BSR 2000 Command Reference Guide 526363-001-00 Rev. B Release 1.
Notice Copyright © 2006 Motorola, Inc. All rights reserved No part of this publication my be reproduced in any form or by any means or used to make and any derivative work (such as translation, transformation or adaptation) without written permission from Motorola, Inc. Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change.
Caring for the Environment by Recycling When you see this symbol on a Motorola product, do not dispose of the product with residential or commercial waste. Recycling your Motorola Equipment Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local authorities for information about practices established for your region.
Cuidando do meio ambiente através da reciclagem Quando você ver este símbolo em um produto Motorola, não descarte o produto junto com lixo residencial ou comercial. Reciclagem do seu equipamento Motorola Não descarte este produto junto com o lixo residencial ou comercial. Alguns países ou regiões, tais como a União Européia, criaram sistemas para colecionar e reciclar produtos eletro-eletrônicos.
Var rädd om miljön genom återvinning När du ser den här symbolen på en av Motorolas produkter ska du inte kasta produkten tillsammans med det vanliga avfallet. Återvinning av din Motorola-utrustning Kasta inte denna produkt tillsammans med det vanliga avfallet. Vissa länder eller regioner, som t.ex. EU, har satt upp ett system för insamling och återvinning av el- och elektronikavfall. Kontakta dina lokala myndigheter för information om vilka regler som gäller i din region.
Motorola Motorola , , Motorola Motorola Motorola Motorola Motorola , . Motorola . . . , Motorola .
Contents Preface Scope .......................................................................................................................................xxxiii Audience..................................................................................................................................xxxiii Documentation Set ..................................................................................................................xxxiii Conventions...................................................
BSR 2000 Command Reference Guide Release 1.0 banner motd ....................................................................................................................1-19 batch ...............................................................................................................................1-20 boot system.....................................................................................................................1-21 boot-update .................................................
Release 1.0 load-interval....................................................................................................................1-57 logging............................................................................................................................1-59 logging admin-status ......................................................................................................1-60 logging buffered ....................................................................................
BSR 2000 Command Reference Guide Release 1.0 radius-server source-interface loopback.......................................................................1-101 reload ............................................................................................................................1-102 repeat ............................................................................................................................1-103 service password-encryption ...............................................
Release 1.0 show version.................................................................................................................1-150 tacacs-server host..........................................................................................................1-153 tacacs-server key ..........................................................................................................1-155 tacacs-server port..........................................................................................
BSR 2000 Command Reference Guide Release 1.0 ip domain-name ..............................................................................................................2-23 ip forward-protocol udp..................................................................................................2-24 ip helper-address.............................................................................................................2-25 ip host ......................................................................
Release 1.0 shutdown.........................................................................................................................2-71 sntp authenticate .............................................................................................................2-72 sntp authentication-key...................................................................................................2-73 sntp broadcastdelay ......................................................................................
BSR 2000 Command Reference Guide Release 1.0 snmp-server packetsize...................................................................................................3-34 snmp-server port number................................................................................................3-35 snmp-server shutdown....................................................................................................3-36 snmp-server sysname.......................................................................
Release 1.0 debug ip pim ...................................................................................................................4-24 debug ip policy ...............................................................................................................4-26 debug ip redistribute to...................................................................................................4-27 debug ip rip..............................................................................................
BSR 2000 Command Reference Guide 6 Release 1.0 Routing Policy Commands Introduction .................................................................................................................................6-1 Routing Policy Command Descriptions ......................................................................................6-1 default-information originate............................................................................................6-2 default-metric ..........................
Release 1.0 show ip traffic.................................................................................................................6-39 show route-map ..............................................................................................................6-40 7 RIP Commands Introduction .................................................................................................................................7-1 RIP Command Descriptions.................................................
BSR 2000 Command Reference Guide Release 1.0 OSPF Command Descriptions ....................................................................................................8-1 area authentication............................................................................................................8-2 area default-cost................................................................................................................8-3 area nssa..............................................................
Release 1.0 show ip ospf interface.....................................................................................................8-39 show ip ospf memory .....................................................................................................8-41 show ip ospf neighbor ....................................................................................................8-42 show ip ospf network..................................................................................................
BSR 2000 Command Reference Guide Release 1.0 mtrace .............................................................................................................................10-9 show ip multicast cache-summary................................................................................10-10 show ip multicast fwd-cache ........................................................................................10-11 show ip multicast interface..............................................................
Release 1.0 cable flap-list percentage-threshold..............................................................................11-29 cable flap-list power-adjust threshold ..........................................................................11-30 cable flap-list size .........................................................................................................11-31 cable flap-list trap-enable .............................................................................................
BSR 2000 Command Reference Guide Release 1.0 cable ucd-interval .........................................................................................................11-70 cable upstream active-codes .........................................................................................11-71 cable upstream channel-type ........................................................................................11-72 cable upstream channel-width .............................................................
Release 1.0 cable upstream trap-enable-if .....................................................................................11-109 cable upstream trap-enable-rdn .................................................................................. 11-110 cable utilization-interval ............................................................................................. 11-111 channel-type ...............................................................................................................
BSR 2000 Command Reference Guide Release 1.0 hop threshold flap .......................................................................................................11-144 interface cable.............................................................................................................11-145 interleaver-block-size .................................................................................................11-146 interleaver-depth.............................................................
Release 1.0 show cable modem svc-flow-id..................................................................................11-204 show cable modem time-registered ............................................................................11-206 show cable modem timing-offset ...............................................................................11-209 show cable modem unregistered ................................................................................11-213 show cable modulation-profile ..
BSR 2000 Command Reference Guide Release 1.0 snr display...................................................................................................................11-261 snr loop .......................................................................................................................11-262 snr setup......................................................................................................................11-264 snr setup-get..................................................
Release 1.0 match community .........................................................................................................12-25 maximum-paths ............................................................................................................12-26 neighbor advertisement-interval...................................................................................12-27 neighbor confed-segment .............................................................................................
BSR 2000 Command Reference Guide Release 1.0 set origin .......................................................................................................................12-67 set tag............................................................................................................................12-68 set weight......................................................................................................................12-69 show ip as-path-access-list ..............................
Release 1.0 show ip pim ..................................................................................................................13-14 14 Service Class Commands Introduction ...............................................................................................................................14-1 Entering Service Class Configuration Mode..................................................................14-2 Service Class Command Descriptions ...............................................
BSR 2000 Command Reference Guide Release 1.0 trafpriority.....................................................................................................................14-34 15 Secure Shell Server Commands Introduction ...............................................................................................................................15-1 Secure Shell Server Command Descriptions ............................................................................15-1 show ssh config .............
Release 1.0 cops status-trap-enable .................................................................................................16-14 debug packet-cable gate ...............................................................................................16-15 debug packet-cable trace cops ......................................................................................16-16 debug packet-cable trace em ........................................................................................
BSR 2000 Command Reference Guide Release 1.0 show packet-cable statistics..........................................................................................16-52 spd allow-dynamic-rsp .................................................................................................16-54 spd override ..................................................................................................................16-55 spd policy.........................................................................
Preface Scope This document describes how to install and configure the Motorola™ Broadband Services Router™ 2000 (BSR 2000™). Audience This document is for use by those persons who will install and configure the BSR 2000™ product. Only trained service personnel should install, maintain, or replace the BSR 2000.
BSR 2000 Command Reference Guide ■ Release 1.0 BSR 2000 Release Notes These documents provide information about features not described or incorrectly documented in the main documentation set; known problems and anomalies; product limitations; and problem resolutions.
Release 1.0 Preface Conventions This document uses the conventions in the following table: Convention Example Explanation angle brackets < > ping ping 54.89.145.71 Arguments in italic and enclosed by angle brackets must be replaced by the text the argument represents. In the example, 54.89.345.71 replaces . When entering the argument, do not type the angle brackets. bar brackets [ ] disable [level] Bar brackets enclose optional arguments.
BSR 2000 Command Reference Guide Release 1.0 Notes, Cautions, Warnings The following icons and associated text may appear in this document. Note: A note contains tips, suggestions, and other helpful information, such as references to material not contained in the document, that can help you complete a task or understand the subject matter.
1 System Administration Commands Introduction This chapter describes the following types of commands for the BSR 2000™: User management commands which establish authentication and to protect the network from unauthorized users. Configuration file commands that handle the operating system and the system software for the BSR. The configuration file commands allow you to customize the operating system configuration at system startup, and to modify and store the configuration file for later use.
BSR 2000 Command Reference Guide Release 1.0 Logger commands which provide a way to configure system event reporting intended for diagnostics. The information in the report contains actions such as system startup, status, and event classes. System Administration Command Descriptions This section contains an alphabetized list and descriptions of the system administration commands supported by the BSR. 1-2 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands aaa accounting commands default The aaa accounting commands default command enables command use accounting on the BSR. Enabling command use accounting provides resource usage data for commands used at a specified privilege level by creating a default list of methods used for accounting services. The no aaa accounting commands command disables command use accounting.
BSR 2000 Command Reference Guide 1-4 Release 1.
Release 1.0 System Administration Commands aaa accounting exec default The aaa accounting exec default command enables terminal session accounting on the BSR. Enabling terminal session accounting provides resource usage data for a specified terminal session and creates a default list of methods used for accounting services. The no aaa accounting exec command disables terminal session accounting.
BSR 2000 Command Reference Guide 1-6 Release 1.0 wait-start sends a "start" accounting notice at the beginning of a process and a "stop" accounting notice at the end of a process - the requested user process does not begin until the "start" accounting notice is received by the server local local database to be used as the authorization method. none no method is specified as the accounting method radius RADIUS to be used as the accounting method.
Release 1.0 System Administration Commands aaa authentication enable default The aaa authentication enable default command enables AAA authentication to determine if a user can access the privilege level 15 (system administrator). The no aaa authentication enable default command disables AAA authentication. Note: If multiple authentication methods are specified, the methods are invoked in the sequence they are configured.
BSR 2000 Command Reference Guide Release 1.0 aaa authentication fail-message The aaa authentication fail-message command allows you to configure an error message to display when a TACACS login has failed. The no aaa authentication login default command disables the error message.
Release 1.0 System Administration Commands aaa authentication local-override The aaa authentication local-override command enables local authentication. This command overrides any configured default authentication method. A configured default authentication method will be used only if local authentication fails. The no aaa authentication local-override disables local authentication.
BSR 2000 Command Reference Guide Release 1.0 aaa authentication login default The aaa authentication login default command enables AAA authentication to determine if a user can login to the BSR. The no aaa authentication login default command disables AAA login authentication. Note: If multiple authentication methods are specified, the methods are invoked in the sequence they are configured.
Release 1.0 System Administration Commands aaa authorization commands default The aaa authorization commands default command enables command authorization on the BSR. Command authorization determines if a user is allowed to run commands at a specified privilege level by creating a default list of methods used for authorization services. The no aaa authorization commands default command disables command authorization.
BSR 2000 Command Reference Guide 1-12 Release 1.0 none no method is specified as the authorization method tacacs TACACS+ to be used as the authorization method MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands aaa authorization exec default The aaa authorization exec default command enables privilege level authorization on the BSR. Privilege level authorization determines if a user is allowed to run an EXEC shell (user session) by creating a default list of methods used for authorization services. The no aaa authorization exec default command disables privilege level authorization.
BSR 2000 Command Reference Guide Release 1.0 aaa console authentication The aaa console authentication command enables TACACS authentication for the console if AAA is configured. The no aaa console authentication command disables login authentication for the console. Group Access System Administrator Command Mode Global Configuration Command Line Usage aaa console authentication no aaa console authentication Command Default Enabled 1-14 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands aaa console authorization commands default The aaa console authorization commands default command enables command authorization for the console if AAA is configured. The no aaa console authorization commands default command disables command authorization for the console.
BSR 2000 Command Reference Guide Release 1.0 aaa new-model The aaa new model command enables the AAA network security model. The AAA network security model provides a software mechanism or framework for consistent authentication, authorization and accounting on the BSR. The no aaa new model disables the AAA network security model. Group Access All Command Mode Global Configuration Command Line Usage aaa new model no aaa new model Command Default Disabled 1-16 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands alias The alias command allows you to specify an alias for a CLI command in a specific command mode (User EXEC, Privileged EXEC, or Global Configuration). The no alias command deletes a specific alias defined within the command mode.
BSR 2000 Command Reference Guide Release 1.0 auto-negotiation The auto-negotiation command sets the duplex/speed configuration mode for a particular Gigabit Ethernet interface. Group Access All Command Mode Interface Configuration Command Line Usage auto-negotiation no auto-negotiation 1-18 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands banner motd The banner motd command allows you to create a message-of the-day (motd) that displays before the login prompt. The no banner motd command deletes the message of the day. Group Access All Command Mode Global Configuration Command Line Usage banner motd [<1-25>] [... ] no banner motd Command Syntax 1-25 Message of the Day line number WORD Text of the Message of the Day 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 batch The batch command executes a series of commands from a batch file stored in Flash memory or NVRAM. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage batch {flash: | nvram:} [acknowledge] Command Syntax 1-20 flash: execute a batch file from Flash memory nvram: execute a batch file from NVRAM acknowledge acknowledge the execution of each command MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands boot system The boot system command lets you boot the BSR using a boot image file stored in either Flash memory or NVRAM.
BSR 2000 Command Reference Guide Release 1.0 boot-update The boot-update command allows you upgrade the BSR boot ROM. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage boot-update Command Syntax 1-22 prefix The server IP address. string The boot image name. MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands broadcast The broadcast command is used to send a message to all connected users. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage broadcast Command Syntax WORD 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 chkdsk The chkdsk command checks for and corrects any file system errors found in files stored in Flash memory or NVRAM. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage chkdsk {flash: | nvram: } Command Syntax 1-24 flash: check the Flash memory file system nvram: check the NVRAM filesystem MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands clear evt The clear evt command resets the event count to "0" for all groups, a specified group, or specified events. Group Access All Command Mode All modes except User EXEC Command Line Usage clear evt [ | ] [] Command Syntax NUM this is always 0 for the BSR 2000 WORD the name of an EVT group - refer to Table 1-2 range specific EVTs in the specified EVT group such as '1+5+8-13'.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands clear log The clear log command deletes buffered log data. Group Access All Command Mode All modes except User EXEC Command Line Usage clear log 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clock set The clock set command sets the system clock. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage clock set {<1-31> | <1-31>} <2000-2035> Command Syntax 1-28 hh:mm:ss current time in 24-hour format 1-31 numeric notation for the current day MONTH three letter abbreviated name of the current month 2000-2035 numeric notation for the current year MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands clock timezone The clock timezone command allows you to set the time zone for the system. The no clock timezone command changes the system time to Universal Time Coordinated (UTC). Group Access System Administrator Command Mode Global Configuration Command Line Usage clock timezone [] [daylightsavings] [on | off] no clock timezone Note: The daylightsavings option has no effect on the setting of time on the BSR.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax WORD time zone listed when standard time is in effect Hours_offset hours corrected from UTC, range -23 to 23 Minute_offset non-negative difference in minutes corrected from UTC, range 0 to 59 daylightsavings configure daylight savings on | off daylight savings on or off Command Default UTC 1-30 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands configure The configure command lets you enter Global Configuration mode from Privileged EXEC mode. Note: To return to Privileged EXEC mode, enter exit, end, or Control-Z at the Global Configuration Mode prompt. Group Access All Command Mode Privileged EXEC Command Line Usage configure 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 console authentication radius The console authentication radius command enables RADIUS authentication for user console logins. The no console authentication radius command disables this feature.
Release 1.0 System Administration Commands copy The copy command copies a local or network file from one location to another, either locally or on the network.
BSR 2000 Command Reference Guide 1-34 Release 1.0 nvram: copy the configuration file to NVRAM running-config copy to the currently running system configuration startup-config copy to the startup configuration in NVRAM system: copy to the system tftp: copy the configuration file to a Trivial File Transport Protocol (TFTP) server MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands delete The delete command deletes a file stored in Flash memory or NVRAM or deletes the startup configuration file. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage delete {flash: | nvram: | startup-config} Command Syntax flash: delete all files from Flash memory nvram: delete all files from NVRAM startup-config delete the startup-configuration file 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 description The description command is used to specify descriptive information for any interface on the BSR. This information is limited to 79 characters. Use the characters: _ or - to separate words.
Release 1.0 System Administration Commands dir The dir command lists directories and files on a filesystem. Group Access All Command Mode Privileged EXEC Command Line Usage dir [all [time]] [flash: [time]] [nvram: [time]] [time] Command Syntax all list all directories and files flash: list all directories and files in flash nvram: list all directories and files in NVRAM time sort by modification time Command Default NVRAM 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 disable The disable command allows you to enter User EXEC mode from the Privileged EXEC mode. Note: To return to Privileged EXEC mode, enter enable at the User EXEC prompt and, if required, a password. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage disable 1-38 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands duplex The duplex command configures an Ethernet interface for duplex mode (full or half) and enables/disables auto-negotiation Group Access ISP Command Mode Interface Configuration (Ethernet interface only) Command Line Usage duplex {half | full | auto} no duplex {half | full | auto} Command Syntax half configures the interface for half-duplex operation. Half-duplex operation allows the interface to send and receive signals, but not at the same time.
BSR 2000 Command Reference Guide Release 1.0 enable The enable command allows you to enter Privileged EXEC mode from User EXEC mode. If the system prompts you for a password, enter the password. After entering Privileged EXEC mode, the prompt changes from the User EXEC mode prompt (hostname>) to the privileged EXEC mode prompt (hostname#). Group Access System Administrator Command Mode User EXEC Command Line Usage enable 1-40 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands enable authentication radius The enable authentication radius command enables RADIUS authentication for user logins. The no enable authentication radius command disables this feature. Group Access ISP Command Mode Global Configuration Command Line Usage enable authentication radius [ local-password ] no enable authentication radius [ local-password ] Command Syntax local-password 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 enable password The enable password command allows you to specify a password associated with the enable command. After specifying the password, entering the enable command at the User EXEC prompt causes the system to prompt you for the password. You must supply the password to enter the Privileged EXEC mode. The no enable password command deletes the password.
Release 1.0 System Administration Commands enable rdn-process This enable rdn-process command enables the process for collecting CPU utilization statistics.The no enable rdn-process command disables the collection of CPU utilization statistics. Note: This feature is enabled by default, and must remain enabled if you intend to use it in conjunction with SNMP polling of the BSR.
BSR 2000 Command Reference Guide Release 1.0 enable secret The enable secret command allows you to provide an encrypted password that supersedes the enabled password. The no enable secret command removes the secret. Use the enable secret command to provide an encrypted password for entering Privileged EXEC mode in the running configuration file when then no service password-encryption command is in effect.
Release 1.0 System Administration Commands encapsulation snap The encapsulation snap command specifies SNAP as the encapsulation method for Ethernet or Gigabit Ethernet interfaces. The SNAP encapsulation method, as specified in RFC 1042, allows Ethernet protocols to run on the IEEE 802.2 media. The no encapsulation snap command returns the interface encapsulation method to the default method which is ARPA.
BSR 2000 Command Reference Guide Release 1.0 erase The erase command erases a file system stored in Flash memory or NVRAM or the contents of the startup-configuration file. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage erase {flash: | nvram: | startup-config} Command Syntax 1-46 flash: erase all files in Flash memory nvram: erase all files in NVRAM startup-config erase the startup-configuration file MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands exit The exit command (used from the Router Configuration, Interface Configuration, and Global Configuration modes) accesses the previous command mode in the command mode hierarchy. For example: using the exit command in Interface Configuration mode accesses Global Configuration mode. Using the exit command in Privileged EXEC or User EXEC modes, ends the command line session. Group Access All Command Mode All modes Command Line Usage exit 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 format The format command formats a filesystem in flash or NVRAM. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage format {flash: | nvram:} Command Syntax 1-48 flash: format flash nvram: format NVRAM MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands help The help command displays instructions for using the CLI help functionality. Refer to the BSR 2000 Configuration and Management Guide for additional instructions on using the CLI help functionality. Group Access All Command Mode All modes Command Line Usage help 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 history size The history size command lets you specify the size of the history buffer by number of lines. The no history command deletes the history buffer. Group Access All Command Mode All modes Command Line Usage history size <1-256> no history Command Syntax 1-256 the number of lines in the history buffer Command Default 10 1-50 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands hostname The hostname command configures the name for the system host. Group Access System Administrator Command Mode Global Configuration Command Line Usage hostname Command Syntax WORD 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip ftp password The ip ftp password command displays the password to use to connect to the network using FTP. The no ip ftp password command deletes the password for an FTP connection.
Release 1.0 System Administration Commands ip ftp username The ip ftp username command configures the connection to the network for using FTP. The no ip ftp username command configures the router anonymously for FTP. Use the ip ftp username command that is related to an account on the server. Group Access System Administrator Command Mode Global Configuration Command Line Usage ip ftp username no ip ftp username Command Syntax WORD 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip netmask-format The ip netmask-format command lets you specify the format in which netmask values appear in show command output. The no ip netmask format command sets the output format back to the default.
Release 1.0 System Administration Commands ip tacacs source-interface The ip tacacs source-interface command allows an operator to control the source IP address of TACACS+ packets generated by the BSR by specifying an Ethernet or loopback interface as the source IP address for TACACS+ packets. The normal convention for generated TACACS+ packets is to set the source IP address equal to the IP address of the outgoing interface.
BSR 2000 Command Reference Guide Release 1.0 ip tftp source-interface loopback The ip tftp source-interface loopback command allows an operator to control the source IP address of TFTP packets generated by the BSR by specifying a loopback interface as the source IP address for TFTP packets. The normal convention for generated TFTP packets is to set the source IP address equal to the IP address of the outgoing interface.
Release 1.0 System Administration Commands load-interval The load-interval command specifies the load interval timer value in minutes. The load interval timer captures bandwidth utilization information on a per-port basis for both received and transmitted data. Bandwidth utilization information can then be displayed with the show interfaces command.
BSR 2000 Command Reference Guide 1-300 Release 1.0 the load interval timer value in minutes Command Default 5 minutes 1-58 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands logging The logging command specifies the IP address of a remote SYSLOG server. The no logging command clears the IP address specification of a remote SYSLOG server. Group Access All Command Mode Global Configuration Command Line Usage logging no logging Command Syntax A.B.C.D. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 logging admin-status The logging admin-status command controls the transmission of traps and SYSLOG messages with respect to the threshold specified with the logging rate-limit command. The logging admin-status command is only relevant if DOCSIS logging control has been specified with the logging control docsis command. In CLI logging control mode, the logging admin-status command will be ignored by the system and a warning message will display if it is used.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 logging buffered The logging buffered command sets the size of the logging buffer and the severity level. The no logging buffered command returns to the default buffer size (256 KB). Note: Use the show log command, in Privileged EXEC mode, to display logged messages with the newest message displayed first.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 logging console The logging console command enables the sending of system logging messages to the console. Additionally, the logging of messages displayed on the console terminal can be limited to a specified severity level. Use the no logging console command to disable console logging.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 logging control docsis The logging control docsis command allows the DOCSIS docsDevEvControlTable to determine which severity logs go to which destinations. Note: Any of the various logging commands in place are overridden with this command. The no logging control docsis disables the docsDevEvControlTable and re-establishes CLI logging control.
Release 1.0 System Administration Commands logging default The logging default command restores the default settings for all logging, including logging , logging reporting, and EVT configurations. ■ The docsDevEvControlTable is restored to its DOCSIS-specified default values. ■ CLI logging control is re-established. ■ All logging evt configuration lines are removed from the running configuration file. ■ Any logging (for SYSLOG server) commands are unaffected.
BSR 2000 Command Reference Guide Release 1.0 logging disable bpi_auth_invalid_messages The logging disable bpi_auth_invalid_messages command disables logging of the "BPI authorization invalid" DOCSIS error message. The no logging disable bpi_auth_invalid_messages enables the logging of this error message. This command is useful in situations where a high volume of this error message is being generated and logged.
Release 1.0 System Administration Commands logging disable bpi_auth_reject_messages The logging disable bpi_auth_reject_messages command disables logging of the "BPI authorization reject" DOCSIS error message. The no logging disable bpi_auth_reject_messages enables the logging of this error message. This command is useful in situations where a high volume of this error message is being generated and logged.
BSR 2000 Command Reference Guide Release 1.0 logging disable bpi_map_reject_messages The logging disable bpi_map_reject_messages command disables logging of the Map Reject DOCSIS error messages. The no logging disable bpi_map_reject_messages command enables the logging of Map Reject error messages. This command is useful in situations where large numbers of these error messages are being generated and logged.
Release 1.0 System Administration Commands logging disable cm_ranging_fail_r103_0 The logging disable cm_ranging_fail_r103_0 command disables logging of the "Unable to Successfully Range CM Retries Exhausted" DOCSIS error message. The no logging disable cm_ranging_fail_r103_0 enables the logging of this error message. This command is useful in situations where a high volume of this error message is being generated and logged.
BSR 2000 Command Reference Guide Release 1.0 logging evt clear The logging evt clear command disables logging of all EVTs or disables EVT logging for a specific logging destination (s). The no logging evt clear command restores the default EVT logging configuration.
Release 1.0 System Administration Commands logging evt set The logging evt set command configures EVT logging to log messages to a different destination. The EVT messages logged can also be configured on a per-slot, per group, or single, per-event basis. The no logging evt set command with no specified EVT group name restores the original logging configuration changed with one or more logging evt set commands.
BSR 2000 Command Reference Guide Release 1.0 logging facility The logging facility command specifies the SYSLOG facility to which error messages are sent. The no logging facility command reverts to the default of "local7".
Release 1.0 System Administration Commands logging on The logging on command starts and stops the SYSLOG, and sends debug and error messages to a logging process. The no logging on command stops sending debug or error messages to a logging process. Group Access All Command Mode Global Configuration Command Line Usage logging on no logging on Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 logging rate-limit The logging rate-limit command limits the rate of system messages and SNMP traps logged per second. The no logging rate-limit command disables the rate limit.
