”, “Carlson, Eileen”, “Dillon, Albert”, “Childs, Larry”, “Cooper, Robert” and “Parks, Celine”. • If the matching list is long narrow down the search further by entering another letter. Using the same example above, tap “3” which is associated with (d, e, f), the matching list is narrowed down to the following names: “Smith, Bernard”, “Adams, John”, and “Parks, Celine”.
Windows Mobile Home Screen and Dialer C-7 Figure C-8 Contacts Menu 3. Tap Call Work, Call Home or Call Mobile. NOTE To make a call from an open contact, tap the number to call. See On-Device Help for more information about Contacts. Using Call History To make a call using Call History: 1. Press . 2. From the Phone keypad, tap Call History. Phone icon Figure C-9 Call History Window 3. Tap the phone icon next to the number to begin dialing and return to the phone keypad. 4.
C-8 MC65 User Guide Making a Speed Dial Call Use Speed Dial to call someone saved in the speed dial directory. To make a speed dial call: 1. Press . 2. From the keypad, tap and hold the speed dial location number assigned to a contact. (To dial a one-digit speed dial location number, tap and hold the speed dial number. To dial a two-digit speed dial location number, tap the first digit and then tap and hold the second digit.
Windows Mobile Home Screen and Dialer To end the call press C-9 . ok Incoming Call Features • You can use other programs on the MC65 during a call. To switch back to the Phone, press Start > Phone. Tap ok or tap to end the call. • If a caller isn't in your contact list, create a contact during the call or from Call History by tapping Menu > Save to Contacts.
C - 10 MC65 User Guide • Headset Mode: Connect a Bluetooth headset or a wired headset to automatically switch audio to the headset. The MC65 defaults to handset mode. When a wired headset is plugged into the MC65 headset connector or a Bluetooth headset is configured for use with the MC65, the earpiece and speakerphone are muted and audio is heard through the headset. NOTE While using a Bluetooth headset during a call, the MC65 will not go into suspend mode.
Windows Mobile Home Screen and Dialer C - 11 NOTE Adjust the conversation phone volume during a call. Adjusting the volume while not in a call affects the ring and notification sound levels. Muting a Call During a call, you can mute the microphone so you can hear the person on the line but he or she cannot hear conversation from the microphone. This is useful when there is conversation or background noise on your end. To mute or unmute a call, tap Mute on the dialer to mute the audio.
C - 12 MC65 User Guide 3. Tap . 4. Select Call Timers... . Figure C-13 Call History - Call Timers 5. Tap Reset. (The All Calls: counter cannot be reset.) 6. Tap OK to exit the Call Timers window. Deleting All Call History Items 1. Press to display the Phone dialer. 2. From the Phone dialer, tap Call History. 3. Tap 4. Select Delete all calls. 5. Tap Yes. 6. Tap OK to exit the Call History window. . Viewing Call Status 1. Press to display the Phone dialer. 2.
Windows Mobile Home Screen and Dialer C - 13 Figure C-14 Call History - Detail NOTE 4. When more than one call is on the phone line, only the duration of the first call is recorded. Tap OK and then OK to exit. Using the Call History Menu Use the Call History menu to dial voice mail, access the Activation Wizard, save to contacts, view a note, delete a listing, send an SMS, and make a call. 1. Press to display the Phone dialer. 2. From the Phone dialer, tap Call History. 3.
C - 14 MC65 User Guide Swapping Calls (GSM) To move between two phone calls: 1. Press to display the Phone dialer. 2. Enter the first phone number and press Talk. When the call connects, Hold appears on the dialer. 3. Tap Hold on to place the first number on hold. 4. Enter the second number and tap Talk. Figure C-16 Call Conferencing - Conferencing 5. Tap Swap to move from one call to the other. 6. Tap End or press ok to end each call.
Windows Mobile Home Screen and Dialer C - 15 2. When a second call arrives, tap Answer. The first call is placed on hold. 3. Tap Flash to swap from one call to the other. Figure C-18 Call Swapping 4. Tap End or press the red phone key on the keypad to end active call. The remaining call re-connects, tap Answer to connect to the call. 5. Tap End or press the red phone key on the keypad to end the last call.
