Symbol DS6708 Digital Scanner Product Reference Guide
Symbol DS6708 Digital Scanner Product Reference Guide 72E-86039-06 Revision A October 2009
ii Symbol DS6708 Digital Scanner Product Reference Guide © 2007-2009 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis.
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev A 01/2007 Initial Release. -02 Rev A 04/2007 Update service information, update operating temperature and drop specifications, remove sealing specification, correct Symbol PTC Terminal bar code, add new UPC/EAN supplemental options, Bookland ISBN format, 4State Postal, Aztec, and and inverse code type parameters, changed RSS references to GS1 DataBar. -03 Rev A 09/2007 Update decode ranges.
iv Symbol DS6708 Digital Scanner Product Reference Guide
Table of Contents Patents........................................................................................................................... ii Warranty ........................................................................................................................ ii Revision History ............................................................................................................. iii About This Guide Introduction .................................................................
vi Symbol DS6708 Digital Scanner Product Reference Guide Scanning in Presentation Mode .................................................................................... Scanning with the Digital Scanner in the Intellistand .............................................. Scanning with the Digital Scanner with Base .......................................................... Decode Zones ..............................................................................................................
Table of Contents Illumination Bank Control ........................................................................................ Decode Aiming Pattern ........................................................................................... Low Light Enhancement ......................................................................................... Presentation Mode Field of View ............................................................................
viii Symbol DS6708 Digital Scanner Product Reference Guide IBM Parameter Defaults ............................................................................................... IBM 468X/469X Host Parameters ................................................................................. Port Address ........................................................................................................... Convert Unknown to Code 39 ........................................................................
Table of Contents Code 39 Full ASCII Conversion .............................................................................. Transmission Timeout ............................................................................................. Ignore Unknown Characters ................................................................................... Leading Margin ....................................................................................................... Check For Decode LED ...................
x Symbol DS6708 Digital Scanner Product Reference Guide Enable/Disable Trioptic Code 39 ............................................................................ Convert Code 39 to Code 32 .................................................................................. Code 32 Prefix ........................................................................................................ Set Lengths for Code 39 .........................................................................................
Table of Contents Transmit UK Postal Check Digit .............................................................................. Japan Postal ........................................................................................................... Australian Postal ..................................................................................................... Netherlands KIX Code ...........................................................................................
xii Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes .............................................................................. AAMVA Parse Field Bar Codes (continued) ........................................................... Parsing Rule Example .................................................................................................. Field Update Procedure ................................................................................................
Table of Contents Appendix B: Programming Reference Symbol Code Identifiers ................................................................................................ B-1 AIM Code Identifiers ..................................................................................................... B-3 Appendix C: Sample Bar Codes Code 39 ........................................................................................................................ UPC/EAN ........................................
xiv Symbol DS6708 Digital Scanner Product Reference Guide
About This Guide Introduction The Symbol DS6708 Digital Scanner Product Reference Guide provides general instructions for setting up, operating, maintaining, and troubleshooting the Symbol DS6708 digital scanner. NOTE The Symbol DS6708 premier digital decoder does not support imaging. For imaging features and parameters, refer to the Symbol DS6707 Digital Imager Scanner Product Reference Guide, p/n 72E-83978-xx.
xvi Symbol DS6708 Digital Scanner Product Reference Guide • Chapter 7, RS-232 Interface describes how to set up the digital scanner with an RS-232 host, such as point-of-sale devices, host computers, or other devices with an available RS-232 port. • Chapter 9, Wand Emulation Interface describes how to set up the digital scanner with a Wand Emulation host. • Chapter 10, Keyboard Wedge Interface describes how to set up a Keyboard Wedge interface with the digital scanner.
About This Guide xvii • Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists. • Throughout the programming bar code menus, asterisks (*) are used to denote default parameter settings. * Indicates Default *Baud Rate 9600 Feature/Option Related Documents The Symbol DS6708 Quick Start Guide, p/n 72-83973-xx, provides general information for getting started with the Symbol DS6708 digital scanner, and includes basic set up and operation instructions.
xviii Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 1 Getting Started Introduction The Symbol DS6708 combines superior 1D and 2D omnidirectional bar code scanning and sub-second image capture. With support for a variety of commonly used interfaces, the DS6708 provides the best value in a digital scanner. Whether in hand-held mode or presentation mode, the digital scanner ensures comfort and ease of use for extended periods of time.
1-2 Symbol DS6708 Digital Scanner Product Reference Guide Supported Interfaces The DS 6708 digital scanner supports: • USB connection to a host. The digital scanner autodetects a USB host and defaults to the HID keyboard interface type. Select other USB interface types by scanning programming bar code menus.
Getting Started 1-3 Setting Up the Digital Scanner Standard Model Installing the Interface Cable 1. Plug the interface cable modular connector into the cable interface port on the bottom of the scanner handle (see Figure 1-3). 2. Gently tug the cable to ensure the connector is secure. 3. Connect the other end of the interface cable to the host (see the specific host chapter for information on host connections).
1-4 Symbol DS6708 Digital Scanner Product Reference Guide Connecting a Synapse Cable Interface (Symbol DS6708 0nly) NOTE Refer to the Synapse Interface Guide provided with the Synapse cable for detailed setup instructions. Synapse Smart Cables enable interfacing to a variety of hosts. The Synapse cable has built-in intelligence to detect that host. To host Synapse Adapter Cable Synapse Smart Cable To digital scanner Figure 1-5 Synapse Cable Connection 1.
Getting Started 1-5 Model with Base Installing the Interface Cable 1. Turn both angle adjustment knobs left to loosen the scanner in the base. See Figure 1-6. 2. Move the scanner forward until there is full access to the cable interface port on the bottom of the scanner. See Figure 1-3 or Figure 1-5. Angle Adjustment Knob (2) Figure 1-6 Adjust the Scanner for Cable Installation 3. Insert the interface cable through the opening at the back of the base.
1-6 Symbol DS6708 Digital Scanner Product Reference Guide Configuring the Digital Scanner To configure the digital scanner, use the bar codes included in this manual, or the 123Scan configuration program. See Chapter 4, User Preferences & Miscellaneous Digital Scanner Options and Chapter 5, Decoding Preferences for information about programming the digital scanner using bar code menus. Also see each host-specific chapter to set up connection to a specific host type.
Getting Started 1-7 Wall Mount To use the optional wall mount to mount the digital scanner on a wall, place the mount in the desired location on the wall and secure by inserting two screws* appropriate for the mounting surface through the screw holes on the mount, and into the surface. Insert the digital scanner into the mount as shown. Figure 1-8 Securing the Wall Mount *The recommended screws are two #6 screws (1” long) and two #6 washers.
1-8 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 2 Scanning Introduction This chapter provides beeper and LED definitions, techniques involved in scanning bar codes, general instructions and tips about scanning, and decode zone diagrams.
2-2 Symbol DS6708 Digital Scanner Product Reference Guide Beeper Definitions The digital scanner issues different beep sequences and patterns to indicate status. Table 2-1 defines beep sequences that occur during both normal scanning and while programming the digital scanner. Table 2-1 Beeper Definitions Beeper Sequence Indication Standard Use Low/medium/high beeps Power up. Short high beep A bar code symbol was decoded (if decode beeper is enabled).
Scanning 2-3 Table 2-1 Beeper Definitions (Continued) Beeper Sequence Indication Fast warble beep Aborting MPDF sequence. Low/high beeps Flushing an already empty MPDF buffer. ADF Programming: Normal Data Entry. Duration of tones are short. High/low beeps Enter another digit. Add leading zeros to the front if necessary. Low/low beeps Enter another alphabetic character or scan the End of Message bar code. High/high beeps Enter another criterion or action, or scan the Save Rule bar code.
2-4 Symbol DS6708 Digital Scanner Product Reference Guide LED Definitions In addition to beep sequences, the digital scanner uses a two-color LED to indicate status. Table 2-2 defines LED colors that display during scanning. Table 2-2 Standard LED Definitions LED Indication Off No power is applied to the digital scanner, or the digital scanner is on and ready to scan. Green A bar code was successfully decoded. Red A data transmission error or digital scanner malfunction occurred.
Scanning 4. 2-5 Center the symbol in any orientation within the aiming pattern. Be sure the entire symbol is within the rectangular area formed by the brackets in the pattern. 2D barsymbol code PDF417 1D bar Linear barcode code Symbol Aiming Pattern Figure 2-12 Centering Symbol in Aiming Pattern 5. Hold the trigger until the digital scanner beeps, indicating the bar code is successfully decoded. For more information on beeper and LED definitions, see Table 2-1 and Table 2-2.
2-6 Symbol DS6708 Digital Scanner Product Reference Guide Scanning in Presentation Mode Scanning with the Digital Scanner in the Intellistand The optional Intellistand adds greater flexibility to scanning operation. When you place the digital scanner in the stand’s “cup,” the digital scanner’s built-in sensor places the digital scanner in presentation mode. When you remove the digital scanner from the stand it operates in its normal hand-held mode.
Scanning 2-7 Scanning with the Digital Scanner with Base The DS6707 digital scanner with base (DS670X-SR2000XNSR) offers the flexibility of switching between presentation (hands-free) mode and hand-held mode. The default mode is presentation mode. Figure 2-15 Scanning in Presentation Mode Scanning with the Digital Scanner 1. Ensure all connections are secure (see the appropriate host chapter). 2. Use the base adjustment knobs to adjust the angle of the digital scanner. 3.
2-8 Symbol DS6708 Digital Scanner Product Reference Guide Decode Zones O O Note: Typical performance at 73.4 F (23 C) on high quality symbols. DS6708 5 mil (Code 39) 5.4 In . cm 10 3 1 .6 5 12.7 W i d t h 0 0 o f 5 12.7 0.9 10 mil I 2 of 5 1.0 7.9 10 25.4 F i e l d 13 mil (100% UPC/EAN) 8.4 0.9 20 mil (Code 39) 0.9 12.9 Postnet 2.6 In . 0 cm 0 5 12.7 10 25.4 12.5 15 38.
Scanning O O Note: Typical performance at 73.4 F (23 C) on high quality symbols. In . DS6708 cm 10 3 1 .6 5 12.7 W i d t h 0 0 o f 5 12.7 6.6 mil PDF417 5.2 1.4 10 10 mil QR Code 25.4 F i e l d 6.8 2.6 PDF417 (10 mil) 6.2 1.4 10 mil MicroPDF 2.3 7.50 Datamatrix (10 mil) 7.50 35 mil Maxicode 1.5 1.10 In . 0 cm 0 5 12.7 10 25.4 12.8 15 38.
2 - 10 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 3 Maintenance & Technical Specifications Introduction This chapter provides suggested scanner maintenance, troubleshooting, technical specifications, and signal descriptions (pinouts). Maintenance Cleaning the scan window is the only maintenance required. A dirty window can affect scanning accuracy. • Do not allow abrasive material to touch the window. • Remove any dirt particles with a damp cloth. • Wipe the window using a tissue moistened with ammonia/water.
3-2 Symbol DS6708 Digital Scanner Product Reference Guide Troubleshooting Table 3-1 Troubleshooting Problem The aiming pattern does not appear when pressing the trigger. Possible Causes Possible Solutions No power to the digital scanner. If the configuration requires a power supply, re-connect the power supply. Incorrect host interface cable is used. Connect the correct host interface cable. Interface/power cables are loose. Re-connect cables. Digital scanner is disabled.
Maintenance & Technical Specifications 3-3 Table 3-1 Troubleshooting (Continued) Problem Possible Causes Possible Solutions Digital scanner decodes bar code, but does not transmit the data to the host. Digital scanner is not programmed for the correct host type. Scan the appropriate host type programming bar code. See the chapter corresponding to the host type. Interface cable is loose. Re-connect the cable. If 4 long low beeps are heard, a transmission error occurred.
3-4 Symbol DS6708 Digital Scanner Product Reference Guide Table 3-1 Troubleshooting (Continued) Problem Possible Causes Possible Solutions Digital scanner emits low/high/low beeps. Clearing Code 39 buffer. Normal when scanning the Code 39 Buffering Clear Buffer bar code or upon attempt to transmit an empty Code 39 buffer. Digital scanner emits a power-up beep after changing USB host type. The USB bus re-established power to the digital scanner. Normal when changing USB host type.
Maintenance & Technical Specifications 3-5 Technical Specifications Table 3-2 Technical Specifications Item Description Physical Characteristics Dimensions (For Scanner Only; Not Including Base) 6.55 in. x 4.72 in. x 2.82 in. (16.6 cm x 11.9 cm x 7.1 cm) (H x L x W) Weight: 6.4 oz.
3-6 Symbol DS6708 Digital Scanner Product Reference Guide Table 3-2 Technical Specifications (Continued) Item Description Typical Working Distance 5 mil (Code 39): 10 mil (I 2 of 5): 13 mil (100% UPC/EAN): Postnet 20 mil (Code 39): PDF417 (6.6 Mil): QR Code (10 Mil) PDF417 (10 Mil): MicroPDF (10 Mil) Data Matrix (10 Mil): Maxicode (35 Mil): 0.9 - 5.4 in. (2.3 - 13.7 cm) 1.0 - 7.9 in. (2.5 - 20.1 cm) 0.9 - 8.4 in. (2.3 - 21.3 cm) 2.6 - 12.5 in. (6.6 - 31.8 cm) 0.9 - 12.9 in. (2.3 - 32.8 cm) 3.4 - 5.
Maintenance & Technical Specifications 3-7 Digital Scanner Signal Descriptions Bottom of digital scanner Cable interface port Pin 10 Pin 1 Interface cable modular connector Figure 3-1 Digital Scanner Cable Pinouts The signal descriptions in Table 3-3 apply to the connectors on the Symbol DS6708 digital scanner and are for reference only.
3-8 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 4 User Preferences & Miscellaneous Digital Scanner Options Introduction You can program the digital scanner to perform various functions, or activate different features. This chapter describes each user preference feature and provides programming bar codes for selecting these features. The digital scanner ships with the settings shown in Table 4-1 on page 4-2 (also see Appendix A, Standard Default Parameters for all host device and miscellaneous defaults).
4-2 Symbol DS6708 Digital Scanner Product Reference Guide Scanning Sequence Examples In most cases, scanning one bar code sets the parameter value. For example, to set the beeper tone to high, scan the High Frequency (beeper tone) bar code listed under Beeper Tone on page 4-6. The digital scanner issues a fast warble beep and the LED turns green, signifying a successful parameter entry. Other parameters, such as Serial Response Time-Out or Data Transmission Formats, require scanning several bar codes.
User Preferences & Miscellaneous Digital Scanner Options Table 4-1 User Preferences Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Beep After Good Decode 38h Enable 4-14 Fuzzy 1D Processing F1h, 02h Enable 4-14 Decode Mirror Images F1h, 19h Never 4-15 Transmit Code ID Character 2Dh None 4-16 Prefix Value 63h, 69h 7013 4-17 Suffix 1 Value Suffix 2 Value 62h, 68h 64h, 6Ah 7013 4-17 Scan Data Transmission Format EBh Data as is 4-
4-4 Symbol DS6708 Digital Scanner Product Reference Guide User Preferences Set Default Parameter Scan this bar code to return all parameters to the default values listed in Table A-1 on page A-1. You can reset the digital scanner to two types of defaults: factory defaults or custom defaults. Scan the appropriate bar code below to reset the scanner to its default settings and/or set its current settings as custom defaults. • Restore Defaults - Scan this bar code to reset all default parameters as follows.
User Preferences & Miscellaneous Digital Scanner Options 4-5 Parameter Scanning Parameter # ECh To disable decoding of parameter bar codes, including the Set Defaults parameter bar codes, scan the Disable Parameter Scanning bar code below. To re-enable decoding of parameter bar codes, scan Enable Parameter Scanning.
4-6 Symbol DS6708 Digital Scanner Product Reference Guide Beeper Tone Parameter # 91h To select a decode beep frequency (tone), scan the Low Frequency, Medium Frequency, or High Frequency bar code.