Release 1.0 System Administration Commands logging reporting The logging reporting command specifies the recording mechanism for logging reports.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands all-clear unsets all logging locations for the report. all-set sets all logging locations for the report. Note: Debug messages will not be reported unless debugging has been turned on for a subsystem with the corresponding CLI debug command (e.g. debug snmp). 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 logging reporting default The logging reporting default command is used to return to the default destination/ severity log reporting configuration. Note: The default destination/severity log reporting configuration depends on which logging control mode is enabled. Group Access All Command Mode Global Configuration Command Line Usage logging reporting default 1-80 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands logging session The logging session command enables the transmission of system logging messages to the current login session. The no logging session command disables the transmission of system logging messages to the current login session. Group Access All Command Mode Privileged EXEC Command Line Usage logging session no logging session 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 logging snmp-trap The logging snmp-trap command logs all SNMP traps or logs SNMP traps of a specified severity level and higher. Note: The logging snmp-trap command limits SNMP trap logging to SNMP traps with a level up to and including the severity level specified with this command.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 logging source-interface loopback The logging source-interface loopback command allows an operator to control the source IP address of SYSLOG packets generated by the BSR by specifying a loopback interface as the source IP address for SYSLOG packets. The normal convention for generated SYSLOG packets is to set the source IP address equal to the IP address of the outgoing interface.
Release 1.0 System Administration Commands logging trap The logging trap command filters messages logged to the SYSLOG servers based on severity. The command limits the log messages sent to a SYSLOG server to messages with a severity level up to and including the severity level specified with this command. The no logging trap command disables the logging of these messages to the SYSLOG servers.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands login The login command logs a user on to the system. Group Access All Command Mode User EXEC Command Line Usage login [] Command Syntax WORD 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 logout The logout command logs a user out of the system. Use the logout command to end the current session. The logout command is used the same way as the exit command. In Privileged EXEC mode, use the logout command with a character argument to log a particular user out of the system. Only users with administrative privileges can log other users out.
Release 1.0 System Administration Commands macro The macro command defines a group of existing CLI commands that can be executed by entering the macro name at the command line. The no macro command removes a macro from the macro list. Group Access All Command Mode All modes except User EXEC and Privileged EXEC Command Line Usage macro {Variable | } ...
BSR 2000 Command Reference Guide Release 1.0 memory checkzero The memory checkzero command enables memory checking on the BSR. Note: Memory checking can use considerable BSR system resources. Group Access All Command Mode All modes except User EXEC Command Line Usage memory checkzero <0-1> Command Syntax 0-1 1-90 1 = enable Memory Checking 0 = disable Memory Checking MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands message The message command sends a message to a specified active user. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage message Command Syntax WORD session number or username WORD message to send 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 more The more command displays the contents of a specified file. Use the more nvram:startup-config command to view the startup configuration file in NVRAM. The config_file environmental table will be displayed if the startup configuration file is not displayed. The user can determine the status of the file which is either a complete or a distilled version of the configuration file.
Release 1.0 System Administration Commands include filter for output that includes the specified string WORD the specified string 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 network-clock-select bits e1 The network-clock-select bits e1 command configures the BITS (network) clock. The no network-clock-select bits command deletes the network clock configuration and put the BITS clock in Free-run mode.
Release 1.0 System Administration Commands network-clock-select bits t1 The network-clock-select bits t1 command configures the BITS (network) clock. The no network-clock-select bits command deletes the network clock configuration and put the BITS clock in Free-run mode.
BSR 2000 Command Reference Guide Release 1.0 page The page command controls the scrolling of system output displays. Group Access All Command Mode All modes Command Line Usage page {off | on} Command Syntax off scrolling continues until the end of the display without stopping on controlled scrolling through the use of the Enter/Return key and spacebar Command Default on 1-96 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands password The password command establishes a password that must be specified by users attempting to establish a console or telnet session with the BSR. A console or telnet session will not be established if the correct password is not specified by the user. The no password command removes the password.
BSR 2000 Command Reference Guide Release 1.0 privilege restricted The privilege restricted command designates a specific CLI command or group of commands as belonging to the "restricted" user group. Only users in the "restricted" user group have read-write access to commands designated as "restricted". Note: By default, users in the "restricted" user group will not be able to execute any commands unless they have been specified as "restricted" with the privilege restricted command.
Release 1.0 System Administration Commands radius-server The radius-server command configures a RADIUS client to allow communication with a RADIUS server.
BSR 2000 Command Reference Guide 1-100 Release 1.
Release 1.0 System Administration Commands radius-server source-interface loopback The radius-server source-interface loopback command allows an operator to control the source IP address of Radius authentication protocol packets generated by the BSR by specifying a loopback interface as the source IP address for Radius authentication protocol packets.
BSR 2000 Command Reference Guide Release 1.0 reload The reload command reloads the operating system. The reload command is most often used to reload upgraded software.
Release 1.0 System Administration Commands repeat The repeat command repeats a command or series of commands Group Access All Command Mode Privileged EXEC Command Line Usage repeat {} { [...] | delay { [...]}} Command Syntax NUM the number of times to repeat the command or series of commands WORD the command or series of commands delay NUM the delay (in seconds) between the execution of each command 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 service password-encryption The service password-encryption command enables password encryption. The no service password-encryption disables password encryption. The service password-encryption command will also encrypt previously specified passwords in the running-config file that are currently unencrypted.
Release 1.0 System Administration Commands session-timeout The session-timeout command lets you specify the length of time (in minutes) before the BSR terminates any inactive session. An inactive session is a session has received no user input or system output during the specified time interval.
BSR 2000 Command Reference Guide Release 1.0 session-window set The session-window set command specifies the height and width parameters of the current CLI session window. Group Access All Command Mode All modes except User EXEC Command Line Usage session-window set {height <4-128> | width <16-384>} Command Syntax 1-106 height 4-128 sets window height in number of lines width 16-384 sets window width in number of columns MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show aliases The show aliases command displays any one of the following: ■ Aliases for commands in all modes ■ Aliases for commands in a specific mode. ■ Aliases for all commands that begin with, include, or exclude a specified string. ■ Aliases for a specific mode that begin with, include, or exclude a specified string.
BSR 2000 Command Reference Guide 1-108 Release 1.0 include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show boot The show boot command lists the boot parameters. Use the show boot command to display the contents of the BOOT environment variables and the configuration register setting.
BSR 2000 Command Reference Guide Release 1.0 show clock The show clock command shows the system clock.
Release 1.0 System Administration Commands show evt The show evt command displays EVT counts for all EVT groups, a specific EVT group, EVT group counts that only occur on a specific BSR slot, or individual event. By default, only EVT groups with non-zero event counts are displayed.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands Command Syntax NUM this is always 0 for the BSR 2000 WORD the name of an EVT group - refer to Table 1-2 range specific EVTs in the specified EVT group such as '1+5+8-13'. An asterisk "*" displays all EVTs (including EVTs with a count of "0") for a specific EVT group or individual EVT. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands show history The show history command displays a list of commands executed during a session. The list size is determined by the setting of the history size command.
BSR 2000 Command Reference Guide Release 1.0 show log The show log command displays message logging in the log file the newest message first.The show log command displays log file contents and information about users who have logged into the BSR. The following is an example of typical screen output from the show log command: Preparing log file for reading ... [02/11-10:39:08- 07:telnet01]-N-user enabled-user authenticated [02/11-10:39:04- 07:telnet01]-N-connection made from 10.14.11.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 show logging evt The show logging evt command displays the EVT configuration entries in the running configuration file. The following is an example of typical screen output from the show logging evt command: EVT RUNNING logging evt logging evt logging evt CONFIG: set c drme 82 set c rdb 197 set c dra 121 Group Access All Command Mode All modes except User EXEC Command Line Usage show logging evt 1-118 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show logging reporting The show logging reporting command displays the recording mechanism for logging messages based on their severity level. The display output is in the format: logging reporting e.g. logging reporting alert local.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands Group Access All Command Mode All modes except User EXEC Command Line Usage show logging reporting 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show logging syslog The show logging syslog command displays a counter of the total number of log messages sent to the SYSLOG server and the number of messages dropped if a logging threshold has been exceeded.
Release 1.0 System Administration Commands show macro The show macro command lists all configured macros on the BSR.
BSR 2000 Command Reference Guide Release 1.0 show memory The show memory command displays the memory content of the starting address. Use the show memory command to view information about memory available after the system image decompresses and loads.
Release 1.0 System Administration Commands begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output Command Default 32 bit 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show network-clocks The show network-clocks command displays the current BITS clock state and alarms. Group Access All Command Mode All modes except User EXEC Command Line Usage show network-clocks 1-126 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show pool The show pool command displays information on data buffering including all memory buffer pools, application-specific pools, the network pool, system physical structures, and all mBuf pool names.
BSR 2000 Command Reference Guide 1-128 Release 1.0 exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show process The show process command displays information about software processes that are running on the router.
BSR 2000 Command Reference Guide 1-130 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show process cpu The show process cpu command displays detailed CPU usage statistics for the BSR 2000. The module type (for example: 1x4 CMTS slot ) is displayed along with the CPU usage statistics for that module. For HSIM modules, the module sub type (for example: Sub Type: SMGE) is displayed.
BSR 2000 Command Reference Guide Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output Command Default frequency = 60 Hz 1-132 MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands show process memory The show process memory command displays per process memory usage information about software processes that are running on the BSR.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 show process msg-q-info The show process msg-q-info command displays information about current message queues.
Release 1.0 System Administration Commands show process semaphores The show process semaphores command creates a message when an attempt to unlock a semaphore when it is already unlocked.
BSR 2000 Command Reference Guide Release 1.0 show process stack The show process stack command monitors the stack utilization of processes and interrupt routines.
Release 1.0 System Administration Commands show reload The show reload command displays the status of a Hitless Upgrade in progress after a software reload of all modules in the BSR chassis has been initiated with the reload switched command. Group Access All Command Mode All modes except User EXEC Command Line Usage show reload 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show running-config The show running-config command displays configuration information currently running on the BSR.
Release 1.0 System Administration Commands | turns on output modifiers (filters) begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show startup-config The show startup-config command displays the contents of the system startup configuration file.
Release 1.0 System Administration Commands show stats summary error The show stats summary error command displays FEC error counts and ratios. The following is an example of typical screen output from the show stats summary error command: MAC Address 0008.0e16.e6e2 0008.0e16.f954 00e0.0c60.02b4 I/F 0/0/U1 0/0/U1 0/0/U1 SID 2 1 3 CorrFec Count 0 0 0 CorrFec Ratio 0.00000000 0.00000000 0.00000000 UnCorrFec Count 0 0 0 UnCorrFec Ratio 0.00000000 0.00000000 0.
BSR 2000 Command Reference Guide Release 1.0 show tacacs The show tacacs command displays statistics for all TACACS+ servers on the network including the IP address of the servers, connections, failed connection attempts, and packets sent and received. If there is more than one TACACS+ server configured, the command output displays statistics for all servers in the order in which they were configured. The following is an example of typical screen output from the show tacacs command: Tacacs+ Server : 11.
Release 1.0 System Administration Commands show tacacs statistics The show tacacs statistics command displays overall TACACS+ statistics including the total number of access (AAA) requests, the number of denied requests, and the number of allowed requests.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 System Administration Commands Command Line Usage show tech [flash: | nvram:] Command Syntax flash: output to a file on the Flash memory file system nvram: output to a file on the NVRAM file system 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show user-group The show user-group command displays the group access level for a specific CLI command.
Release 1.0 System Administration Commands show users The show users command displays information about active Telnet sessions including the username, user group and privilege level, the IP address of the originating host, and the session ID.
BSR 2000 Command Reference Guide Release 1.0 show version The show version command displays the configuration of the system hardware, the software version, the names and sources of configuration files, and the boot images.
Release 1.0 System Administration Commands Command Syntax | turns on output modifiers (filters) begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 speed The speed command specifies the speed at which the Ethernet interface operates. The default speed is auto-negotiated but the speed can be manually set to either 10 Mbps or 100 Mbps.
Release 1.0 System Administration Commands tacacs-server host The tacacs-server host command is used to specify and configure individual TACACS+ servers. The command can also be used to configure multiple TACACS+ servers. The TACACS+ client will contact the servers in the order in which they are specified.The no tacacs-server host command removes a TACACS+ server from the list.
BSR 2000 Command Reference Guide 1-154 Release 1.0 retry 0-100 specifies a retry value - this value overrides the global retry value set with the tacacs-server retry command for this TACACS+ server only single-connection opens a new TCP connection for every TACACS session established timeout 1-1000 specifies a timeout value in seconds - this value overrides the global timeout value set with the tacacs-server timeout command for this TACACS+ server only MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands tacacs-server key The tacacs-server key command is used to specify a global authentication encryption key used for all TACACS+ communications between the TACACS+ client and the TACACS+ server. A global encryption key is used if no encryption key is specifically configured for this TACACS+ server. The no tacacs-server key disables authentication encryption. Note: The key entered must match the key used on the TACACS+ server.
BSR 2000 Command Reference Guide Release 1.0 tacacs-server port The tacacs-server port command to specify a global port number for all communication between the TACACS+ server and the TACACS client. A global port number is used if no port number is specifically configured for this TACACS+ server. The no tacacs-server port command restores the default port number value of 49.
Release 1.0 System Administration Commands tacacs reset-connections The tacacs reset-connections command is used to reset all the TACACS+ server connections and associated sessions. After reset, all connections will be re-established. The tacacs reset-connections command is useful to initiate a reset and re-establish the existing connections after making any connection-specific configuration changes.
BSR 2000 Command Reference Guide Release 1.0 tacacs-server retry The tacacs-server retry command is used to globally specify a retry count for all TACACS+ servers. A global retry count is used if no retry count is specifically configured for this TACACS+ server. The no tacacs-server retry command restores the global default value of 3 retries.
Release 1.0 System Administration Commands tacacs-server timeout The tacacs-server timeout command is used to specify a global timeout interval for all TACACS+ servers. A global timeout value is used if no timeout value is specifically configured for this TACACS+ server. The no tacacs-server timeout command restores the global default timeout value or specifies another value.
BSR 2000 Command Reference Guide Release 1.0 telnet The telnet command establishes a telnet connection between the BSR and a remote system. Group Access All Command Mode Privileged EXEC Command Line Usage telnet { | } Command Syntax 1-160 A.B.C.D the IP address of a remote system WORD the hostname of a remote system MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands telnet authentication radius The telnet authentication radius command enables RADIUS authentication for telnet access. The no telnet authentication radius command disables this feature.
BSR 2000 Command Reference Guide Release 1.0 telnet session-limit The telnet session-limit command specifies a limit on the number of concurrent telnet sessions allowed to the BSR. Setting the session-limit to "0" will disallow any telnet sessions from being accepted. Setting a session-limit value will not affect any currently open telnet sessions. The no telnet session-limit command restores the default session limit of 64 concurrent telnet sessions.
Release 1.0 System Administration Commands update-fpga The update-fpga command allows you upgrade the BSR FPGA. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage update-fpga Command Syntax prefix The server IP address. string The FPGA image name. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 username The username command establishes a login authentication system based on a username.
Release 1.0 System Administration Commands Note: Refer to Defining a User Name with an Encrypted Password in the BSR 2000 Configuration and Management Guide for Release 3.1 for details on encrypting passwords. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 username privilege The username privilege command sets a privilege level for a user. Group Access System Administrator Command Mode Global Configuration Command Line Usage username privilege {ro | rw} Command Syntax 1-166 WORD the username, up to 16 characters privilege the user privilege level ro read-only privilege rw read and write privilege MGBI 526363-001-00 Rev.
Release 1.0 System Administration Commands username user-group The username user-group command assigns a user to a user group. The no username user-group command removes a user from a user group.
2 IP Commands Introduction This chapter describes the following types of commands for the BSR: Interface commands not associated with a specific protocol can be used to configure interface features with any device on the network. Transmission Control Protocol/Internet Protocol (TCP/IP) commands handle network communications between network nodes. This includes network addressing information, control information that enables packets to be routed, and reliable transmission of data.
BSR 2000 Command Reference Guide Release 1.0 Tunneling commands provide a way to encapsulate packets inside of a transport protocol. IP in IP Encapsulation for tunnel interfaces is supported by the BSR. IP Command Descriptions This section contains an alphabetized list and descriptions of the IP commands supported by the BSR. 2-2 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands arp The arp command adds a permanent entry in the ARP cache. The no arp command removes the entry in the ARP cache. The arp command can also specify the type of ARP packet that is used, whether to use an alias if proxy arp is enabled, and to specify a cable bundle interface if cable bundling is being used. Note: Proxy ARP is not enabled by default. ARP cache entries translate 32-bit addresses into 48-bit hardware addresses.
BSR 2000 Command Reference Guide Release 1.0 arp timeout The ARP timeout feature is used to prevent unnecessary flooding of traffic over the cable network. ARP resolution requests are terminated after a defined interval when attempts to resolve addressing information, for a device entry in the ARP cache table. The ARP cache table expiration value is disabled by default. The arp timeout command configures the amount of time an entry stays in the ARP cache.
Release 1.0 IP Commands cable helper-address The cable helper address function disassembles a DHCP broadcast packet, and reassembles it into a unicast packet so that the packet can traverse the router and communicate with the DHCP server. The cable helper-address command enables broadcast forwarding for User Datagram Protocol (UDP) packets. The cable helper-address command is also used to bind a cable helper address to a secondary IP subnet of a CM which is connected to CPEs belonging to a particular ISP.
BSR 2000 Command Reference Guide 2-6 Release 1.0 mta specifies that only CPE MTA broadcasts are forwarded. isp-bind A.B.C.D specifies the secondary IP subnet to which the cable-helper is bound. MGBI 526363-001-00 Rev.
Release 1.0 IP Commands clear arp-cache The clear arp-cache command clears dynamic entries from ARP cache. Group Access ISP Command Mode Privileged EXEC Command Line Usage clear arp-cache [] Command Syntax A.B.C.D 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear counters The clear counters command is used to clear a specific counter or all interface counters.
Release 1.0 IP Commands clear host The clear host command deletes DNS host entries from the host-name-and-address cache. Group Access ISP Command Mode Privileged EXEC Command Line Usage clear host { | *} Command Syntax WORD deletes a specific DNS host entry * deletes all DNS host entries 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear ip route The clear ip route command deletes route table entries. Group Access ISP Command Mode Privileged EXEC Command Line Usage clear ip route {* | []} Command Syntax 2-10 * Deletes all routes. A.B.C.D Destination network IP address. A.B.C.D Destination network subnet mask. MGBI 526363-001-00 Rev.
Release 1.0 IP Commands clear ip traffic The clear ip traffic command resets the IP traffic statistic counters to zero. Group Access ISP Command Mode Privileged EXEC Command Line Usage clear ip traffic 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 host authorization The host authorization feature is used for security purposes on the cable network. When enabled, host authorization denies access to any hacker who tries to take or “spoof” an IP address from any legitimate user on the same cable network. A hacker takes the IP address from this user to steal their data service.
Release 1.0 IP Commands cpr specify a customer premise router on enable host authorization Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 interface The interface command specifies an interface for further configuration. Once the interface is selected you enter Interface configuration mode. Group Access ISP Command Mode Global Configuration Command Line Usage interface {cable | ethernet | gigaether | loopback <1-64>} Command Syntax 2-14 cable X/Y CMTS that provides 1 downstream channel and 4 upstream channels. Commonly referred to as the cable interface.
Release 1.0 IP Commands ip access-group The ip access-group command configures an interface to use an access list. The no ip access-group command does not allow incoming or outgoing packets. Group Access ISP Command Mode Interface Configuration Command Line Usage ip access-group {<1-199> <1300-2699> {in | out} no ip access-group {<1-199> <1300-2699> {in | out} Command Syntax 1-199 Standard number range from 1 to 199. 1300-2699 Extended number range from 1300 to 2699.
BSR 2000 Command Reference Guide Release 1.0 ip address The ip address command configures a primary or secondary IP address for an interface or defines the Gateway IP address (giaddr) for Customer Premises Equipment (CPE), Multimedia Telephone Adapter (MTA), or cable modem DHCP requests. The no ip address command is used to remove an IP address from the interface. When configuring the cable interface IP address two additional options are supported; the host and mta options.
Release 1.0 IP Commands Command Mode Interface Configuration (cable or loopback interfaces only) Command Line Usage ip address [ secondary [ host | mta ][isp-bind ]]] no ip address [ secondary [ host | mta ][isp-bind ]]] Command Syntax A.B.C.D the IP address A.B.C.
BSR 2000 Command Reference Guide Release 1.0 ip broadcast-address The ip broadcast-address command creates a broadcast address for an interface. The no ip broadcast-address command deletes the broadcast address for an interface. Group Access ISP Command Mode Interface Configuration Command Line Usage ip broadcast-address no ip broadcast-address Command Syntax A.B.C.D 2-18 broadcast IP address assigned to the interface MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip dhcp relay information The ip dhcp relay information command enables the BSR to insert DHCP relay information option (option-82) into received DHCP client messages being forwarded to a DHCP server (configured using the cable helper command).
BSR 2000 Command Reference Guide Release 1.0 Command Syntax 2-20 option insert a MAC address (Agent Remote ID) only into a client’s DHCP discover packets spectrum-group-name insert the Spectrum Group name into all DHCP outbound requests MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip domain-list The ip domain-list command provides up to six domain names to resolve unqualified host names when the primary domain, specified by the ip domain-name command, fails to resolve. Use the ip domain-list command to define a list of secondary domain names. Secondary domain names are used if the primary domain name fails to resolve.
BSR 2000 Command Reference Guide Release 1.0 ip domain-lookup The ip domain-lookup command enables the IP Domain Name System (DNS) based host name-to-address translation. The no ip domain-lookup command disables the IP DNS-based name-to-address translation. Group Access ISP Command Mode Global Configuration Command Line Usage ip domain-lookup no ip domain-lookup Command Default Enabled 2-22 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip domain-name For each BSR, you should configure the name of the domain in which the BSR is located. This is the default domain name that is appended to host names that are not fully qualified. The ip domain-name command is used to configure a domain name. The no ip domain-name command removes the domain name.
BSR 2000 Command Reference Guide Release 1.0 ip forward-protocol udp The ip forward-protocol udp command controls what type of UDP packet to forward when broadcasting packets or allows all types of UDP packets to be forwarded. The no ip forward-protocol udp command disables IP forwarding.
Release 1.0 IP Commands ip helper-address The ip helper-address command determines the destination IP address of the DHCP server for where broadcast packets are forwarded. The no ip helper-address command removes the IP address where broadcast packets are forwarded. Use the ip-helper address command to forward broadcast packets received on an interface. Group Access ISP Command Mode Interface Configuration Command Line Usage ip helper-address no ip helper-address Command Syntax A.
BSR 2000 Command Reference Guide Release 1.0 ip host The ip host command is used to add a static, classless DNS host entry to the ip hostname table by matching the host IP address to its DNS host name mapping. The no ip host command deletes the host address-to-name mapping in the host cache. Note: The initial character of the name must be a letter. Group Access ISP Command Mode Global Configuration Command Line Usage ip host no ip host
Release 1.0 IP Commands ip irdp The ip irdp command enables the ICMP Router Discovery Protocol (IRDP) on an interface. The no ip irdp command disables the ICMP IRDP on an interface. Group Access ISP Command Mode Interface Configuration (Ethernet and Gigabit Ethernet interfaces only) Command Line Usage ip irdp [address | holdtime <1-9000> | maxadvertinterval <4-1800> | minadvertinterval <3-1800> | multicast | preference <-2147483648-2147483647>] no ip irdp [address
BSR 2000 Command Reference Guide Release 1.0 preference preference value for this interface, -231 to 231, higher value increases performance, preferred router -2147483648-2147483647 preference for this address (higher values preferred) Command Default holdtime 2-28 = 1800 seconds maxadvertinterval = 600 seconds minadvertinterval = 450 seconds preference -2147483648-2147483647 = MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip mask-reply The ip mask-reply command enables Internet Control Message Protocol (ICMP) netmask reply messages. The no ip mask-reply command disables ICMP netmask reply messages. Group Access ISP Command Mode Interface Configuration Command Mode ip mask-reply no ip mask-reply Command Default Enabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip mtu The ip mtu command configures the Maximum Transmission Unit (MTU) packet size allowed on the interface. The no ip mtu command resets the default. Group Access ISP Command Mode Interface Configuration Command Line Usage ip mtu <68-4000> no ip mtu Command Syntax 68-4000 MTU size in bytes Command Default 1496 bytes 2-30 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip name-server The ip name-server command is used to enter the IP address of one or more Domain Name Servers (DNS). Up to six DNS can be configured on the BSR. The no ip name-server command deletes a DNS entry. Group Access ISP Command Mode Global Configuration Command Line Usage ip name-server [<...A.B.C.D>] no ip name-server [<...A.B.C.D>] Command Syntax A.B.C.D 526363-001-00 Rev. B IP addresses of your DNS.
BSR 2000 Command Reference Guide Release 1.0 ip proxy-arp The ip proxy-arp command enables proxy ARP on the interface. The no ip proxy-arp command disables proxy ARP on an interface. Note: If a host in the local network is incapable of responding to an ARP request for some reason, the router will respond on behalf of the host when proxy arp is enabled and the IP-to-MAC address mapping of the host is stored in the router with a static arp command, with the alias option specified.
Release 1.0 IP Commands ip rarp-server The ip rarp-server command is used to enable the router to act as a RARP server. The no ip rarp-server command disables the router to act as a RARP server. The RARP server can be configured on each interface to ensure that the router does not affect RARP traffic on other subnetworks that do not need RARP assistance.
BSR 2000 Command Reference Guide Release 1.0 ip redirects The ip redirects command enables messages to be redirected if a packet needs to be resent through the interface that received the packet. The no ip redirects command disables messages that are redirected if a packet needs to be resent through the interface that received the packet.
Release 1.0 IP Commands ip route The ip route command is used to configure a static route when the router cannot dynamically build a route to the specific destination or if the route must be in place permanently. The no ip route command remove a static route. Group Access ISP Command Mode Global Configuration Command Line Usage ip route { | null <0-0>} [<1-255> | [tag <1-4294967295>] no ip route {
BSR 2000 Command Reference Guide Release 1.0 ip routing The ip routing command enables IP routing. The no ip routing command disables IP routing. Group Access ISP Command Mode Global Configuration Command Line Usage ip routing no ip routing Command Default Enabled 2-36 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands ip source-route The ip source-route command allows the BSR to handle IP datagrams with source routing header options. The no ip source-route command discards any IP datagram containing a source-route option. Group Access ISP Command Mode Global Configuration Command Line Usage ip source-route no ip source-route 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip unreachables The ip unreachables command enables processing of an ICMP unreachable message when the BSR cannot deliver a received packet. The no ip unreachables command disables ICMP unreachable message processing when the router cannot deliver a received a packet. Group Access ISP Command Mode Interface Configuration and Global Configuration Command Line Usage ip unreachables no ip unreachables Command Default Enabled 2-38 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands passive-interface The passive-interface command suppresses routing updates from being transmitted over a specific ethernet or cable routing interface. The no passive-interface re-enables route updates to be transmitted over the routing interface. Note: Updates from routers that are directly connected to the passive interface continue to be received and processed.