C - 16 MC65 User Guide NOTE To speak privately with one party during a conference call, tap > Private. To include all parties again, tap > Conference. Three-way Calling (CDMA) NOTE Three-way Calling may not be available on all services. Please check with your service provider for availability. To create a three-way phone session with two people and you as the initiator: 1. Press to display the Phone dialer. 2. Enter the first phone number and press Flash. 3. To call a second person, tap Keypad.
Glossary A API. (Application Programming Interface) An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls AZERTY. A standard keyboard commonly used on French keyboards. “AZERTY” refers to the arrangement of keys on the top row of keys. AKU. (Adaptation Kit Update) Updates to the Windows Mobile operating system. AFH.
Glossary - 2 MC55 User Guide bps. See Bits Per Second. Byte. On an addressable boundary, eight adjacent binary digits (0 and 1) combined in a pattern to represent a specific character or numeric value. Bits are numbered from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory is used to store one ASCII character. C CDRH. Center for Devices and Radiological Health. A federal agency responsible for regulating laser product safety.
Glossary - 3 Decryption. Decryption is the decoding and unscrambling of received encrypted data. Also see, Encryption and Key. Depth of Field. The range between minimum and maximum distances at which a scanner can read a symbol with a certain minimum element width. Device Configuration Package. The Symbol Device Configuration Package provides the Product Reference Guide (PRG), flash partitions, Terminal Configuration Manager (TCM) and the associated TCM scripts.
Glossary - 4 MC55 User Guide Host Computer. A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs and network control. I IEC. International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. IEC (825) Class 1. This is the lowest power IEC laser classification.
Glossary - 5 L LASER. Light Amplification by Stimulated Emission of Radiation.The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. laser scanner. A type of bar code reader that uses a beam of laser light. LCD. See Liquid Crystal Display. LED Indicator. A semiconductor diode (LED - Light Emitting Diode) used as an indicator, often in digital displays.
Glossary - 6 MC55 User Guide O Open System Authentication. Open System authentication is a null authentication algorithm. P PAN . Personal Area Network. Using Bluetooth wireless technology, PANs enable devices to communicate wirelessly. Generally, a wireless PAN consists of a dynamic group of less than 255 devices that communicate within about a 33-foot range. Only devices within this limited area typically participate in the network. PING.
Glossary - 7 SID. System Identification code. An identifier issued by the FCC for each market. It is also broadcast by the cellular carriers to allow cellular devices to distinguish between the home and roaming service. Space. The lighter element of a bar code formed by the background between bars. Specular Reflection. The mirror-like direct reflection of light from a surface, which can cause difficulty decoding a bar code. Start/Stop Character.
Glossary - 8 MC55 User Guide TFTP. (Trivial File Transfer Protocol) A version of the TCP/IP FTP (File Transfer Protocol) protocol that has no directory or password capability. It is the protocol used for upgrading firmware, downloading software and remote booting of diskless devices. Tolerance. Allowable deviation from the nominal bar or space width. Transmission Control Protocol/Internet Protocol. See TCP/IP. Trivial File Transfer Protocol. See TFTP. U UDP. User Datagram Protocol.
Index Numerics 2-D bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 3-Way Calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 A accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 auto charge cable . . . . . . . . . . . . . . . . . . . . . . . 10-2 cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 charge only cable . . . . . . . . . . . . . . . . . . . . . . . 10-1 communication/charge cables battery charging . .
Index - 2 MC65 User Guide discovering devices . . . . . . . . . . . . . . . . . . . . . . . 7-4 turning on and off . . . . . . . . . . . . . . . . . . . . . . . . 7-4 bullets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv buttons action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 power . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3, 2-20 scan . . . . . . . . .
Index - 3 ActiveSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7, 2-18 speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18 status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 task tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 wireless status . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 imager. See data capture, imaging imager.
Index - 4 MC65 User Guide button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 imaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 See data capture . . . . . . . . . . . . . . . . . . . . . . . . 2-22 screen calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 screen protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 SD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners. © Motorola, Inc.