User Preferences & Miscellaneous Digital Scanner Options 4-7 Beeper Volume Parameter # 8Ch To select a beeper volume, scan the Low Volume, Medium Volume, or High Volume bar code. Low Volume (02h) Medium Volume (01h) *High Volume (00h) Power Mode Parameter # 80h This parameter determines whether or not power remains on after a decode attempt. In reduced power mode, the digital scanner enters into a low power consumption mode to preserve battery life after each decode attempt.
4-8 Symbol DS6708 Digital Scanner Product Reference Guide Time Delay to Low Power Mode Parameter # 92h NOTE This parameter only applies when Power Mode is set to Reduced Power. This parameter sets the time the digital scanner remains active after decoding. The digital scanner wakes upon trigger pull or when the host attempts to communicate with the digital scanner.
User Preferences & Miscellaneous Digital Scanner Options 4-9 Trigger Mode Parameter # 8Ah Select one of the following trigger modes for the digital scanner: • Level - A trigger pull activates decode processing. Decode processing continues until the bar code decodes, you release the trigger, or the Decode Session Timeout occurs. • Blink - This trigger mode is used in presentation (scanstand) mode. The digital scanner activates decode processing when it detects a bar code in its field of view.
4 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Picklist Mode Parameter # F0h 92h Picklist mode enables the digital scanner to decode only bar codes that are aligned under the laser crosshair. Select one of the following picklist modes for the digital scanner: • Disabled Always - Picklist mode is always disabled. • Enabled Out of Scanstand - Picklist mode is enabled when the digital scanner is out of presentation mode and disabled when the digital scanner is in presentation mode.
User Preferences & Miscellaneous Digital Scanner Options 4 - 11 Presentation Mode Parameter # F1h, 74h This parameter sets the time the digital scanner remains in hand-held mode before reverting back to the default presentation (hands-free) mode. Scanning Disable enables hand-held mode. To re-enable presentation (hands-free) mode, scan the desired time delay bar code.
4 - 12 Symbol DS6708 Digital Scanner Product Reference Guide Presentation Mode (continued) 7 Sec 8 Sec 9 Sec 10 Sec
User Preferences & Miscellaneous Digital Scanner Options 4 - 13 Decode Session Timeout Parameter # 88h This parameter sets the maximum time decode processing continues during a scan attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The default timeout is 9.9 seconds. To set a Decode Session Timeout, scan the bar code below. Next, scan two numeric bar codes from Appendix D, Numeric Bar Codes that correspond to the desired on time. Enter a leading zero for single digit numbers.
4 - 14 Symbol DS6708 Digital Scanner Product Reference Guide Beep After Good Decode Parameter # 38h Scan a bar code below to select whether or not the digital scanner beeps after a good decode. If selecting Do Not Beep After Good Decode, the beeper still operates during parameter menu scanning and to indicate error conditions.
User Preferences & Miscellaneous Digital Scanner Options 4 - 15 Decode Mirror Images (Data Matrix Only) Parameter # F1h 19h Select an option for decoding mirror image Data Matrix bar codes: • Always - decode only Data Matrix bar codes that are mirror images • Never - do not decode Data Matrix bar codes that are mirror images • Auto - decode both mirrored and unmirrored Data Matrix bar codes.
4 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Miscellaneous Scanner Parameters Transmit Code ID Character Parameter # 2Dh A Code ID character identifies the code type of a scanned bar code. This is useful when decoding more than one code type. In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. Select no Code ID character, a Symbol Code ID character, or an AIM Code ID character.
User Preferences & Miscellaneous Digital Scanner Options 4 - 17 Prefix/Suffix Values Key Category Parameter # P = 63h, S1 = 62h, S2 = 64h Decimal Value Parameter # P = 69h, S1 = 68h, S2 = 6Ah You can append a prefix and/or one or two suffixes to scan data for use in data editing. To set a value for a prefix or suffix, scan a four-digit number (i.e., four bar codes from Appendix D, Numeric Bar Codes) that corresponds to that value. See Table E-1 on page E-1 for the four-digit codes.
4 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Scan Data Transmission Format Parameter # EBh To change the scan data format, scan one of the following eight bar codes corresponding to the desired format. NOTE If using this parameter do not use ADF rules to set the prefix/suffix. To set values for the prefix and/or suffix, see Prefix/Suffix Values on page 4-17.
User Preferences & Miscellaneous Digital Scanner Options 4 - 19 Scan Data Transmission Format (continued) (05h) (06h) (07h) FN1 Substitution Values Key Category Parameter # 67h Decimal Value Parameter # 6Dh The Wedge and USB HID Keyboard hosts support a FN1 Substitution feature. Enabling this substitutes any FN1 character (0x1b) in a GS1-128 bar code with a value. This value defaults to 7013 (Enter Key).
4 - 20 Symbol DS6708 Digital Scanner Product Reference Guide Transmit “No Read” Message Parameter # 5Eh Scan a bar code below to select whether or not to transmit a No Read message. Enable this to transmit the characters NR when a bar code does not decoded. Disable this to send nothing to the host if a symbol does not decode.
User Preferences & Miscellaneous Digital Scanner Options 4 - 21 Synapse Interface Parameter # F0h, ACh The auto-detection of a Synapse cable varies in duration depending on the type of Synapse connection. If you connected a digital scanner to another scanner using a Synapse cable, use the Auxiliary Synapse Port connection. In all other cases, when using the cable, the default setting is recommended.
4 - 22 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 5 Decoding Preferences Introduction You can program the digital scanner to perform various functions, or activate different features. This chapter describes decoding preference features and provides programming bar codes for selecting these features. The digital scanner ships with the settings shown in the Decoding Preferences Parameter Defaults on page 5-2 (also see Appendix A, Standard Default Parameters for all host device and miscellaneous defaults).
5-2 Symbol DS6708 Digital Scanner Product Reference Guide Scanning Sequence Examples In most cases scanning one bar code sets the parameter value. For example, to disable the decode aiming pattern, scan the Disable Decode Aiming Pattern bar code listed under Decode Aiming Pattern on page 5-5. The digital scanner issues a fast warble beep and the LED turns green, signifying a successful parameter entry. Other parameters require scanning several bar codes.
Decoding Preferences 5-3 Decoding Preferences The parameters in this chapter control bar code decoding characteristics. Decoding Illumination Parameter # F0h, 2Ah Selecting Enable Decoding Illumination causes the digital scanner to flash illumination to aid decoding. Select Disable Decoding Illumination to prevent the digital scanner from using decoding illumination. Enabling illumination usually results in superior images.
5-4 Symbol DS6708 Digital Scanner Product Reference Guide Illumination Bank Control Parameter # F1h 3Bh Select an illumination bank control parameter to control the illumination banks on the scan engine. • Full (0) (default): Enable the full illumination system. • Auto (1): The illumination system automatically switches from left to right banks. • Left (2): The left bank is enabled. • Right (3): The right bank is enabled.
Decoding Preferences 5-5 Decode Aiming Pattern Parameter # F0h, 32h This parameter only applies in Decode Mode. Select Enable Decode Aiming Pattern to project the aiming pattern during bar code capture, or Disable Decode Aiming Pattern to turn the aiming pattern off. NOTE With Picklist Mode on page 4-10 enabled, the decode aiming pattern flashes even when the Decode Aiming Pattern is disabled.
5-6 Symbol DS6708 Digital Scanner Product Reference Guide Presentation Mode Field of View Parameter # F1h, 61h In presentation mode, the digital scanner searches for a bar code in a smaller region around the aiming pattern’s center cross to speed search time. To use a full field of view, scan Presentation Mode Full Field of View. This allows the digital scanner to search the larger area of the aiming pattern.
Chapter 6 USB Interface Introduction This chapter describes how to set up the digital scanner with a USB host. The digital scanner connects directly to a USB host, or a powered USB hub, which powers it. No additional power supply is required. Throughout the programming bar code menus, asterisks (*) indicate default values. *Indicates Default NOTE *North American Standard USB Keyboard Feature/Option Most computer monitors allow scanning the bar codes directly on the screen.
6-2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting a USB Interface USB Series A Connector Interface Cable Figure 6-1 USB Connection USB Series A Connector Interface Cable Figure 6-2 USB Connection for Scanner with Base The digital scanner connects with USB-capable hosts including: • Desktop PCs and notebooks • Apple™ iMac, G4, iBooks (North America only) • IBM SurePOS terminals • Sun, IBM, and other network computers that support more than one keyboard.
USB Interface 6-3 The digital scanner also interfaces with other USB hosts which support USB Human Interface Devices (HID). To set up the digital scanner: NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 6-1and Figure 6-2 are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner are the same. 1.
6-4 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-1 USB Interface Parameter Defaults (Continued) Parameter Default Page Number Function Key Mapping Disable 6-11 Simulated Caps Lock Disable 6-11 Convert Case None 6-12
USB Interface USB Host Parameters USB Device Type Select the desired USB device type. NOTE When changing USB Device Types, the digital scanner automatically resets and issues the standard startup beep sequences.
6-6 Symbol DS6708 Digital Scanner Product Reference Guide USB Country Keyboard Types - Country Codes Scan the bar code corresponding to the keyboard type. This setting applies only to the USB HID Keyboard Emulation device. NOTE When changing USB country keyboard types the digital scanner automatically resets and issues the standard startup beep sequences.
USB Interface USB Country Keyboard Types - Country Codes (continued) Spanish Windows Italian Windows Swedish Windows UK English Windows Japanese Windows (ASCII) Portuguese-Brazilian Windows 6-7
6-8 Symbol DS6708 Digital Scanner Product Reference Guide USB Keystroke Delay This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan a bar code below to increase the delay when hosts require a slower transmission of data. *No Delay Medium Delay (20 msec) Long Delay (40 msec) USB CAPS Lock Override This option applies only to the HID Keyboard Emulation device. Enable this to preserve the case of the data regardless of the state of the Caps Lock key.
USB Interface 6-9 USB Ignore Unknown Characters This option applies only to the HID Keyboard Emulation device and IBM device. Unknown characters are characters the host does not recognize. Select Send Bar Codes With Unknown Characters to send all bar code data except for unknown characters. The digital scanner issues no error beeps.
6 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Emulate Keypad with Leading Zero Enable this to send character sequences sent over the numeric keypad as ISO characters which have a leading zero. For example ASCII A transmits as “ALT MAKE” 0 0 6 5 “ALT BREAK”. *Disable Keypad Emulation with Leading Zero Enable Keypad Emulation with Leading Zero USB Keyboard FN 1 Substitution This option applies only to the USB HID Keyboard Emulation device.
USB Interface 6 - 11 Function Key Mapping ASCII values under 32 are normally sent as a control-key sequences (see Table 6-2 on page 6-13). Enable this parameter to send the keys in bold in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not you enable this parameter.
6 - 12 Symbol DS6708 Digital Scanner Product Reference Guide Convert Case Enable this to convert all bar code data to the selected case.
USB Interface 6 - 13 ASCII Character Set for USB Table 6-2 USB Prefix/Suffix Values Full ASCII Code 39 Encode Char.
6 - 14 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-2 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1025 $Y CTRL Y 1026 $Z CTRL Z 1027 %A CTRL [/ESC1 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL - 1032 Space Space 1033 /A ! 1034 /B “ 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . .
USB Interface 6 - 15 Table 6-2 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.
6 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-2 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.
USB Interface 6 - 17 Table 6-2 USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1The keystroke in bold transmits only if you enable Function Key Mapping on page 6-11. Otherwise, the unbolded keystroke transmits.
6 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-3 USB ALT Key Character Set ALT Keys Keystroke 2064 ALT 2 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z
USB Interface 6 - 19 Table 6-4 USB GUI Key Character Set GUI Key Keystroke 3000 Right Control Key 3048 GUI 0 3049 GUI 1 3050 GUI 2 3051 GUI 3 3052 GUI 4 3053 GUI 5 3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on ei
6 - 20 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-4 USB GUI Key Character Set (Continued) GUI Key Keystroke 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.
USB Interface 6 - 21 Table 6-5 USB F Key Character Set F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F10 5011 F11 5012 F12 5013 F13 5014 F14 5015 F15 5016 F16 5017 F17 5018 F18 5019 F19 5020 F20 5021 F21 5022 F22 5023 F23 5024 F24
6 - 22 Symbol DS6708 Digital Scanner Product Reference Guide Table 6-6 USB Numeric Keypad Character Set Numeric Keypad Keystroke 6042 * 6043 + 6044 undefined 6045 - 6046 .
USB Interface 6 - 23 Table 6-7 USB Extended Keypad Character Set Extended Keypad Keystroke 7001 Break 7002 Delete 7003 PgUp 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert 7012 Home 7013 Enter 7014 Escape 7015 Up Arrow 7016 Down Arrow 7017 Left Arrow 7018 Right Arrow
6 - 24 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 7 RS-232 Interface Introduction This chapter describes how to set up the digital scanner with an RS-232 host. Use the RS-232 interface to connect the digital scanner to point-of-sale devices, host computers, or other devices with an available RS-232 port (e.g., com port). If your host does not appear in Table 7-2, refer to the documentation for the host device to set communication parameters to match the host.
7-2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting an RS-232 Interface Connect the digital scanner directly to the host computer. Interface Cable Serial Port Connector to Host Power Supply Cable Figure 7-1 RS-232 Direct Connection Base Serial Port Connector to Host Interface Cable Power Supply Cable Figure 7-2 RS-232 Direct Connection for Scanner with Base NOTE 1. Interface cables vary depending on configuration.
RS-232 Interface 7-3 2. Connect the other end of the RS-232 interface cable to the serial port on the host. 3. Connect the power supply to the serial connector end of the RS-232 interface cable. Plug the power supply into an appropriate outlet. 4. Select the RS-232 host type by scanning the appropriate bar code from RS-232 Host Types on page 7-7. 5. To modify any other parameter options, scan the appropriate bar codes in this chapter.
7-4 Symbol DS6708 Digital Scanner Product Reference Guide RS-232 Parameter Defaults Table 7-1 lists the defaults for RS-232 host parameters. To change any option, scan the appropriate bar code(s) provided in the RS-232 Host Parameters section beginning on page 7-5. NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters.
RS-232 Interface 7-5 RS-232 Host Parameters Various RS-232 hosts use their own parameter default settings. Selecting standard, ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, OPOS/JPOS, Olivetti, or Omron sets the defaults listed in Table 7-2.
7-6 Symbol DS6708 Digital Scanner Product Reference Guide RS-232 Host Parameters (continued) Selecting ICL, Fujitsu, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, OPOS/JPOS, Olivetti, or Omron enables the transmission of code ID characters listed in Table 7-3. These code ID characters are not programmable and are separate from the Transmit Code ID feature. Do not enable the Transmit Code ID feature for these terminals.
RS-232 Interface 7-7 RS-232 Host Types To select an RS-232 host interface, scan one of the following bar codes. Standard RS-2321 ICL RS-232 Wincor-Nixdorf RS-232 Mode A Wincor-Nixdorf RS-232 Mode B Olivetti ORS4500 Omron 1Scanning Standard RS-232 activates the RS-232 driver, but does not change port settings (e.g., parity, data bits, handshaking). Selecting another RS-232 host type bar code changes these settings.
7-8 Symbol DS6708 Digital Scanner Product Reference Guide RS-232 Host Types (continued) OPOS/JPOS Fujitsu RS-232 Baud Rate Baud rate is the number of bits of data transmitted per second. Set the digital scanner's baud rate to match the baud rate setting of the host device. Otherwise, data may not reach the host device or may reach it in distorted form.
RS-232 Interface Baud Rate (continued) *Baud Rate 9600 Baud Rate 19,200 Baud Rate 38,400 Baud Rate 57,600 Baud Rate 115,200 7-9
7 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Parity A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements. • Select Odd parity to set the parity bit value to 0 or 1, based on data, to ensure that the coded character contains an odd number of 1 bits. • Select Even parity to set the parity bit value is set to 0 or 1, based on data, to ensure that the coded character contains an even number of 1 bits.
RS-232 Interface 7 - 11 Stop Bit Select The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. Select the number of stop bits (one or two) based on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements.
7 - 12 Symbol DS6708 Digital Scanner Product Reference Guide Check Receive Errors Select whether or not to check the parity, framing, and overrun of received characters. The parity value of received characters is verified against the parity parameter selected above.