BSR 2000 Command Reference Guide Release 1.0 ping The Packet Internet Groper (PING) ping command sends an Internet Control Message Protocol (ICMP) echo request to a remote host that reports errors and provides information relevant to IP packet addressing. Use the ping command to check host reach ability and network connectivity, or to confirm basic network connectivity. Note: The address of the source in an echo message will be the destination of the echo reply message.
Release 1.0 IP Commands 1-65535 number of ping requests to send timeout 1-1024 timeout in seconds source A.B.C.D source IP address to use to send the ping request tos 0-255 the type of service of the ping packets ttl 0-255 Time to live value in seconds df sets the "don’t fragment" IP flag in the outgoing ping IP header docsis DOCSIS-complaint cable modem mac The cable modem mac address in the form of xxxx.xxxx.
BSR 2000 Command Reference Guide Release 1.0 show arp The show arp command displays static and dynamic entries in the ARP table. The following is typical screen output from the show arp command: Protocol Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Internet Address Age(min) 10.10.10.10 10.255.4.1 10.255.5.1 10.255.6.1 10.255.7.1 150.31.60.1 41 150.31.60.10 150.31.60.99 150.31.61.23 21 150.31.61.27 31 150.31.61.
Release 1.0 IP Commands exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show controllers The show controllers command displays detailed hardware and configuration information for each module on installed in the BSR chassis.
Release 1.0 IP Commands mac display MAC layer (layer 2) information for all cable modems on this specific CMTS module upstream 0-3 display information for an upstream port including the upstream modulation type, channel width, frequency, and modulation profile information (i.e minislots, interleave, preamble, etc.
BSR 2000 Command Reference Guide Release 1.0 show host authorization The show host authorization command displays the host authorization enabled state and displays all cable host entries in the ARP authorization table. The following screen output is displayed: Device Host Modem Host Modem Type Dyn Dyn Dyn Dyn State Ack Ack-TD-TF Ack Ack-TD-TF Seconds 90000 90000 90000 90000 Modem MAC Addr 0008.0e72.bf70 0008.0e72.bf70 0008.0e73.1dba 0008.0e73.1dba Host IP Addr 150.31.43.3 150.31.42.2 150.31.43.
Release 1.0 IP Commands show host authorization cpe The show host authorization cpe command is used to display the dynamic or static ARP entries for CPEs only. The following screen output is displayed: Type Dynamic Dynamic Host IP Address 150.31.43.3 150.31.43.2 Host MAC Address 0008.0e72.bf72 0008.0e73.
BSR 2000 Command Reference Guide 2-48 Release 1.0 WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 IP Commands show host authorization summary The show host authorization summary command is used to display the dynamic or static ARP entries for CPEs only.
BSR 2000 Command Reference Guide 2-50 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 IP Commands show host unauthorized cpe The show host unauthorized cpe command displays the list of hosts/CPEs that are unauthorized due to a failed DHCP lease query response. Group Access All Command Mode All modes except User EXEC Command Line Usage show host unauthorized cpe 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show hosts The show hosts command displays the cache list of host names and addresses, and the lookup service type. Group Access ISP Command Mode Privileged EXEC Command Line Usage show hosts 2-52 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands show interfaces Use the show interfaces command to display the status and statistics for the network interfaces. Use the show interfaces command without the slot and interface argument to display all interfaces.
BSR 2000 Command Reference Guide 2-54 Release 1.0 include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 IP Commands show ip arp The show ip arp command displays the Internet Protocol (IP) Address Resolution Protocol (ARP) cache table entries for individual interfaces or all interfaces on the BSR. Each ARP entry describes the protocol type, IP address to MAC address binding, age time, ARP type, and interface location and type. Use the additional command arguments to filter the output information you want to receive.
BSR 2000 Command Reference Guide 2-56 Release 1.0 begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 IP Commands show ip dhcp stats The show ip dhcp stats command displays DHCP server statistical information. including memory usage, counters, and DHCP messages sent and received for a specified slot or all slots on the BSR. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip dhcp stats [] Command Syntax NUM 526363-001-00 Rev. B This is always 0 for the BSR 2000.
BSR 2000 Command Reference Guide Release 1.0 show ip interface The show ip interface command displays the status, statistical information, and configuration for the network interfaces. The show ip interface command without any command arguments displays status, statistical information, and configuration for all interfaces.
Release 1.0 IP Commands exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip irdp The show ip irdp command displays ICMP Router Discovery Protocol information including interface holdtime values, configured preface values, and advertisement values for specified Ethernet or Gigabit Ethernet interfaces or all Ethernet or Gigabit Ethernet interfaces on the BSR.
Release 1.0 IP Commands count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip protocols The show ip protocols command is used for debugging routing activity and processes by displaying the status of routing protocol processes currently on the system.
Release 1.0 IP Commands show ip route The show ip route command displays the active entries in the routing table. Note: The information displayed reflects the routes that the routing table has exported in the routing protocol that were filtered by that protocol’s export routing policy statements. Group Access All Command Mode Privileged EXEC and Global Configuration Command Line Usage show ip route [ [
BSR 2000 Command Reference Guide 2-64 Release 1.0 rip Displays RIP routes. static Displays static routes. summary Displays a summary of routes in the BSR routing table.
Release 1.0 IP Commands show ip traffic The show ip traffic command displays IP, ICMP, UDP, TCP, ARP, OSPF, IGMP, PIM, and RADIUS protocol packet statistics, depending on what protocols are in use on the BSR.
BSR 2000 Command Reference Guide Release 1.0 show sntp The Simple Network Time Protocol (SNTP) provides system time with high accuracy.
Release 1.0 IP Commands show tcp brief The show tcp brief command displays a brief summary of TCP status and configuration. Group Access All Command Mode Privileged EXEC Command Line Usage show tcp brief 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show tcp statistics The show tcp statistics command displays the Transmission Control Protocol (TCP) statistics. The show tcp statistics command displays the following information: rcvd Statistics in this section refer to packets received by the router. total Packets received. no port Number of packets received with no port.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Command Mode Privileged EXEC Command Line Usage show tcp statistics 2-70 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands shutdown The shutdown command disables an interface. An interface is in a shutdown state when some configuration tasks must be performed on the interface. All interfaces on the BSR are shutdown by default. The no shutdown command is used to enable a disabled interface. Note: Use the show interfaces command to display which interfaces are enabled or disabled.
BSR 2000 Command Reference Guide Release 1.0 sntp authenticate The sntp authenticate command enables authentication for SNTP. The no sntp authenticate command disables authentication for SNTP. Group Access System Administrator Command Mode Global Configuration Command Line Usage sntp authenticate no sntp authenticate 2-72 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands sntp authentication-key The sntp authentication-key command enables authentication for SNTP. The no sntp authentication-key command disables authentication for SNTP. Use the sntp authentication-key command to authenticate SNTP sources for additional security. Group Access System Administrator Command Mode Global Configuration Command Line Usage sntp authentication-key <1-4294967295> [md5 ] no sntp authentication-key <1-4294967295> Command Syntax 1-4294967295 Key number.
BSR 2000 Command Reference Guide Release 1.0 sntp broadcastdelay The sntp broadcastdelay command establishes the length of a round trip between the system and a broadcast server. The no sntp broadcastdelay command removes the length of a round trip between the system and a broadcast server and returns it to the default. Use the sntp broadcastdelay command to set the exact time between the router as a broadcast client and the network.
Release 1.0 IP Commands sntp broadcast client The sntp broadcast client command configures a router to listen for SNTP broadcasts. The no sntp broadcast client command blocks the router from receiving SNTP broadcast traffic. Use the sntp broadcast client command to receive NTP traffic from a broadcast server. Group Access System Administrator Command Mode Global Configuration Command Line Usage sntp broadcast client no sntp broadcast client 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 sntp disable The sntp disable command disables SNTP on an interface. The no sntp disable command enables the interface to accept NTP traffic from other servers. Group Access System Administrator Command Mode Global Configuration Command Line Usage sntp disable no sntp disable Command Default Enabled 2-76 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands sntp server The sntp server command configures a router for SNTP to accept NTP traffic. The no sntp server command disables the router receiving NTP traffic. Note: When the server address is set to 224.0.1.1, the assigned multicast address for NTP, the BSR operates in unicast mode. It transmits a request to this multicast address and waits for replies. It then "binds" to the first server who replies. All subsequent transactions happen in a unicast mode.
BSR 2000 Command Reference Guide Release 1.0 Hostname Host server name. key 1-4294967295 Key number for authentication purpose. Command Default SNTP traffic not accepted from a time server 2-78 MGBI 526363-001-00 Rev.
Release 1.0 IP Commands sntp timer The sntp timer command specifies the time interval between queries to the SNTP server. The no sntp timer command remove the time interval. Group Access System Administrator Command Mode Global Configuration Command Line Usage sntp timer <1-86400> no sntp timer Command Syntax 1-86400 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 sntp trusted-key The sntp trusted-key command authorizes synchronization and authenticates system identity. The no ntp trusted-key command disables synchronization and removes system identity. Use the sntp trusted-key command to establish a key or keys following the sntp authentication-key command to synchronize the system. The sntp trusted-key command synchronizes with only those systems that are trusted delivering additional security.
Release 1.0 IP Commands traceroute The traceroute command is used to trace the route that packets take through the network from their source to their destination. The BSR sends out a sequence of User Datagram Protocol (UDP) datagrams to an invalid port address at the remote host to trace the route through the network, as follows: ■ ■ First, three UDP datagrams are sent, each with a TTL field value set to 1.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax A.B.C.D the source IP address. Hostname the Domain Name Server (DNS) hostname. Source A.B.C.
Release 1.0 IP Commands trap-enable-if The trap-enable-if command enables the ifLinkUpDownTrapEnable trap. The ifLinkUpDownTrapEnable trap indicates whether a link up or link down trap should be generated for an interface. The no trap-enable-if command disables the ifLinkUpDownTrapEnable trap. Group Access All Command Mode Interface Configuration Command Syntax trap-enable-if no trap-enable-if Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 trap-enable-rdn The trap-enable-rdn command enables the rdnCardIfLinkUpDownEnable trap. The rdnCardIfLinkUpDownEnable trap indicates whether a link up or link down trap should be generated for a BSR module. The no trap-enable-rdn command disables the rdnCardIfLinkUpDownEnable trap. Group Access All Command Mode Interface Configuration Command Syntax trap-enable-rdn no trap-enable-rdn Command Default Disabled 2-84 MGBI 526363-001-00 Rev.
3 SNMP Commands Introduction This chapter describes the Simple Network Management Protocol (SNMP) commands used to manage the BSR 2000. Since it was developed in 1988, SNMP has become the de facto standard for internetwork management. SNMP is an application layer protocol and is based on the manager/agent model. SNMP is referred to as simple because the agent requires minimal software.
BSR 2000 Command Reference Guide Release 1.0 SNMP Command Descriptions This section contains an alphabetized list and descriptions of the SNMP commands supported by the BSR. 3-2 MGBI 526363-001-00 Rev.
Release 1.0 SNMP Commands show snmp The show snmp command displays SNMP statistics, determine the running status, and display configuration information such as chassis ID, system description, and system location, chassis ID, and counter information for the SNMP process.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 SNMP Commands Command Syntax access Displays SNMPv3 access rights for SNMP groups and users with security models and levels. It also displays the associations between SNMP views and these security parameters. chassis-id Displays SNMP chassis-id information community Displays information about configured SNMP communities. contact Displays SNMP system contact information from the MIB object sysContact. context Displays SNMPv3 context information from the MIB object sysContext.
BSR 2000 Command Reference Guide 3-6 Release 1.0 traps Displays a list of SNMP traps. users Displays a list of configured SNMPv3 users stored in the SNMP group username table and their associated access privileges, such as engineID and security level. view Displays the SNMPv3 view-name and the object-identifier subtrees associated with it MGBI 526363-001-00 Rev.
Release 1.0 SNMP Commands snmp-server access The snmp-server access command defines access policy information. The no snmp-server access command clears the SNMP access policies.. Note: Community Name Access Method is used predominantly with SNMP v1 and v2c.
BSR 2000 Command Reference Guide 3-8 Release 1.
Release 1.0 SNMP Commands snmp-server chassis-id The snmp-server chassis-id command specifies a new chassis ID to uniquely identify the SNMP server’s chassis. The no snmp-server chassis-id command returns the chassis ID to the default value which is the serial number of the chassis.
BSR 2000 Command Reference Guide Release 1.0 snmp-server community The snmp-server community command enables SNMP and sets community strings and access privileges. The no snmp-server community command removes community strings and access privileges to a particular SNMP community.
Release 1.0 SNMP Commands snmp-server community-table The snmp-server community-table command configures the snmpCommunityTable which is part of the snmpCommunityMIB (RFC 2576). The snmpCommunityMIB defines objects to help support coexistence between SNMPv1, SNMPv2c, and SNMPv3. The snmpCommunityTable contains a database of community strings and provides mappings between community strings and the parameters required for View-based Access Control.
BSR 2000 Command Reference Guide 3-12 Release 1.
Release 1.0 SNMP Commands Command Default snmpCommunityStatus = active snmpCommunityStorageType = nonvolatile 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server contact The snmp-server contact command specifies the contact information in the sysContact MIB object Group Access System Administrator Command Mode Global Configuration Command Line Usage snmp-server contact Command Syntax string name of system contact person- provides text for the MIB object sysContact Command Default no contact set 3-14 MGBI 526363-001-00 Rev.
Release 1.0 SNMP Commands snmp-server context The snmp-server context defines or updates a context record. The no snmp-server context command clears a context record. Note: By defining a context record, an access policy can be specified that includes the context. The context record identifies object resources that are accessible.
BSR 2000 Command Reference Guide Release 1.0 snmp-server convert The snmp-server convert command converts a key or password to a localized authentication key.
Release 1.0 SNMP Commands snmp-server docs-trap-control The snmp-server docs-trap-control command enables various CMTS traps. The no snmp-server docs-trap-control disables the CMTS trap.
BSR 2000 Command Reference Guide 3-18 Release 1.
Release 1.0 SNMP Commands snmp-server enable informs The snmp-server enable informs command enables SNMP informs and allows this SNMP management station to send SNMP informs to hosts also configured to accept informs using this command. The snmp-server host command configures a host or hosts to accept SNMP informs. At least one SNMP-server host must be configured.
BSR 2000 Command Reference Guide Release 1.0 snmp-server enable traps The snmp-server enable traps command enables SNMP traps and allows the SNMP agent to send an unsolicited notification to one or more pre-configured management stations. The no snmp-server enable traps command disables all SNMP traps or a specific trap type.
Release 1.0 SNMP Commands registration enable CM (de)registration traps snmp enable SNMP state change traps snr enable signal-to-noise ratio measurement traps Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server engineID The snmp-server engineID command specifies an identification name (ID) for a local or remote SNMPv3 engine. The no snmp-server engineID command returns the local agent engineID to the default, or deletes a remote engineID from the agent. Note: A local SNMP Engine ID must be configured to use SNMPv3.The SNMP agent is configured with a default Engine ID equal to the MAC address of the chassis.
Release 1.0 SNMP Commands snmp-server group The snmp-server group command associates (or maps) SNMP groups to SNMP users. Use the no snmp-server group command to delete the group or a table to match SNMP users with SNMP groups. The snmp-server group command is used to create an SNMP group, associate it with an SNMP user, and define a security level (SNMPv1, v2c, v3) for use with the group.
BSR 2000 Command Reference Guide Release 1.0 snmp-server host The snmp-server host command configures the SNMP agent to send notifications to a remote host. You configure an SNMP inform or trap host with the snmp-server host command by specifying the receiver of specific inform or trap types. All informs or raps are sent if one is not specified. Each time the snmp-server host command is used, one host acting as a inform or trap recipient is configured.
Release 1.0 SNMP Commands no snmp-server host {} {informs { | version {1 | 2c | 3 {auth | noauth | priv}}} {traps { | version {1 | 2c | 3 {auth | noauth | priv}}} {version {1 | 2c | 3 {auth | noauth | priv} {}}} [bgp | docsdevcmts | entity | environ | flap | ospf | pim | snmp | snr | udp-port<0-65535>] ommand Syntax A.B.C.
BSR 2000 Command Reference Guide Release 1.0 snr enable signal-to-noise ratio meaurement traps udp-port 0-65535 the UDP port number for the host to use Command Default No hosts configured 3-26 MGBI 526363-001-00 Rev.
Release 1.0 SNMP Commands snmp-server location The snmp-server location command specifies the system location information in the sysLocation MIB object. Group Access System Administrator Command Mode Global Configuration Command Line Usage snmp-server location Command Syntax string 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server notify The snmp-server notify command specifies the target addresses for notifications by setting the snmpNotifyName object in the snmpNotifyTable and the snmpNotifyTag object in the snmpTargetAddrTable. The snmpNotifyTable contains entries which are used to select which entries in the snmpTargetAddrTable should be used for generating notifications and the type of notifications to be generated.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 snmp-server notify-filter The snmp-server notify-filter configures the snmpNotifyFilterTable.The snmpNotifyFilterTable is a table containing filter profiles. Filter profiles are used to determine whether a particular management target should receive particular notifications.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 snmp-server notify-filter-profile The snmp-server notify-filter-profile command configures the snmpNotifyFilterProfileTable. The snmpNotifyFilterProfileTable is used to associate a notification filter profile with a particular set of target parameters. An entry in this table indicates the name of the filter profile to be used when generating notifications using the corresponding entry in the snmpTargetParamsTable.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 snmp-server packetsize The snmp-server packetsize command sets the maximum SNMP packet size that the server sends or receives. The no snmp-server packetsize command sets SNMP packet size back to the default.
Release 1.0 SNMP Commands snmp-server port number The snmp-server port number sets the UDP port number the SNMP agent is to use. The no snmp-server port number sets the UDP port number the SNMP agent is to use back to the default. Group Access System Administrator Command Mode Global Configuration Command Line Usage snmp-server port number <0-65535> no snmp-server port number <0-65535> Command Syntax 0-65535 port number for the SNMP agent to listen Command Default 161 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server shutdown The snmp-server shutdown command shuts down the SNMP Agent, preventing it from further processing SNMP packets, while retaining all SNMP configuration data in the event the agent is restarted. The snmp-server shutdown delete command shuts down the SNMP Agent and deletes all SNMP configuration data (all SNMP configuration data is lost). Note: The snmp-server shutdown command is identical to the no snmp-server command.
Release 1.0 SNMP Commands snmp-server sysname The snmp-server sysname command specifies the system name information in the sysLocation MIB object. Note: The sysName MIB variable is the name of the node. The show snmp sysname command gets the sysName MIB variable. Group Access System Administrator Command Mode Global Configuration Command Line Usage snmp-server sysname Command Syntax string 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server target-addr The snmp-server target-addr command configures the SNMP target address entries in the snmpTargetAddressTable. The snmpTargetAddrTable contains information about transport domains and addresses to be used in the generation of SNMP operations. It also contains the snmpTargetAddrTagList object which provides a mechanism for grouping table entries.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 active sets the snmpTargetAddrRowStatus object to "active" not-in-service sets the snmpTargetAddrRowStatus object to "notInService" Command Default snmpTargetAddrMMS = 484 snmpTargetAddrRowStatus = active snmpTargetAddrStorageType = nonvolatile 3-40 MGBI 526363-001-00 Rev.
Release 1.0 SNMP Commands snmp-server target-params The snmp-server target-params configures the snmpTargetParamsTable. The snmpTargetParamsTable contains information about SNMP version and security information to be used when sending messages to particular transport domains and addresses. Entries in the snmpTargetParamsTable are created or deleted using the snmpTargetParamsRowStatus object.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 snmp-server trap rate-limit The snmp-server trap rate-limit command constricts the rate of SNMP messages and log messages sent to a remote host and used by the agent to send an unsolicited notification to one or more pre-configured management stations. The no snmp-server trap rate-limit clears the SNMP agent and increases the number of traps sent to a remote host.
Release 1.0 SNMP Commands snmp-server trap-source loopback The snmp-server trap-source loopback command allows an operator to control the source IP address of SNMP traps generated by the BSR by specifying a loopback interface as the source IP address for SNMP traps. The normal convention for generated SNMP traps is to set the source IP address equal to the IP address of the outgoing interface.
BSR 2000 Command Reference Guide Release 1.0 snmp-server user The snmp-server user command adds a new user to an SNMP group. The no snmp-server user command removes a user from an SNMP group.
Release 1.0 SNMP Commands eng HEX specifies engine-id with this user; local value of engine ID priv des56 provides DES-56 bit encryption with authentication based on the CBC-DES (DES-56) standard public octet-string sets the usmUserPublic MIB object 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snmp-server view The snmp-server view command defines an SNMPv2 MIB view. The no snmp-server view command removes the defined view. You can assign MIB views to SNMP Groups or community strings to limit the MIB objects that an SNMP manager can access. You can use a predefined view or create your own view. Other SNMP commands, such as snmp-server community, can use the view to create records associated with a view.
Release 1.
BSR 2000 Command Reference Guide 3-50 Release 1.0 transmission transmission MIB group udp UDP MIB group included specifies MIB group is included from view excluded specifies MIB group is excluded from view MGBI 526363-001-00 Rev.
4 Debug Commands Introduction This chapter describes the debug commands supported by the BSR 2000. Debug commands help to isolate the source of a system failure. The output provides diagnostic information, protocol status, and network activity which can be used to diagnose and resolve networking problems. Debug Command Descriptions This section contains an alphabetized list and descriptions of the debug commands supported by the BSR. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug arp The debug arp command displays Address Resolution Protocol (ARP) information exchanges between the BSR and other devices on the network. The no debug arp command turns off ARP debugging. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug arp no debug arp 4-2 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable cra The debug cable cra command turns on cra debugging which displays internal CMTS resource agent activity. The no debug cable cra command turns off cra debugging. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable cra no debug cable cra 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug cable err The debug cable err command displays miscellaneous error conditions. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable err no debug cable err 4-4 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable keyman The debug cable keyman command activates debugging of TEK and KEK baseline privacy key activity. The no debug cable keyman turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable keyman no debug cable keyman 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug cable mac The debug cable mac command displays dynamic service messages and/or MAC layer management information MAC-layer information. The no debug cable mac command turns off MAC-layer debugging. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable mac {dynsrv | information} no debug cable mac {dynsrv | information} 4-6 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable map The debug cable map command displays map debugging messages. The no debug cable map command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable map no debug cable map 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug cable modem-select The debug cable modem-select command lets you select a specific cable modem for debug tracing. The no debug cable modem-select command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable modem-select no debug cable modem-select Command Syntax mac 4-8 MAC address of a specific cable modem MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable privacy The debug cable privacy command activates debugging of baseline privacy. The no debug cable privacy command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable privacy no debug cable privacy 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug cable qos The debug cable qos command activates debugging of Quality of Service (QoS). The no debug cable qos command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable qos no debug cable qos 4-10 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable range The debug cable range command displays ranging messages exchanged between cable modems and the CMTS. The no debug cable range command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable range no debug cable range 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug cable reg The debug cable reg command displays registration messages exchanged between cable modems and the CMTS. The no debug cable reg command turns off this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable reg no debug cable reg 4-12 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug cable ucc The debug cable ucc command displays upstream channel change (UCC) messages generated when cable modems request or are assigned a new channel. The no debug cable ucc command turns of this debugging operation. Group Access MSO Command Mode Privileged EXEC Command Line Usage debug cable ucc no debug cable ucc 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ip access-list The debug ip access-list command enables IP access-list debugging. The no debug ip access-list command turns IP access-list debugging off. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip access-list [{in | out }] no debug ip access-list [{in | out }] Command Syntax in debug inbound packets out debug outbound packets Command Default Disabled 4-14 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip bgp The debug ip bgp command displays Border Gateway Protocol (BGP) transactions. The no debug ip bgp command turns off this debugging operation.
BSR 2000 Command Reference Guide 4-16 Release 1.
Release 1.0 Debug Commands debug ip icmp The debug ip icmp command displays Internet Control Message Protocol (ICMP) information exchanges between the BSR and other devices on the network. The no debug ip icmp turns off ICMP debugging. Use the debug ip icmp command to determine whether the BSR is sending or receiving ICMP messages. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip icmp no debug ip icmp Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ip igmp The debug ip igmp command displays all Internet Group Management Protocol (IGMP) packets, and all IGMP host-related actions. The no debug ip igmp command turns off the IGMP debugging. Use the debug ip igmp command to target IGMP protocol messages and mtrace messages. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip igmp no debug ip igmp Command Default Disabled 4-18 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip mfm The debug ip mfm command displays Multicast Forwarding Manager (MFM) control packet activity. The no debug ip mfm command turns off MFM debugging. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip mfm {all | general} no debug ip mfm {all | general} Command Syntax all all MFM processing information general general, non-specific MFM application information Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ip mrtm The debug ip mrtm command displays changes made to the IP multicast routing table made by the Multicast Routing Table Manager. The no debug ip mrtm command turns off MRTM debugging.
Release 1.0 Debug Commands debug ip ospf The debug ip ospf command displays Open Shortest Path First (OSPF)-related activity. The no debug ip ospf command turns off OSPF-related debugging. Use the debug ip ospf command to turn on debugging for IP OSPF.
BSR 2000 Command Reference Guide Release 1.0 Command Default Disabled 4-22 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip packet The debug ip packet command displays general IP debugging information including packets received, generated, and forwarded. The no debug ip packet command turns IP debugging operations. Note: The debug ip packet command uses considerable bandwidth to output debugging information. This may interrupt router activities.
BSR 2000 Command Reference Guide Release 1.0 debug ip pim The debug ip pim command enables PIM debugging. The no debug ip pim command turns PIM debugging off.
