User guide
Clock & alarm 13
6.
Re-enter the new PIN and press
OK
.
7.
Press
Back
to return to the previous menu level or to return
to standby.
Restore default settings
You can restore your D811 to its default (original) settings.
It will not affect the phonebook, calls list or user’s data, including
personal/recorded outgoing messages and answer machine
messages. All handsets registered to the base will be retained.
All text, answer machine, handset and base settings will be reset.
1.
Press
Menu
, scroll to
Settings
and press
Select
.
2.
Scroll to
Set Base
and press
Select
.
3.
Scroll to
Master Reset
and press
Select
.
4.
Select
Yes
to confirm or
No
to cancel.
5.
Enter the system PIN (original setting 0000) then press
OK
.
The display will show
Reset Compete
and the unit will restart.
If the welcome mode is available then the user is presented
with the country selection screen. Please refer to welcome
mode section.
ECO mode
To reduce the level of power emissions, you can select low
power or ECO mode. When the ECO mode is set to
On
, the
base transmission power will be reduced.
To turn ECO Mode to
On
or
Off
:
1.
Press
Menu
, scroll to
Settings
and press
Select
.
2.
Scroll to
Set Base
and press
Select
.
3.
Scroll to
ECO Mode
and press
Select
.
4.
Press or to highlight
On
or
Off
then press
Select
to
confirm.
The display will show
Set to ON
or
Set to OFF
depending on the
selection together with a confirmation tone.
When set to
ON
, icon is displayed in place of the standard
signal icon.
NOTE
When ECO mode is set to
ON
, the handset range will be reduced.
6. Clock & alarm
Date & time
If you subscribe to your network’s caller display service, the
base sets the date and time for all handsets whenever a call is
received. You can manually set the time on an individual
handset.
1.
Press
Menu
, scroll to
Clock & Alarm
and press
Select
.
2.
Date & Time
is highlighted, press
Select
.
3.
Enter the date using the format DD/MM/YY.
4.
Enter the time and press
Save
.
5.
Press
Back
to return to the previous menu level or to
return to standby.
Set alarm
When the alarm is set, the display shows the icon.
Each handset can have a different alarm setting.
1.
Press
Menu
, scroll to
Clock & Alarm
and press
Select
.
2.
Scroll to
Alarm
and press
Select
.
3.
Press or to select
On
and press
Select
.
4.
Press or to select
Once
,
Monday-Friday
or
On Daily
and
press
Select
.
5.
Enter the time you want the alarm and press
Save
.
6.
Press
Back
to return to the previous menu level or to
return to standby.
If the alarm was set to
Once
, the will disappear from the
screen.
If set to
On Daily
or
Monday-Friday
, the will remain on the
screen.
Alarm on /off
Once an alarm has been set, you can switch the setting On or
Off.
1.
Press
Menu,
scroll to
Clock & Alarm
and press
Select
.
2.
Scroll to
Alarm
and press
Select
.
3.
Press or to select
On
or
Off
and press
Select
.
4.
Press
Back
to return to the previous menu level.
Switch off alarm ring
When the alarm goes off, press
Stop
.
If you are using the handset to make a call when the alarm ring
is due, the flashes and you hear a beep in the earpiece.
Time format
Set the time format to 12 or 24 hour setting.
1.
Press
Menu
, scroll to
Clock & Alarm
and press
Select
.
2.
Scroll to
Time Format
and press
Select
.
3.
Press or to select
12 Hour
or
24 Hour
and press
Select
.
4.
Press
Back
to return to the previous menu level.
Signal icon in
ECO mode
EN
D811_IFU_EN.fm Page 13 Friday, September 7, 2007 7:37 PM