RS-232 Interface 7 - 13 Hardware Handshaking (continued) • None: Scan this bar code to disable hardware handshaking. • Standard RTS/CTS: Scan this bar code to select Standard RTS/CTS Hardware Handshaking. • RTS/CTS Option 1: If you select RTS/CTS Option 1, the digital scanner asserts RTS before transmitting and ignores the state of CTS. The digital scanner de-asserts RTS when the transmission completes. • RTS/CTS Option 2: If you select Option 2, RTS is always high or low (user-programmed logic level).
7 - 14 Symbol DS6708 Digital Scanner Product Reference Guide Software Handshaking This parameter offers control of the data transmission process in addition to, or instead of, that offered by hardware handshaking. There are five options. If software handshaking and hardware handshaking are both enabled, hardware handshaking takes precedence. • None: Select this to transmit data immediately. The scanner expects no response from the host.
RS-232 Interface 7 - 15 Software Handshaking (continued) *None ACK/NAK ENQ ACK/NAK with ENQ XON/XOFF
7 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Host Serial Response Time-out This parameter specifies how long the digital scanner waits for an ACK, NAK, or CTS before determining that a transmission error occurred. This only applies when in one of the ACK/NAK software handshaking modes, or RTS/CTS hardware handshaking mode. *Minimum: 2 Sec Low: 2.5 Sec Medium: 5 Sec High: 7.5 Sec Maximum: 9.
RS-232 Interface 7 - 17 RTS Line State This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to select Low RTS or High RTS line state. *Host: Low RTS Host: High RTS Beep on If you enable this parameter, the digital scanner issues a beep when it detects a character on the RS-232 serial line. indicates an illegal entry or other important event.
7 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Intercharacter Delay This parameter specifies the intercharacter delay inserted between character transmissions.
RS-232 Interface 7 - 19 Nixdorf Beep/LED Options If you selected Nixdorf Mode B, this indicates when the digital scanner beeps and turns on its LED after a decode. *Normal Operation (Beep/LED immediately after decode) Beep/LED After Transmission Beep/LED After CTS Pulse Ignore Unknown Characters Unknown characters are characters the host does not recognize. Select Send Bar Codes with Unknown Characters to send all bar code data except for unknown characters. The digital scanner issues no error beeps.
7 - 20 Symbol DS6708 Digital Scanner Product Reference Guide ASCII Character Set for RS-232 You can assign the values in Table 7-4 as prefixes or suffixes for ASCII character data transmission.
RS-232 Interface 7 - 21 Table 7-4 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1027 %A ESC 1028 %B FS 1029 %C GS 1030 %D RS 1031 %E US 1032 Space Space 1033 /A ! 1034 /B " 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . .
7 - 22 Symbol DS6708 Digital Scanner Product Reference Guide Table 7-4 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S
RS-232 Interface 7 - 23 Table 7-4 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ` 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S
7 - 24 Symbol DS6708 Digital Scanner Product Reference Guide Table 7-4 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1127 Undefined 7013 ENTER
Chapter 8 IBM 468X / 469X Interface Introduction This chapter describes how to set up the digital scanner with an IBM 468X/469X host. Throughout the programming bar code menus, asterisks (*) indicate default values. * Indicates Default NOTE *Disable Convert to Code 39 Feature/Option Most computer monitors allow scanning the bar codes directly on the screen.
8-2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting to an IBM 468X/469X Host Connect the digital scanner directly to the host interface. Interface Cable Host Port Connector Figure 8-1 IBM Direct Connection Interface Cable Host Port Connector Figure 8-2 IBM Direct Connection for Scanner with Base NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 8-1 and Figure 8-2 are examples only.
IBM 468X / 469X Interface IBM Parameter Defaults Table 8-1 lists the defaults for IBM host parameters. To change any option, scan the appropriate bar code(s) provided in the Parameter Descriptions section beginning on page 8-4. NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters.
8-4 Symbol DS6708 Digital Scanner Product Reference Guide IBM 468X/469X Host Parameters Port Address This parameter sets the IBM 468X/469X port used. NOTE Scanning one of these bar codes enables the RS-485 interface on the digital scanner.
IBM 468X / 469X Interface Convert Unknown to Code 39 Scan a bar code below to enable or disable the conversion of unknown bar code type data to Code 39.
8-6 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 9 Wand Emulation Interface Introduction This chapter describes how to set up the digital scanner with a wand emulation host when you need Wand Emulation communication. The digital scanner connects to an external wand decoder or to a decoder integrated in a mobile computer or Point-of-Sale (POS) terminal. In this mode the digital scanner emulates the signal of a digital wand to make it "readable" by a wand decoder. Throughout the programming bar code menus, asterisks (*) indicate default values.
9-2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting Using Wand Emulation To perform Wand Emulation, connect the digital scanner to a mobile computer, or a controller which collects the wand data and interprets it for the host. Mobile Computer Wand Port Interface Cable Figure 9-1 Wand Emulation Connection Mobile Computer Wand Port Interface Cable Figure 9-2 Wand Emulation Connection for Scanner with Base NOTE Interface cables vary depending on configuration.
Wand Emulation Interface 9-3 3. Select the Wand Emulation host type by scanning the appropriate bar code from Wand Emulation Host Types on page 9-5. 4. To modify any other parameter options, scan the appropriate bar codes in this chapter. WARNING! Connect the digital scanner to 5 volt decoders only. Connecting the digital scanner to a 12 volt decoder can damage the digital scanner and invalidate the warranty.
9-4 Symbol DS6708 Digital Scanner Product Reference Guide Wand Emulation Parameter Defaults Table 9-1 lists the defaults for Wand Emulation host types. To change any option, scan the appropriate bar code(s) provided in Wand Emulation Host Parameters on page 9-5. NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters.
Wand Emulation Interface Wand Emulation Host Parameters Wand Emulation Host Types Select a Wand Emulation host by scanning one of the bar codes below.
9-6 Symbol DS6708 Digital Scanner Product Reference Guide Leading Margin (Quiet Zone) Scan a bar code below to select a leading margin duration. A leading margin is the time that precedes the first bar of the scan, in milliseconds. The minimum allowed value is 80 msec and the maximum is 250 msec. This parameter accommodates older wand decoders which cannot handle short leading margins. NOTE 250 msec is the maximum value that this parameter can attain, however, 200 msec is sufficient.
Wand Emulation Interface 9-7 Polarity Polarity determines how the digital scanner's Wand Emulation interface creates the Digitized Barcode Pattern (DBP). DBP is a digital signal that represents the scanned bar code. Different decoders expect the DBP in a certain format. The DBP either has the "highs" represent bars and the "lows" represent spaces (margins), or the "highs" represent spaces (margins) and the "lows" represent bars. Scan the appropriate bar code to select the polarity required by the decoder.
9-8 Symbol DS6708 Digital Scanner Product Reference Guide Convert All Bar Codes to Code 39 By default, the Wand Emulation interface sends data to the attached host in the decoded symbology. This can be a problem for customers with older systems that do not recognize newer symbologies (for example, GS1 DataBar). Enable this parameter to ignore the decoded symbology, and transmit the data as a Code 39 bar code. Lowercase characters in the original data stream transmit as uppercase characters.
Wand Emulation Interface 9-9 Convert Code 39 to Full ASCII By default, a space replaces characters that do not have a corresponding character in the Code 39 symbology set. Enable this parameter to encode data sent to the wand Interface in Code 39 Full ASCII. This setting requires that the host be able to interpret Code 39 Full ASCII data. This setting applies only if you enabled Convert to Code 39.
9 - 10 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 10 Keyboard Wedge Interface Introduction This chapter describes how to set up a Keyboard Wedge interface with the digital scanner. With this interface, the digital scanner is connected between the keyboard and host computer, and translates bar code data into keystrokes. The host computer accepts the keystrokes as if they originated from the keyboard. This mode adds bar code reading functionality to a system designed for manual keyboard input. Keyboard keystrokes are simply passed through.
10 - 2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting a Keyboard Wedge Interface Male DIN Connector Keyboard Connector Female DIN Connector Figure 10-1 Keyboard Wedge Connection with Y-cable Keyboard Connector Female DIN Connector Figure 10-2 Keyboard Wedge Connection with Y-cable for Scanner with Base To connect the Keyboard Wedge interface Y-cable: NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 10-1 and Figure 10-2 are examples only.
Keyboard Wedge Interface 10 - 3 1. Turn off the host and unplug the keyboard connector. 2. Attach the modular connector of the Y-cable to the cable interface port on the digital scanner. See Installing the Interface Cable on page 1-3. 3. Connect the round male DIN host connector of the Y-cable to the keyboard port on the host device. 4. Connect the round female DIN keyboard connector of the Y-cable to the keyboard connector. 5.
10 - 4 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-1 Keyboard Wedge Host Default Table (Continued) Parameter Default Page Number Function Key Mapping Disable 10-11 FN1 Substitution Disable 10-12 Send and Make Break Send 10-12
Keyboard Wedge Interface 10 - 5 Keyboard Wedge Host Parameters Keyboard Wedge Host Types Select the Keyboard Wedge host by scanning one of the bar codes below.
10 - 6 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Wedge Country Types - Country Codes Scan the bar code corresponding to the keyboard type. If your keyboard type does not appear, see Alternate Numeric Keypad Emulation on page 10-9.
Keyboard Wedge Interface 10 - 7 Keyboard Wedge Country Types - Country Codes (continued) Italian Windows Swedish Windows UK English Windows Japanese Windows Portuguese-Brazilian Windows
10 - 8 Symbol DS6708 Digital Scanner Product Reference Guide Ignore Unknown Characters Unknown characters are characters the host does not recognize. Select Send Bar Codes With Unknown Characters to send all bar code data except for unknown characters. The digital scanner issues no error beeps. Select Do Not Send Bar Codes With Unknown Characters to send bar code data up to the first unknown character. The digital scanner issues an error beep.
Keyboard Wedge Interface 10 - 9 Intra-Keystroke Delay Enable this to insert an additional delay between each emulated key depression and release. This sets the Keystroke Delay parameter to a minimum of 5 msec as well. Enable *Disable Alternate Numeric Keypad Emulation This allows emulation of most other country keyboard types not listed in Keyboard Wedge Country Types - Country Codes on page 10-6 in a Microsoft® operating system environment.
10 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Caps Lock On Enable this to emulate keystrokes as if the Caps Lock key is always pressed. Enable Caps Lock On *Disable Caps Lock On Caps Lock Override If you enable this, on AT or AT Notebook hosts, the keyboard ignores the state of the Caps Lock key. Therefore, an ‘A’ in the bar code transmits as an ‘A’ regardless of the state of the keyboard’s Caps Lock key.
Keyboard Wedge Interface 10 - 11 Convert Wedge Data Enable this to convert all bar code data to the selected case. Convert to Upper Case Convert to Lower Case *No Convert Function Key Mapping ASCII values under 32 are normally sent as control key sequences (see Table 10-2 on page 10-15). Enable this parameter to send the keys in bold in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not you enable this parameter.
10 - 12 Symbol DS6708 Digital Scanner Product Reference Guide FN1 Substitution Enable this to replace FN1 characters in a GS1 128 bar code with a user-selected keystroke (see FN1 Substitution on page 10-12). Enable *Disable Send Make and Break Enable this to prevent sending the scan codes for releasing a key.
Keyboard Wedge Interface 10 - 13 Keyboard Maps Refer to the following keyboard maps for prefix/suffix keystroke parameters. To program the prefix/suffix values, see the bar codes on page 4-17.
10 - 14 Symbol DS6708 Digital Scanner Product Reference Guide 1065 1066 1067 1068 1072 1073 1074 1079 1080 1081 5001 5002 5011 5003 1069 1070 1071 1075 1076 1077 1078 1082 1083 1084 1085 1045 5013 1086 5004 5014 5015 1087 5005 5006 1043 5016 1088 5007 5008 5017 5018 1089 5009 5010 7013 5019 1090 1048 5012 (1048 if double key) Figure 10-6 NCR 7052 58-Key 1046 (1043 if double key)
Keyboard Wedge Interface 10 - 15 ASCII Character Set for Keyboard Wedge NOTE Code 39 Full ASCII interprets the bar code special character ($ + % /) preceding a Code 39 character and assigns an ASCII character value to the pair. For example, if you enable Code 39 Full ASCII and scan +B, it transmits as b, %J as ?, and %V as @. Scanning ABC%I outputs the keystroke equivalent of ABC >. Table 10-2 Keyboard Wedge ASCII Character Set Full ASCII Code 39 Encode Char.
10 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-2 Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Char.
Keyboard Wedge Interface 10 - 17 Table 10-2 Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Char.
10 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-2 Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Char.
Keyboard Wedge Interface 10 - 19 Table 10-2 Keyboard Wedge ASCII Character Set (Continued) ASCII Value Full ASCII Code 39 Encode Char.acter Keystroke 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1 The keystroke in bold transmits only if you enabled Function Key Mapping on page 10-11.
10 - 20 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-3 Keyboard Wedge ALT Key Character Set (Continued) ALT Keys Keystroke 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z Table 10-4 Keyboard Wedge GUI Key Character Set GUI Keys Keystrokes 3000 Right Control Key 3048 GUI 0 3049 GUI 1
Keyboard Wedge Interface 10 - 21 Table 10-4 Keyboard Wedge GUI Key Character Set (Continued) GUI Keys Keystrokes 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z
10 - 22 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-5 Keyboard Wedge F Key Character Set F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F10 5011 F11 5012 F12 5013 F13 5014 F14 5015 F15 5016 F16 5017 F17 5018 F18 5019 F19 5020 F20 5021 F21 5022 F22 5023 F23 5024 F24 Table 10-6 Keyboard Wedge Numeric Keypad Character Set Numeric Keypad Keystroke 6042 * 6043 + 6044 undefined 6045 -
Keyboard Wedge Interface 10 - 23 Table 10-6 Keyboard Wedge Numeric Keypad Character Set (Continued) Numeric Keypad Keystroke 6046 .
10 - 24 Symbol DS6708 Digital Scanner Product Reference Guide Table 10-7 Keyboard Wedge Extended Keypad Character Set (Continued) Extended Keypad Keystroke 7015 Up Arrow 7016 Dn Arrow 7017 Left Arrow 7018 Right Arrow
Chapter 11 Scanner Emulation Interface Introduction This chapter describes how to set up the digital scanner with a Scanner Emulation host. In this mode, the digital scanner connects to an external decoder or to a decoder integrated in a mobile computer or Point-of-Sale (POS) terminal. Throughout the programming bar code menus, asterisks (*) indicate default values.
11 - 2 Symbol DS6708 Digital Scanner Product Reference Guide Connecting Using Scanner Emulation To perform Scanner Emulation, connect the digital scanner to a mobile computer, or a controller which collects the data and interprets it for the host. Host Port Connector Interface Cable Figure 11-1 Scanner Emulation Connection Host Port Connector Interface Cable Figure 11-2 Scanner Emulation Connection for Scanner with Base NOTE Interface cables vary depending on configuration.
Scanner Emulation Interface 11 - 3 3. Scan the Scanner Emulation Host bar code from Scanner Emulation Host on page 11-5 to enable the Scanner Emulation host interface. 4. To modify any other parameter options, scan the appropriate bar codes in this chapter. WARNING! Connect the digital scanner to 5 volt decoders only. Connecting the digital scanner to a 12 volt decoder can damage the digital scanner and invalidate the warranty.
11 - 4 Symbol DS6708 Digital Scanner Product Reference Guide Scanner Emulation Parameter Defaults Table 11-1 lists the defaults for the Scanner Emulation host. To change any option, scan the appropriate bar code(s) provided in the Scanner Emulation Host Parameters section beginning on page 11-5. NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters.
Scanner Emulation Interface 11 - 5 Scanner Emulation Host Scan the bar code below to enable the Scanner Emulation host. Scanner Emulation Host Scanner Emulation Host Parameters Beep Style The Scanner Emulation host supports three beep styles. • Beep On Successful Transmit: The digital scanner beeps when the attached decoder issues the decode signal to the digital scanner, so the digital scanner and the attached decoder beep at the same time. • Beep At Decode Time: The digital scanner beeps upon decode.