Release 1.0 Debug Commands Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ip policy The debug ip policy command displays IP policy routing packet activity. The debug ip policy command displays information about whether a packet matches the routing policy criteria and the resulting routing information for the packet.The no debug ip policy command turns off IP policy debugging. Note: The debug ip policy command uses considerable bandwidth to output debugging information. This may interrupt router activities.
Release 1.0 Debug Commands debug ip redistribute to The debug ip redistribute to command displays route redistribution information from one routing domain to another routing domain. The no debug ip redistribute command turns off IP redistribute debugging.
BSR 2000 Command Reference Guide Release 1.0 rip routes redistributed from RIP static routes redistributed static Command Default Disabled 4-28 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip rip The debug ip rip command displays Routing Information Protocol (RIP) send and receive information. The no debug ip rip command turns off RIP debugging.
BSR 2000 Command Reference Guide Release 1.0 debug ip rip database The debug ip rip database command displays information on RIP route entry events; additions, deletions, and changes. The no debug ip rip database command turns off RIP database debugging. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip rip database no debug ip rip database 4-30 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip rip events The debug ip rip events command displays information on RIP-related events. The no debug ip rip events command turns off RIP-related event debugging. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip rip events no debug ip rip events Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ip rip trigger The debug ip rip trigger command displays RIP routing events that occur as a result of RIP trigger extensions. The no debug ip rip trigger command turns off RIP triggered events debugging. Group Access ISP Command Mode All modes except User EXEC Command Line Usage debug ip rip trigger no debug ip rip trigger Command Default Disabled 4-32 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug ip tcp transactions The debug ip tcp transactions command displays information on significant TCP activity such as state changes, retransmissions, and duplicate packets. The no debug tcp transactions command turns off TCP debugging. Note: The debug ip tcp transactions command reports output for packets the BSR 2000 transmits and receives, but does not display output for packets it forwards.
BSR 2000 Command Reference Guide Release 1.0 debug ip udp The debug ip udp command displays UDP-based transactions.The debug output shows whether packets are being received from the host. The no debug ip udp command turns off UDP debugging.
Release 1.0 Debug Commands debug ipsec ike The debug ipsec ike command turns on IKE debugging and prints IKE debug messages to the console. The debug ipsec ike command, without additional arguments, turns on all IKE debugging. The no debug ipsec ike command turns IKE debugging off. IKE debugging must be re-enabled after a power-cycle or reload.
BSR 2000 Command Reference Guide Release 1.0 debug ipsec ipsec The debug ipsec ipsec command turns on IPSec debugging and prints IPSec debug messages to the console. The debug ipsec ipsec command, without additional arguments, turns on all IPSec debugging.The no debug ipsec ipsec command turns IPSec debugging off. IPSec debugging must be re-enabled after a power-cycle or reload.
Release 1.0 Debug Commands debug ipsec sadb The debug ipsec sadb command turns on Security Association Database (SADB) debugging and prints SADB debug messages to the console. The no debug ipsec sadb command turns SADB debugging off. SADB debugging must be re-enabled after a power-cycle or reload. Group Access All Command Mode All modes except User EXEC Command Line Usage debug ipsec sadb no debug ipsec sadb Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ipsec spd The debug ipsec spd command urns on SPD debugging and prints SPD debug messages to the console. The no debug ipsec spd command turns SPD debugging off. SPD debugging must be re-enabled after a power-cycle or reload. Group Access All Command Mode All modes except User EXEC Command Line Usage debug ipsec spd no debug ipsec spd Command Default Disabled 4-38 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug packet-cable The debug packet-cable command enables Packet Cable debugging. The no debug packet-cable command disables debugging output.
BSR 2000 Command Reference Guide Release 1.0 debug radius The debug radius command displays RADIUS client authentication transactions. The no debug radius command turns off RADIUS debugging. Group Access All Command Mode All modes except User EXEC Command Line Usage debug radius no debug radius 4-40 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug snmp The debug snmp command display detailed information about every SNMP packet transmitted or received by the BSR 2000. The no debug snmp command turns off SNMP debugging. Group Access All Command Mode All modes Command Line Usage debug snmp {headers | packets} no debug snmp {headers | packets} Command Syntax headers display SNMP packet headers packets display SNMP packets Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug sntp The debug sntp command displays information on Simple Network Time Protocol (SNTP) activity. The no debug sntp command turns off SNTP debugging. Group Access System Administrator Command Mode All modes except User EXEC Command Line Usage debug sntp no debug sntp 4-42 MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug specmgr The debug specmgr command enables the display of spectrum management debugging messages. The command output displays a time stamp, the error rate, the number of word errors, total word count, and the upstream noise power level in one-tenth of a dBmV. The no debug specmgr stops displaying spectrum management debugging messages.
BSR 2000 Command Reference Guide Release 1.0 debug ssh The debug ssh command enables debugging for SSH. The no debug ssh command turns SSH debugging off. Group Access All Command Mode All modes except User EXEC Command Line Usage debug ssh [verbose {1-8}] no debug ssh [verbose {1-8}] Command Syntax 4-44 verbose display detailed SSH debug information 1-8 verbose debug level number MGBI 526363-001-00 Rev.
Release 1.0 Debug Commands debug tacacs The debug tacacs command displays debug information associated with TACACS+ Client operations. Group Access All Command Mode Privileged EXEC Command Line Usage debug tacacs 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug tacacs events The debug tacacs events command displays debug information related to TACACS+ server events generated as a result of interaction with a client. This command can produce substantial amount of output on the console. The debug tacacs events command is generally used as a tool to collect data to analyze a problem reported by users.
Release 1.0 Debug Commands show debugging The show debugging command displays enabled debugging operations and other types of debugging functions on the system.
BSR 2000 Command Reference Guide Release 1.0 undebug all The undebug all command disables all debugging functions on the system. Group Access System Administrator Command Mode All modes except User EXEC Command Line Usage undebug all 4-48 MGBI 526363-001-00 Rev.
5 Access List Commands Introduction This chapter describes the access list commands used with the BSR 2000™. Access lists are used on the BSR to control entry or exit access to or from the BSR. Access lists are also used within a route-map statement that is part of the routing configuration. Access lists can be configured for all routed network protocols to filter packets as the packets pass through the BSR.
BSR 2000 Command Reference Guide Release 1.0 access-class in The access-class in command filters incoming connections based on an IP access list. Group Access System Administrator Command Mode Global Configuration Command Line Usage access-class {<1-99> | <1300-1999>} in Command Syntax 5-2 1-99 the IP access-list number 1300-1999 the IP access-list number (expanded range) MGBI 526363-001-00 Rev.
Release 1.0 Access List Commands access-list (standard) The standard access-list command defines a standard access list to configure and control the flow of routing information and traffic by matching a packet with a permit or deny result. The no access-list command deletes the access-list. Use the access-list command to restrict routing update information; control the transmission of packets on an interface, or control virtual terminal line access.
BSR 2000 Command Reference Guide Release 1.0 access-list (extended) The extended access-list command defines an extended access list to configure and control the flow of routing information and traffic by matching a packet with a permit or deny result. The no access-list command deletes the access-list. Use the access-list command to restrict routing update information; control the transmission of packets on an interface, or control virtual terminal line access.
Release 1.0 Access List Commands To configure an extended access list for IGMP, use the following command: access-list <100-199> <2000-2699> {deny | permit} igmp { | any | host } ( | any | host } [<0-255> | diff-serv | host-query | host-report | pim ] To configure an extended access list for TCP, use the following command: access-list <100-199> <2000-2699> {deny | permit} tcp { | any | host } (
BSR 2000 Command Reference Guide 5-6 Release 1.0 0-255 ahp esp gre icmp igmp ip ipinip ospf pcp pim tcp udp name or number of an IP protocol A.B.C.D source address A.B.C.D source wildcard bits any any source host host A.B.C.D a single source host A.B.C.D destination address A.B.C.D destination wildcard bits any any destination host host A.B.C.D a single destination host diff-serv <0-63> Value of IP Diff-Serv MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 timestamp-reply timestamp-request ttl-exceeded unreachable 5-8 0-255 diff-serv host-query host-report pim filter IGMP packets by message type (0-255) or message type name diff-serv eq only match packets on a given TCP or UDP port number or name MGBI 526363-001-00 Rev.
Release 1.0 Access List Commands 0-65535 bgp chargen cmd daytime discard domain echo exec finger ftp ftp-data gopher gt hostname ident irc klogin kshell login lpd lt neq nntp pim-auto-rp pop2 pop3 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 range smtp sunrpc talk telnet time uucp whois www 5-10 MGBI 526363-001-00 Rev.
Release 1.0 Access List Commands 0-65535 biff bootpc bootps diff-serv discard domain echo gt lt mobile-ip neq netbios-dgm netbios-ns netbios-ss ntp pim-auto-rp range rip snmp snmptrap sunrpc syslog talk tftp time who xdmcp 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip access-group Use the ip access-group command to assign an access list to an interface and determine if the interface accepts inbound or outbound packets, or both from this access list. The no ip access-group command removes the access list or disables inbound or outbound packets.
Release 1.0 Access List Commands ip access-list The ip access-list command adds a standard or extended access-list entry. The no ip access-list command removes the entry. Group Access ISP Command Mode Global Configuration Command Line Usage ip access-list {standard <1-99> | extended <100-199>} no ip access-list {standard <1-99> | extended <100-199>} Command Syntax standard 1-99 standard access list number extended 100-199 extended access list number 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show access-lists The show access-lists command displays an access list, or all access lists, without displaying the entire configuration file.
6 Routing Policy Commands Introduction This chapter contains the Routing Policy and Policy-Based Routing commands used with the BSR 2000™. Routing Policy allows the control of information that is imported from or exported into different routing domains or Autonomous Systems (AS). BSR Routing Policy allows the filtering and altering of routing information so that some of them can be advertised to other routers. The BSR Routing Policy is quite versatile and flexible.
BSR 2000 Command Reference Guide Release 1.0 default-information originate The default-information originate command injects the default network in a routing domain such as Border Gateway Protocol (BGP).The no default-information originate command disables the default network redistribution in the routing domain. The network 0.0.0.0 command in Router Configuration mode performs the same function as the default-information originate command.
Release 1.0 Routing Policy Commands Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 default-metric The default-metric command sets the default metric value for redistribution of routes from one domain into another. The no default-metric command removes the set default value for metric. Use the default-metric command with the redistribute command to enforce the same metric value for all redistributed routes.
Release 1.0 Routing Policy Commands ip local policy route-map The ip local policy route-map command enables local policy routing for a specified route map. The no ip local policy route-map command disables local policy routing for a specified route map. Group Access ISP Command Mode Global Configuration Command Line Usage ip local policy route-map no ip local policy route-map Command Syntax WORD 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip policy route-map The ip policy route-map command identifies the route-map used on an interface to perform policy-based routing. The no ip policy route-map command removes the route-map on an interface, and disables policy-based routing on that interface. Use the ip policy route-map command for paths other than the shortest path.
Release 1.0 Routing Policy Commands match as-path The match as-path command matches a BGP autonomous system path access list to a match entry or appends new list numbers to the existing match entry. The no match as-path command removes the list numbers from the match entry used in the command. Use the match as-path command to match a BGP autonomous system path to advertise on the route-map. Values can be set using the match as-path command.
BSR 2000 Command Reference Guide Release 1.0 match community The match community command creates a BGP autonomous system community access list match entry or appends new list numbers to the existing match entry. The no match community command removes the match entry completely. The no match community command removes the list numbers or the exact-match attribute from the match entry. Use the match community-list command to ensure that the route is advertised for outbound and inbound route-maps.
Release 1.0 Routing Policy Commands match ip address The match ip address command matches the destination and source IP address or other fields of the IP header on packets with a standard or extended access list allocated. The no match ip address command disables policy routing on packets. This command can also be used for filtering routes based on the destination network of the route.
BSR 2000 Command Reference Guide Release 1.0 match ip next-hop The match ip next-hop command establishes the condition for the next hop IP address of a route to match against the specified access lists. The no match ip next-hop command removes the access-list from the match condition. Use the match ip next-hop command to match any routes that have a next-hop router address permitted one of the specified access lists.
Release 1.0 Routing Policy Commands match ip route-source The match ip route-source command specifies match conditions for the source IP address of a route to match against the specified address list(s). The no match ip route-source command removes access lists from such a match statement. The match ip route-source command is used to match routes where source IP addresses are permitted by specified access lists.
BSR 2000 Command Reference Guide Release 1.0 match metric The match metric command matches routes imported or otherwise with specified metric value. The no match metric command disables matching imported routes with specified metric values. Use the match metric command to match a route for the specified metric value(s).
Release 1.0 Routing Policy Commands match route-type external The match route-type external command is used to match the type of OSPF routes. The no match route-type external clears the match condition.
BSR 2000 Command Reference Guide Release 1.0 match route-type internal The match route-type internal command matches and redistributes OSPF routes of an internal type. The no match route-type internal command clears the condition. Group Access ISP Command Mode Route-map Configuration Command Line Usage match route-type internal [level-1 | level-2] no match route-type internal [level-1 | level-2] Command Syntax 6-14 level-1 IS-IS level-1 route level-2 IS-IS level-2 route MGBI 526363-001-00 Rev.
Release 1.0 Routing Policy Commands match tag The match tag command redistributes routes in the routing table that match a specified tag value. Use the no match tag command to disable redistributing routes in the routing table that match a specified tag. Group Access ISP Command Mode Route Map Configuration Command Line Usage match tag [<0-4294967295>] no match tag Command Syntax 0-4294967295 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 route-map The route-map command defines the conditions for redistributing routes from one protocol to another, or to configure routing policies. The no route-map command removes some or all of the instances of the route map. Use the route-map command and the match and set commands, to define the conditions for redistributing routes from one routing protocol into another, or for accepting routes from a neighboring router.
Release 1.0 Routing Policy Commands Command Syntax WORD tag name, more than one instance of the route-map can share name permit distributes route as controlled by set actions when permit is specified and the match criteria are met, the route is specified by the specific actions deny distributes route as controlled by set actions, if criteria not met, route not distributed 0-65535 position a new instance will have in the list of route-map instances already established with the same map name.
BSR 2000 Command Reference Guide Release 1.0 set as-path prepend The set as-path prepend command modifies AS system path attributes for the matched BGP routes. The no set as-path prepend command ends modification of a system path for BGP routes. Use the set as-path prepend command to guide the path information to control the BGP decision process.
Release 1.0 Routing Policy Commands set automatic-tag The set automatic-tag command enables the automatic computing of tag values. The no set automatic-tag command disables the automatic computing of tag values. Group Access ISP Command Mode Route Map Configuration Command Line Usage set automatic-tag no set automatic-tag 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set comm-list The set comm-list command deletes communities from the community attribute of an inbound or outbound update. The no set comm-list command deletes the entry. Use the set comm-list command to delete communities from the community attribute of inbound or outbound updates using a route map to filter and determine the communities to be deleted.
Release 1.0 Routing Policy Commands 100-199 extended community list number delete delete inbound or outbound communities from the community attribute 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set community The set community command add or replace communities from the community attribute of an inbound or outbound update. Use the no set community command removes the specified communities from the set. Use the route-map command, and the match and set commands to configure the rules for redistributing routes from one routing protocol to another. Each route-map command has a list of match and set commands associated with it.
Release 1.0 Routing Policy Commands Command Syntax 1-4294967295 community number additive add to the existing community local-AS do not advertise this route to peers outside of the local autonomous system no-advertise do not advertise this route to any peer internal or external no-export routes with this community are sent to peers in other sub-autonomous systems within a confederation none no community attribute 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set default interface null0 The set default interface null0 command adds “null0” as the last entry in the interface list to force packets to be dropped and not routed with the default destination-based routing process. The no set default interface null0 command disables this function.
Release 1.0 Routing Policy Commands set interface null0 The set interface null0 command adds “null0” as the last entry in the interface list to force packets to be dropped and not routed with the default destination-based routing process. The no set interface null0 command disables this function. Group Access ISP Command Mode Route Map Configuration Command Line Usage set interface null0 no set interface null0 Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set ip default next-hop The set ip default next-hop command specifies a default next hop IP address that indicates where the BSR sends packets that pass a match clause in a route map for policy routing but have no route to the destination. The no set ip default next-hop removes the default next hop IP address.
Release 1.0 Routing Policy Commands set ip diff-serv The set ip diff-serv command assigns a differentiated service value which is placed in the IP packet header that determines which packets are given transmission priority. When these packets are received by another router, they are transmitted based on the precedence value. A higher precedence value indicates a higher priority. The no set ip diff-serv command disables assigning a differentiated service value.
BSR 2000 Command Reference Guide Release 1.0 Command Default 0 6-28 MGBI 526363-001-00 Rev.
Release 1.0 Routing Policy Commands set ip next-hop The set ip next-hop command establishes a next-hop value for the AS path. The no ip next-hop command deletes the entry. Use the ip policy route-map interface configuration command, the route-map global configuration command, and the match and set route-map configuration commands, to define the conditions for policy routing packets. The ip policy route-map command identifies a route map by name.
BSR 2000 Command Reference Guide Release 1.0 set ip qos queue The set ip qos queue command specifies Quality Of Service (QoS) queue number. Group Access All Command Mode Route Map Configuration Command Line Usage set ip qos queue <0-3> Command Syntax 0-3 6-30 the QoS queue number MGBI 526363-001-00 Rev.
Release 1.0 Routing Policy Commands set local-preference The set-local preference command establishes a preference value for the AS system path. Use the set local-preference command to send the local-preference to all routers in the local autonomous system. Use the no set-local preference form of this command to delete the entry. Note: In the no set-local preference command, the optional <0-4294967295> argument has no effect.
BSR 2000 Command Reference Guide Release 1.0 set metric The set metric command sets the metric value for a routing protocol. The no set metric command changes the metric value for a routing protocol to the default value.
Release 1.0 Routing Policy Commands set metric-type The set metric-type command sets the metric type for the destination routing protocol. The no set metric-type command disables the metric type set for the destination routing protocol. Use the route-map command to set the type of metric for the route imported by OSPF into its domain.
BSR 2000 Command Reference Guide Release 1.0 set origin The set origin command configures the conditions for redistributing routes from any protocol to any protocol. The no set origin command deletes the BGP origin code. When the set origin command configures redistributing routes from any protocol to any protocol, any match clause is necessary which includes pointing to a “permit everything” to set tags.
Release 1.0 Routing Policy Commands set tag The set tag command sets the value of the destination routing protocol. The no set tag command removes the value. The route-map global configuration command and the match and set route-map configuration commands are used together to define the conditions for redistributing routes from one routing protocol into another. Each route-map command has a list of match and set commands associated with it.
BSR 2000 Command Reference Guide Release 1.0 set weight The set-weight command to set the route weight on the network. The first autonomous system match determines the weight to be set. Use the set weight command to set the route weight on the network. The first AS match determines the weight to be set. The route with the highest weight is chosen as the choice route when multiple routes are available on the network.
Release 1.0 Routing Policy Commands show ip redistribute The show redistribute command displays the routing protocols that are being redistributed to other routing domains.
BSR 2000 Command Reference Guide 6-38 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 Routing Policy Commands show ip traffic The show ip traffic command displays the number of routing policy forwards and routing policy drops.
BSR 2000 Command Reference Guide Release 1.0 show route-map The show route-map command displays route maps.
7 RIP Commands Introduction This chapter contains the Routing Information Protocol (RIP) commands used with the BSR 2000™. RIP exchanges routing information to resolve routing errors. RIP coordinates routers on the network to broadcast their routing database periodically and determine the route with the least number of hops relative to the active routing table. Each hop determination message lists each destination with a distance in number of hops to the destination.
BSR 2000 Command Reference Guide Release 1.0 auto-summary The auto-summary command restores automatic summarization of subnet routes into network-level routes. The no auto summary command disables automatic summarization. Note: RIP Version 1 always uses automatic summarization. RIP Version 2 when routing between disconnected subnets, requires automatic summarization to be off which is the default state.
Release 1.0 RIP Commands clear ip rip statistics The clear ip rip statistics command clears all routes from the RIP routing table. This is the same route information displayed with the show ip rip database command. Group Access ISP Command Mode All modes except User EXEC Command Line Usage clear ip rip statistics 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 default-information originate The default-information originate command generates a default route into the RIP database. The no default-information originate command disables default route generation. Group Access ISP Command Mode Router Configuration Command Line Usage default-information originate no default-information originate Command Default Disabled 7-4 MGBI 526363-001-00 Rev.
Release 1.0 RIP Commands default-metric The default-metric command specifies a new RIP default metric value. The no metric command returns the metric value to the default. Use the default-metric command to set the current protocol to the same metric value for all distributed routes. The default-metric command is used with the redistribute command to obtain the same metric value for all distributed protocol-specific routes. Note: This command assures that metrics are compatible during route redistribution.
BSR 2000 Command Reference Guide Release 1.0 distance The distance command sets the administrative distances for routes. The no distance command disables the administrative distance for routes. Group Access ISP Command Mode Router Configuration Command Line Usage distance <1-255> no distance <1-255> Command Syntax 1-255 administrative distance for setting routes Command Default 120 7-6 MGBI 526363-001-00 Rev.
Release 1.0 RIP Commands distribute-list in The distribute-list in command filters networks received in routing updates. The no distribute-list in command changes or cancels the filters received in updates.
BSR 2000 Command Reference Guide Release 1.0 distribute-list out The distribute-list out command prevents networks from being advertised in updates. The no distribute-list out command enables update advertisements. Use the distribute-list out command to apply the access list to outgoing route updates.
Release 1.0 RIP Commands graceful-restart-period The graceful-restart-period command enables RIP graceful restart. Graceful restart allows a RIP router to stay on the forwarding path even as its RIP software is being restarted. As the graceful restart procedure executes, the RIP routing table is updated with recalculated route entries that replace older entries in the routng table which are marked with a “replicated” flag.
BSR 2000 Command Reference Guide Release 1.0 ip rip authentication key The ip rip authentication key command enables RIP authentication on an interface by specifying a password or group of passwords that can be used on that interface. The no rip authentication key command deletes the associated password(s). Note: Only RIP version 2 supports authentication.
Release 1.0 RIP Commands ip rip host-routes The ip rip host-routes command enables sending or receiving host routes with RIP version 1 for an interface. The no ip rip host-routes command disables sending or receiving host routes with RIP version 1 for an interface. Group Access ISP Command Mode Interface Configuration Command Line Usage ip rip host-routes no ip rip host-routes Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip rip message-digest-key The ip rip message-digest-key command enables RIP MD5 authentication. The no ip rip message-digest-key command disables RIP MD5 authentication. Use the ip rip message-digest-key command to generate authentication information when sending packets and to authenticate incoming packets. Neighbor routers must have the same key identifier.
Release 1.0 RIP Commands ip rip receive version The ip rip receive version command configures an interface to only receive packets from a specific version of the RIP protocol. Use the ip rip receive version command to configure the interface to receive one or both RIP versions. The no ip rip receive version command resets the RIP protocol version to RIP version 1 and 2.
BSR 2000 Command Reference Guide Release 1.0 ip rip send version The ip rip receive version command configures an interface to only transmit packets from a specific version of the RIP protocol. Use the ip rip receive version command to configure the interface to transmit one or both RIP versions. The no ip rip receive version command resets the RIP protocol version to RIP version 2.
Release 1.0 RIP Commands ip split-horizon The ip split-horizon command blocks route information from being advertised by a router out any interface from which that information originated. Enabling split-horizon optimizes communications among multiple routers, particularly when links are broken. The no ip split-horizon disables split-horizon. Group Access ISP Command Mode Interface Configuration Command Line Usage ip split-horizon no ip split-horizon Command Default Enabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 maximum-paths The maximum-paths command specifies the maximum number of parallel routes an IP routing protocol can support. The no maximum-paths command changes or cancels the number of maximum paths. Group Access RESTRICTED Command Mode Router Configuration Command Line Usage maximum-paths <1-2> no maximum-paths Command Syntax 1-2 7-16 the maximum number of parallel routes MGBI 526363-001-00 Rev.
Release 1.0 RIP Commands network The RIP version of the network command enables networks for the routing process. The no network command disables networks for the RIP routing process. Note: If a network with RIP is not specified, the system does not advertise the network in any RIP routes. Group Access ISP Command Mode Router Configuration Command Line Usage network [] no network ] Command Syntax A.B.C.D IP address of directly connected networks A.B.C.
BSR 2000 Command Reference Guide Release 1.0 offset-list The offset-list command adds an offset to incoming and outgoing metrics to routes learned via RIP. The offset value is added to the routing metric. An offset-list with an interface slot/port is considered extended and takes precedence over an offset-list that is not extended. The no offset-list command removes the offset for incoming and outgoing metrics to routes learned via RIP.
Release 1.0 RIP Commands ethernet X/Y X is 0. Y is the Ethernet interface port number to which the offset-list is applied. gigaether X/Y X is 0. Y is the Gigabit Ethernet interface port number to which the offset-list is applied. Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 output-delay The output-delay command changes the inter-packet delay for RIP updates to ensure that transmitted information is received by lower-speed routers. The no output delay command removes the inter-packet delay for RIP updates. Note: This command helps prevent the loss of routing table information.
Release 1.0 RIP Commands passive-interface The passive-interface command disables an interface from sending route updates by prohibiting packets from being transmitted from a specified port. When disabled, the subnet continues advertising to other interfaces. The no passive-interface command enables the interface to send route updates.
BSR 2000 Command Reference Guide Release 1.0 redistribute The redistribute command redistributes routes from one protocol domain to another routing domain. The no redistribute command disables route distribution from one protocol domain to another routing domain.
Release 1.0 RIP Commands external 2 routes that are external to an autonomous system, but are imported into OSPF as Type 2 external route static IP or RIP static routes metric metric used for the redistributed route. 1-16 the RIP default metric route-map route-map used to conditionally control the route redistribution WORD the name of the route-map Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 router rip The router rip command enables the routing process for RIP. The no router rip command disable the RIP routing process. Group Access ISP Command Mode Global Configuration Command Line Usage router rip no router rip 7-24 MGBI 526363-001-00 Rev.
