CPV8540 CompactPCI® Hot Swap PMC Carrier Card User Manual CPV8540A/UM1 March 2001
© Copyright 1999, 2001 Motorola, Inc. All rights reserved. Printed in the United States of America. CompactPCI® is a registered trademark of PCI Industrial Computer Manufacturers Group. Motorola and the Motorola symbol are registered trademarks of Motorola, Inc. All other products mentioned in this document are trademarks or registered trademarks of their respective holders.
Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment. The safety precautions listed below represent warnings of certain dangers of which Motorola is aware.
Flammability All Motorola PWBs (printed wiring boards) are manufactured with a flammability rating of 94V-0 by UL-recognized manufacturers. EMI Caution ! Caution This equipment generates, uses and can radiate electromagnetic energy. It may cause or be susceptible to electromagnetic interference (EMI) if not installed and used with adequate EMI protection. CE Notice (European Community) Motorola Computer Group products with the CE marking comply with the EMC Directive (89/336/EEC).
Notice While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omissions in this document, or from the use of the information obtained therein. Motorola reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Motorola to notify any person of such revision or changes.
Contents About This Manual Summary of Changes .................................................................................................xiii Comments and Suggestions .......................................................................................xiii Conventions Used in This Manual.............................................................................xiv CHAPTER 1 Introduction Product Description and Diagrams ............................................................................
List of Figures Figure 1-1. CPV8540 Block Diagram........................................................................1-3 Figure 1-2. PMC Modules to CPV8540 Carrier Card with Connectors Labeled ......
List of Tables Table 1-1. CPCI J3 User I/O Connector Pinout .........................................................1-5 Table 1-2. CPCI J5 User I/O Connector Pinout .........................................................1-5 Table 1-3. PCI Interface Connector Pinout: P11/J11, P21/J21 32-bit PCI ......................................................................................1-6 Table 1-4. PCI Interface Connector Pinout: P12/J12, P22/J22 32-bit PCI .....................................................
About This Manual The CPV8540 CompactPCI Hot Swap PMC Carrier Card User Manual provides a brief description and overview of this product. (PCI stands for Peripheral Component Interconnect and PMC stands for PCI Mezzanine Card.) The Manual also provides you with tables that include all the connector pinout information needed to attach one or two PMC mezzanine modules to the carrier card. This document should be used by anyone attaching PMC modules to this card.
In all your correspondence, please list your name, position, and company. Be sure to include the title and part number of the manual and tell how you used it. Then tell us your feelings about its strengths and weaknesses and any recommendations for improvements.
1Introduction 1 This manual provides a brief description and overview of the CPV8540 CompactPCI Hot Swap PMC Carrier Card together with the connector pinout information needed to attach one or two PMC mezzanine modules to the card. PCI stands for Peripheral Component Interconnect and PMC stands for PCI Mezzanine Card. Note The CPV8540 only allows 32-bit PCI transfers between itself and the CompactPCI bus. This product is being replaced by Motorola’s CPV8540B, which supports 64-bit PCI transfers.
1 Introduction ❏ Supports 5.0 or 3.3 volt PMC modules ❏ Supports Plug and Play Card ID: The CPV8540 reports itself to the system as a bridge chip with the PMC functions behind it. Block and Schematic Diagrams The following two figures provide overviews of the card.
Product Description and Diagrams J5 PMC2 J3 PMC1 J2 Bridge J1 Figure 1-1. CPV8540 Block Diagram http://www.motorola.
1 Introduction J22 J21 J24 J23 J12 J11 J14 J13 Single Width PMC Module Figure 1-2.
Connector Pinouts Connector Pinouts The tables in this section provide the connector pinout information needed to attach one or two PMC mezzanine modules to the carrier card. Table 1-1. CPCI J3 User I/O Connector Pinout ROW A ROW B ROW C ROW D ROW E 14 +3.3V +3.3V +3.
1 Introduction Table 1-2.
Connector Pinouts Table 1-3. PCI Interface Connector Pinout: P11/J11, P21/J21 32-bit PCI (Continued) Pin# Signal Name Signal Name Pin # 35 GND IRDY# 36 37 DEVSEL# +5V 38 39 GND LOCK# 40 41 SDONE# SBO# 42 43 PAR GND 44 45 V(I/O) AD[15] 46 47 AD[12] AD[11] 48 49 AD[09] +5V 50 51 GND C/BE[0]# 52 53 AD[06] AD[05] 54 55 AD[04] GND 56 57 V(I/O) AD[03] 58 59 AD[02] AD[01] 60 61 AD[00] +5V 62 63 GND REQ64# 64 Table 1-4.
1 Introduction Table 1-4. PCI Interface Connector Pinout: P12/J12, P22/J22 32-bit PCI (Continued) 1-8 Pin# Signal Name Signal Name Pin # 17 PCI-RSVD* GND 18 19 AD[30] AD[29] 20 21 GND AD[26] 22 23 AD[24] +3.3V 24 25 IDSEL AD[23] 26 27 +3.3V AD[20] 28 29 AD[18] GND 30 31 AD[16] C/BE[2]# 32 33 GND PMC-RSVD 34 35 TRDY# +3.3V 36 37 GND STOP# 38 39 PERR# GND 40 41 +3.
Connector Pinouts Table 1-5.
1 Introduction Table 1-5. PCI Interface Connector Pinout: P14/J14, P24/J24 User-Defined I/O (Continued) Pin# Signal Name Signal Name Pin # 55 I/O I/O 56 57 I/O I/O 58 59 I/O I/O 60 61 I/O I/O 62 63 I/O I/O 64 The final table, shown below, presents the last 32 bits needed to complete the 64-bit extension. Table 1-6.
Connector Pinouts Table 1-6. PCI 64-bit PCI extension on PMC Connector J13, J23 (Continued) Pin# Signal Name Signal Name Pin # 37 AD45 GND 38 39 V(I/O) AD44 40 41 AD43 AD42 42 43 AD41 GND 44 45 GND AD40 46 47 AD39 AD38 48 49 AD37 GND 50 51 GND AD36 52 53 AD35 AD34 54 55 AD33 GND 56 57 V(I/O) AD32 58 59 - - 60 61 - GND 62 63 GND - 64 http://www.motorola.
ARelated Documentation A Motorola Computer Group Documents The Motorola publications listed below offer you additional information about this product. You can obtain paper or electronic copies of Motorola Computer Group publications by: ❏ Visiting Motorola Computer Group’s Product Catalog for more information on PMC products at, http://www.motorola.com/computer/literature ❏ Contacting your local Motorola sales office ❏ Visiting Motorola Computer Group’s World Wide Web literature site, http://www.
A Related Documentation Related Specifications For additional information, refer to the following table for related specifications. As an additional help, a source for the listed document is provided. Please note that, while these sources have been verified, the information is subject to change without notice. Table A-2. Related Specifications Document Title Motorola Publication Number CompactPCI Hot Swap Specification PCI Industrial Computers Manufacturers Group (PICMG) http://www.picmg.org/ PICMG 2.