11 - 6 Symbol DS6708 Digital Scanner Product Reference Guide Parameter Pass-Through The Scanner Emulation host can process parameter bar code messages and send them to the attached decoder. In this way, customers using Symbol compliant decoders can control the behavior of the entire system by scanning the necessary parameters only once. For example, to enable D 2 of 5, scan the D 2 of 5 Enable parameter bar code. The digital scanner and the attached decoder both process the parameter.
Scanner Emulation Interface 11 - 7 Convert Newer Code Types The digital scanner supports a variety of code types that are not decodable by attached decoder systems. To allow compatibility in these environments, the digital scanner converts these code types to more commonly decodable symbologies, as per the following chart. Symbologies not listed on this chart transmit normally.
11 - 8 Symbol DS6708 Digital Scanner Product Reference Guide Convert All Bar Codes to Code 39 Scan a bar code below to enable or disable converting all bar code data to Code 39. *Do Not Convert Bar Codes To Code 39 Convert All To Code 39 Code 39 Full ASCII Conversion By default, a space replaces any characters that do not have a corresponding character in the Code 39 symbology set. Enable this parameter to encode data sent to the Scanner Emulation host in Code 39 Full ASCII.
Scanner Emulation Interface 11 - 9 Transmission Timeout The Scanner Emulation host transmits bar code data to the attached decoder and waits for the decoder to assert the Decode signal, indicating successful transmission. If, after a specified amount of time, the Decode signal is not asserted (indicating that the attached decoder did not successfully receive the bar code data), the digital scanner issues transmit error beeps. Scan the appropriate bar code below to select the desired transmission timeout.
11 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Ignore Unknown Characters Unknown characters are characters the decoder does not recognize. Select Ignore Unknown Characters to send all bar code data except for unknown characters. The digital scanner issues no error beeps. Select Convert Error on Unknown Characters to prevent sending bar codes containing at least one unknown character to the decoder. The digital scanner issues a convert error beep.
Scanner Emulation Interface 11 - 11 Leading Margin (continued) 5 ms Leading Margin 10 ms Leading Margin Check For Decode LED The attached decoder normally asserts the Decode line to signal to the Scanner Emulation host to indicate that it successfully decoded the transmitted bar code. Some decoders, however, do not assert the Decode signal. In this case, the digital scanner emits transmit error beeps to indicate that the bar code did not successfully transmit.
11 - 12 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 12 123Scan Introduction 123Scan is a Windows®-based utility that programs the digital scanner with all parameters including Advanced Data Formatting (ADF) rules. An ADF rule modifies bar code data before it transmits to the host to ensure compatibility between bar coded data and the host application. You can program digital scanners via PC download or by scanning a sheet of bar codes generated by the 123Scan utility. Digital scanner programming is saved in a file for electronic distribution.
12 - 2 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 13 Symbologies Introduction This chapter describes symbology features and provides programming bar codes for selecting these features. Before programming, follow the instructions in Chapter 1, Getting Started. To set feature values, scan a single bar code or a short bar code sequence. The settings are stored in non-volatile memory and are preserved even when the digital scanner powers down. NOTE Most computer monitors allow scanning the bar codes directly on the screen.
13 - 2 Symbol DS6708 Digital Scanner Product Reference Guide Errors While Scanning Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter. Symbology Parameter Defaults Table 13-1 lists the defaults for all symbologies parameters. There are two ways to change the default values: • Scan the appropriate bar codes in this guide. These new values replace the standard default values in memory.
Symbologies 13 - 3 Table 13-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Convert UPC-E1 to A 26h Disable 13-19 EAN-8/JAN-8 Extend 27h Disable 13-20 Bookland ISBN Format F1h 40h ISBN-10 13-21 UCC Coupon Extended Code 55h Disable 13-22 ISSN EAN F1h 69h Disable 13-22 Code 128 08h Enable 13-23 Set Length(s) for Code 128 D1h D2h Any Length 13-23 GS1-128 (formerly UCC/EAN-128) 0Eh Enable 13-25 ISBT 128 54h Enable 13-25 ISBT Concatenation
13 - 4 Symbol DS6708 Digital Scanner Product Reference Guide Table 13-1 Parameter Defaults (Continued) Parameter Transmit Code 11 Check Digit(s) Parameter Number Default Page Number 2Fh Disable 13-41 Interleaved 2 of 5 (ITF) 06h Enable 13-41 Set Lengths for I 2 of 5 16h 17h 14 13-42 I 2 of 5 Check Digit Verification 31h Disable 13-44 Transmit I 2 of 5 Check Digit 2Ch Disable 13-44 Convert I 2 of 5 to EAN 13 52h Disable 13-45 Discrete 2 of 5 05h Disable 13-45 Set Length(s) fo
Symbologies 13 - 5 Table 13-1 Parameter Defaults (Continued) Parameter Inverse 1D Parameter Number Default Page Number F1h 4Ah Regular 13-59 US Postnet 59h Enable 13-60 US Planet 5Ah Enable 13-60 Transmit US Postal Check Digit 5Fh Enable 13-61 UK Postal 5Bh Enable 13-61 Transmit UK Postal Check Digit 60h Enable 13-62 Japan Postal F0h 22h Enable 13-62 Australian Postal F0h 23h Enable 13-63 Netherlands KIX Code F0h 46h Enable 13-63 USPS 4CB/One Code/Intelligent Mail F
13 - 6 Symbol DS6708 Digital Scanner Product Reference Guide Table 13-1 Parameter Defaults (Continued) Parameter Parameter Number Default Page Number Data Matrix F0h 24h Enable 13-72 Data Matrix Inverse F1h 4Ch Regular 13-72 Maxicode F0h 26h Enable 13-73 QR Code F0h 25h Enable 13-74 QR Inverse F1h 4Bh Regular 13-74 MicroQR F1h 3Dh Enable 13-75 Aztec F1h 3Eh Enable 13-75 Aztec Inverse F1h 4Dh Regular 13-76 Redundancy Level 4Eh 1 13-77 Security Level 4Dh 1 13-79 I
Symbologies 13 - 7 UPC/EAN Enable/Disable UPC-A Parameter # 01h To enable or disable UPC-A, scan the appropriate bar code below. *Enable UPC-A (01h) Disable UPC-A (00h) Enable/Disable UPC-E Parameter # 02h To enable or disable UPC-E, scan the appropriate bar code below.
13 - 8 Symbol DS6708 Digital Scanner Product Reference Guide Enable/Disable UPC-E1 Parameter # 0Ch UPC-E1 is disabled by default. To enable or disable UPC-E1, scan the appropriate bar code below. NOTE UPC-E1 is not a UCC (Uniform Code Council) approved symbology. Enable UPC-E1 (01h) *Disable UPC-E1 (00h) Enable/Disable EAN-8/JAN-8 Parameter # 04h To enable or disable EAN-8/JAN-8, scan the appropriate bar code below.
Symbologies 13 - 9 Enable/Disable EAN-13/JAN-13 Parameter # 03h To enable or disable EAN-13/JAN-13, scan the appropriate bar code below. *Enable EAN-13/JAN-13 (01h) Disable EAN-13/JAN-13 (00h) Enable/Disable Bookland EAN Parameter # 53h To enable or disable Bookland EAN, scan the appropriate bar code below. Enable Bookland EAN (01h) *Disable Bookland EAN (00h) NOTE If you enable Bookland EAN, select a Bookland ISBN Format on page 13-21.
13 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Decode UPC/EAN/JAN Supplementals Parameter # 10h Supplementals are bar codes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2). The following options are available: • If you select Ignore UPC/EAN with Supplementals, and the scanner is presented with a UPC/EAN plus supplemental symbol, the scanner decodes UPC/EAN and ignores the supplemental characters.
Symbologies 13 - 11 Decode UPC/EAN/JAN Supplementals (continued) Decode UPC/EAN/JAN Only With Supplementals (01h) *Ignore Supplementals (00h) Autodiscriminate UPC/EAN/JAN Supplementals (02h) Enable 378/379 Supplemental Mode (04h) Enable 978/979 Supplemental Mode (05h) Enable 977 Supplemental Mode (07h)
13 - 12 Symbol DS6708 Digital Scanner Product Reference Guide Decode UPC/EAN/JAN Supplementals (continued) Enable 414/419/434/439 Supplemental Mode (06h) Enable 491 Supplemental Mode (08h) Enable Smart Supplemental Mode (03h) Supplemental User-Programmable Type 1 (09h) Supplemental User-Programmable Type 1 and 2 (0Ah) Smart Supplemental Plus User-Programmable 1 (0Bh) Smart Supplemental Plus User-Programmable 1 and 2 (0Ch)
Symbologies 13 - 13 User-Programmable Supplementals Supplemental 1: Parameter # F1h 43h Supplemental 2: Parameter # F1h 44h If you selected a Supplemental User-Programmable option from Decode UPC/EAN/JAN Supplementals on page 13-10, select User-Programmable Supplemental 1 to set the 3-digit prefix. Then select the 3 digits using the numeric bar codes beginning on page D-1. Select User-Programmable Supplemental 2 to set a second 3-digit prefix.
13 - 14 Symbol DS6708 Digital Scanner Product Reference Guide Transmit UPC-A Check Digit Parameter # 28h The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-A check digit. It is always verified to guarantee the integrity of the data.
Symbologies 13 - 15 Transmit UPC-E1 Check Digit Parameter # 2Ah The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPC-E1 check digit. It is always verified to guarantee the integrity of the data.
13 - 16 Symbol DS6708 Digital Scanner Product Reference Guide UPC-A Preamble Parameter # 22h Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-A preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
Symbologies 13 - 17 UPC-E Preamble Parameter # 23h Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
13 - 18 Symbol DS6708 Digital Scanner Product Reference Guide UPC-E1 Preamble Parameter # 24h Preamble characters are part of the UPC symbol, and include Country Code and System Character. There are three options for transmitting a UPC-E1 preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and transmit no preamble. Select the appropriate option to match the host system.
Symbologies 13 - 19 Convert UPC-E to UPC-A Parameter # 25h Enable this to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). Disable this to transmit UPC-E decoded data as UPC-E data, without conversion.
13 - 20 Symbol DS6708 Digital Scanner Product Reference Guide EAN-8/JAN-8 Extend Parameter # 27h Enable this parameter to add five leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols. Disable this to transmit EAN-8 symbols as is.
Symbologies 13 - 21 Bookland ISBN Format Parameter # F1h 40h If you enabled Bookland EAN using Enable/Disable Bookland EAN on page 13-9, select one of the following formats for Bookland data: • Bookland ISBN-10 - The scanner reports Bookland data starting with 978 in traditional 10-digit format with the special Bookland check digit for backward-compatibility. Data starting with 979 is not considered Bookland in this mode.
13 - 22 Symbol DS6708 Digital Scanner Product Reference Guide UCC Coupon Extended Code Parameter # 55h Enable this parameter to decode UPC-A bar codes starting with digit ‘5’, EAN-13 bar codes starting with digit ‘99’, and UPC-A/GS1-128 Coupon Codes. UPCA, EAN-13, and GS1-128 must be enabled to scan all types of Coupon Codes.
Symbologies 13 - 23 Code 128 Enable/Disable Code 128 Parameter # 08h To enable or disable Code 128, scan the appropriate bar code below. *Enable Code 128 (01h) Disable Code 128 (00h) Set Lengths for Code 128 Parameter # L1 = D1h, L2 = D2h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 128 to any length, one or two discrete lengths, or lengths within a specific range.
13 - 24 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for Code 128 (continued) Code 128 - One Discrete Length Code 128 - Two Discrete Lengths Code 128 - Length Within Range *Code 128 - Any Length
Symbologies 13 - 25 Enable/Disable GS1-128 (formerly UCC/EAN-128) Parameter # 0Eh To enable or disable GS1-128, scan the appropriate bar code below. *Enable GS1-128 (01h) Disable GS1-128 (00h) Enable/Disable ISBT 128 Parameter # 54h ISBT 128 is a variant of Code 128 used in the blood bank industry. Scan a bar code below to enable or disable ISBT 128. If necessary, the host must perform concatenation of the ISBT data.
13 - 26 Symbol DS6708 Digital Scanner Product Reference Guide ISBT Concatenation Parameter # F1h 41h Select an option for concatenating pairs of ISBT code types: • If you select Disable ISBT Concatenation, the digital scanner does not concatenate pairs of ISBT codes it encounters. • If you select Enable ISBT Concatenation, there must be two ISBT codes in order for the digital scanner to decode and perform concatenation. The digital scanner does not decode single ISBT symbols.
Symbologies 13 - 27 Check ISBT Table Parameter # F1h 42h The ISBT specification includes a table that lists several types of ISBT bar codes that are commonly used in pairs. If you set ISBT Concatenation to Enable, enable Check ISBT Table to concatenate only those pairs found in this table. Other types of ISBT codes are not concatenated.
13 - 28 Symbol DS6708 Digital Scanner Product Reference Guide Code 39 Enable/Disable Code 39 Parameter # 00h To enable or disable Code 39, scan the appropriate bar code below. *Enable Code 39 (01h) Disable Code 39 (00h) Enable/Disable Trioptic Code 39 Parameter # 0Dh Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges. Trioptic Code 39 symbols always contain six characters. To enable or disable Trioptic Code 39, scan the appropriate bar code below.
Symbologies 13 - 29 Convert Code 39 to Code 32 Parameter # 56h Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable or disable converting Code 39 to Code 32. NOTE Code 39 must be enabled for this parameter to function.
13 - 30 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for Code 39 Parameter # L1 = 12h, L2 = 13h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 39 to any length, one or two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled, Length Within a Range or Any Length are the preferred options.
Symbologies 13 - 31 Set Lengths for Code 39 (continued) Code 39 - One Discrete Length Code 39 - Two Discrete Lengths Code 39 - Length Within Range Code 39 - Any Length
13 - 32 Symbol DS6708 Digital Scanner Product Reference Guide Code 39 Check Digit Verification Parameter # 30h Enable this feature to check the integrity of all Code 39 symbols to verify that the data complies with specified check digit algorithm. Only Code 39 symbols which include a modulo 43 check digit are decoded. Enable this feature if the Code 39 symbols contain a Modulo 43 check digit.
Symbologies 13 - 33 Code 39 Full ASCII Conversion Parameter # 11h Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar code below. Enable Code 39 Full ASCII (01h) *Disable Code 39 Full ASCII (00h) NOTE You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously.
13 - 34 Symbol DS6708 Digital Scanner Product Reference Guide Code 39 Buffering - Scan & Store (continued) This feature affects Code 39 only. If selecting Buffer Code 39, we recommend configuring the digital scanner to decode Code 39 symbology only. Buffer Code 39 (Enable) (01h) *Do Not Buffer Code 39 (Disable) (00h) While there is data in the transmission buffer, you cannot select Do Not Buffer Code 39. The buffer holds 200 bytes of information.
Symbologies 13 - 35 Transmit Buffer There are two methods to transmit the Code 39 buffer. 1. Scan the Transmit Buffer bar code below, which includes only a start character, a plus (+), and a stop character. 2. The digital scanner transmits and clears the buffer. • The digital scanner issues a low/high beep. Transmit Buffer 3. Scan a Code 39 bar code with a leading character other than a space. • The digital scanner appends new decode data to buffered data.
13 - 36 Symbol DS6708 Digital Scanner Product Reference Guide Code 93 Enable/Disable Code 93 Parameter # 09h To enable or disable Code 93, scan the appropriate bar code below. Enable Code 93 (01h) *Disable Code 93 (00h) Set Lengths for Code 93 Parameter # L1 = 1Ah, L2 = 1Bh The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains.
Symbologies 13 - 37 Set Lengths for Code 93 (continued) Code 93 - One Discrete Length Code 93 - Two Discrete Lengths Code 93 - Length Within Range Code 93 - Any Length
13 - 38 Symbol DS6708 Digital Scanner Product Reference Guide Code 11 Code 11 Parameter # 0Ah To enable or disable Code 11, scan the appropriate bar code below. Enable Code 11 (01h) *Disable Code 11 (00h) Set Lengths for Code 11 Parameter # L1 = 1Ch, L2 = 1Dh The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specific range.