Release 1.0 RIP Commands show ip rip database The show ip rip database command displays RIP database routing table information.The following is an example of typical screen output from the show ip rip database command: 172.19.13.0 10.10.0.0 172.22.251.0 172.22.244.0 10.10.10.0 12.12.12.0 50.0.0.0 21.21.21.0 58.0.0.0 80.0.0.0 4.4.4.0 80.80.80.0 172.22.0.0 10.0.0.0 4.0.0.0 58.58.58.0 12.0.0.0 172.19.0.0 172.168.0.0 21.0.0.0 50.50.50.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.252.0 255.255.255.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 RIP Commands source-port 520 The source-port 520 command enables UDP port 520 to be used by the RIP routing process. The no source-port 520 command disables UDP port 520. Group Access ISP Command Mode Router Configuration Command Line Usage source port 520 no source port 520 Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 timers basic The timers basic command configures RIP network timers. The no timers basic command resets the network timer default.
Release 1.0 RIP Commands invalid interval in seconds, routing updates 1-4294967295 Interval of time (in seconds) after which a route is declared invalid; it should be at least three times the value of the update argument. A route becomes invalid when there is an absence of updates that refresh the route. The route then enters into a holddown state. The route is marked inaccessible and advertised as unreachable. However, the route is still used for forwarding packets.
BSR 2000 Command Reference Guide Release 1.0 version The version command specifies the routing RIP version. The no version command disables the routing RIP version and resets the default. Use the ip rip receive version and the ip rip send version commands to specify versions per interface. Note: The basic timers for RIP are adjustable, but must be the same for all routers and servers on the network to execute a distributed, asynchronous routing algorithm.
8 OSPF Commands Introduction This chapter describes the Open Shortest Path First (OSPF) commands used with the BSR 2000™. OSPF is a link-state routing protocol that runs internally to a single Autonomous System, such as an enterprise network. At the core of the OSPF protocol is a distributed, replicated link-state database. OSPF specifies a Link-state Advertisements (LSAs) that allow OSPF routers to update each other about the LAN and WAN links to which they connected.
BSR 2000 Command Reference Guide Release 1.0 area authentication Use the area authentication command to enable authentication for an OSPF area to Type 1, Type 2, simple password, as specified in RFC 1247, while specification of Type 0 is assumed. Authentication type must match all routers and access servers in a particular area. The no authentication command disables authentication for the specified OSPF area.
Release 1.0 OSPF Commands area default-cost Use the area default-cost command to specify a cost metric for the default summary route sent into the stub area by an area border router (ABR) only. The no area default-cost command removes the specified cost for the default summary route sent into a stub area. Note: The area stub command is used in conjunction with the area default-cost command to define a specified area as a stub area for all routers and access servers attached to the area.
BSR 2000 Command Reference Guide Release 1.0 area nssa Use the area nssa command to configure an area as a Not So Stubby Area (NSSA). The no nssa command removes the NSSA configuration of an area. Group Access ISP Command Mode Router Configuration Command Line Usage area {<0-4294967295> | } nssa [default-information-originate] [no-redistribution] [no-summary] no area {<0-4294967295> | } nssa [default-information-originate] [no-redistribution] [no-summary] no area {<0-4294967295> |
Release 1.0 OSPF Commands area range Use the area range command to consolidate routes for an Area Border Router (ABR) only by advertising a single summary route that is advertised for each address range that is external to the area. The no area range command removes summarized routes for the ABR. Group Access ISP Command Mode Router Configuration Command Line Usage area {<0-4294967295> | } range [advertise | not-advertise | ] no area {<0-4294967295> |
BSR 2000 Command Reference Guide Release 1.0 area stub Use the area stub command to configure an OSPF area as a stub area. A stub area allows a default route, intra-area routes, and inter-area routes, but disallows autonomous system (AS) external routes, virtual links, and Autonomous System Boundary Router (ASBR) routes. Note: If there is more than one router within a stub area, ensure that the area that you are creating as a stub area is defined as a stub area on each of these routers.
Release 1.0 OSPF Commands area virtual-link Use the area virtual link command to create a virtual link that connects an OSPF area to the backbone area (area 0.0.0.0) without being physically connected to the OSPF backbone area. Use the no area virtual-link command to delete the defined OSPF virtual link. Group Access ISP Command Mode Router Configuration Command Line Usage area {<0-4294967295> | } virtual-link
BSR 2000 Command Reference Guide Release 1.0 hello-interval 1-65535 Time in seconds between hello packets on an interface, value must be the same for all routers and access servers attached to a common network. message-migest-key 1-255 OSPF MD5 authentication key. md5 WORD Encrypted md5 password (1-16 characters) retransmit-interval 1-65535 Expected round-trip delay between two routers on the attached network, value must be more than expected delay.
Release 1.0 OSPF Commands auto-cost reference-bandwidth The BSR OSPF routing process calculates the OSPF cost metric for an interface according to the bandwidth of this interface. The cost of an interface depends on the type of interface. OSPF uses a reference bandwidth of 100 Mbps for cost calculation. The formula to calculate the cost is the reference bandwidth divided by interface bandwidth.
BSR 2000 Command Reference Guide Release 1.0 auto-virtual-link Use the auto-virtual-link command to automatically detect and create OSPF virtual links. The no auto-virtual-link command disables automatic detection and creation of OSPF virtual links. Group Access ISP Command Mode Router Configuration Command Line Usage auto-virtual-link no auto-virtual-link Command Default Disabled 8-10 MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands clear ip ospf The clear ip ospf command resets an OSPF connection using a soft reconfiguration. Group Access All Command Mode All modes except User EXEC Command Line Usage clear ip ospf 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 default-information originate The default-information originate command generates a default route into an OSPF routing domain by configuring the metric for redistributed routes and is used with the redistribute command to redistribute routes into an OSPF routing domain so they are included in an automatic Autonomous System Border Router (ASBR) summary. The no default-information originate command removes default routes from the OSPF routing domain.
Release 1.0 OSPF Commands default-metric The default metric feature is used to eliminate the need for separate metric definitions for each routing protocol redistribution.The default-metric command forces the OSPF routing protocol to use the same metric value for all distributed routes from other routing protocols. The no default-metric command removes or changes the default metric value for the OSPF routing protocol.
BSR 2000 Command Reference Guide Release 1.0 distance The distance command sets all 3 OSPF distances for routes to the same administrative value. The no distance command disables the administrative distance for routes. Group Access ISP Command Mode Router Configuration Command Line Usage distance <1-255> no distance <1-255> Command Syntax 1-255 administrative distance for setting routes Command Default 120 8-14 MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands distance ospf The distance ospf command defines OSPF route administrative distances based on route type. The no distance ospf command deletes OSPF route administrative distances based on route type. Use the distance ospf command to set a distance for a group of routers, as opposed to any specific route passing an access list. The distance ospf command serves the same function as the distance command used with an access list.
BSR 2000 Command Reference Guide Release 1.0 Command Default intra-area distance = 110 inter-area distance = 110 external distance = 110 8-16 MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands distribute-list Use the distribute-list command to filter networks received and sent in routing updates and networks suppressed in routing updates by using access lists. The networks that are permitted or denied are defined in access lists. The no distribute-list command removes access list from an incoming or outgoing routing update.
BSR 2000 Command Reference Guide Release 1.0 ip ospf authentication-key The ip ospf authentication-key command assigns a password for use by neighboring OSPF routers that are using OSPF simple password authentication. The no ip ospf authentication-key command deletes the password assigned for use by neighboring OSPF routers that are using OSPF simple password authentication. Note: All neighbor routers on the same network need the same password to exchange OSPF information.
Release 1.0 OSPF Commands ip ospf cost The ip ospf cost command establishes a precise cost metric value for sending a packet on an OSPF interface. The no ip ospf cost command disables a precise cost metric value for sending the path cost to the default. Use the ip ospf cost command to assign a cost metric value for a particular interface. The user can set the metric manually if the default needs to be changed.
BSR 2000 Command Reference Guide Release 1.0 ip ospf database-filter all out The ip ospf database-filter all out command filters OSPF LSAs during synchronization and flooding on the specified interface. The no ip ospf database-filter all out command disables filtering OSPF LSAs during synchronization and flooding on the specified interface.
Release 1.0 OSPF Commands ip ospf dead-interval The ip ospf dead-interval command sets the number of seconds during which the router hello packets are not seen before the neighboring routers consider the router to be down. The no ip ospf dead-internal removes the number of seconds set during which the router hello packets are not seen before the neighboring routers consider the router to be down.
BSR 2000 Command Reference Guide Release 1.0 ip ospf hello-interval The ip ospf hello-interval command sets the number of seconds between hello packets send by a router on the interface. The no ip ospf hello-interval command resets the number of seconds between hello packets sent by a router on an interface to the default value. Use the ip ospf hello-interval command as a form of keepalive used by routers in order to acknowledge their existence on a segment.
Release 1.0 OSPF Commands ip ospf message-digest-key The ip ospf message-digest-key command enables OSPF MD5 authentication. The no ip ospf message-digest-key command disables OSPF MD5 authentication. Use the ip ospf message-digest-key md5 command to generate authentication information when sending packets and to authenticate incoming packets. Neighbor routers must have the same key identifier.
BSR 2000 Command Reference Guide Release 1.0 ip ospf network The ip ospf network command configures the OSPF network type to a type other than the default for a given media. The no ip ospf network command returns to the default network type.
Release 1.0 OSPF Commands ip ospf priority The ip ospf priority command sets router priority to aid in determining the OSPF designated router for a network. The no ip ospf priority command changes priority to aid in determining the OSPF designated router for a network to the default value. Use the ip ospf priority command value to configure OSPF broadcast networks. The router with a higher priority takes precedence when attempting to become the designated router.
BSR 2000 Command Reference Guide Release 1.0 ip ospf retransmit-interval The ip ospf retransmit-interval command establishes the number of seconds between LSAs retransmissions for adjacencies belonging to an OSPF interface. The no ip ospf retransmit-interval command changes the number of seconds between LSA retransmissions for adjacencies belonging to an OSPF interface to the default value. Use the ip ospf retransmit-interval command to establish the time a router sends an LSA to its neighbor.
Release 1.0 OSPF Commands ip ospf transmit-delay The ip ospf transmit-delay command sets the approximate amount of time to transmit an LSA retransmissions for adjacencies belonging to an OSPF interface. The no ip ospf transmit-delay command changes the approximate amount of time set to transmit an LSA retransmissions for adjacencies belonging to an OSPF interface. Use the ip ospf transmit-delay command to enable the delay over a link.
BSR 2000 Command Reference Guide Release 1.0 maximum-paths The maximum-paths command specifies the maximum number of parallel routes an IP routing protocol can support. The no maximum-paths command changes or cancels the number of maximum paths. Group Access RESTRICTED Command Mode Router Configuration Command Line Usage maximum-paths <1-2> no maximum-paths Command Syntax 1-2 8-28 the maximum number of parallel routes MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands network area The network area command defines the interfaces and area ID on which OSPF runs. The no network area command deletes the interfaces and area ID on which OSPF runs. Use the network area command to cover IP address(es) for OSPF to operate on an interface. Use the address and wildcard-mask as one command to define one or more interfaces for an intended area. A subnet address may be designated as the area ID if associated areas are used with IP subnets.
BSR 2000 Command Reference Guide Release 1.0 passive-interface The passive-interface command disables an interface from sending route updates by prohibiting packets from being transmitted from a specified port. When disabled, the subnet continues advertising to other interfaces. The no passive-interface command enables the interface to send route updates.
Release 1.0 OSPF Commands redistribute The redistribute command redistributes routes from one protocol domain to another routing domain. The no redistribute command disables route distribution from one protocol domain to another routing domain.
BSR 2000 Command Reference Guide Release 1.0 Command Default Disabled 8-32 MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands rfc1583-compatible The rfc1583-compatible enables RFC1583 preference rules on choosing AS-External-LSAs during shortest path first (SPF) calculation according to RFC2328, section 16.4. The no rfc1583-compatible command disables RFC1583 preference rules on choosing AS-External-LSAs during SPF calculation according to RFC2238, section 16.4.
BSR 2000 Command Reference Guide Release 1.0 router-id The router-id command overrides a configured OSPF router identifier (IP address) by manually configuring a new identifier. The no router-id command restores the initial configuration. Group Access ISP Command Mode Router Configuration Command Line Usage router-id no router-id Command Syntax A.B.C.D 8-34 the new OSPF router identifier (IP address) MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands router ospf The router ospf command enables an OSPF routing process. The no router ospf command disables the OSPF routing process. Use the router ospf command to designate an OSPF routing process with a unique value. Group Access ISP Command Mode Global Configuration Command Line Usage router ospf no router ospf 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip ospf To display general information about OSPF routing processes, use the show ip ospf command.
Release 1.0 OSPF Commands show ip ospf database The show ip ospf database command displays list of information related to the OSPF database. Group Access All Command Mode All Modes except User EXEC Command Line Usage show ip ospf [<0-4294967295>] database [A.B.C.D | adv-router | asbr-summary | database-summary | external | network | nssa-external | router | self-originate | summary] [ | {begin | exclude | include} {} [ | {count | count-only}]] show ip ospf [<0-4294967295>] database [A.
BSR 2000 Command Reference Guide 8-38 Release 1.
Release 1.0 OSPF Commands show ip ospf interface The show ip ospf interface command displays OSPF-related interface information. Group Access All Command Mode All Modes except User EXEC Command Line Usage show ip ospf interface [ | cable | ethernet | gigaether | loopback <1-64>] [ | {begin | exclude | include} {} [ | {count | count-only}]] show ip ospf interface [
BSR 2000 Command Reference Guide 8-40 Release 1.0 include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 OSPF Commands show ip ospf memory The show ip ospf memory command displays OSPF memory usage information.
BSR 2000 Command Reference Guide Release 1.0 show ip ospf neighbor The show ip ospf neighbor command displays information about all OSPF neighbors. Use the show ip ospf neighbor command to display information for each neighbor. Group Access ISP Command Mode All modes except User EXEC Command Line Usage show ip ospf neighbor [] [detail] [ | {begin | exclude | include} {} [ | {count | count-only}]] show ip ospf neighbor [
Release 1.0 OSPF Commands show ip ospf network The show ip ospf network command displays information about OSPF network areas.
BSR 2000 Command Reference Guide Release 1.0 show ip ospf virtual-links The show ip ospf virtual-links command displays parameters regarding the current state of the OSPF virtual links.
Release 1.0 OSPF Commands summary-address The summary-address aggregates external routes at the border of the OSPF domain. The no summary-address command deletes aggregated external routes at the border of the OSPF domain. Use the summary-address command to summarize routes from other routing protocols that are redistributed to OSPF. The area range command summarizes routes between OSPF areas.
BSR 2000 Command Reference Guide Release 1.0 timers spf The timers spf command configures the amount of time between OSPF topology change receipt and when it starts a shortest path first (SPF) calculation. This includes the hold time between two consecutive SPF calculations. The no timers spf command changes the configuration of the amount of time between OSPF topology changes receipt and when it starts an SPF calculation and returns it to the default value.
9 IGMP Commands Introduction This chapter describes the Internet Group Management Protocol (IGMP) commands used with the BSR 2000™. Internet Group Management Protocol (IGMP), part of the Internet Protocol (IP) suite, is used between hosts and routers to report dynamic multicast group membership. IP multicasting is the transmission of an IP datagram to a "host group" identified by a single IP destination address.
BSR 2000 Command Reference Guide Release 1.0 Applications that implement IGMP effectively eliminate multicast traffic on segments that are not destined to receive this traffic, thus limiting the overall amount of traffic on the network. IGMP Command Descriptions This section contains an alphabetized list and descriptions of the IGMP commands supported by the BSR. 9-2 MGBI 526363-001-00 Rev.
Release 1.0 IGMP Commands clear ip igmp counters The clear ip igmp counters command clears IGMP statistics counters on a specific router. Group Access ISP Command Mode All modes except User EXEC Command Line Usage clear ip igmp counters 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip igmp access-group The ip igmp access-group command controls multicast groups that hosts can join. The no ip igmp access-group command removes control and allows the hosts to join all groups.
Release 1.0 IGMP Commands ip igmp querier-timeout The ip igmp querier-interval command configures the timeout prior to the time the router takes over as the interface querier. The no ip igmp querier-timeout removes the configured timeout prior to the time the router takes over as the interface querier, and returns it to the default. Note: Only after the querier has completed the last query, does the router take over as the interface querier after a no ip igmp querier-timeout command is issued.
BSR 2000 Command Reference Guide Release 1.0 ip igmp query-interval The igmp query-interval command sets the interval in which the router sends out IGMP queries for that interface. The no ip igmp query-interval command removes the set interval in which the router send out IGMP queries for an interface and returns it to the default value. Use the ip igmp query-interval command to configure how often the router solicits the IGMP report responses from all of the multicast hosts on the network.
Release 1.0 IGMP Commands ip igmp query-max-response-time The ip igmp query-max-response-time command sets the maximum response time advertised in query. Use the no ip igmp query-max-response-time command to remove the set maximum response time advertised in query and return it to the default.
BSR 2000 Command Reference Guide Release 1.0 ip igmp static-group The ip igmp static-group command connects, or configures, the router as a member of a particular group on the interface. The no ip igmp static-group disassociates the router from the group. The ip igmp static-group command is used to give a host (that does not run IGMP) membership in a multicast group. Group Access ISP Command Mode Interface Configuration Command Line Usage ip igmp static-group no ip igmp static-group
Release 1.0 IGMP Commands ip igmp version The ip igmp version command configures the specific version used by the router. The no ip igmp version removes the configured, specific version used by the router and returns it to the default. Use the ip igmp version command to configure the IGMP version on the interface.
BSR 2000 Command Reference Guide Release 1.0 ip igmp version1-querier The ip igmp version1-querier command configures the router to act as the querier for IGMPv1. This is done by manually assigning the IGMP querier. The no ip igmp version1-querier command disables the router from acting as the querier. Note: The interface is not effected when IGMPv2 is running on the interface. It is recommended that only one querier is enabled in a network segment.
Release 1.0 IGMP Commands show ip igmp interface The show ip igmp interface command displays the multicast information for an interface.
BSR 2000 Command Reference Guide Release 1.0 show ip igmp groups The show ip igmp groups command displays multicast groups connected to a specific router using IGMP.
Release 1.0 IGMP Commands exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip igmp statistics The show ip igmp statistics command displays statistics for a specified IGMP interface.
10 IP Multicast Commands Introduction This chapter describes the IP Multicast Protocol commands used with the BSR. This chapter contains the following sections on the Multicast Routing Table Manager (MRTM), and Multicast Forwarding Manager (MFM) protocols. ■ MRTM Command Descriptions ■ MFM Command Descriptions MRTM Command Descriptions Unlike traditional Internet traffic that requires separate connections for each source-destination pair, IP Multicasting allows many recipients to share the same source.
BSR 2000 Command Reference Guide Release 1.0 ip mroute The ip mroute command configures an IP multicast static route. The no ip mroute command removes the configuration of an IP multicast static route. Group Access ISP Command Mode Global Configuration Command Line Usage ip mroute [<1-255>] no ip mroute [<1-255>] Command Syntax 10-2 A.B.C.D static source address A.B.C.D static network mask A.B.C.
Release 1.0 IP Multicast Commands ip mroute static distance The ip mroute static distance command configures a static multicast route. The no ip mroute static distance command removes the route. Group Access ISP Command Mode Global Configuration Command Line Usage ip mroute static distance <1-255> no ip mroute static distance <1-255> Command Syntax 1-255 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip mroute unicast distance The ip mroute unicast distance command configures a unicast multicast route. The no ip mroute unicast distance command removes the route. Group Access ISP Command Mode Global Configuration Command Line Usage ip mroute unicast distance <1-255> no ip mroute unicast distance <1-255> Command Syntax 1-255 10-4 the administrative distance for the multicast route - a lower distance has preference MGBI 526363-001-00 Rev.
Release 1.0 IP Multicast Commands ip multicast-routing The ip multicast-routing command enables IP multicast routing. The no ip multicast-routing command disables IP multicast routing. This command is used with multicast routing protocols. Note: Multicast packets are not forwarded unless IP multicast routing is enabled. Group Access ISP Command Mode Global Configuration Command Line Usage ip multicast-routing no ip multicast-routing Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip rpf The show ip rpf command displays how IP multicast routing does Reverse Path Forwarding (RPF). Group Access All Command Mode All modes except User EXEC Command Line Usage show ip rpf Command Syntax A.B.C.D displays RPF information for a specified source address MFM Command Descriptions MFM supports multicast tools for tracing routes, maintains a multicast forwarding cache and forwards multicast traffic.
Release 1.0 IP Multicast Commands clear ip multicast fwd-cache The clear ip multicast fwd-cache command clears the IP multicast forwarding cache table. Use the clear ip multicast fwd-cache command to clear the multicast forwarding table which is built from the multicast forwarding cache, and then used for forwarding traffic. Once cleared, the Multicast Forwarding Manager regenerates the cache when multicast traffic is received.
BSR 2000 Command Reference Guide Release 1.0 clear ip multicast proto-cache The clear ip multicast proto-cache command clears the IP multicast protocol cache and also clears the IP multicast forwarding cache. Note: The MFM manager regenerates the multicast protocol cache when multicast traffic is received. Group Access ISP Command Mode All modes except User EXEC Command Line Usage clear ip multicast proto-cache 10-8 MGBI 526363-001-00 Rev.
Release 1.0 IP Multicast Commands mtrace The mtrace command traces the path from a multicast source to a multicast destination branch of a multicast distribution tree. Group Access ISP Command Mode Privileged EXEC Command Line Usage mtrace { } Command Syntax A.B.C.D (group) group address or group hostname A.B.C.D (hostname) destination IP address or destination hostname A.B.C.
BSR 2000 Command Reference Guide Release 1.0 show ip multicast cache-summary The show ip multicast cache-summary command displays the number of multicast flows currently passing through the router. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip multicast cache-summary 10-10 MGBI 526363-001-00 Rev.
Release 1.0 IP Multicast Commands show ip multicast fwd-cache The show ip multicast fwd-cache command displays all of the multicast forwarding cache on a source group basis. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip multicast fwd-cache [] [] [ physical ] Command Syntax A.B.C.D only displays the cache for this source or group address A.B.C.
BSR 2000 Command Reference Guide Release 1.0 show ip multicast interface The show ip multicast interface command is used to list the IP address, multicast protocol (PIM or IGMP), and time-to-live (TTL) information that is associated with each multicast interface. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip multicast interface Command Syntax A.B.C.D 10-12 display information only for this interface address MGBI 526363-001-00 Rev.
Release 1.0 IP Multicast Commands show ip multicast oi-fwd-cache The show ip multicast oi-fwd-cache command is used to display multicast forwarding cache entries that have outgoing interfaces (OIs). Group Access ISP Command Mode All modes except User EXEC Command Line Usage show ip multicast oi-fwd-cache 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip multicast no-oi-fwd-cache The show ip multicast no-oi-fwd-cache command is used to display multicast forwarding cache entries, which have no outgoing interfaces (OIs). Group Access All Command Mode All modes except User EXEC Command Line Usage show ip multicast no-oi-fwd-cache 10-14 MGBI 526363-001-00 Rev.
Release 1.0 IP Multicast Commands show ip multicast proto-cache The show ip multicast proto-cache command is used to display multicast protocol cache entries. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip multicast proto-cache [] [] Command Syntax A.B.C.D only displays the cache for this source or group address A.B.C.D only displays the cache for this specified source and group address 526363-001-00 Rev.
11 CMTS Commands Introduction This chapter describes the commands used to configure and manage the Cable Modem Termination System (CMTS). The CMTS permits data to be transmitted and received over a broadband cable TV (CATV) network. Downstream network data traffic flows from the CMTS to connected cable modems (CMs), and upstream network data traffic flows from the CMs to the CMTS.
BSR 2000 Command Reference Guide Release 1.0 arp timeout The arp timeout command configures the amount of time an entry stays in the ARP cache. The no arp timeout command removes the time configuration an entry stays in the ARP cache. Use the show interfaces command in Privileged EXEC mode to view the ARP time-out value. Note: If the ARP time-out value is changed, the new value affects all the existing entries in the ARP cache and any entries subsequently added to the ARP cache.
Release 1.0 CMTS Commands band The band command is used to define the start and end frequency band for the Spectrum Group. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage North American DOCSIS band <5000000-42000000> <5000000-42000000> no band <5000000-42000000> <5000000-42000000> Euro-DOCSIS band <5000000-42000000> <5000000-65000000> no band <5000000-42000000> <5000000-65000000> Command Syntax 5000000-42000000 The start upstream frequency in Hertz for DOCSIS.
BSR 2000 Command Reference Guide Release 1.0 cable cmts type The cable cmts type command specifies the DOCSIS type supported by all CMTS modules resident in the BSR chassis.
Release 1.0 CMTS Commands cable concatenation The cable concatenation command enables or disables concatenation for DOCSIS 1.0 or DOCSIS 1.1 cable modems. The no cable concatenation command restores the default setting. Note: Concatenation must be enabled globally with the cable upstream concatenation command before any setting specified with the cable concatenation command is valid. Once concatenation is enabled globally, the cable concatenation command will enable or disable concatentation for DOCSIS 1.
BSR 2000 Command Reference Guide Release 1.0 cable deny ip The cable deny ip command allows operators to filter (drop) worm/virus packets on both the upstream and downstream cable interfaces by specifying the IP protocol used by the virus or worm and its packet length (in bytes) to enable a filter for a particular threat. The no cable deny ip command disables the filter.
Release 1.0 CMTS Commands cable dhcp-giaddr primary This cable dhcp-giaddr primary command forces the BSR to always set the giaddr in host DHCP requests to the primary cable interface IP address. The no cable dhcp-giaddr primary command sets the giaddr field in DHCP host requests to the default. When set to the default, the first secondary address, if one is defined, is used in DHCP host requests, otherwise the primary IP address is used.
BSR 2000 Command Reference Guide Release 1.0 cable downstream carrier-only The downstream carrier-only function is disabled by default and is used for testing purposes only to control downstream output. The cable downstream carrier-only command is used optionally as a test function to enable the modulation to the RF carrier of the downstream output. The no cable downstream carrier-only command disables the modulation to the RF carrier of the downstream output.
Release 1.0 CMTS Commands cable downstream description The cable downstream description command is used to specify descriptive information for a downstream port on the BSR. This information is limited to 80 characters and single word descriptions are not allowed. Use the characters: _ or - to separate words.
BSR 2000 Command Reference Guide Release 1.0 cable downstream frequency The cable downstream frequency command is used to set the fixed center downstream frequency for RF output. The no cable downstream command returns the fixed center downstream frequency of RF output to the default.. Note: The Japan DOCSIS Standard must be specified with the cable cmts type command before a downstream frequency can be selected for any Japan DOCSIS Standard CMTS module.
Release 1.0 CMTS Commands Command Syntax 0-0 Downstream port number. 91000000-857000000 The downstream carrier center frequency. Valid values are from 91000000 to 857000000 Hertz (Hz) for North American DOCSIS. 112000000-858000000 The downstream carrier center frequency. Valid values are from 112000000 to 858000000 Hz for EuroDOCSIS. 91000000-860000000 The downstream carrier center frequency for the Japan DOCSIS (J-DOCSIS) Standard Command Default 555000000 Hz 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable downstream interleave-depth The cable operator can protect the downstream path from excess noise or decrease latency on the downstream path by setting the interleave depth. A higher interleave depth provides more protection from noise on the HFC network, but increases downstream latency. A lower interleave depth decreases downstream latency, but provides less protection from noise on the HFC network.
Release 1.0 CMTS Commands Table 11-1 Interleave Depth Criteria Depth # of Taps Increments 32 32 4 64 64 2 128 128 1 Note: The Euro DOCSIS standard requires an interleave depth of 12. Command Default The command default is 8 for North American DOCSIS. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable downstream modulation The cable downstream modulation command sets the modulation rate for a downstream port. The no cable downstream modulation command returns the modulation rate setting to the default. Group Access MSO Command Mode Interface Configuration (cable interface only) Command Line Usage cable downstream [<0-0>] modulation {256 | 64} no cable downstream [<0-0>] modulation {256 | 64} Command Syntax 0-0 Downstream port number.
Release 1.0 CMTS Commands cable downstream power-level The cable downstream power-level command sets the power level of a downstream channel. The no cable downstream power-level changes the power level setting of a downstream channel to the default. Use the cable downstream power-level command to set the absolute power level in tenths of dBmV. Use cable downstream power-level default setting to set the receive power based on the automatic calculation of the necessary power level.
BSR 2000 Command Reference Guide Release 1.0 cable downstream pre-equalization The cable downstream pre-equalization command enables pre-equalization adjustment on the downstream port that includes sending pre-equalization coefficients in a ranging response to a CM to compensate for impairment over the transmission line. The no cable downstream pre-equalization command disables the pre-equalization function. Note: Not all CMs support the pre-equalization adjustment.
Release 1.0 CMTS Commands cable downstream rate-limit The cable downstream rate-limit command controls whether rate limiting is applied to downstream traffic on a given downstream interface. The no cable upstream rate-limit command disables downstream rate limiting. The token-bucket algorithm is used for rate limiting. Note: If the rate-limit is enabled, downstream traffic is rate-limited according to the cable modems configured.
BSR 2000 Command Reference Guide Release 1.0 cable downstream schedule The cable downstream schedule command is used to configure the type of scheduling to be applied on downstream ports.
Release 1.0 CMTS Commands cable downstream scrambler on The cable downstream scrambler on command enables the scrambler for a downstream port. The no cable downstream scrambler on command disables the scrambler for a downstream port. Group Access All Command Mode Interface Configuration (cable interface only) Command Line Usage cable downstream scrambler on no cable downstream scrambler on Command Syntax NUM 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable downstream shutdown The cable downstream shutdown command is used to disable an enabled downstream port when certain downstream parameters require that the downstream port is disabled before these parameters are configured. The downstream port is disabled by default. Use the no cable downstream shutdown command to enable the downstream port after the required downstream parameters are configured for the BSR.
Release 1.0 CMTS Commands cable downstream threshold The cable downstream threshold command specifies downstream channel upper and lower queue thresholds. This command allows an operator to configure "back pressure" parameters for various applications.
BSR 2000 Command Reference Guide Release 1.0 Command Defaults upper byte threshold = 1000 bytes lower byte threshold = 500 bytes upper pdu threshold = 32 PDUs lower pdu threshold = 16 PDUs 11-22 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable downstream trap-enable-if The cable downstream trap-enable-if command enables the ifLinkUpDownTrapEnable trap for a downstream channel. The ifLinkUpDownTrapEnable trap indicates whether a link up or link down trap should be generated. The cable downstream no trap-enable-if command disables the ifLinkUpDownTrapEnable trap.
BSR 2000 Command Reference Guide Release 1.0 cable downstream trap-enable-rdn The cable downstream trap-enable-rdn command enables the rdnCardIfLinkUpDownEnable trap for a downstream channel. The rdnCardIfLinkUpDownEnable trap indicates whether a link up or link down trap should be generated. The no cable downstream trap-enable-rdn command disables the rdnCardIfLinkUpDownEnable trap.
Release 1.0 CMTS Commands cable flap-list aging The cable flap-list aging command specifies the cable flap-list aging in terms of maximum number of minutes a cable modem is kept in the flap-list. Use the no cable flap-list aging command to disable cable flap-list aging. Use this command to keep track of cable modem mac address upstream and downstream traffic for every cable modem having communication problems. Problems can be detected when the cable is inactive.
BSR 2000 Command Reference Guide Release 1.0 Command Default 1440 minutes 11-26 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable flap-list insertion-time The cable flap-list insertion-time command sets the insertion time interval in seconds. Use the no form of this command to disable insertion time. Use the cable flap-list insertion-time command to manage the flapping modem detector and place the cable modem on the flap list if the connection time is outside the insertion time interval. Note: The insertion-time is the time taken by cable modems to complete their registration.
BSR 2000 Command Reference Guide Release 1.0 cable flap-list miss-threshold The cable flap-list miss-threshold command specifies the threshold for missing consecutive polling messages which triggers the polling flap detector. The no cable flap-list miss-threshold removes the specified threshold.
Release 1.0 CMTS Commands cable flap-list percentage-threshold The cable flap-list percentage-threshold command specifies the CM miss percentage threshold. The no cable flap-list percentage-threshold command restores the default threshold value. If CM miss percentage exceeds the flapListPercentageThreshold and the flapListTrap is enabled with the cable flap-list trap-enable command, a flapListTrap will be sent to the CMTS by the SNMP agent.
BSR 2000 Command Reference Guide Release 1.0 cable flap-list power-adjust threshold The cable flap-list power-adjust threshold specifies the flap-list power adjustment parameters in dBmV for recording a flap-list event. The no cable flap-list power-adjust threshold command disables power-adjust thresholds. Use the cable flap-list power-adjust threshold to manage the flapping modem detector and place the cable modem on the flap-list if the connection exceeds the parameters.
Release 1.0 CMTS Commands cable flap-list size The cable flap-list size command specifies the flap-list size, the maximum number of cable modems in the flap-list. The no cable flap-list size command sets the default flap-list table size. Use the cable flap-list size number command to set the number of modems that the cable flap-list table can record.
BSR 2000 Command Reference Guide Release 1.0 cable flap-list trap-enable The cable flap-list trap-enable command controls whether a flapListTrap will be sent to the CMTS by the SNMP agent if the CM miss percentage exceeds the flapListPercentageThreshold specified with the cable flap-list percentage-threshold command. The no cable flap-list percentage-threshold command disables sending the flapListTrap.
Release 1.0 CMTS Commands cable helper-address The cable helper address function disassembles a DHCP broadcast packet, and reassembles it into a unicast packet so that the packet can traverse the router and communicate with the DHCP server. The cable helper-address command enables broadcast forwarding for User Datagram Protocol (UDP) packets.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax 11-34 A.B.C.D the IP address of the destination DHCP server. cable-modem specifies that only CM UDP broadcasts are forwarded. host specifies that only CPE UDP broadcasts are forwarded. mta specifies that only CPE MTA broadcasts are forwarded. isp-bind A.B.C.D specifies the secondary IP subnet to which the cable-helper is bound. MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable host authorization range The cable host authorization range command configures an authorization IP address range for Customer Premise’s Equipment (CPE) access to the BSR. The no cable host authorization range command disables IP address range authorization.
BSR 2000 Command Reference Guide Release 1.0 cable insert-interval The cable insert-interval command sets the interval at which Initial Maintenance intervals are scheduled in the upstream.These intervals are used by cable modems to send ranging request messages when attempting to join the network. The no cable insert-interval command is used to set the default insertion interval. Note: Ensure that the upstream port is down before setting the insertion interval.
Release 1.0 CMTS Commands cable intercept The BSR provides a way to monitor and intercept data originating from a DOCSIS network through the Cable Intercept feature, which provides Multiple System Operators (MSOs) with Lawful Intercept capabilities required by the Communications Assistance for Law Enforcement Act (CALEA) for electronic surveillance. Lawful Intercept capabilities are used by law enforcement agencies to conduct electronic surveillance of circuit and data communications.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax mac The intercept source, which is the MAC address from which traffic is intercepted. Packets with a source or destination MAC address that matches this address are copied and forwarded to the data collection server. Most often, this MAC address is the user's CPE device (such as a PC or VoIP phone), and not the MAC address of the user's CM.
Release 1.0 CMTS Commands cable modem-aging-timer The cable modem-aging-timer command specifies a cable modem aging timer in minutes. Cable modems that go off-line are automatically removed from the network after the configured time period.
BSR 2000 Command Reference Guide Release 1.0 cable modem dcc The cable modem dcc command allows an operator to manually move DOCSIS 1.1 and 2.0 cable modems ot MTAs to a specified upstream and/or downstream port and logical channel using DOCSIS Dynamic Channel Change (DCC). Note: The upstream channel must be physically connected for DOCSIS 1.1 and 2.0 cable modems to be manually moved.
Release 1.0 CMTS Commands upstream 0-7/0-3 the upstream port/logical channel init-tech 0-4 the ranging technique used for DCC: 0 = re-initialize the MAC 1 = perform broadcast intitial ranging on the new channel before normal operation 2 = perform unicast ranging on the new channel before normal operation 3 = perform either broadcast or unicast ranging on the new channel before normal operation 4 = use the new channel directly without re-intializing or ranging 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable modem qos dsa The cable modem qos dsa command triggers a dynamic service change (DSC) initiated by the CMTS for a specified cable modem. The DSC is in a binary file that conforms to the DOCSIS cable modem configuration file format. This configuration file is saved in the TFTP "boot" directory on a TFTP server with a known IP address.
Release 1.0 CMTS Commands Command Default none 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable modem qos dsc The cable modem qos dsc command triggers a Dynamic Service Change (DSC) initiated by the CMTS for a specified cable modem (CM).The cable modem qos dsc command triggers a dynamic service change (DSC) initiated by the CMTS for a specified cable modem. The definition of the dynamic service is defined in a binary file that conforms to the DOCSIS cable modem’s configuration file format.
Release 1.0 CMTS Commands cable modem qos dsd The cable modem qos dsd command triggers a dynamic service deletion (DSD) initiated by the CMTS for a specified service flow. Note: The cable modem qos dsd command should be used with extreme caution as the correct service-flow identifier must be specified. Group Access MSO Command Mode Privileged EXEC Command Line Usage cable modem qos dsd <1-262143> Command Syntax X/Y X is 0. Y is the CMTS port number.
BSR 2000 Command Reference Guide Release 1.0 cable modem max-hosts The cable modem max-hosts command sets the limit for the maximum Customer Premises Equipment (CPE) hosts behind a particular cable modem. The no cable modem max-hosts sets the limit to the default value. Group Access MSO Command Mode Privileged EXEC Command Line Usage cable modem { | } max-hosts <0-32> no cable modem { | } max-hosts <0-32> Command Syntax 11-46 mac Cable modem MAC address.
Release 1.0 CMTS Commands cable modem max-hosts-all The cable modem max-hosts-all command sets the limit for the maximum Customer Premises Equipment (CPE) hosts behind all cable modems on the network. The no cable modem max-hosts-all sets the limit to the default value. Group Access MSO Command Mode Global Configuration Command Line Usage cable modem max-hosts-all <0-32> no cable modem max-hosts-all <0-32> Command Syntax 0-32 526363-001-00 Rev. B Number of CPE hosts.
BSR 2000 Command Reference Guide Release 1.0 cable modem ucc The cable modem ucc command allows an operator to manually move a DOCSIS 1.0 or 1.1 CM or MTA to a different upstream channel within the same MAC domain. Note: The cable modem will not be moved if the old and new upstream channels are associated to two different Spectrum Groups.
Release 1.0 CMTS Commands init-tech 0-4 the ranging technique used for UCC: 0 = re-initialize the MAC 1 = perform broadcast intitial ranging on the new channel before normal operation 2 = perform unicast ranging on the new channel before normal operation 3 = perform either broadcast or unicast ranging on the new channel before normal operation 4 = use the new channel directly without re-intializing or ranging logical 0-3 the upstream logical channel 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable modem updis The cable modem updis command enables the transmission of an an Upstream Transmitter Disable (UP-DIS) MAC layer message that disables a specified cable modem’s upstream transmitter. Upon receipt of an UP-DIS message, the cable modem autonomously disables its upstream transmitter. Once disabled through an UP-DIS message, the cable modem’s upstream transmitter can only be re-enabled by power cycling the cable modem.
Release 1.0 CMTS Commands cable modulation-profile The cable modulation-profile command navigates to Modulation Profile Configuration Mode. Modulation Profile Configuration Mode provides a series of modulation profile commands that allow an MSO to create or modify a modulation profile. Warning: Motorola does not recommend modification of modulation profile parameters without a thorough understanding of modulation changes and DOCSIS interface specifications.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 cable modulation-profile copy The cable modulation-profile copy command copies an existing modulation profile from a source modulation profile number to a destination modulation profile number. The destination modulation profile is overwritten by the source modulation profile.
Release 1.0 CMTS Commands cable modulation-profile reset The cable modulation-profile reset command resets a modified, pre-defined modulation profile back to the system default. Group Access MSO Command Mode Global Configuration Command Line Usage cable modulation-profile reset {<1-4> | <101-116> | <201-205> | <301-310>} Command Syntax 1-4, 101-116, 201-205, 301-310 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable multi-ds-override The cable multi-ds-override commands enables downstream frequency override during ranging. Downstream frequency override allows an MSO to instruct a cable modem to move to a specific downstream/upstream pair during ranging by sending an RNG-RSP message with a downstream frequency override that tells a specific cable modem to move to a specific downstream channel.
Release 1.0 CMTS Commands cable privacy auth life-time The cable privacy auth life-time command sets the authorization key (AK) life-time values for baseline privacy. The no cable privacy auth life-time command changes the AK life-time values for baseline privacy back to the default.
BSR 2000 Command Reference Guide Release 1.0 cable privacy cert The cable privacy cert command allows cable modems to register using self-signed manufacturer certificates, as opposed to a manufacturer certificate that is chained to the DOCSIS root certificate. The no cable privacy cert command disables this feature.
Release 1.0 CMTS Commands cable privacy cm-auth life-time The cable privacy cm-auth life-time command sets AK life-time values for a cable modem. The no cable privacy cm-auth life-time changes the setting of AK life-time values for a cable modem back to the default.
BSR 2000 Command Reference Guide Release 1.0 cable privacy cm-auth reset The cable privacy cm-auth reset command resets a Traffic Encryption Key (TEK) before expiration on a grace-time or a life-time value. The no cable privacy cm-auth reset command changes the TEK expiration back to the default.
Release 1.0 CMTS Commands cable privacy cm-tek life-time The cable privacy cm-tek life-time command sets the TEK life-time value for baseline privacy. The no cable privacy cm-tek life-time command returns the TEK life-time value to the default value. Group Access MSO Command Mode Interface Configuration Command Line Usage cable privacy cm-tek life-time <0-16383> <1800-604800> no cable privacy cm-tek life-time <0-16383> <1800-604800> Command Syntax 0-16383 CM primary SID.
BSR 2000 Command Reference Guide Release 1.0 cable privacy cm-tek reset The cable privacy cm-tek reset command resets a CM Traffic Encryption Key (TEK). Group Access MSO Command Mode Interface Configuration (cable interface only) Command Line Usage cable privacy cm-tek reset [<1-16383>] Command Syntax 1-16383 11-62 the primary Service Identifier (SID) of the cable modem MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable privacy mcast access The cable privacy mcast access command configures a multicast access list by specifying a cable modem MAC address and the corresponding multicast IP address. Note: A cable modem MAC address and the corresponding multicast IP address is required. Group Access MSO Command Mode Interface Configuration (cable interface only) Command Line Usage cable privacy mcast access Command Syntax H.H.
BSR 2000 Command Reference Guide Release 1.0 cable privacy tek life-time The cable privacy tek life-time command sets the cable privacy Traffic Encryption Key (TEK) life-time value. The no cable privacy tek life-time command returns the cable privacy TEK life-time value to the default value. Note: Baseline privacy is configured with key encryption keys (KEKs), and the TEKs are configured based on the 40 or 56-bit data encryption standard (DES).
Release 1.0 CMTS Commands cable qos-profile The cable qos-profile command accesses QoS Profile Configuration mode. QoS Profile Configuration mode allows you to create or modify a QoS Profile. The no cable qos-profile command deletes a QoS Profile.
BSR 2000 Command Reference Guide Release 1.0 cable shared-secret The cable shared-secret command activates or deactivates cable modem authentication with a shared-secret key. The no cable shared-secret command sets the cable shared-secret back to the default. Use the cable shared-secret command to authenticate the cable modem such that all cable modems must return a text string to register for access to the network.
Release 1.0 CMTS Commands cable shared-secondary-secret The cable shared-secondary-secret command activates or deactivates cable modem authentication with a shared-secondary-secret key. The no cable shared-secondary-secret command sets the cable shared-secondary-secret back to the default. Use the cable shared-secondary-secret command to authenticate the cable modem such that all cable modems must return a text string to register for access to the network.
BSR 2000 Command Reference Guide Release 1.0 cable spectrum-group The cable spectrum-group command is used to create a cable spectrum group and enter Cable Spectrum Group mode in which to configure a cable spectrum group. All of the cable spectrum parameters are configured from Cable Spectrum Group mode. Group Access MSO Command Mode Global Configuration Command Line Usage cable spectrum-group no cable spectrum-group Command Syntax WORD 11-68 The cable spectrum group name.
Release 1.0 CMTS Commands cable sync-interval The synchronization message interval is the interval between successive synchronization message transmissions from the BSR CMTS interface to the CMs. The cable sync-interval command sets the synchronization interval between transmission of successive SYNC messages from the CMTS to CMs. The no cable sync-interval returns the interval setting to transmit SYNC messages to the default.
BSR 2000 Command Reference Guide Release 1.0 cable ucd-interval The cable ucd-interval command sets the interval between transmission of successive Upstream Channel Descriptor (UCD) messages. The no cable ucd-interval changes the interval setting to transmit UCD messages back to the default. Note: Ensure that you disable the cable interface using the cable shutdown command before using the cable ucd-interval command.
Release 1.0 CMTS Commands cable upstream active-codes The cable upstream active-codes command specifies the number of active codes allowed for an S-CDMA channel type. The active codes value must be a non prime number. Increasing the number of allowed active codes provides more transmission channel capacity. Reducing the number of active codes takes advantage of the S-CDMA spreader processing gain at the expense of channel capacity.
BSR 2000 Command Reference Guide Release 1.0 cable upstream channel-type The cable upstream channel-type command allows you to specify the channel type for the default upstream channel (0) or specify the channel type for up to four logical channels (0-3).
Release 1.0 CMTS Commands cable upstream channel-width The cable upstream channel-width command specifies an upstream channel width for an upstream port. The no cable upstream channel-width command returns the default value.
BSR 2000 Command Reference Guide Release 1.0 cable upstream codes-minislot The cable upstream codes-minislot command specifies the number of active codes allowed for each minislot on an S-CDMA channel. The number active codes allowed for each minislot determines the minislot capacity and sets the granularity of the upstream grants.
Release 1.0 CMTS Commands cable upstream concatenation The cable upstream concatenation command enables CMTS concatenation capabilities. The no cable upstream concatenation command disables CMTS concatenation capabilities. Note: Concatenation must be enabled globally with the cable upstream concatenation command before any setting specified with the cable concatenation command is valid.
BSR 2000 Command Reference Guide Release 1.0 cable upstream data-backoff Use the cable upstream data-backoff command sets data back-off value to assign automatic or fixed start and stop values. The no cable upstream data-backoff command returns to the default data back-off value. Note: The automatic setting is recommended.
Release 1.0 CMTS Commands cable upstream description The cable upstream description command is used to specify descriptive information for a upstream port on the BSR. This information is limited to 80 characters and single word descriptions are not allowed. Use the characters: _ or - to separate words.
BSR 2000 Command Reference Guide Release 1.0 cable upstream force-frag The cable upstream force-frag command is used as a traffic shaping tool that forces the CM to fragment large upstream packets.
Release 1.0 CMTS Commands cable upstream frequency The cable upstream frequency command sets the fixed frequency for the upstream cable port in Hz. The no cable upstream frequency command returns the default upstream frequency value. The cable interface does not operate until a fixed upstream frequency is set. The RF upstream frequency must comply with the expected CM output frequency.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax NUM Upstream port number 5000000-42000000 The upstream frequency value; valid entries are from 5000000 to 42000000 Hertz (Hz) for DOCSIS. 5000000-65000000 The upstream frequency value; valid entries are from 5000000 to 65000000 Hz for Euro-DOCSIS. 10000000-55000000 The upstream frequency value for the Japan DOCSIS (J-DOCSIS) Standard Command Default none 11-80 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable upstream hopping-seed The cable upstream hopping-seed command specifies the 15 bit S-CDMA hopping seed value used for the code hopping sequence initialization. Note: The logical channel must be disabled to specify a new hopping seed value.
BSR 2000 Command Reference Guide Release 1.0 cable upstream ingress-canceller enable The cable upstream ingress-canceller enable command enables the ingress canceller feature for an upstream cable port. Ingress cancellation is a DOCSIS 2.0 feature that protects against worst case plant impairments such as common path distortion (CPD), citizen band (CB), short-wave radio, and ham radio by opening unused portions of the upstream Spectrum.
Release 1.0 CMTS Commands cable upstream ingress-canceller idle-interval The cable upstream ingress-canceller idle-interval command configures the idle interval for the ingress canceller feature.
BSR 2000 Command Reference Guide Release 1.0 cable upstream invited-range-interval The cable upstream invited-range-interval command is used to define the amount of time in milliseconds allowed by the CMTS between ranging requests transmitted by the cable modem (CM). The no cable upstream invited-range-interval command returns to the default value.
Release 1.0 CMTS Commands cable upstream iuc11-grant-size The cable upstream iuc11-grant-size command specifies the size of the Interval Usage Code (IUC) 11 Advanced Unsolicited Grant burst descriptor when configuring a DOCSIS 2.0 upstream logical channel. Note: If a modulation profile for an upstream channel does not support IUC 11, the configuration of the IUC 11 byte size will be not be allowed.
BSR 2000 Command Reference Guide Release 1.0 cable upstream maintain-power-density on The cable upstream maintain-power-density on command enables the Maintain Power Spectral Density feature for each logical channel. If Maintain Power Spectral Density is enabled and the modulation rate is different from the previous UCD, the cable modem must change its transmit power level to keep the power spectral density as close as possible to what it was prior to the modulation rate change.
Release 1.0 CMTS Commands cable upstream map-interval The cable upstream map-interval command is used to determine the time interval in microseconds for bandwidth maps messages (MAP) to be used by the CM to allocate upstream time slots. The no cable upstream map-interval command resets the upstream interval to the default.
BSR 2000 Command Reference Guide Release 1.0 cable upstream max-calls The Maximum Assigned Bandwidth (MAB) feature is used on the cable interface to regulate the number of Voice-over-IP (VOIP) calls that are available on a particular upstream channel for Unsolicited Grant Service (UGS) and Unsolicited Grant Service with Activity Detection UGS-AD constant bit rate (CBR) data flows. A definitive limit on the number of voice calls ensures that bandwidth resources are not overused on an upstream channel.
Release 1.0 CMTS Commands cable upstream minislot-size Use the cable upstream minislot-size command to set the number of 6.25 microsecond ticks in each upstream minislot. The no cable upstream minislot-size command returns the minislot size to the default value.
BSR 2000 Command Reference Guide Release 1.0 cable upstream modem-ranging-delay The cable upstream modem-ranging-delay command specifies the maximum cable modem ranging delay in microseconds (usec). The ranging delay of a modem is the timing adjustment that would be sent to the modem if it were located next to the CMTS.
Release 1.0 CMTS Commands cable upstream modulation-profile The cable upstream modulation-profile is used to apply an upstream modulation profile to an upstream channel. The no cable upstream modulation-profile command returns the modulation profile to modulation profile 1.
BSR 2000 Command Reference Guide Release 1.0 cable upstream physical-delay The CMTS physical delay function is used to specify the maximum round-trip propagation delay between the CMTS and cable modems (CMs). The CMTS can optionally set the physical delay automatically. The cable upstream physical-delay command is used to set fixed or automatic physical delay parameters. You can use the following options to adjust the physical delay function: ■ ■ ■ A single fixed time can be set for physical delay.
Release 1.0 CMTS Commands 10-1600 Automatic minimum physical delay in microseconds - the default is 200 microseconds 10-1600 Automatic maximum physical delay in microseconds - the default is 1600 microseconds Command Default The fixed physical delay is 400 microseconds 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable upstream power-level The BSR CMTS interface controls CM output power levels to meet the desired CMTS upstream input power level. Input power level adjustments to an upstream port compensate for CMTS signal degradation between the optical receiver and the upstream RF port. The cable upstream power-level command is used to set the upstream input power level in absolute mode.
Release 1.0 CMTS Commands Group Access MSO Command Mode Interface Configuration (cable interface only) Command Line Usage cable upstream power-level <-160 - +290> no cable upstream power-level <-160 - +290> Command Syntax NUM Upstream port number -160 - +290 The input power level, expressed in tenths of a dB.
BSR 2000 Command Reference Guide Release 1.0 cable upstream power-level default The BSR CMTS interface controls CM output power levels to meet the desired CMTS upstream input power level. Input power level adjustments to an upstream port compensate for CMTS signal degradation between the optical receiver and the upstream RF port.