Symbologies 13 - 39 Set Lengths for Code 11 (continued) Code 11 - One Discrete Length Code 11 - Two Discrete Lengths Code 11 - Length Within Range Code 11 - Any Length
13 - 40 Symbol DS6708 Digital Scanner Product Reference Guide Code 11 Check Digit Verification Parameter # 34h This feature allows the digital scanner to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit algorithm. This selects the check digit mechanism for the decoded Code 11 bar code. The options are to check for one check digit, check for two check digits, or disable the feature.
Symbologies 13 - 41 Transmit Code 11 Check Digits Parameter # 2Fh This feature selects whether or not to transmit the Code 11 check digit(s). Transmit Code 11 Check Digit(s) (Enable) (01h) *Do Not Transmit Code 11 Check Digit(s) (Disable) (00h) NOTE Code 11 Check Digit Verification must be enabled for this parameter to function.
13 - 42 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for Interleaved 2 of 5 Parameter # L1 = 16h, L2 = 17h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for I 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range. • One Discrete Length - Select this option to decode only I 2 of 5 symbols containing a selected length.
Symbologies 13 - 43 Set Lengths for Code 11 (continued) I 2 of 5 - One Discrete Length I 2 of 5 - Two Discrete Lengths I 2 of 5 - Length Within Range I 2 of 5 - Any Length
13 - 44 Symbol DS6708 Digital Scanner Product Reference Guide I 2 of 5 Check Digit Verification Parameter # 31h Enable this feature to check the integrity of all I 2 of 5 symbols to verify the data complies with either the specified Uniform Symbology Specification (USS), or the Optical Product Code Council (OPCC) check digit algorithm.
Symbologies 13 - 45 Convert I 2 of 5 to EAN-13 Parameter # 52h Enable this parameter to convert 14-character I 2 of 5 codes to EAN-13, and transmit to the host as EAN-13. To accomplish this, the I 2 of 5 code must be enabled, and the code must have a leading zero and a valid EAN-13 check digit.
13 - 46 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for Discrete 2 of 5 Parameter # L1 = 14h, L2 = 15h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for D 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range. • One Discrete Length - Select this option to decode only D 2 of 5 symbols containing a selected length.
Symbologies 13 - 47 Set Lengths for Discrete 2 of 5 (continued) D 2 of 5 - One Discrete Length D 2 of 5 - Two Discrete Lengths D 2 of 5 - Length Within Range D 2 of 5 - Any Length
13 - 48 Symbol DS6708 Digital Scanner Product Reference Guide Codabar (NW - 7) Enable/Disable Codabar Parameter # 07h To enable or disable Codabar, scan the appropriate bar code below. Enable Codabar (01h) *Disable Codabar (00h) Set Lengths for Codabar Parameter # L1 = 18h, L2 = 19h The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains.
Symbologies 13 - 49 Set Lengths for Codabar (continued) Codabar - One Discrete Length Codabar - Two Discrete Lengths Codabar - Length Within Range Codabar - Any Length
13 - 50 Symbol DS6708 Digital Scanner Product Reference Guide CLSI Editing Parameter # 36h Enable this parameter to strip the start and stop characters and insert a space after the first, fifth, and tenth characters of a 14-character Codabar symbol. Enable this feature if the host system requires this data format. Symbol length does not include start and stop characters.
Symbologies 13 - 51 MSI Enable/Disable MSI Parameter # 0Bh To enable or disable MSI, scan the appropriate bar code below. Enable MSI (01h) *Disable MSI (00h) Set Lengths for MSI Parameter # L1 = 1Eh, L2 = 1Fh The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for MSI to any length, one or two discrete lengths, or lengths within a specific range.
13 - 52 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for MSI (continued) NOTE Due to the construction of the MSI symbology, it is possible for a scan line covering only a portion of the code to transmit as a complete scan, yielding less data than is encoded in the bar code. To prevent this, select specific lengths (MSI - One Discrete Length, Two Discrete Lengths) for MSI applications.
Symbologies 13 - 53 MSI Check Digits Parameter # 32h With MSI symbols, one check digit is mandatory and always verified by the reader. The second check digit is optional. If the MSI codes include two check digits, scan the Two MSI Check Digits bar code to enable verification of the second check digit. See MSI Check Digit Algorithm on page 13-54 for the selection of second digit algorithms.
13 - 54 Symbol DS6708 Digital Scanner Product Reference Guide MSI Check Digit Algorithm Parameter # 33h Two algorithms are possible for the verification of the second MSI check digit. Select the bar code below corresponding to the algorithm used to encode the check digit. MOD 10/MOD 11 (00h) *MOD 10/MOD 10 (01h) Chinese 2 of 5 Enable/Disable Chinese 2 of 5 Parameter # F0h 98h To enable or disable Chinese 2 of 5, scan the appropriate bar code below.
Symbologies 13 - 55 Matrix 2 of 5 Enable/Disable Matrix 2 of 5 Parameter # F1h 6Ah To enable or disable Matrix 2 of 5, scan the appropriate bar code below.
13 - 56 Symbol DS6708 Digital Scanner Product Reference Guide Set Lengths for Matrix 2 of 5 Parameter # L1 = F1h 6Bh, L2 = F1h 6Ch The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for Matrix 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range. • One Discrete Length - Select this option to decode only Matrix 2 of 5 symbols containing a selected length.
Symbologies 13 - 57 Matrix 2 of 5 Redundancy Parameter # F1h 6Dh To enable or disable Matrix 2 of 5 redundancy, scan the appropriate bar code below. Enable Matrix 2 of 5 Redundancy (01h) *Disable Matrix 2 of 5 Redundancy (00h) Matrix 2 of 5 Check Digit Parameter # F1h 6Eh The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the Matrix 2 of 5 check digit.
13 - 58 Symbol DS6708 Digital Scanner Product Reference Guide Transmit Matrix 2 of 5 Check Digit Parameter # F1h 6Fh Scan a bar code below to transmit Matrix 2 of 5 data with or without the check digit.
Symbologies 13 - 59 Inverse 1D Parameter # F1h 4Ah This parameter sets the 1D inverse decoder setting. Options are: • Regular Only - the scanner decodes regular 1D bar codes only. • Inverse Only - the scanner decodes inverse 1D bar codes only. • Inverse Autodetect - the scanner decodes both regular and inverse 1D bar codes.
13 - 60 Symbol DS6708 Digital Scanner Product Reference Guide Postal Codes US Postnet Parameter # 59h To enable or disable US Postnet, scan the appropriate bar code below. *Enable US Postnet (01h) Disable US Postnet (00h) US Planet Parameter # 5Ah To enable or disable US Planet, scan the appropriate bar code below.
Symbologies 13 - 61 Transmit US Postal Check Digit Parameter # 5Fh Select whether to transmit US Postal data, which includes both US Postnet and US Planet, with or without the check digit. *Transmit US Postal Check Digit (01h) Do Not Transmit US Postal Check Digit (00h) UK Postal Parameter # 5Bh To enable or disable UK Postal, scan the appropriate bar code below.
13 - 62 Symbol DS6708 Digital Scanner Product Reference Guide Transmit UK Postal Check Digit Parameter # 60h Select whether to transmit UK Postal data with or without the check digit. *Transmit UK Postal Check Digit (01h) Do Not Transmit UK Postal Check Digit (00h) Japan Postal Parameter # F0h, 22h To enable or disable Japan Postal, scan the appropriate bar code below.
Symbologies 13 - 63 Australian Postal Parameter # F0h, 23h To enable or disable Australian Postal, scan the appropriate bar code below. *Enable Australian Postal (01h) Disable Australian Postal (00h) Netherlands KIX Code Parameter # F0h, 46h To enable or disable Netherlands KIX Code, scan the appropriate bar code below.
13 - 64 Symbol DS6708 Digital Scanner Product Reference Guide USPS 4CB/One Code/Intelligent Mail Parameter # F1h 50h To enable or disable USPS 4CB/One Code/Intelligent Mail, scan the appropriate bar code below. Enable USPS 4CB/One Code/Intelligent Mail (01h) *Disable USPS 4CB/One Code/Intelligent Mail (00h) UPU FICS Postal Parameter # F1h 63h To enable or disable UPU FICS Postal, scan the appropriate bar code below.
Symbologies 13 - 65 GS1 DataBar (formerly Reduced Space Symbology) The variants of GS1 DataBar are DataBar-14, DataBar Expanded, and DataBar Limited. The limited and expanded versions have stacked variants. Scan the appropriate bar codes to enable or disable each variant of GS1 DataBar. GS1 DataBar-14 Parameter # F0h 52h. *Enable GS1 DataBar-14 (01h) Disable GS1 DataBar 14 (00h) GS1 DataBar Limited Parameter # F0h 53h.
13 - 66 Symbol DS6708 Digital Scanner Product Reference Guide GS1 DataBar Expanded Parameter # F0h 54h. *Enable GS1 DataBar Expanded (01h) Disable GS1 DataBar Expanded (00h) Convert GS1 DataBar to UPC/EAN Parameter # F0h, 8Dh This parameter only applies to GS1 DataBar-14 and GS1 DataBar Limited symbols not decoded as part of a Composite symbol. Enable this to strip the leading '010' from DataBar-14 and DataBar Limited symbols encoding a single zero as the first digit, and report the bar code as EAN-13.
Symbologies 13 - 67 Composite Composite CC-C Parameter # F0h 55h Scan a bar code below to enable or disable Composite bar codes of type CC-C. Enable CC-C (01h) *Disable CC-C (00h) Composite CC-A/B Parameter # F0h 56h Scan a bar code below to enable or disable Composite bar codes of type CC-A/B.
13 - 68 Symbol DS6708 Digital Scanner Product Reference Guide Composite TLC-39 Parameter # F0h 73h Scan a bar code below to enable or disable Composite bar codes of type TLC-39. Enable TLC39 (01h) *Disable TLC39 (00h) UPC Composite Mode Parameter # F0h 58h Select an option for linking UPC symbols with a 2D symbol during transmission as if they were one symbol: • Select UPC Never Linked to transmit UPC bar codes regardless of whether a 2D symbol is detected.
Symbologies 13 - 69 Composite Beep Mode Parameter # F0h, 8Eh To select the number of decode beeps when a composite bar code is decoded, scan the appropriate bar code. Single Beep after both are decoded (00h) *Beep as each code type is decoded (01h) Double Beep after both are decoded (02h) GS1-128 Emulation Mode for GS1 Composite Codes (formerly UCC/EAN Code 128 Emulation Mode for UCC/EAN Composite Codes) Parameter # F0h, ABh Select whether to enable or disable this mode.
13 - 70 Symbol DS6708 Digital Scanner Product Reference Guide 2D Symbologies Enable/Disable PDF417 Parameter # 0Fh To enable or disable PDF417, scan the appropriate bar code below. *Enable PDF417 (01h) Disable PDF417 (00h) Enable/Disable MicroPDF417 Parameter # E3h To enable or disable MicroPDF417, scan the appropriate bar code below.
Symbologies 13 - 71 Code 128 Emulation Parameter # 7Bh Enable this parameter to transmit data from certain MicroPDF417 symbols as Code 128. AIM Code ID Character (01h) on page 4-16 must be enabled for this parameter to work.
13 - 72 Symbol DS6708 Digital Scanner Product Reference Guide Data Matrix Parameter # F0h, 24h To enable or disable Data Matrix, scan the appropriate bar code below. *Enable Data Matrix (01h) Disable Data Matrix (00h) Data Matrix Inverse Parameter # F1h 4Ch This parameter sets the Data Matrix inverse decoder setting. Options are: • Regular Only - the scanner decodes regular Data Matrix bar codes only. • Inverse Only - the scanner decodes inverse Data Matrix bar codes only.
Symbologies 13 - 73 Maxicode Parameter # F0h, 26h To enable or disable Maxicode, scan the appropriate bar code below.
13 - 74 Symbol DS6708 Digital Scanner Product Reference Guide QR Code Parameter # F0h,25h To enable or disable QR Code, scan the appropriate bar code below. *Enable QR Code (01h) Disable QR Code (00h) QR Inverse Parameter # F1h 4Bh This parameter sets the QR inverse decoder setting. Options are: • Regular Only - the scanner decodes regular QR bar codes only. • Inverse Only - the scanner decodes inverse QR bar codes only. • Inverse Autodetect - the scanner decodes both regular and inverse QR bar codes.
Symbologies 13 - 75 MicroQR Parameter # F1h 3Dh To enable or disable MicroQR, scan the appropriate bar code below. *Enable MicroQR (01h) Disable MicroQR (00h) Aztec Parameter # F1h 3Eh To enable or disable Aztec, scan the appropriate bar code below.
13 - 76 Symbol DS6708 Digital Scanner Product Reference Guide Aztec Inverse Parameter # F1h 4Dh This parameter sets the Aztec inverse decoder setting. Options are: • Regular Only - the scanner decodes regular Aztec bar codes only. • Inverse Only - the scanner decodes inverse Aztec bar codes only. • Inverse Autodetect - the scanner decodes both regular and inverse Aztec bar codes.
Symbologies 13 - 77 Redundancy Level Parameter # 4Eh The digital scanner offers four levels of decode redundancy. Select higher redundancy levels for decreasing levels of bar code quality. As redundancy levels increase, the digital scanner’s aggressiveness decreases. Select the redundancy level appropriate for the bar code quality.
13 - 78 Symbol DS6708 Digital Scanner Product Reference Guide Redundancy Level 4 The following code types must be successfully read three times before being decoded: Table 13-5 Redundancy Level 4 Codes Code Type Code Length All All *Redundancy Level 1 (01h) Redundancy Level 2 (02h) Redundancy Level 3 (03h) Redundancy Level 4 (04h)
Symbologies 13 - 79 Security Level Parameter # 4Dh The digital scanner offers four levels of decode security for delta bar codes, which include the Code 128 family, UPC/EAN, and Code 93. Select increasing levels of security for decreasing levels of bar code quality. There is an inverse relationship between security and digital scanner aggressiveness, so choose only that level of security necessary for any given application.
13 - 80 Symbol DS6708 Digital Scanner Product Reference Guide Intercharacter Gap Size Parameter # F0h, 7Dh The Code 39 and Codabar symbologies have an intercharacter gap that is typically quite small. Due to various bar code-printing technologies, this gap can grow larger than the maximum size allowed, preventing the digital scanner from decoding the symbol. If this problem occurs, scan the Large Intercharacter Gaps parameter to tolerate these out-of-specification bar codes.
Symbologies 13 - 81 Macro PDF Features Macro PDF is a special feature for concatenating multiple PDF symbols into one file. The digital scanner can decode symbols that are encoded with this feature, and can store more than 64 Kb of decoded data stored in up to 50 MacroPDF symbols. CAUTION When printing, keep each Macro PDF sequence separate, as each sequence has unique identifiers. Do not mix bar codes from several Macro PDF sequences, even if they encode the same data.
13 - 82 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 14 Driver’s License Set Up (DS6708-DL) Introduction The DS6708-DL digital scanner is capable of parsing out information from standard US driver's licenses and certain other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. Parsing can be achieved in one of two ways: • Internally embedded algorithms - scanning bar codes activate algorithms internally embedded in the digital scanner to produce formatted data.
14 - 2 Symbol DS6708 Digital Scanner Product Reference Guide Driver’s License Parsing There are three options available for programming the digital scanner: • No driver's license parsing (default) - disables the feature. • Embedded driver's license parsing - this does not require Motorola software (.DLL). Scan the bar codes on the following pages in the order indicating the sequence of data fields that the digital scanner outputs.
Driver’s License Set Up (DS6708-DL) 14 - 3 Parsing Driver’s License Data Fields (Embedded Driver's License Parsing) To begin programming a parsing rule: 1. Scan Begin New Driver’s License Parse Rule below. 2. Scan any of the field bar codes on the following pages, or Send Keystroke (Control Characters and Keyboard Characters) on page 14-21 to complete the parsing rule. 3. After entering the entire rule, scan Save Driver’s License Parse Rule to save the rule.