Release 1.0 CMTS Commands Command Line Usage cable upstream power-level default {<-150 - +150>} no cable upstream power-level default {<-150 - +150>} Command Syntax NUM Upstream port number -150 - +150 The number of dB above or below the default input power level. Command Default 0 dB Command Example The following example shows how to use the cable upstream power-level default command to set the input power level for a 3.
BSR 2000 Command Reference Guide Release 1.0 cable upstream pre-equalization The cable upstream pre-equalization command enables pre-equalization adjustment on the upstream port that includes sending pre-equalization coefficients in a ranging response to a CM to compensate for impairment over the transmission line. The no cable upstream pre-equalization command disables the pre-equalization function. Note: Not all CMs support the pre-equalization adjustment.
Release 1.0 CMTS Commands cable upstream range-backoff Use the cable upstream range-backoff command to set the start and end upstream range-backoff values for a CM or re-establish a CM if a power outage occurs. Use the no cable upstream range-backoff command return the ranging back-off default value. If you choose automatic, the system sets the upstream data-backoff start and end values.
BSR 2000 Command Reference Guide Release 1.0 cable upstream range-forced-continue The cable upstream range-forced-continue command forces a ranging response to continue for all CMs.
Release 1.0 CMTS Commands cable upstream range-power-override The cable upstream range-power-override command enables CM power adjustment. The no cable upstream range-power-override command disables CM power adjustment. Group Access MSO Command Mode Interface Configuration (cable interface only) Command Line Usage cable upstream range-power-override no cable upstream range-power-override Command Syntax NUM 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable upstream rate-limit The cable upstream rate-limit command controls whether rate-limiting is applied to any CM sending upstream data to the CMTS on a given upstream interface. The no cable upstream rate-limit command changes the rate limit applied to a cable modem sending upstream data to the CMTS back to the default which is disabled. The token-bucket algorithm is used for rate-limiting.
Release 1.0 CMTS Commands cable upstream snr-offset The cable upstream snr-offset command configures the display an SNR value with an offset. The offset can be configured for each upstream port up to a value of 100 (10 dB) in 10 (1 dB) increments. The offset value will be added to the SNR value when it is displayed with the show controllers and show interfaces cable upstream signal-quality CLI commands and through SNMP.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax NUM the upstream port number the offset value in increments of 10 (1 dB): 10 20 30 40 50 60 70 80 90 100 11-104 offset SNR value by 10 offset SNR value by 20 offset SNR value by 30 offset SNR value by 40 offset SNR value by 50 offset SNR value by 60 offset SNR value by 70 offset SNR value by 80 offset SNR value by 90 offset SNR value by 100 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands cable upstream spectrum-group The cable upstream spectrum-group command is used to apply a spectrum group to an upstream port. The no cable upstream spectrum-group command removes the spectrum group.
BSR 2000 Command Reference Guide Release 1.0 cable upstream shutdown The cable upstream shutdown command administratively disables the upstream port.The no cable upstream shutdown command enables an upstream port. Note: Ensure that each upstream port is enabled after the port is properly configured and ready for use.
Release 1.0 CMTS Commands cable upstream spread-interval The cable upstream spread-interval specifies the spreading interval for an S-CDMA frame. A spreading interval is the time that it takes to transmit one symbol per code across all 128 codes in an S-CDMA frame. The time duration of an S-CDMA frame is determined by a configurable number of spreading intervals and the signaling rate.
BSR 2000 Command Reference Guide Release 1.0 cable upstream trap-enable-cmts The cable upstream trap-enable-cmts command enables the rdnCmtsLinkUpDownTrapEnable trap for an upstream port. The rdnCmtsLinkUpDownTrapEnable trap indicates whether a CMTS link up or link down trap should be generated. The no cable upstream trap-enable-rdn command disables the rdnCmtsLinkUpDownTrapEnable trap.
Release 1.0 CMTS Commands cable upstream trap-enable-if The cable upstream trap-enable-if command enables the ifLinkUpDownTrapEnable trap for an upstream port. The ifLinkUpDownTrapEnable trap indicates whether a link up or link down trap should be generated. The cable upstream no trap-enable-if command disables the ifLinkUpDownTrapEnable trap.
BSR 2000 Command Reference Guide Release 1.0 cable upstream trap-enable-rdn The cable upstream trap-enable-rdn command enables the rdnCardIfLinkUpDownEnable trap for an upstream port. The rdnCardIfLinkUpDownEnable trap indicates whether a link up or link down trap should be generated. The no cable upstream trap-enable-rdn command disables the rdnCardIfLinkUpDownEnable trap.
Release 1.0 CMTS Commands cable utilization-interval The cable utilization-interval command specifies the upstream or downstream channel utilization calculation interval. The no cable utilization-interval returns the channel utilization calculation interval to the default value of "0" (disabled).
BSR 2000 Command Reference Guide Release 1.0 channel-type The channel-type command specifies the channel type for a modulation profile. There are four possible channel-types: ■ TDMA - DOCSIS 1.1 channel type ■ ATDMA - DOCSIS 2.0 channel type ■ MTDMA - DOCSIS 1.1 or DOCSIS 2.0 channel type ■ S-CDMA - DOCSIS 2.
Release 1.0 CMTS Commands clear cable dcc-stats The clear cable dcc-stats command clears all Dynamic Channel Change (DCC) statistics for all CMTS modules in the BSR chassis or a CMTS module in a specified slot. Group Access All Command Mode All modes except User EXEC Command Line Usage clear cable dcc-stats [] Command Syntax X/Y 526363-001-00 Rev. B X is 0. Y is the CMTS MAC domain.
BSR 2000 Command Reference Guide Release 1.0 clear cable flap-list The clear cable flap-list command clears the cable flap-list. You can either clear the flap-list of a specific cable modem by specifying its MAC address or clear the flap-lists of all the cable modems by using the all option. Group Access MSO Command Mode Privileged EXEC Command Line Usage clear cable flap-list { | all} Command Syntax 11-114 mac MAC address in the form of xxxx.xxxx.
Release 1.0 CMTS Commands clear cable modem The clear cable modem command is used to either clear the traffic counters or reset a single cable modem or all cable modems connected to the BSR. The clear cable modem command options can be used to do the following: ■ Clear or reset a single cable modem by using its MAC address. ■ Clear or reset specific group of cable modems. ■ Clear or reset a single cable modem by using its IP address. ■ Clear or reset all cable modems.
BSR 2000 Command Reference Guide Release 1.0 clear cable modem offline The clear cable modem offline command removes a cable modem from the list of offline cable modems.
Release 1.0 CMTS Commands clear cable qos svc-flow statistics The clear cable qos svc-flow statistics command clears all statistics relating to downstream rate-limiting for a particular service flow. This is the same information displayed with the show cable qos svc-flow statistics command. Group Access MSO Command Mode All modes except User EXEC Command Line Usage clear cable qos svc-flow statistics [] [<1-4292967295>] Command Syntax X/Y X is 0. Y is the CMTS port number.
BSR 2000 Command Reference Guide Release 1.0 clear cable ucc-stats The clear cable ucc-stats command clears all UCC statistics for all CMTS modules in the BSR chassis or a CMTS module in a specified slot. Group Access All Command Mode All modes except User EXEC Command Line Usage clear cable ucc-stats [] Command Syntax X/Y 11-118 X is 0. Y is the CMTS MAC domain. MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands clear counters cable The clear counters cable clears counters for a cable interface. Group Access All Command Mode All modes except User EXEC. Command Line Usage clear counters cable Command Syntax X/Y 526363-001-00 Rev. B X is 0. Y is the CMTS port number.
BSR 2000 Command Reference Guide Release 1.0 codes-subframe The codes-subframe command specifies the sub-frame size for an S-CDMA channel type. The sub-frame size establishes the boundaries over which interleaving is accomplished Group Access MSO Command Mode Modulation Profile Configuration Command Line Usage codes-subframe <1-128> no codes-subframe <1-128> Command Syntax 1-128 11-120 the sub-frame size MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands collect interval The collect interval command configures the interval rate at which data collection is performed by the spectrum manager. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage collect interval <60-65535> Command Syntax 60-65535 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 collect resolution The collect resolution command is used to configure the frequency resolution rate that the spectrum manager performs. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage collect resolution <200000-400000> Command Syntax 200000-400000 The resolution in Hertz. Command Default 200000 Hz 11-122 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands dhcp leasequery authorization on The dhcp leasequery authorization on command enables the exchange of DHCP lease query messages between the CMTS and a DHCP server. The no dhcp leasequery authorization on command disables this exchange. When an IP packet is either received from or destined to a Host/CPE which does not have an entry in the BSR’s DHCP Lease table, the DHCP Lease Query feature will attempt to identify the Host/CPE.
BSR 2000 Command Reference Guide Release 1.0 dhcp throttle on The dhcp throttle on command enables DHCP Rate Limiting for all CMs or CPEs. The no dhcp throttle on command disables DHCP Rate Limiting for all CMs or CPEs. Note: Once enabled for either CPEs, CMs, or both types of devices, rate limiting applies to all DHCP Request/Discover packets on a per device basis. The DHCP Rate Limiting feature does not support specifying a particular device for which rate limiting will be applied.
Release 1.0 CMTS Commands dhcp throttle window The dhcp throttle window command configures the rate of one DHCP Request/ Discover packet per number of seconds for a CM or CPE. The no dhcp throttle window command restores the DHCP Request/Discover packet rate per number of seconds to the default value for all CMs or CPEs. Note: DHCP Rate Limiting must be enabled with the dhcp throttle on command for a new DHCP Request/Discover packet rate limit setting (other than the default) to take effect.
BSR 2000 Command Reference Guide Release 1.0 differential-encoding on The differential-encoding on command specifies whether or not differential encoding is used in this modulation profile. Differential encoding is a technique where data is transmitted according to the phase change between two modulation symbols instead of by the absolute phase of a symbol. Differential encoding makes the absolute phase of the received signal insignificant and has the effect of doubling the BER for the same C/N.
Release 1.0 CMTS Commands docstest The docstest command globally enables or disables DOCSIS 2.0 test mode on the BSR through the DOCSIS 2.0 Testing MIB (SP-TestMIBv2.0-D02-030530). The DOCSIS 2.0 Testing MIB is used to test DOCSIS 2.0 protocol compliance through a set of objects used to manage DOCSIS 2.0 Cable Modem (CM) and Cable Modem Termination System (CMTS) programmable test features. Note: The DOCSIS 2.0 Testing MIB is considered to be an adjunct to the DOCSIS 2.
BSR 2000 Command Reference Guide Release 1.0 docstest type The docstest type command allows you to specifiy the type of DOCSIS 2.0 test to be used through a series of enumerated test modes. The enumerated test mode selected with the docstest type command corresponds to an integer "TYPE" field in the DOCSIS 2.0 Testing MIB’s CM/CMTS TLV Table. Note: DOCSIS 2.0 test mode must be enabled with the docstest enable command before a DOCSIS 2.0 test type can be specified.
Release 1.0 CMTS Commands fec-codeword This fec codeword command specifies the number of information bytes for each FEC codeword. Group Access MSO Command Mode Modulation Profile Configuration Command Line Usage fec-codeword <16-253> no fec-codeword <16-253> Command Syntax 16-253 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 fec-correction The fec-correction command specifies the number of bytes that can be corrected per Forward Error Correction (FEC) code word. This is the number of bytes that the FEC decoder can correct within a codeword. A FEC codeword consists of information and parity bytes for error correction. The number of parity bytes is equal to two times the number of correctable errors. The size of correctable errors is dictated by channel impairments.
Release 1.0 CMTS Commands fft display The fft display command displays the FFT power level measurement data to the console or telnet session in one of the two formats: table or graph (ASCII plot). Power level measurement data is retrieved either from an operational CMTS module or a file system. The user specifies a frequency range for which power level measurement data is to be displayed.
BSR 2000 Command Reference Guide Release 1.0 fft setup The fft setup command can be used to configure the FFT processor on the BCM3138/ BCM3140 chip set or to display the current FFT processor configuration. Group Access MSO Command Mode Privileged EXEC Command Line Usage fft setup [sample {<256-2048>} mode {Tap-in} window {blackman | blackman-harris | hamming | hanning | rectangular}] Command Syntax Slot/Port Slot is always 0 for the BSR 2000. Port is a valid upstream port number.
Release 1.0 CMTS Commands fft start The fft start command initiates the power level measurement using the FFT algorithm via the RF Sentry. Note: The sample, mode, and window arguments are optional with the fft start command but can be used to override the current FFT processor configuration specified with the fft setup command and initiate power level measurement with a new FFT processor configuration.
BSR 2000 Command Reference Guide Release 1.0 fft store The fft store command saves the latest FFT power level measurement data for a CMTS module to a file system. The user specifies a particular slot and port, the file system (NVRAM or Flash), and a file name without any extension to be used to store the FFT power level measurement data. An extension of ".fft" will be automatically added to the file name.
Release 1.0 CMTS Commands guard-band The guard-band command is used to define the minimum spectrum separation or spacing between upstream channels in the same spectrum group. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage guard-band {<0-37000000> | <0-60000000>} no guard-band {<0-37000000> | <0-60000000>} Command Syntax 0-37000000 The guard band separation size in Hertz for North America. 0-60000000 The guard band separation size in Hertz for Europe.
BSR 2000 Command Reference Guide Release 1.0 hop action band The hop action band command is used to determine the search order for each frequency band during the frequency hop action. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage hop action band <5000000-42000000> <5000000-42000000> [priority <1-255>] no hop action band <5000000-42000000> <5000000-42000000> [priority <1-255>] Command Syntax 5000000-42000000 The start upstream frequency band in Hertz.
Release 1.0 CMTS Commands hop action channel-width The hop action channel-width command is used to change the upstream channel-width setting before a frequency hop action. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage hop action channel-width {1600000 | 200000 | 3200000 | 400000 | 800000} [priority <1-255>] no hop action channel-width {1600000 | 200000 | 3200000 | 400000 | 800000} [priority <1-255>] Command Syntax The upstream channel width setting.
BSR 2000 Command Reference Guide Release 1.0 hop action frequency The hop action frequency command is used to determine the frequency search order for either discrete center frequencies or frequency bands during the frequency hop action.
Release 1.0 CMTS Commands hop action modulation-profile The hop action modulation-profile command is used to change the modulation profile setting before a frequency hop action. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage hop action modulation-profile <1-16> [priority <1-255>] no hop action modulation-profile <1-16> [priority <1-255>] Command Syntax 1-16 The modulation profile number. 1-255 The upstream band priority number.The lower number takes precedence.
BSR 2000 Command Reference Guide Release 1.0 hop action power-level The hop action power-level command is used to change the power-level setting before a frequency hop action.Table 11-4 describes how the upstream channel bandwidth corresponds to the input power-level range and default power-level range for a specific upstream channel.
Release 1.0 CMTS Commands default -150 - +150 The number in tenths of a dB above or below the default input power level. 1-255 The upstream band priority number.The lower number takes precedence. Command Default upstream band priority = 128 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 hop action roll-back The hop action roll-back command is used to return the upstream channel width or modulation profile setting, that was adjusted during a hop action, to the original configuration when upstream channel conditions improve. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage hop action roll-back no hop action roll-back Command Default Disabled 11-142 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands hop period The hop period command is used to prevent excessive frequency hops on an upstream port. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage hop period <30-3600> no hop period <30-3600> Command Syntax 30-3600 The rate at which the frequency hop takes place in seconds. Command Default 300 seconds 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 hop threshold flap A frequency hopping threshold is configured to prevent unnecessary frequency hops in instances when one or a minimal number of cable modems (CMs) lose their connection with the BSR. The frequency hopping threshold is determined by the percentage of CMs that lose their connectivity. The hop threshold flap command is used to trigger the hop threshold flap when a greater than a set percentage of CMs lose their connectivity.
Release 1.0 CMTS Commands interface cable The interface cable command is used to enter cable interface configuration mode. Group Access MSO Command Mode Global Configuration Command Line Usage interface cable Command Syntax X/Y 526363-001-00 Rev. B X is 0. Y is the CMTS port number.
BSR 2000 Command Reference Guide Release 1.0 interleaver-block-size The interleaver-block-size command specifies the interleaver block size for an ATDMA or MTDMA channel. Interleaving is a technique which improves the error correction of channel noise such as burst errors. The interleaver re-arranges transmitted data and distributes it among different interleaver blocks. At the receiver end, the interleaved data is arranged back into the original sequence by a de-interleaver.
Release 1.0 CMTS Commands interleaver-depth The interleaver-depth command specifies the interleaver depth for an ATDMA or MTDMA channel. This command sets the interleaver minimum latency. A higher interleaver depth provides more protection from bursts errors by spreading out the bits for each codeword over a greater transmission time. However, a higher depth also increases downstream latency, which may slow TCP/IP throughput for some configurations. DOCSIS 2.
BSR 2000 Command Reference Guide Release 1.0 interleaver-step-size The interleaver-step-size command specifies the interleaver step size for an S-CDMA channel. The interleaver step size is the amount time that symbols are dispersed in time within the frame due to interleaving .
Release 1.0 CMTS Commands ip address The ip address command configures a primary or secondary IP address for an interface or defines the Gateway IP address (giaddr) for Customer Premises Equipment (CPE), Multimedia Telephone Adapter (MTA), or cable modem DHCP requests. The no ip address command is used to remove an IP address from the interface. When configuring the cable interface IP address two additional options are supported; the host and mta options.
BSR 2000 Command Reference Guide Release 1.0 Note: You must configure a primary IP address before configuring a secondary IP address. Note: The host or mta optional parameters can be specified with a secondary IP address on a loopback interface. However, these parameters will have no effect unless the loopback interface is configured as a virtual cable bundle master.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 ip dhcp relay information option The IP DHCP relay function is used only when multiple subnetworks are configured on the same cable interface. The IP DHCP relay function gathers broadcast DHCP MAC discovery packets from a DHCP host, such as a CM or Customer Premises Equipment (CPE), and redirect the packets to their corresponding DHCP server or DHCP server profile if there is only one DHCP server.
Release 1.0 CMTS Commands iuc The iuc command is used to completely configure a modulation profile without having to enter individual IUC submodes.
BSR 2000 Command Reference Guide Release 1.0 last-codeword-length The last-codeword-length command specifies fixed or shortened handling of FEC for last code word. Group Access MSO Command Mode Modulation Profile Configuration Command Line Usage last-codeword-length {fixed | shortened} no last-codeword-length {fixed | shortened} Command Syntax 11-154 fixed fixed handling of FEC for last code word shortened shortened handling of FEC for last code word MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands load-balancing static Static upstream load balancing evenly distributes cable modems across multiple upstream channels serving the same geographical community or Spectrum Group. Load balancing is based on the cable modem count on each upstream channel. Static load balancing means that the BSR will only attempt to move a cable modem to another upstream channel after the modem’s registration process is complete.
BSR 2000 Command Reference Guide Release 1.0 max-burst The max-burst command is used to specify the maximum burst length in minislots. The maximum burst length is used to determine the breakpoint between packets that use the short data grant burst profile and packets that use the long data grant burst profile. If the required upstream time to transmit a packet is greater than this value, the long data grant burst profile is used.
Release 1.0 CMTS Commands modulation-type The modulation-type command specifies the digital frequency modulation technique used in a modulation profile. ■ ■ Quadrature Phase Shift Keying (QPSK) is a digital frequency modulation technique is used primarily for sending data from the cable subscriber upstream. Quadrature Amplitude Modulation (QAM) is a digital frequency modulation technique is primarily used for sending data downstream.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax qpsk 16qam 8qam 32qam 64qam 128qam 256qam qpsk creates a default QPSK modulation type where all bursts are sent using QPSK 16qam creates a default 16-QAM modulation type where all bursts are sent using 16-QAM 8qam is used for DOCSIS 2.0 ATDMA or S-CDMA channel types only - creates a default 8-QAM modulation type where all bursts are sent using 8-QAM 32qam is used for DOCSIS 2.
Release 1.0 CMTS Commands ping docsis The ping docsis command is used to “ping” a cable modem (CM) on the network at the MAC layer to determine if the CM is online by entering the CM’s MAC or IP address. When a DOCSIS ping is initiated, the BSR sends a test packet downstream towards the CM to test its connection. In most instances, this command is used to determine if a particular CM is able to communicate at the MAC address layer when a cable modem has connectivity problems at the network layer.
BSR 2000 Command Reference Guide Release 1.0 preamble-length The preamble-length command is used to specify the preamble length in bits. The preamble length is used to define a synchronizing string of modulation symbols that is used to allow the receiver to find the phase and timing of the transmitted burst.
Release 1.0 CMTS Commands preamble-type The preamble-type command specifies the preamble format for DOCSIS ATDMA. MTDMA, and S-CDMA channel type modulation profiles. The preamble format is specified through the Quadrature Phase-Shift Keying (QPSK) digital modulation technique.
BSR 2000 Command Reference Guide Release 1.0 scrambler-mode The scrambler-mode command enables or disables the scrambler. The scrambler is used to generate an almost random sequence of transmission symbols. This ensures an even distribution of transmissions through the channel.
Release 1.0 CMTS Commands scrambler-seed The scramber-seed command specifies a scrambler seed value as a hexidecimal number. The scrambler seed is the initial value that is used to start the scrambler’s pseudo-randomizer to scramble the bits. As the transmitter and receiver know the scrambler seed value, scrambling can be reversed at the receiver leaving only the original data.
BSR 2000 Command Reference Guide Release 1.0 show cable dcc-stats The show cable dcc-stats command displays DOCSIS Dynamic Channel Change (DCC) statistics for a MAC domain.
Release 1.0 CMTS Commands Command Line Usage show cable dcc-stats [] Command Syntax X/Y 526363-001-00 Rev. B X is 0. Y is the CMTS MAC domain.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands Group Access All Command Mode Interface Configuration Command Line Usage show cable downstream [<0-0>] Command Syntax 0-0 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable flap-list The show cable flap-list command displays the cable flap-list and provides the following information:. 11-168 MAC ID Customer account or street address. Cable IF Upstream port. Hit Number of times modem responds to mac layer keep alive messages, minimum hit rate one time/30 seconds, can indicate intermittent upstream, laser clipping, or common-path distortion.
Release 1.0 CMTS Commands Type Specifies the type of flap (ranging, timing, or power) Time Most recent time modem dropped connection. The following is an example of typical screen output from the show cable flap-list command: MAC ID CableIF Hit Miss 000b.0643.3b60 4/0 U1 1469 7 000b.0643.36c8 4/0 U1 1469 7 000b.0643.
BSR 2000 Command Reference Guide Release 1.0 show cable insert-interval The show cable insert-interval command shows the period (in hundredths of a second) with which Initial Maintenance intervals are scheduled in the upstream. The following is an example of typical screen output from the show cable insert-interval command: Cable insert-interval: 20 Group Access All Command Mode Interface Configuration Command Line Usage show cable insert-interval 11-170 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable modem The show cable modem command is used to gather a variety of cable modem (CM) statistical information used to evaluate network performance, troubleshoot registration problems, and learn specific registration and ranging information on modems connected to a specific interface. Use the show cable modem command to see detailed modem configuration information for a specific head-end modem.
BSR 2000 Command Reference Guide Release 1.0 dhcp(d) DHCP Discover was sent by CM. dhcp(o) DHCP Offer was received. dhcp(req) DHCP Request was sent by CM. dhcp(ack) DHCP Ack was received, IP address was assigned by DHCP server. online CM registered; enabled for data. online(d) CM registered, but network access for the CM is disabled. online(un) CM registered, but not enabled data. Fail to verify modem's identity by BPI module.
Release 1.0 CMTS Commands Interface Cable Cable Cable Cable Cable Cable Cable Cable Cable 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 4/1/D1U1 Prim Sid 5 1 4 3 9 7 8 10 2 Connect State online(pt) online(pt) online(pt) online(pt) online(pt) online(pt) online(pt) online(pt) online(pt) Timing Offset 572 573 576 586 581 573 581 583 578 Rec Power 0.0 -.2 0.0 0.0 0.2 0.3 0.3 0.1 0.3 Ip Address Mac Address 150.31.101.14 150.31.101.44 150.31.101.45 150.31.101.46 150.31.101.
BSR 2000 Command Reference Guide 11-174 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Command Line Usage show cable modem cpe [ | {begin | exclude | include} {} [ | {count | count-only}] ] show cable modem cpe [ | {count | count-only}] show cable modem cpe [upstream ] [ | {begin | exclude | include} {} [ | {count | count-only}]] show cable modem cpe [upstream ] [ | {count | count-only}] Command Syntax 11-176 mac the cable modem’s MAC address X/Y X is 0. Y is the CMTS port number.
Release 1.0 CMTS Commands show cable modem detail The show cable modem detail command displays information for a SID assigned to a cable modem on a specific CMTS interface or a specific CM connected to a specific interface. The QoS Profile the cable modem used for registration is displayed in the "QoS Profile Index" field. The device type is displayed in the device type field: CM = cable modem, eSTB = embedded Set Top Box. The following is typical output from the show cable modem detail command.
BSR 2000 Command Reference Guide Release 1.0 CM Record (index 1) Dump: Psid 1 Config 0x2 Status regComplete BPI Enabled No MAC Address 0012.2503.52ac IP Addr 150.31.83.
Release 1.0 CMTS Commands Group Access All Command Mode All modes except User EXEC Command Line Usage show cable modem detail { } {} [ | {begin | exclude | include} {} [ | {count | count-only}]] show cable modem detail { } {} [ | {count | count-only}] Command Syntax X/Y X is 0. Y is the CMTS port number. NUM The Service Identifier assigned to a CM. MAC The cable modem’s MAC address.
BSR 2000 Command Reference Guide Release 1.0 show cable modem hosts The show cable modem hosts command displays the number of Customer Premises Equipment (CPE) hosts connected to a specific CM. MAC Address MAC State 0090.833d.bba0 online Prim Ver Frag Concat PHS Priv SID 6 DOC1.
Release 1.0 CMTS Commands count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable modem loadbalance-group The show cable modem loadbalance-group command displays cable modem load balancing group assignments. The following is typical output from the show cable modem loadbalance-group command: Cable Interface Cable 1/0/D0/U0/C0 Cable 1/0/D0/U1/C0 Cable 1/0/D0/U3/C0 Cable 1/0/D0/U3/C0 Cable 1/0/D0/U0/C0 Cable 1/0/D0/U1/C0 Mac Address 0008.0e10.3cb2 0010.1848.2004 0010.9518.f403 0012.c90b.cff8 0020.4094.e238 0050.04b2.