14 - 4 Symbol DS6708 Digital Scanner Product Reference Guide Driver’s License Parse Field Bar Codes (continued) The parse fields currently supported begin below. Not all IDs present data in the same format. For example, some IDs may have separate fields for first name, last name, and middle initial and others may have a single field with the entire name. In addition, some IDs may expire on the subject's birth date and the actual expiration date field may only indicate the year.
Driver’s License Set Up (DS6708-DL) 14 - 5 Driver’s License Parse Field Bar Codes (continued) Issue Date ID Number (Formatted)
14 - 6 Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes AAMVA Issuer ID Full Name Last Name First Name Middle Name / Initial Name Suffix Name Prefix
Driver’s License Set Up (DS6708-DL) 14 - 7 AAMVA Parse Field Bar Codes (continued) Mailing Address Line 1 Mailing Address Line 2 Mailing Address City Mailing Address State Mailing Address Postal Code Home Address Line 1 Home Address Line 2
14 - 8 Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes (continued) Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements
Driver’s License Set Up (DS6708-DL) 14 - 9 AAMVA Parse Field Bar Codes (continued) Height (Feet and/or Inches) Height (Centimeters) Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date
14 - 10 Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes (continued) Birth Date Gender License Issue Date Social Security Number Permit Class Permit Expiration Date Permit ID Number
Driver’s License Set Up (DS6708-DL) 14 - 11 AAMVA Parse Field Bar Codes (continued) Permit Issue Date Permit Restrictions Permit Endorsements AKA Social Security Name AKA Full Name AKA Last Name AKA First Name
14 - 12 Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes (continued) AKA Middle Name / Initial AKA Name Suffix AKA Name Prefix AKA Birth Date Issue Timestamp Number of Duplicates Medical Codes
Driver’s License Set Up (DS6708-DL) 14 - 13 AAMVA Parse Field Bar Codes (continued) Organ Donor Nonresident Customer ID Weight Range Document Discriminator Country Federal Commission Codes
14 - 14 Symbol DS6708 Digital Scanner Product Reference Guide AAMVA Parse Field Bar Codes (continued) Place of Birth Audit Information Inventory Control Race / Ethnicity Std Vehicle Class Std Endorsements Std Restrictions
Driver’s License Set Up (DS6708-DL) 14 - 15 AAMVA Parse Field Bar Codes (continued) Class Description Endorsement Description Restrictions Description Height in Inches Height in Centimeters Parser Version ID Bar Codes Include this field to emit embedded parser software version identification Parser Version ID
14 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Parsing Rule Example Scan the following bar codes in sequence to program the digital scanner to extract and transmit first, middle, and last names; mailing address line 1; mailing address line 2; mailing address city; mailing address state; mailing address postal code; and, date of birth. Then, scan a driver’s license bar code. NOTE This example applies to RS-232.
Driver’s License Set Up (DS6708-DL) 14 - 17 Parsing Rule Example (continued) 6 Send Space 7 Last Name 8 Send Control M (Carriage Return) 9 Mailing Address Line 1 10 Send Space 11 Mailing Address Line 2
14 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Parsing Rule Example (continued) 12 Send Control M (Carriage Return) 13 Mailing Address City 14 Send Space 15 Mailing Address State 16 Send Space 17 Mailing Address Postal Code
Driver’s License Set Up (DS6708-DL) 14 - 19 Parsing Rule Example (continued) 18 Send Control M (Carriage Return) 19 Birth Date 20 Send Control M (Carriage Return) 21 Save Driver’s Licence Parse Rule
14 - 20 Symbol DS6708 Digital Scanner Product Reference Guide Field Update Procedure Scan the following bar codes in order to perform a field update. This update COMPLETELY REPLACES any prior updates that were done and overrides any embedded parsing software currently programmed in the digital scanner. 1. Field Update Start. Field Update Start 2. Scan the entire set of PDF bar codes provided separately. 3. Field Update End.
Driver’s License Set Up (DS6708-DL) 14 - 21 User Preferences Set Default Parameter Scan this bar code to return all parameters to the default values listed in Table A-1 on page A-1. *Set All Defaults Send Keystroke (Control Characters and Keyboard Characters) Control Characters Scan a Send bar code for the keystroke to send.
14 - 22 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control C Send Control D Send Control E Send Control F Send Control G Send Control H Send Control I (Tab)
Driver’s License Set Up (DS6708-DL) 14 - 23 Control Characters (continued) Send Control J Send Control K Send Control L Send Control M (Carriage Return) Send Control N Send Control O Send Control P
14 - 24 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control Q Send Control R Send Control S Send Control T Send Control U Send Control V Send Control W
Driver’s License Set Up (DS6708-DL) 14 - 25 Control Characters (continued) Send Control X Send Control Y Send Control Z Send Control [ Send Control \ Send Control ]
14 - 26 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control 6 Send Control - Keyboard Characters Scan a Send bar code for the keyboard characters to send.
Driver’s License Set Up (DS6708-DL) 14 - 27 Keyboard Characters (continued) Send $ Send % Send & Send ‘ Send ( Send ) Send *
14 - 28 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send + Send , Send - Send .
Driver’s License Set Up (DS6708-DL) 14 - 29 Keyboard Characters (continued) Send 2 Send 3 Send 4 Send 5 Send 6 Send 7 Send 8
14 - 30 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send 9 Send : Send ; Send < Send = Send > Send ?
Driver’s License Set Up (DS6708-DL) 14 - 31 Keyboard Characters (continued) Send @ Send A Send B Send C Send D Send E Send F
14 - 32 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send G Send H Send I Send J Send K Send L Send M
Driver’s License Set Up (DS6708-DL) 14 - 33 Keyboard Characters (continued) Send N Send O Send P Send Q Send R Send S Send T
14 - 34 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send U Send V Send W Send X Send Y Send Z Send [
Driver’s License Set Up (DS6708-DL) 14 - 35 Keyboard Characters (continued) Send \ Send ] Send ^ Send _ Send ` Send a Send b
14 - 36 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send c Send d Send e Send f Send g Send h Send i
Driver’s License Set Up (DS6708-DL) 14 - 37 Keyboard Characters (continued) Send j Send k Send l Send m Send n Send o Send p
14 - 38 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send q Send r Send s Send t Send u Send v Send w
Driver’s License Set Up (DS6708-DL) 14 - 39 Keyboard Characters (continued) Send x Send y Send z Send { Send | Send } Send ~
14 - 40 Symbol DS6708 Digital Scanner Product Reference Guide
Chapter 15 Advanced Data Formatting Introduction Advanced Data Formatting (ADF) is a means of customizing data before transmission to the host device. Use ADF to edit scan data to suit particular requirements. To implement ADF, scan a related series of bar codes, which begin on page 15-7, or install the 123Scan utility (see Chapter 12, 123Scan) which allows programming the digital scanner with ADF rules. Avoid using ADF formatting with bar codes containing more than 60 characters.
15 - 2 Symbol DS6708 Digital Scanner Product Reference Guide Using ADF Bar Codes When programming a rule, make sure the rule is logically correct. Plan ahead before scanning. To program each data formatting rule: • Start the Rule. Scan the Begin New Rule bar code on page 15-7. • Specify Criteria. Scan the bar codes for all pertinent criteria. Criteria can include code type (e.g., Code 128), code length, or data that contains a specific character string (e.g., the digits “129”).
Advanced Data Formatting 15 - 3 Rule 1: The Code 128 Scanning Rule Step Bar Code On Page Beep Indication 1 Begin New Rule 15-7 High High 2 Code 128 15-10 High High 3 Send next 5 characters 15-27 High High 4 Send 15-49 High High 5 Send next 5 characters 15-27 High High 6 Send 15-49 High High 7 Send next 2 characters 15-26 High High 8 Send 15-48 High High 9 Save Rule 15-8 High Low High Low Rule 2: The UPC Scanning Rule Step Bar Code On Pag
15 - 4 Symbol DS6708 Digital Scanner Product Reference Guide and the cashier keys the price manually. To implement this, first enter an ADF rule that applies to the normal situation, such as: Scan Rule Belongs to Set 1. When scanning a bar code of length 15, send the next 2 characters, send the class key, send the next 8 characters, send the stock key, send the data that remains, send the Enter key. The “sale” rule may look like this: Scan Rule Belongs to Set 2.
Advanced Data Formatting 15 - 5 Note that using the standard data editing functions also creates ADF rules. Scan options are entered as ADF rules, and the hierarchy mentioned above also applies to them. For the digital scanner, this applies to prefix/suffix programming in the parameter Scan Data Transmission Format on page 4-18. These rules reside in the same “rule list” as ADF Rules, so the order you create them is also important. Default Rules Every unit has a default rule to send all scan data.
15 - 6 Symbol DS6708 Digital Scanner Product Reference Guide Table 15-1 ADF Bar Codes (Continued) Parameter Page Number Any Message OK 15-22 Numeric Keypad 15-23 Rule Belongs To Set 15-25 Actions Send Data 15-26 15-26 Send Data Up To Character 15-26 Send Next Character 15-26 Send All Data That Remains 15-26 Send Next 2 Characters - Send Next 20 Characters 15-26 Move Cursor 15-31 Send Pause 15-32 Skip Ahead 15-33 Skip Back 15-34 Send Preset Value 15-36 Remove All Spaces 15-37
Advanced Data Formatting 15 - 7 Table 15-1 ADF Bar Codes (Continued) Page Number Parameter Send Graphic User Interface (GUI) Characters 15-84 Send GUI 0 - Send GUI 9 15-84 Send GUI A - Send GUI Z 15-85 Turn On/Off Rule Sets 15-89 Alphanumeric Keyboard 15-91 Space - ‘ 15-91 0-9 15-95 A-Z 15-96 Cancel 15-100 End of Message 15-100 a-z 15-100 {-~ 15-104 Special Commands Pause Duration Use this parameter, along with Send Pause on page 15-32, to insert a pause in the data transmission.
15 - 8 Symbol DS6708 Digital Scanner Product Reference Guide Save Rule Scan the bar code below to save the rule. Save Rule Erase Use these bar codes to erase criteria, actions, or rules. Erase Criteria And Start Again Erase Actions And Start Again Erase Previously Saved Rule Erase All Rules Quit Entering Rules Scan the bar code below to quit entering rules.
Advanced Data Formatting Disable Rule Set Use these bar codes to disable rule sets.
15 - 10 Symbol DS6708 Digital Scanner Product Reference Guide Criteria Code Types Scan the bar codes for all code to be affected by the rule. Scan the codes in succession, prior to selecting other criteria. To select all code types, do not scan any code type.
Advanced Data Formatting Code Types (continued) IATA 2 OF 5 I 2 OF 5 Code 93 UPC-A UPC-E EAN-8 EAN-13 ISSN 15 - 11
15 - 12 Symbol DS6708 Digital Scanner Product Reference Guide Code Types (continued) MSI GS1-128 (formerly UCC/EAN-128 UPC-E1 Bookland EAN Trioptic Code 39 Code 11 Code 32
Advanced Data Formatting Code Types (continued) ISBT 128 Coupon Code Chinese 2 of 5 Matrix 2 of 5 US Postnet US Planet UK Postal 15 - 13
15 - 14 Symbol DS6708 Digital Scanner Product Reference Guide Code Types (continued) Japan Postal Australian Postal Netherlands KIX Code USPS 4CB/One Code/Intelligent Mail UPU FICS Postal PDF417 MicroPDF
Advanced Data Formatting Code Types (continued) Macro PDF Macro MicroPDF MaxiCode Data Matrix QR Code MicroQR TLC 39 15 - 15
15 - 16 Symbol DS6708 Digital Scanner Product Reference Guide Code Types (continued) UPC/EAN Composites GS1 DataBar and GS1-128 Composites Aztec Aztec Rune NOTE When selecting composite bar codes, enable AIM IDs if parsing UPC or EAN composite data, or data from an application that uses symbol separators.
Advanced Data Formatting 15 - 17 Code Lengths Scan these bar codes to define the number of characters the selected code type must contain. Select one length per rule only. Do not select any code length to select code types of any length.
15 - 18 Symbol DS6708 Digital Scanner Product Reference Guide Code Lengths (continued) 7 Characters 8 Characters 9 Characters 10 Characters 11 Characters 12 Characters 13 Characters
Advanced Data Formatting Code Lengths (continued) 14 Characters 15 Characters 16 Characters 17 Characters 18 Characters 19 Characters 20 Characters 15 - 19
15 - 20 Symbol DS6708 Digital Scanner Product Reference Guide Code Lengths (continued) 21 Characters 22 Characters 23 Characters 24 Characters 25 Characters 26 Characters 27 Characters
Advanced Data Formatting 15 - 21 Code Lengths (continued) 28 Characters 29 Characters 30 Characters Message Containing A Specific Data String Use this feature to select whether the formatting affects data that begins with a specific character or data string, or contains a specific character or data string. There are 5 features: • Specific String at Start • Specific String, Any Location • Specific String Search • Any Message OK • Rule Belongs to Set Specific String at Start 1.
15 - 22 Symbol DS6708 Digital Scanner Product Reference Guide Specific String, Any Location 1. Scan the following bar code. 2. Enter a location by scanning a two-digit number representing the position (use a leading “zero” if necessary) using the Numeric Keypad on page 15-23. 3. Scan the bar codes representing the desired character or characters (up to a total of 8) using the Alphanumeric Keyboard on page 15-91. 4. Scan End of Message bar code on page 15-100.
Advanced Data Formatting Numeric Keypad Do not confuse bar codes on this page with those on the alphanumeric keyboard.
15 - 24 Symbol DS6708 Digital Scanner Product Reference Guide Numeric Keypad (continued) 7 8 9 Cancel
Advanced Data Formatting 15 - 25 Rule Belongs To Set Select the set to which a rule belongs. There are four possible rule sets. See Alternate Rule Sets on page 15-3 for more information about rule sets.
15 - 26 Symbol DS6708 Digital Scanner Product Reference Guide Actions Select how to format the data for transmission. Send Data Send all data that follows, send all data up to a specific character selected from the Alphanumeric Keyboard on page 15-91, or send the next X characters. Note that only bar codes for Send Next 1 to 20 appear here, and can be scanned multiple times to send values greater then 20.
Advanced Data Formatting Send Data (continued) Send Next 5 Characters Send Next 6 Characters Send Next 7 Characters Send Next 8 Characters Send Next 9 Characters Send Next 10 Characters Send Next 11 Characters 15 - 27
15 - 28 Symbol DS6708 Digital Scanner Product Reference Guide Send Data (continued) Send Next 12 Characters Send Next 13 Characters Send Next 14 Characters Send Next 15 Characters Send Next 16 Characters Send Next 17 Characters Send Next 18 Characters
Advanced Data Formatting Send Data (continued) Send Next 19 Characters Send Next 20 Characters 15 - 29
15 - 30 Symbol DS6708 Digital Scanner Product Reference Guide Setup Field(s) Table 15-2 Setup Field(s) Definitions Parameter Description Page Move Cursor Move Cursor To a Character Scan the Move Cursor To Character, then any printable ASCII character from the Alphanumeric Keyboard on page 15-91. This moves the cursor to the position after the matching character. If the character is not there, the rule fails and ADF tries the next rule.
Advanced Data Formatting 15 - 31 Table 15-2 Setup Field(s) Definitions (Continued) Parameter Description Page Skip Ahead “N” Characters Scan one of these bar codes to select the number of positions ahead to move the cursor. 15-33 Skip Back “N” Characters Scan one of these bar codes to select the number of positions back to move the cursor. 15-34 Send Preset Value Send Values 1 through 6 by scanning the appropriate bar code.
15 - 32 Symbol DS6708 Digital Scanner Product Reference Guide Setup Field(s) (continued) Move Cursor to Specific String and Replace Move Cursor to Last Occurrence of String and Replace All Skip to End Send Pause Scan the bar code below to insert a pause in the transmission of data. See Pause Duration on page 15-7 to set the length of this pause.
Advanced Data Formatting Skip Ahead Use the following bar codes to skip ahead characters.
15 - 34 Symbol DS6708 Digital Scanner Product Reference Guide Skip Ahead (continued) Skip Ahead 8 Characters Skip Ahead 9 Characters Skip Ahead 10 Characters Skip Back Use the following bar codes to skip back characters.
Advanced Data Formatting Skip Back (continued) Skip Back 4 Characters Skip Back 5 Characters Skip Back 6 Characters Skip Back 7 Characters Skip Back 8 Characters Skip Back 9 Characters Skip Back 10 Characters 15 - 35
15 - 36 Symbol DS6708 Digital Scanner Product Reference Guide Send Preset Value Use these bar codes to send preset values. See Prefix/Suffix Values on page 4-17 to set these values.
Advanced Data Formatting 15 - 37 Modify Data Modify data as described below. The following actions work for all commands that follow it within a rule. Programming pad zeros to length 6, send next 3 characters, stop padding, send next 5 characters, adds three zeros to the first send, and the next send is unaffected by the padding. These options do not apply to the Send Keystroke or Send Preset Value options. Remove All Spaces To remove all spaces in the commands that follow, scan the bar code below.
15 - 38 Symbol DS6708 Digital Scanner Product Reference Guide Pad Data with Spaces To pad data to the left, scan the bar code containing the desired number of spaces. Use Send commands to activate this parameter.
Advanced Data Formatting Pad Data with Spaces (continued) Pad Spaces To Length 8 Pad Spaces To Length 9 Pad Spaces To Length 10 Pad Spaces To Length 11 Pad Spaces To Length 12 Pad Spaces To Length 13 Pad Spaces To Length 14 15 - 39
15 - 40 Symbol DS6708 Digital Scanner Product Reference Guide Pad Data with Spaces (continued) Pad Spaces To Length 15 Pad Spaces To Length 16 Pad Spaces To Length 17 Pad Spaces To Length 18 Pad Spaces To Length 19 Pad Spaces To Length 20 Pad Spaces To Length 21
Advanced Data Formatting Pad Data with Spaces (continued) Pad Spaces To Length 22 Pad Spaces To Length 23 Pad Spaces To Length 24 Pad Spaces To Length 25 Pad Spaces To Length 26 Pad Spaces To Length 27 Pad Spaces To Length 28 15 - 41
15 - 42 Symbol DS6708 Digital Scanner Product Reference Guide Pad Data with Spaces (continued) Pad Spaces To Length 29 Pad Spaces To Length 30 Stop Pad Spaces Pad Data with Zeros To pad data to the left, scan the bar code containing the desired number of zeros. Use Send commands to activate this parameter.
Advanced Data Formatting Pad Data with Zeros (continued) Pad Zeros To Length 4 Pad Zeros To Length 5 Pad Zeros To Length 6 Pad Zeros To Length 7 Pad Zeros To Length 8 Pad Zeros To Length 9 Pad Zeros To Length 10 15 - 43
15 - 44 Symbol DS6708 Digital Scanner Product Reference Guide Pad Data with Zeros (continued) Pad Zeros To Length 11 Pad Zeros To Length 12 Pad Zeros To Length 13 Pad Zeros To Length 14 Pad Zeros To Length 15 Pad Zeros To Length 16 Pad Zeros To Length 17
Advanced Data Formatting Pad Data with Zeros (continued) Pad Zeros To Length 18 Pad Zeros To Length 19 Pad Zeros To Length 20 Pad Zeros To Length 21 Pad Zeros To Length 22 Pad Zeros To Length 23 Pad Zeros To Length 24 15 - 45
15 - 46 Symbol DS6708 Digital Scanner Product Reference Guide Pad Data with Zeros (continued) Pad Zeros To Length 25 Pad Zeros To Length 26 Pad Zeros To Length 27 Pad Zeros To Length 28 Pad Zeros To Length 29 Pad Zeros To Length 30 Stop Pad Zeros
Advanced Data Formatting Beeps Select a beep sequence for each ADF rule. Beep Once Beep Twice Beep Three Times Send Keystroke (Control Characters and Keyboard Characters) Control Characters Scan a Send bar code for the keystroke to send.
15 - 48 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control C Send Control D Send Control E Send Control F Send Control G Send Control H Send Control I
Advanced Data Formatting Control Characters (continued) Send Control J Send Control K Send Control L Send Control M Send Control N Send Control O Send Control P 15 - 49
15 - 50 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control Q Send Control R Send Control S Send Control T Send Control U Send Control V Send Control W
Advanced Data Formatting Control Characters (continued) Send Control X Send Control Y Send Control Z Send Control [ Send Control \ Send Control ] 15 - 51
15 - 52 Symbol DS6708 Digital Scanner Product Reference Guide Control Characters (continued) Send Control 6 Send Control - Keyboard Characters Scan a Send bar code for the keyboard characters to send.
Advanced Data Formatting Keyboard Characters (continued) Send $ Send % Send & Send ‘ Send ( Send ) Send * 15 - 53
15 - 54 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send + Send , Send - Send .
Advanced Data Formatting Keyboard Characters (continued) Send 2 Send 3 Send 4 Send 5 Send 6 Send 7 Send 8 15 - 55
15 - 56 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send 9 Send : Send ; Send < Send = Send > Send ?
Advanced Data Formatting Keyboard Characters (continued) Send @ Send A Send B Send D Send E Send F 15 - 57
15 - 58 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send G Send H Send I Send J Send K Send L Send M
Advanced Data Formatting Keyboard Characters (continued) Send N Send O Send P Send Q Send R Send S Send T 15 - 59
15 - 60 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send U Send V Send W Send X Send Y Send Z Send [
Advanced Data Formatting Keyboard Characters (continued) Send \ Send ] Send ^ Send _ Send ` Send a Send b 15 - 61
15 - 62 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send d Send e Send f Send g Send h Send i
Advanced Data Formatting Keyboard Characters (continued) Send j Send k Send l Send m Send n Send o Send p 15 - 63
15 - 64 Symbol DS6708 Digital Scanner Product Reference Guide Keyboard Characters (continued) Send q Send r Send s Send t Send u Send v Send w
Advanced Data Formatting Keyboard Characters (continued) Send x Send y Send z Send { Send | Send } Send ~ 15 - 65
15 - 66 Symbol DS6708 Digital Scanner Product Reference Guide Send ALT Characters Send Alt 2 Send Alt A Send Alt B Send Alt C Send Alt D Send Alt E Send Alt F
Advanced Data Formatting Send ALT Characters (continued) Send Alt G Send Alt H Send Alt I Send Alt J Send Alt K Send Alt L Send Alt M 15 - 67
15 - 68 Symbol DS6708 Digital Scanner Product Reference Guide Send ALT Characters (continued) Send Alt N Send Alt O Send Alt P Send Alt Q Send Alt R Send Alt S Send Alt T
Advanced Data Formatting Send ALT Characters (continued) Send Alt U Send Alt V Send Alt W Send Alt X Send Alt Y Send Alt Z Send Alt [ 15 - 69
15 - 70 Symbol DS6708 Digital Scanner Product Reference Guide Send ALT Characters (continued) Send Alt \ Send Alt ]
Advanced Data Formatting Send Keypad Characters Send Keypad * Send Keypad + Send Keypad - Send Keypad .
15 - 72 Symbol DS6708 Digital Scanner Product Reference Guide Send Keypad Characters (continued) Send Keypad 2 Send Keypad 3 Send Keypad 4 Send Keypad 5 Send Keypad 6 Send Keypad 7 Send Keypad 8
Advanced Data Formatting Send Keypad Characters (continued) Send Keypad 9 Send Keypad Enter Send Keypad Numlock Send Break Key Send Delete Key Send Page Up Key Send End Key 15 - 73
15 - 74 Symbol DS6708 Digital Scanner Product Reference Guide Send Keypad Characters (continued) Send Page Down Key Send Pause Key Send Scroll Lock Key Send Backspace Key Send Tab Key Send Print Screen Key Send Insert Key
Advanced Data Formatting Send Keypad Characters (continued) Send Home Key Send Enter Key Send Escape Key Send Up Arrow Key Send Down Arrow Key Send Left Arrow Key Send Right Arrow Key 15 - 75
15 - 76 Symbol DS6708 Digital Scanner Product Reference Guide Send Function Key Send F1 Key Send F2 Key Send F3 Key Send F4 Key Send F5 Key Send F6 Key Send F7 Key
Advanced Data Formatting Send Function Key (continued) Send F8 Key Send F9 Key Send F10 Key Send F11 Key Send F12 Key Send F13 Key Send F14 Key 15 - 77
15 - 78 Symbol DS6708 Digital Scanner Product Reference Guide Send Function Key (continued) Send F15 Key Send F16 Key Send F17 Key Send F18 Key Send F19 Key Send F20 Key Send F21 Key
Advanced Data Formatting Send Function Key (continued) Send F22 Key Send F23 Key Send F24 Key Send PF1 Key Send PF2 Key Send PF3 Key Send PF4 Key 15 - 79
15 - 80 Symbol DS6708 Digital Scanner Product Reference Guide Send Function Key (continued) Send PF5 Key Send PF6 Key Send PF7 Key Send PF8 Key Send PF9 Key Send PF10 Key Send PF11 Key
Advanced Data Formatting Send Function Key (continued) Send PF12 Key Send PF13 Key Send PF14 Key Send PF15 Key Send PF16 Key Send PF17 Key Send PF18 Key 15 - 81
15 - 82 Symbol DS6708 Digital Scanner Product Reference Guide Send Function Key (continued) Send PF19 Key Send PF20 Key Send PF21 Key Send PF22 Key Send PF23 Key Send PF24 Key Send PF25 Key
Advanced Data Formatting Send Function Key (continued) Send PF26 Key Send PF27 Key Send PF28 Key Send PF29 Key Send PF30 Key Send Right Control Key The Send Right Control Key action sends a tap (press and release) of the Right Control Key.
15 - 84 Symbol DS6708 Digital Scanner Product Reference Guide Send Graphic User Interface (GUI) Characters The Send Graphic User Interface Character actions taps the specified key while holding the System Dependent Graphic User Interface (GUI) Key. The definition of the Graphic User Interface key depends on the attached system.
Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI 6 Send GUI 7 Send GUI 8 Send GUI 9 Send GUI A Send GUI B Send GUI C 15 - 85
15 - 86 Symbol DS6708 Digital Scanner Product Reference Guide Send Graphic User Interface (GUI) Characters (continued) Send GUI D Send GUI E Send GUI F Send GUI G Send GUI H Send GUI I Send GUI J
Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI K Send GUI L Send GUI M Send GUI N Send GUI O Send GUI P Send GUI Q 15 - 87
15 - 88 Symbol DS6708 Digital Scanner Product Reference Guide Send Graphic User Interface (GUI) Characters (continued) Send GUI R Send GUI S Send GUI T Send GUI U Send GUI V Send GUI W Send GUI X
Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI Y Send GUI Z Turn On/Off Rule Sets Use these bar codes to turn rule sets on and off.
15 - 90 Symbol DS6708 Digital Scanner Product Reference Guide Turn On/Off Rule Sets (continued) Use these bar codes to turn rule sets on and off.
Advanced Data Formatting Alphanumeric Keyboard Space # $ % * + (Dash) 15 - 91
15 - 92 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) .
Advanced Data Formatting Alphanumeric Keyboard (continued) ) : ; < = > ? 15 - 93
15 - 94 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) @ [ \ ] ^ _ (Underscore) `
Advanced Data Formatting Alphanumeric Keyboard (continued) NOTE Do not confuse the numeric bar codes below with those on the numeric keypad.
15 - 96 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) 6 7 8 9 A B C
Advanced Data Formatting Alphanumeric Keyboard (continued) D E F G H I J 15 - 97
15 - 98 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) K L M N O P Q
Advanced Data Formatting Alphanumeric Keyboard (continued) R S T U V W X 15 - 99
15 - 100 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) Y Z Cancel End of Message a b c
Advanced Data Formatting 15 - 101 Alphanumeric Keyboard (continued) d e f g h i j
15 - 102 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) k l m n o p q
Advanced Data Formatting 15 - 103 Alphanumeric Keyboard (continued) r s t u v w x
15 - 104 Symbol DS6708 Digital Scanner Product Reference Guide Alphanumeric Keyboard (continued) y z { | } ~
Appendix A Standard Default Parameters Table A-1 Standard Default Parameters Table Parameter Parameter Number Default Page Number User Preferences Set Default Parameter Restore Defaults 4-4 Parameter Scanning ECh Enable 4-5 Beeper Tone 91h Medium 4-6 Beeper Volume 8Ch High 4-6 Power Mode 80h Continuous On 4-7 Time Delay to Low Power Mode 92h 1 Minute 4-8 Trigger Mode 8Ah Auto Aim 4-9 Picklist Mode F0h 92h Disabled Always 4-10 Presentation Mode F1h, 74h 3 Sec 4-11 Dec
A-2 Symbol DS6708 Digital Scanner Product Reference Guide Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number Miscellaneous Scanner Options Transmit Code ID Character 2Dh None 4-16 Prefix Value 63h, 69h 7013 4-17 Suffix 1 Value Suffix 2 Value 62h, 68h 64h, 6Ah 7013 4-17 Scan Data Transmission Format EBh Data as is 4-18 FN1 Substitution Values 67h, 6Dh Set 4-19 Transmit “No Read” Message 5Eh Disable 4-20 Synap
Standard Default Parameters Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number RS-232 Host Parameters RS-232 Host Types Standard1 7-7 Baud Rate 9600 7-8 Parity Type None 7-10 Stop Bit Select 1 Stop Bit 7-11 Data Bits 8-Bit 7-11 Check Receive Errors Enable 7-12 Hardware Handshaking None 7-12 Software Handshaking None 7-14 Host Serial Response Time-out 2 Sec 7-16 RTS Line State Low RTS 7-17 Beep on Disable 7-17 In
A-4 Symbol DS6708 Digital Scanner Product Reference Guide Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number Keyboard Wedge Host Parameters Keyboard Wedge Host Type IBM PC/AT& IBM PC Compatibles1 10-5 Country Types (Country Codes) North American 10-6 Ignore Unknown Characters Transmit 10-8 Keystroke Delay No Delay 10-8 Intra-Keystroke Delay Disable 10-9 Alternate Numeric Keypad Emulation Disable 10-9 Caps Lock On Disable 10-10 C
Standard Default Parameters Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number UPC/EAN UPC-A 01h Enable 13-7 UPC-E 02h Enable 13-7 UPC-E1 0Ch Disable 13-8 EAN-8/JAN 8 04h Enable 13-8 EAN-13/JAN 13 03h Enable 13-9 Bookland EAN 53h Disable 13-9 Decode UPC/EAN/JAN Supplementals (2 and 5 digits) 10h Ignore 13-10 User-Programmable Supplementals Supplemental 1: Supplemental 2: F1h 43h F1h 44h 13-13 UPC/EAN/JAN Supplemental Re
A-6 Symbol DS6708 Digital Scanner Product Reference Guide Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number ISBT 128 54h Enable 13-25 ISBT Concatenation F1h 41h Disable 13-26 Check ISBT Table F1h 42h Enable 13-27 ISBT Concatenation Redundancy DFh 10 13-27 Code 39 00h Enable 13-28 Trioptic Code 39 0Dh Disable 13-28 Convert Code 39 to Code 32 (Italian Pharmacy Code) 56h Disable 13-29 Code 32 Prefix E7h Disable 13-29 Se
Standard Default Parameters Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number Discrete 2 of 5 (DTF) Discrete 2 of 5 05h Disable 13-45 Set Length(s) for D 2 of 5 14h 15h 12 13-46 Codabar 07h Disable 13-48 Set Lengths for Codabar 18h 19h 5 to 55 13-48 CLSI Editing 36h Disable 13-50 NOTIS Editing 37h Disable 13-50 MSI 0Bh Disable 13-51 Set Length(s) for MSI 1Eh 1Fh 4 to 55 13-51 MSI Check Digits 32h One 13-53 Transmi
A-8 Symbol DS6708 Digital Scanner Product Reference Guide Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number UK Postal 5Bh Enable 13-61 Transmit UK Postal Check Digit 60h Enable 13-62 Japan Postal F0h 22h Enable 13-62 Australian Postal F0h 23h Enable 13-63 Netherlands KIX Code F0h 46h Enable 13-63 USPS 4CB/One Code/Intelligent Mail F1h 50h Disable 13-64 UPU FICS Postal F1h 63h Disable 13-64 GS1 DataBar-14 F0h 52h Enable
Standard Default Parameters Table A-1 Standard Default Parameters Table (Continued) Parameter Parameter Number Default Page Number QR Code F0h 25h Enable 13-74 QR Inverse F1h 4Bh Regular 13-74 MicroQR F1h 3Dh Enable 13-75 Aztec F1h 3Eh Enable 13-75 Aztec Inverse F1h 4Dh Regular 13-76 Redundancy Level 4Eh 1 13-77 Security Level 4Dh 1 13-79 Intercharacter Gap Size F0h 7Dh Normal 13-80 Symbology-Specific Security Levels Report Version 13-80 Macro PDF Flush Macro PDF Buf
A - 10 Symbol DS6708 Digital Scanner Product Reference Guide
Appendix B Programming Reference Symbol Code Identifiers Table B-1 Symbol Code Characters Code Character Code Type A UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13 B Code 39, Code 32 C Codabar D Code 128, ISBT 128, ISBT 128 Concatenated E Code 93 F Interleaved 2 of 5 G Discrete 2 of 5, or Discrete 2 of 5 IATA H Code 11 J MSI K GS1-128 (formerly UCC/EAN-128) L Bookland EAN M Trioptic Code 39 N Coupon Code R GS1 DataBar Family S Matrix 2 of 5 T UCC Composite, TLC 39 U Chinese 2 of 5
B-2 Symbol DS6708 Digital Scanner Product Reference Guide Table B-1 Symbol Code Characters (Continued) Code Character Code Type X ISSN EAN, PDF417, Macro PDF417, Micro PDF417 z Aztec, Aztec Rune P00 Data Matrix P01 QR Code, MicroQR P02 Maxicode P03 US Postnet P04 US Planet P05 Japan Postal P06 UK Postal P08 Netherlands KIX Code P09 Australian Postal P0A USPS 4CB/One Code/Intelligent Mail P0B UPU FICS Postal
Programming Reference AIM Code Identifiers Each AIM Code Identifier contains the three-character string ]cm where: ] = Flag Character (ASCII 93) c = Code Character (see Table B-2) m = Modifier Character (see Table B-3) Table B-2 Aim Code Characters Code Character Code Type A Code 39, Code 39 Full ASCII, Code 32 C Code 128, ISBT 128, ISBT 128 Concatenated, GS1-128, Coupon (Code 128 portion) d Data Matrix E UPC/EAN, Coupon (UPC portion) e GS1 DataBar Family F Codabar G Code 93 H Code 11 I
B-4 Symbol DS6708 Digital Scanner Product Reference Guide The modifier character is the sum of the applicable option values based on Table B-3. Table B-3 Modifier Characters Code Type Code 39 Option Value Option 0 No check character or Full ASCII processing. 1 Reader has checked one check character. 3 Reader has checked and stripped check character. 4 Reader has performed Full ASCII character conversion. 5 Reader has performed Full ASCII character conversion and checked one check character.
Programming Reference Table B-3 Modifier Characters (Continued) Code Type D 2 of 5 Option Value 0 Option No options specified at this time. Always transmit 0. Example: A D 2 of 5 bar code 4123, is transmitted as ]S04123 UPC/EAN 0 Standard data packet in full EAN format, i.e. 13 digits for UPC-A, UPC-E, and EAN-13 (not including supplemental data). 1 Two digit supplemental data only. 2 Five digit supplemental data only.
B-6 Symbol DS6708 Digital Scanner Product Reference Guide Table B-3 Modifier Characters (Continued) Code Type EAN.UCC Composites (GS1 DataBar, GS1-128, 2D portion of UPC composite) Option Value Option Native mode transmission. Note: UPC portion of composite is transmitted using UPC rules. 0 Standard data packet. 1 Data packet containing the data following an encoded symbol separator character. 2 Data packet containing the data following an escape mechanism character.
Programming Reference Table B-3 Modifier Characters (Continued) Code Type Data Matrix MaxiCode QR Code Aztec Option Value Option 0 ECC 000-140, not supported. 1 ECC 200. 2 ECC 200, FNC1 in first or fifth position. 3 ECC 200, FNC1 in second or sixth position. 4 ECC 200, ECI protocol implemented. 5 ECC 200, FNC1 in first or fifth position, ECI protocol implemented. 6 ECC 200, FNC1 in second or sixth position, ECI protocol implemented. 0 Symbol in Mode 4 or 5. 1 Symbol in Mode 2 or 3.
B-8 Symbol DS6708 Digital Scanner Product Reference Guide
Appendix C Sample Bar Codes Code 39 123ABC UPC/EAN UPC-A, 100% 0 12345 67890 5
C-2 Symbol DS6708 Digital Scanner Product Reference Guide EAN-13, 100% 3 456789 012340 Code 128 12345678901234567890123456789012345678901234 Interleaved 2 of 5 12345678901231
Sample Bar Codes GS1 DataBar-14 NOTE DataBar-14 must be enabled to read the bar code below (see GS1 DataBar-14 on page 13-65).
C-4 Symbol DS6708 Digital Scanner Product Reference Guide Maxicode QR Code US Postnet UK Postal
Appendix D Numeric Bar Codes Numeric Bar Codes For parameters requiring specific numeric values, scan the appropriately numbered bar code(s).
D-2 Symbol DS6708 Digital Scanner Product Reference Guide Numeric Bar Codes (continued) 5 6 7 8 9 Cancel To correct an error or change a selection, scan the bar code below.
Appendix E ASCII Character Sets Table E-1 ASCII Value Table ASCII Value Full ASCII Code 39 Encode Char Keystroke 1000 %U CTRL 2 1001 $A CTRL A 1002 $B CTRL B 1003 $C CTRL C 1004 $D CTRL D 1005 $E CTRL E 1006 $F CTRL F 1007 $G CTRL G 1008 $H CTRL H/BACKSPACE1 1009 $I CTRL I/HORIZONTAL TAB1 1010 $J CTRL J 1011 $K CTRL K 1012 $L CTRL L 1013 $M CTRL M/ENTER1 1014 $N CTRL N 1015 $O CTRL O The keystroke in bold transmits only if you enabled Function Key Mapping
E-2 Symbol DS6708 Digital Scanner Product Reference Guide Table E-1 ASCII Value Table (Continued) ASCII Value Full ASCII Code 39 Encode Char Keystroke 1016 $P CTRL P 1017 $Q CTRL Q 1018 $R CTRL R 1019 $S CTRL S 1020 $T CTRL T 1021 $U CTRL U 1022 $V CTRL V 1023 $W CTRL W 1024 $X CTRL X 1025 $Y CTRL Y 1026 $Z CTRL Z 1027 %A CTRL [ 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL - 1032 Space Space 1033 /A ! 1034 /B “ 1035 /C # 1036 /D
ASCII Character Sets Table E-1 ASCII Value Table (Continued) Full ASCII Code 39 Encode Char ASCII Value Keystroke 1044 /L , 1045 - - 1046 . .
E-4 Symbol DS6708 Digital Scanner Product Reference Guide Table E-1 ASCII Value Table (Continued) Full ASCII Code 39 Encode Char ASCII Value Keystroke 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ‘ 1097 +A a 1098 +B b 1099 +C c The keystr
ASCII Character Sets Table E-1 ASCII Value Table (Continued) ASCII Value Full ASCII Code 39 Encode Char Keystroke 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q I 1125 %R } 1126 %S ~ The keystroke in bold transmits only if yo
E-6 Symbol DS6708 Digital Scanner Product Reference Guide Table E-2 ALT Key Standard Default Tables ALT Keys Keystroke 2064 ALT 2 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z
ASCII Character Sets Table E-3 USB GUI Key Character Set GUI Key Keystroke 3000 Right Control Key 3048 GUI 0 3049 GUI 1 3050 GUI 2 3051 GUI 3 3052 GUI 4 3053 GUI 5 3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on ei
E-8 Symbol DS6708 Digital Scanner Product Reference Guide Table E-3 USB GUI Key Character Set (Continued) GUI Key Keystroke 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key.
ASCII Character Sets Table E-4 PF Key Standard Default Table PF Keys Keystroke 4001 PF 1 4002 PF 2 4003 PF 3 4004 PF 4 4005 PF 5 4006 PF 6 4007 PF 7 4008 PF 8 4009 PF 9 4010 PF 10 4011 PF 11 4012 PF 12 4013 PF 13 4014 PF 14 4015 PF 15 4016 PF 16 E-9
E - 10 Symbol DS6708 Digital Scanner Product Reference Guide Table E-5 F key Standard Default Table F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F 10 5011 F 11 5012 F 12 5013 F 13 5014 F 14 5015 F 15 5016 F 16 5017 F 17 5018 F 18 5019 F 19 5020 F 20 5021 F 21 5022 F 22 5023 F 23 5024 F 24
ASCII Character Sets E - 11 Table E-6 Numeric Key Standard Default Table Numeric Keypad Keystroke 6042 * 6043 + 6044 Undefined 6045 - 6046 .
E - 12 Symbol DS6708 Digital Scanner Product Reference Guide Table E-7 Extended Keypad Standard Default Table Extended Keypad Keystroke 7001 Break 7002 Delete 7003 Pg Up 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert 7012 Home 7013 Enter 7014 Escape 7015 Up Arrow 7016 Dn Arrow 7017 Left Arrow 7018 Right Arrow
Glossary A Aperture. The opening in an optical system defined by a lens or baffle that establishes the field of view. API. An interface by means of which one software component communicates with or controls another. Usually used to refer to services provided by one software component to another, usually via software interrupts or function calls Application Programming Interface. See API. ASCII. American Standard Code for Information Interchange.
Glossary - 2 Symbol DS6708 Digital Scanner Product Reference Guide Bit. Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of data. The pattern of 0 and 1 values within the byte determines its meaning. Bits per Second (bps). Bits transmitted or received. Boot or Boot-up. The process a computer goes through when it starts. During boot-up, the computer can run self-diagnostic tests and configure hardware and software. BOOTP.
Glossary - 3 Code Length. Number of data characters in a bar code between the start and stop characters, not including those characters. Cold Boot. A cold boot restarts the mobile computer and erases all user stored records and entries. COM port. Communication port; ports are identified by number, e.g., COM1, COM2. Continuous Code. A bar code or symbol in which all spaces within the symbol are parts of characters. There are no intercharacter gaps in a continuous code.
Glossary - 4 Symbol DS6708 Digital Scanner Product Reference Guide F Flash Disk. An additional megabyte of non-volatile memory for storing application and configuration files. Flash Memory. Flash memory is responsible for storing the system firmware and is non-volatile. If the system power is interrupted the data is not be lost. FTP. See File Transfer Protocol. H Hard Reset. See Cold Boot. Host Computer.
Glossary - 5 group determines which characters are encoded. This continuous code type uses no intercharacter spaces. Only numeric (0 to 9) and START/STOP characters may be encoded. I/O Ports. interface The connection between two devices, defined by common physical characteristics, signal characteristics, and signal meanings. Types of interfaces include RS-232 and PCMCIA. IOCTL. Input/Output Control. IP Address. (Internet Protocol address) The address of a computer attached to an IP network.
Glossary - 6 Symbol DS6708 Digital Scanner Product Reference Guide M MIL. 1 mil = 1 thousandth of an inch. Misread (Misdecode). A condition which occurs when the data output of a reader or interface controller does not agree with the data encoded within a bar code symbol. N Nominal. The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive and negative deviations from this value. Nominal Size. Standard size for a bar code symbol.
Glossary - 7 Percent Decode. The average probability that a single scan of a bar code would result in a successful decode. In a well-designed bar code scanning system, that probability should approach near 100%. PING. (Packet Internet Groper) An Internet utility used to determine whether a particular IP address is online. It is used to test and debug a network by sending out a packet and waiting for a response. Print Contrast Signal (PCS).
Glossary - 8 Symbol DS6708 Digital Scanner Product Reference Guide S Scan Area. Area intended to contain a symbol. Scanner. An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol.
Glossary - 9 Symbol Length. Length of symbol measured from the beginning of the quiet zone (margin) adjacent to the start character to the end of the quiet zone (margin) adjacent to a stop character. Symbology. The structural rules and conventions for representing data within a particular bar code type (e.g. UPC/EAN, Code 39, PDF417, etc.). T TCP/IP. (Transmission Control Protocol/Internet Protocol) A communications protocol used to internetwork dissimilar systems.
Glossary - 10 Symbol DS6708 Digital Scanner Product Reference Guide UPC. Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars and two spaces, each of which is any of four widths. The standard symbology for retail food packages in the United States. V Visible Laser Diode (VLD). A solid state device which produces visible laser light. W Warm Boot. A warm boot restarts the mobile computer by closing all running programs.
Index Numerics 123Scan parameters . . . . . . . . . . . . . . . . . . . . . . . . 12-1 2D bar codes aztec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-75 aztec inverse . . . . . . . . . . . . . . . . . . . . . . . . . . 13-76 code 128 emulation . . . . . . . . . . . . . . . . . . . . . 13-71 Data Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-72 data matrix inverse . . . . . . . . . . . . . . . . . . . . . 13-72 Maxicode . . . . . . . . . . . . . . . . . . . . . . . .
Index - 2 DS6708 Digital Scanner Product Reference Guide alphanumeric keyboard . . . . . . . . . . . . . . . . . . 15-91 alternate rule sets . . . . . . . . . . . . . . . . . . . . . . . 15-3 bar code menu example . . . . . . . . . . . . . . . . . . 15-2 beep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-47 code lengths . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17 code types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-10 criteria . . . . . . . . . . . . . .
Index - 3 host types . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 ignore unknown characters . . . . . . . . . . . . 10-8 intra-keystroke delay . . . . . . . . . . . . . . . . . 10-9 keystroke delay . . . . . . . . . . . . . . . . . . . . . . 10-8 leading margin . . . . . . . . . . . . . . . . . . .11-10, 11-11 low light enhancement . . . . . . . . . . . . . . . . . . . . 5-5 Maxicode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-73 MicroPDF417 . . . . . . . . . . . . . . . . . .
Index - 4 DS6708 Digital Scanner Product Reference Guide UPC-A preamble . . . . . . . . . . . . . . . . . . . 13-16 UPC-A/E/E1 check digit . . . . . . . . .13-14, 13-15 UPC-E preamble . . . . . . . . . . . . . . . . . . . 13-17 UPU FICS postal . . . . . . . . . . . . . . . . . . . 13-64 US planet . . . . . . . . . . . . . . . . . . . . . . . . . 13-60 US postnet . . . . . . . . . . . . . . . . . . . . . . . . 13-60 USPS 4CB/one code/intelligent mail . . . . 13-64 transmission timeout . . . . . . . . . . .
Index - 5 standard default table . . . . . . . . . . . . . . . . . . . . . A-1 symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 user preferences . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 wand emulation . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 digital scanner defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 discrete 2 of 5 bar codes discrete 2 of 5 . . .
Index - 6 DS6708 Digital Scanner Product Reference Guide Q QR code bar codes . . . . . . . . . . . . . . . . . . . . . . . . 13-74 quiet zone (leading margin) . . . . . . . . . . . . . . . . . . . . 9-6 R RS-232 connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 default parameters . . . . . . . . . . . . . . . . . . . . . . . 7-4 parameters . . . . . . . . . . . . . . . . . . . . . . . . . .7-5, 7-7 S sample bar codes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tell Us What You Think... We’d like to know what you think about this Manual. Please take a moment to fill out this questionnaire and fax this form to: (631) 627-7184, or mail to: Motorola, Inc. One Symbol Plaza M/S B-10 Holtsville, NY 11742-1300 Attention: Advanced Data Capture Technical Publications Manager Important If you need product support, please call the appropriate customer support number for your area. Unfortunately, we cannot provide customer support at the fax number above.
Motorola, Inc. One Motorola Plaza Holtsville, New York 11742, USA 1-800-927-9626 http://www.motorola.com/enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their respective owners. © Motorola, Inc.