Release 1.0 CMTS Commands count-only count the number of lines while suppressing screen output exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands DS Saids the number of BPI+ style downstream Security Association Identifiers (SAIDs) that this cable modem supports (DOCSIS 1.1 modems only) US Sids the number of upstream Service IDentifiers (SIDs) that this cable modem supports (DOCSIS 1.1 modems only) Dev. the device type field: CM = cable modem eSTB = embedded Set Top Box If the cable modem supports DOCSIS 1.0+, it will be displayed in the "Version" field of the command output.
BSR 2000 Command Reference Guide Release 1.0 Command Line Usage show cable modem mac [ | {begin | exclude | include} {} [ | {count | count-only}]] show cable modem mac [ | {count | count-only}] show cable modem mac [ ] [ | {begin | exclude | include} {} [ | {count | count-only}]] show cable modem mac [] [ | {count | count-only}] Command Syntax 11-186 mac the cable modem’s MAC address X/Y X is 0. Y is the CMTS port number.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide 11-190 Release 1.0 begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide MAC Address 0008.0e10.3cb2 0010.1848.2004 0010.9518.f403 0012.c90b.cff8 0020.4094.e238 0050.04b2.f8e0 Release 1.
Release 1.0 CMTS Commands count-only count the number of lines while suppressing screen output exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable modem registered The show cable modem registered command displays the following information about registered cable modems: Interface cable modem interface with active connection Prim Sid Primary Service Identifier number Connect State describes the connectivity state of a cable modem. The table below describes the 20 cable modem connectivity states supported on the BSR Timing Offset current cable modem timing adjustment.
Release 1.0 CMTS Commands online(un) CM registered, but not enabled data. Fail to verify modem's identity by BPI module. online(pk) CM registered; baseline privacy interface (BPI) enabled, and key encryption key (KEK) is assigned. online(pt) CM registered; BPI enabled, and traffic encryption key (TEK) is assigned. reject(r) CM did attempt to register, registration was refused due to unavailable resource. reject(pk) KEK modem key assignment is rejected.
BSR 2000 Command Reference Guide 11-196 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable modem stats The show cable modem stats command displays the following statistics for each cable modem on a CMTS module. This includes cable modems that are off-line. Interface cable modem interface with active connection Prim Sid Primary Service Identifier number Connect State describes the connectivity state of a cable modem. The table below describes the 20 cable modem connectivity states supported on the BSR.
BSR 2000 Command Reference Guide Release 1.0 dhcp(ack) DHCP Ack was received, IP address was assigned by DHCP server. init(o) option file transfer was started. init(t) Time-of-day (TOD) exchange was started. online CM registered; enabled for data. online(d) CM registered, but network access for the CM is disabled. online(un) CM registered, but not enabled data. Fail to verify modem's identity by BPI module.
Release 1.0 CMTS Commands show cable modem { | | } stats [ | {count | count-only}] Command Syntax X/Y X is 0. Y is the port number.
BSR 2000 Command Reference Guide Release 1.0 show cable modem summary The show cable modem summary command displays cable modem information for each cable interface on the BSR.
Release 1.0 CMTS Commands Group Access All Command Mode All modes except User EXEC Command Line Usage show cable modem summary [ [downstream {} | total ]] [ | {begin | exclude | include} {} [ | {count | count-only}]] show cable modem summary [ [downstream | total ]] [ | {count | count-only}] Command Syntax X/Y X is 0. Y is the port number.
BSR 2000 Command Reference Guide Release 1.0 show cable modem summary total The show cable modem summary total command displays cable modem information for each cable interface on the BSR.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable modem time-registered The show cable modem time-registered command displays how long a cable modem has been registered. This command can be used to specify individual cable modems, cable modems associated with a particular BSR 2000 chassis slot, or cable modems associated with a particular Spectrum Group.
Release 1.0 CMTS Commands reject(c) CM did attempt to register; registration was refused due to bad COS. reject(r) CM did attempt to register, registration was refused due to unavailable resource. reject(pk) KEK modem key assignment is rejected. reject(pt) TEK modem key assignment is rejected.
BSR 2000 Command Reference Guide 11-208 Release 1.0 WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable modem timing-offset This show cable modem timing-offset command allows the user to select which cable modems are displayed on the console based on their timing offset value. The timing offset stored at the cable modem is the accumulation of all the timing adjustments sent to the cable modem. The cable modem starts at an initial timing offset which takes into account the cable modem’s internal delays.
BSR 2000 Command Reference Guide Release 1.0 The following is typical output from the show cable modem timing-offset command: Interface Cable Cable Cable Cable Cable Prim Sid 4/1/D1U1 6 4/1/D1U1 9 4/1/D1U1 1 4/1/D1U1 2 4/1/D1U1 8 Connect State online(pt) online(pt) online(pt) online(pt) online(pt) Timing Offset 581 581 583 583 581 Rec Ip Address Power 0.1 150.31.101.44 0.1 150.31.101.45 0.3 150.31.101.21 0.1 150.31.101.17 0.0 150.31.101.15 Mac Address 000b.0643.3716 000b.0643.3b60 000b.0643.
Release 1.0 CMTS Commands reject(c) CM did attempt to register; registration was refused due to bad COS. reject(r) CM did attempt to register, registration was refused due to unavailable resource. reject(pk) KEK modem key assignment is rejected. reject(pt) TEK modem key assignment is rejected. offline CM is considered to be offline.
BSR 2000 Command Reference Guide 11-212 Release 1.0 include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable modem unregistered The show cable modem unregistered command displays the following information about unregistered cable modems: Interface cable modem interface with active connection Prim Sid Primary Service Identifier number Connect State describes the connectivity state of a cable modem. The table below describes the 20 cable modem connectivity states supported on the BSR.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands show cable modulation-profile The show cable modulation-profile command displays all configured modulation profiles on the BSR. A modulation profile contains six burst profiles sent out in a UCD message to configure CM transmit parameters.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands Command Mode All modes except User EXEC Command Line Usage show cable modulation-profile [<1-600> [<1-11>]] Command Syntax 1-600 the modulation profile number 1-11 a specific IUC code: 1 = Request Burst 3 = Initial Maintenance 4 = Station Maintenance 5 = Short Grant Burst 6 = Long Grant Burst 9 = Advanced PHY Short Data Grant 10 = Advanced PHY Long Data Grant 11 = Unsolicited Grant Service 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable modulation-profile brief The show cable modulation-profile brief command displays cursory information for all configured modulation profiles on the BSR.
Release 1.0 CMTS Commands show cable privacy auth The show cable privacy auth command displays the AK grace time and life time values, in seconds. The following is an example of typical screen output from the show cable privacy auth command: Interface Cable 0/0 Auth grace time: 600 Auth life time: 604800 Group Access All Command Mode All modes except User EXEC Command Line Usage show cable privacy auth 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable privacy cm-auth The show cable privacy cm-auth command displays baseline privacy (BPI) authorization key (AK) information for an individual cable modem (CM) using its MAC address. Group Access All Command Mode Interface Configuration (cable interface only) Command Line Usage show cable privacy cm-auth [] Command Syntax mac 11-220 Cable modem’s MAC address in the form of xxxx.xxxx.xxxx. MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable privacy cmts The show cable privacy cmts command displays all the baseline privacy statistics specified by the MIB for the cable interface.
BSR 2000 Command Reference Guide Release 1.0 show cable privacy tek The show cable privacy tek command shows Traffic Encryption Key (TEK) grace time and life-time values.
Release 1.0 CMTS Commands show cable qos profile The show cable qos profile command displays the following information for all QoS Profiles or a selected user configurable QoS Profile: Note: This command is only valid for DOCSIS 1.0, DOCSIS 1.0+, and Euro-DOCSIS 1.0 cable modems. Prof Idx the QoS Profile identifying number Pri the relative priority number assigned to upstream traffic by this QoS profile with 7 being the highest priority.
BSR 2000 Command Reference Guide Release 1.0 Tos Value the overwrite value substituted for the received TOS value.
Release 1.0 CMTS Commands Once all DOCSIS 1.0, DOCSIS 1.0+, and Euro-DOCSIS 1.0 cable modems have a a unique QoS Profile number, the display of the show cable qos profile command is accurate. Group Access All Command Mode All modes except User EXEC Command Line Usage show cable qos profile [ [<1-32> [mac]]] Note: The show cable qos profile command without any argumanets displays all user-configured QoS profiles on the BSR regardless of whether they are in use.
BSR 2000 Command Reference Guide Release 1.0 show cable qos svc-flow classifier A service flow classifier matches a packet to a service flow using a service flow reference. The service flow reference associates a packet classifier encoding with a service flow encoding to establish a SFID. Classifiers have the following features: ■ Classifiers are loosely ordered by priority. ■ Several classifiers can refer to the same service flow. ■ More than one classifier may have the same priority.
Release 1.0 CMTS Commands show cable qos svc-flow dynamic-stat The show cable qos svc-flow dynamic-stat command displays the statistics for dynamic service additions, deletions, and changes for both upstream and downstream service flows.
BSR 2000 Command Reference Guide Release 1.0 show cable qos svc-flow log The show cable qos svc-flow log command displays the time that the service flow was created or deleted, the total number of packets counted, and the MAC address of the cable modem (CM) that used the service flow. Group Access All Command Mode All modes except User EXEC Command Line Usage show cable qos svc-flow log 11-228 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable qos svc-flow param-set The show cable qos svc-flow param-set command displays parameter settings for all service classes configured on an individual CMTS slot and port or all CMTS modules on the BSR.
BSR 2000 Command Reference Guide Release 1.0 show cable qos svc-flow phs The show cable qos svc-flow phs command displays the payload header suppression (PHS) configured for an interface that is used for a specific service flow. Note: If the PHS is not specified, all PHS entries with the specified SFIDs are listed. Group Access All Command Mode All modes except User EXEC Command Line Usage show cable qos svc-flow phs [ [<1-4292967295> [<1-65535>]]] Command Syntax 11-230 X/Y X is 0.
Release 1.0 CMTS Commands show cable qos svc-flow statistics The show cable qos svc-flow statistics command is used to determine the number of dropped packets due to downstream rate-limiting for a particular service flow.
BSR 2000 Command Reference Guide Release 1.0 show cable qos svc-flow summary The show cable qos svc-flow summary command displays the service flow information, including the SID, and QoS parameters sets associated with the service flow.
Release 1.0 CMTS Commands show cable qos svc-flow upstream-stat The show cable qos svc-flow upstream-stat command is used to display the number of fragmented packets, incomplete fragmented packets, and the number of concatenated bursts counted on the service flow.
BSR 2000 Command Reference Guide Release 1.0 show cable spectrum-group The show cable spectrum-group command is used to verify if the spectrum group that you assigned is activated for the upstream port. The following is typical output from the show cable qos svc-flow spectrum-group command: Spectrum Group: sg1 Member channels: Schedule Id 1 Band (Mhz) 5.000 - 42.
Release 1.0 CMTS Commands show cable spectrum-group load-balance summary This show cable spectrum-group load-balance summary command displays a summary of cable modem distribution and load balancing statistics for the spectrum group.
BSR 2000 Command Reference Guide Release 1.0 show cable sync-interval The show cable sync-interval command shows the configured sync-interval value between CMTS transmission of successive SYNC messages. The following is an example of typical screen output from the show cable sync-interval command: Cable sync-interval: 10 Group Access All Command Mode Interface Configuration (cable interface only) Command Line Usage show cable sync-interval 11-236 MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable ucc-stats The show cable ucc-stats command displays DOCSIS Upstream Channel Change (UCC) statistics for a MAC domain.
BSR 2000 Command Reference Guide Release 1.0 Command Line Usage show cable ucc-stats [] Command Syntax X/Y 11-238 X is 0. Y is the CMTS port number. MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show cable ucd-interval The show cable usd-interval command shows configured ucd-interval between transmission of successive UCD messages. The following is an example of typical screen output from the show cable ucd-interval command: Cable ucd-interval: 1000 Group Access All Command Mode Interface Configuration (cable interface only) Command Line Usage show cable ucd-interval 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 CMTS Commands modulation-profile physical layer profile characteristics max-calls the maximum number of voice calls configured for this upstream channel Spectrum Group displays the associated Spectrum Group name modem ranging delay the maximum ranging timing offset for a modem that is co-located with (next to) the CMTS, in microseconds.The range, 0 to 600 (with a default of 250), corresponds to ranging timing offsets in REFCLK units of 0 to 6144 (with a default of 2560).
BSR 2000 Command Reference Guide Release 1.0 Group Access All Command Mode Interface Configuration (cable interface only) Command Line Usage show cable upstream { | } Command Syntax 11-242 NUM the upstream channel number X/Y X is 0. Y is the CMTS port number. MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands show docsis-version The show docsis-version command displays the DOCSIS version of a slot in the BSR 2000 chassis. Returned values are DOCSIS 1.X (DOCSIS 1.0 or DOCSIS 1.1) and DOCSIS 2.0. Group Access All Command Mode All modes except User EXEC Command Line Usage show docsis-version <0-0> Command Syntax 0-0 526363-001-00 Rev. B This number is always 0 for the BSR 2000.
BSR 2000 Command Reference Guide Release 1.0 show docstest The show docstest command displays DOCSIS 2.0 testing information. A displayed value of "0" indicates that no test has been initiated. Note: DOCSIS 2.0 test mode must be enabled with the docstest enable command before DOCSIS 2.0 testing information can be displayed. Group Access MSO Command Mode Privileged EXEC Command Line Usage show docstest 11-244 MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide 11-246 Release 1.
Release 1.0 CMTS Commands bandwidth requiring the QoS for that modem. Each time the modem connects to an upstream channel, the value for the guaranteed upstream value increments by the QoS rate.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax 11-248 X/Y X is 0. Y is the CMTS port number | turns on output modifiers (filters) begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax 11-250 X/Y X is 0.
Release 1.0 CMTS Commands show interfaces cable intercept Use the show interfaces cable intercept command to view statistical information for each intercepted Customer Premises Equipment (CPE) MAC address. The show interfaces cable intercept command displays the following CPE information: MAC Address MAC (hardware) address of a CPE, such as a customer’s PC or VoIP phone. Destination IP Address IP address of the data collection server.
BSR 2000 Command Reference Guide Release 1.0 show interfaces cable service-class The show interfaces cable service-class command displays interface level service class information for all downstream and upstream service classes, downstream service classes, or upstream service classes.
Release 1.0 CMTS Commands Command Line Usage show interfaces cable service-class [all | downstream | upstream] [ | {begin | exclude | include} {} [ | {count | count-only}]] show interfaces cable service-class [all | downstream | upstream] [ | {count | count-only}] Command Syntax X/Y X is 0. Y is the CMTS port number.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide 11-256 Release 1.0 | turns on output modifiers (filters) begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 discarded number of packets discarded total active modems total active cable modems on this downstream channel Spectrum Group the associated upstream Spectrum Group names Group Access All Command Mode All modes except User EXEC Command Line Usage show stats cmts [ | {begin | exclude | include} {} [ | {count | count-only}]] show stats cmts [ | {count | count-only}] Command Syntax 11-258 NUM This number is always 0 for the BSR 2000.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 The following is an example of typical screen output from the show stats summary error command: MAC Address I/F 000b.0643.36c8 000b.0643.3716 000b.0643.375a 000b.0643.3766 000b.0643.3ac6 000b.0643.3b60 000b.0643.3b72 000b.0643.3b78 000b.0643.3b84 000b.0643.3b90 000b.0643.3b9a 000b.0643.3bb2 000b.063b.b320 000b.0643.33fc 000b.0643.361a 000b.0643.3718 000b.0643.3bb0 0020.4027.a15c 0020.409a.24f0 0020.409a.
Release 1.0 CMTS Commands snr display The snr display command displays SNR measurement data to a console or telnet session. SNR measurement data is retrieved either from an operational CMTS module or a file system. Group Access MSO Command Mode Privileged EXEC Command Line Usage snr display {{}} | flash: | loop-data {{}} | nvram: } Command Syntax NUM This number is always 0 for the BSR 2000.
BSR 2000 Command Reference Guide Release 1.0 snr loop The snr loop command allows an operator to perform SNR measurements for a specified number of times on one particular frequency.
Release 1.0 CMTS Commands mac the MAC address, in the form of xxxx.xxxx.xxxx, of a device to perform SNR measurements on equalization off - perform SNR measurements without equalization on - eperform SNR measurements with equalization ingress-cancel off - perform SNR measurements without ingress cancellation on - perform SNR measurements with ingress cancellation modulation-type 16qam - perform SNR measurements for 16qam mode qpsk - perform SNR measurements for QPSK mode 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snr setup The snr setup command is used to configure SNR measurement on the BCM3138/ BCM3140 chip set.
Release 1.0 CMTS Commands 5000000-55000000 is the J-DOCSIS standard start frequency in Hz 5000000-55000000 is the J-DOCSIS standard end frequency in Hz.
BSR 2000 Command Reference Guide Release 1.0 snr setup-get The snr setup-get command dispalys the current SNR measurement feature configuration. Group Access MSO Command Mode Privileged EXEC Command Line Usage snr setup-get [ []] Command Syntax 11-266 NUM This number is always 0 for the BSR 2000. NUM valid upstream port number MGBI 526363-001-00 Rev.
Release 1.0 CMTS Commands snr start The snr start command initiates SNR measurement via the RF Sentry Group Access MSO Command Mode Privileged EXEC Command Line Usage snr start {{}} [] Command Syntax NUM This number is always 0 for the BSR 2000. NUM valid upstream port number mac MAC address of the reference modem in the form of xxxx.xxxx.xxxx 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 snr store The snr store command saves the latest SNR measurement data for a 2x8 CMTS module to a file system. The user specifies a particular slot and port, the file system (NVRAM or Flash), and a file name without any extension to be used to store the SNR measurement data. An extension of ".snr" will be automatically added to the file name.
Release 1.0 CMTS Commands spreader on The spreader on command enables or disables the spreader for this S-SDMA channel. Group Access MSO Command Mode Modulation Profile Configuration Command Line Usage spreader on no spreader on 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 tcm-encoding on The tcm encoding on command enables trellis-coded modulation (TCM) for this S-CDMA channel. The trellis-coded modulation technique partitions the constellation into subsets called cosets so as to maximize the minimum distance between pairs of points in each coset. The no tcm encoding on command disables trellis-coded modulation (TCM) for this S-CDMA channel.
Release 1.0 CMTS Commands time band The time band command is used to schedule when a spectrum group band is available. The spectrum group band can be made available on either a daily or weekly schedule. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage time { | } band <5000000-42000000> <5000000-42000000> no time { | } band <5000000-42000000> <5000000-42000000> Command Syntax day The three letter abbreviation for day of the week.
BSR 2000 Command Reference Guide Release 1.0 time delete The time delete command can be used to schedule the time when the spectrum group band is removed on a daily or weekly basis. Group Access MSO Command Mode Cable Spectrum Group Command Line Usage time { } delete <5000000-42000000> <5000000-42000000> no time { } delete <5000000-42000000> <5000000-42000000> Command Syntax 11-272 day The three letter abbreviation for day of the week.
12 BGP Commands Introduction This chapter describes the Border Gateway Protocol version 4 (BGP-4) commands used with the BSR. BGP is an Inter-Autonomous System (AS) routing protocol that exchanges network availability information with any other router speaking BGP. The information for a network is the complete list of ASs that traffic must transport to reach that network and is then used to assure loop-free paths.
BSR 2000 Command Reference Guide Release 1.0 aggregate-address The aggregate-address command creates an entry in the BGP routing table. The no aggregate-address command disables this function. Use the aggregate-address command to implement aggregate routing by redistributing the route in BGP. Group Access ISP Command Mode Router Configuration Command Line Usage aggregate-address
Release 1.0 BGP Commands auto-summary The auto-summary command returns the user back to the automatic summarization default of subnet routes into network-level routes. The no auto-summary command disables this function. When the route is summed up, it reduces the amount of routing information in the routing tables. Use the network command or the no auto-summary command to advertise and transmit subnet routes in BGP. BGP will not accept subnets distributed from IGP.
BSR 2000 Command Reference Guide Release 1.0 bgp always-compare-med The bgp always-compare-med command enables comparison of the Multi-exit Discriminator (MED) from path entries from different ASs. The no bgp always-compare-med command stops comparisons. Use the bgp always-compare MED command to change the default, allowing comparison of MEDs, which are received from any autonomous system.
Release 1.0 BGP Commands bgp confederation identifier The bgp confederation identifier command configures a BGP confederation identifier. The no bgp confederation identifier command removes a BGP confederation identifier. Use the bgp confederation identifier command to reduce the IBGP mesh which splits an autonomous system into many autonomous systems. They are then grouped into an individual confederation.
BSR 2000 Command Reference Guide Release 1.0 bgp confederation peers The bgp confederation peers command configures the ASs that belong to the confederation. The no bgp confederation peer command removes an AS from the confederation. Use the bgp confederation peers command to configure the ASs that belong to a confederation. Autonomous systems specified in this command are visible internally to a confederation. Each autonomous system is fully meshed within itself.
Release 1.0 BGP Commands bgp dampening The bgp dampening command enables BGP route dampening. The no bgp dampening command to sets the default values or disables this function. Note: The penalty is halved after the half-life period when a route is flapping. The router configured for damping (dampening) assigns a penalty to a route when a route flaps. Penalties are cumulative and are stored in the BGP routing table. A flapping route is suppressed when its penalty exceeds the suppress limit.
BSR 2000 Command Reference Guide Release 1.0 Command Default half life = 15 minutes route reuse = 750 route suppression = 2000 maximum suppression = 4 times the half-life time 12-8 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands bgp default local-preference The bgp default local-preference command changes the default local preference value which is sent to all routers in the local ASs. The no bgp default local-preference command configures a default local preference value. Group Access ISP Command Mode Router Configuration Command Line Usage bgp default local-preference <0-4294967295> no bgp default local-preference <0-4294967295> Command Syntax 0-4294967295 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 bgp permit The bgp permit command permits updates with either the AGGREGATOR attribute set to the 0 Autonomous System (AS) or with the 0.0.0.0 address in the BGP routing process. The no bgp permit command disables the updates.
Release 1.0 BGP Commands bgp router-id The bgp router-id command overrides a configured BGP router identifier (IP address) by manually configuring a new identifier. The no bgp router-id command restores the initial configuration. Group Access ISP Command Mode Router Configuration Command Line Usage bgp router-id no bgp router-id Command Syntax A.B.C.D 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear ip bgp The clear ip bgp command resets a BGP connection using soft reconfiguration. Group Access ISP Command Mode All Modes except User EXEC Command Line Usage clear ip bgp {* | | }[soft [in | out]] Command Syntax * resets active BGP sessions A.B.C.
Release 1.0 BGP Commands clear ip bgp dampening The clear ip bgp dampening command clears route dampening information and unsuppress the suppressed routes. Group Access ISP Command Mode All Modes except User EXEC Command Line Usage clear ip bgp dampening [ | ] Command Syntax A.B.C.D IP address of the network about which to clear dampening information A.B.C.D network mask applied to the above address 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear ip bgp flap-statistics The clear ip bgp flap-statistics clears BGP flap statistics. Group Access ISP Command Mode All Modes except User EXEC Command Line Usage clear ip bgp flap-statistics [ | filter-list <1-199> | regexp ] Command Syntax 12-14 A.B.C.
Release 1.0 BGP Commands default-information originate The default-information originate command generates a default route into the BGP database. The no default-information originate command disables default route generation. Group Access ISP Command Mode Router Configuration Command Line Usage default-information originate no default-information originate Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 default-metric The default metric feature is used to eliminate the need for separate metric definitions for each routing protocol redistribution.The default-metric command forces the BGP routing protocol to use the same metric value for all distributed routes from other routing protocols. The no default-metric command removes or changes the default metric value for the BGP routing protocol.
Release 1.0 BGP Commands distance bgp The distance bgp command sets external, internal, and local administrative distances for routes to function. The no distance bgp command sets the default values. Use the distance bgp command to administer distance based on the preferred routing information source received from a router or group of routers. This enables the system to prioritize protocols dependant upon the distances between 1 to 255, where 0 is the best route, and the most unreliable route is 255.
BSR 2000 Command Reference Guide Release 1.0 Command Default 12-18 external distance = 20 internal distance = 200 local distance = 200 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands distribute-list in The distribute-list in command filters networks received in routing updates. The no distribute-list in command changes or cancels the filters received in updates.
BSR 2000 Command Reference Guide Release 1.0 distribute-list out The distribute-list out command prevents networks from being advertised in updates. The no distribute-list out command enables update advertisements. Use the distribute-list out command to apply the access list to outgoing route updates.
Release 1.0 BGP Commands ip as-path access-list The ip as-path access-list command creates or modifies a BGP related access list and its elements. The no ip as-path access command deletes the corresponding list element. Use the no ip as-path access-list command to modify elements and add to the IP as-path access list of corresponding elements. Use the ip as-path access-list and the neighbor filter-list commands to use as-path filters to filter BGP advertisements.
BSR 2000 Command Reference Guide Release 1.0 ip community-list The ip community-list command creates a BGP related access list and its elements.There are two types of community lists: standard and extended. The standard community lists have a list number from 1 to 99. The extended community lists have a list number from 100 to 199. The ip community-list deletes the community lists and all associated elements.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 match as-path The match as-path command matches a BGP autonomous system path access list match entries or appends new list numbers to the existing match entry. The no match as-path command removes the list numbers from the match entry used in the command. Use the match as-path command to match a BGP autonomous system path to advertise on the route-map. Values can be set using the match as-path command.
Release 1.0 BGP Commands match community The match community command creates a BGP autonomous system community access list match entry or appends new list numbers to the existing match entry. The no match community command removes the match entry completely. The no match community command removes the list numbers or the exact-match attribute from the match entry use the command Use the match community-list command to ensure that the route is advertised for outbound and inbound route-maps.
BSR 2000 Command Reference Guide Release 1.0 maximum-paths The maximum-paths command specifies the maximum number of parallel routes an IP routing protocol can support. The no maximum-paths command changes or cancels the number of maximum paths. Group Access RESTRICTED Command Mode Router Configuration Command Line Usage maximum-paths <1-2> no maximum-paths Command Syntax 1-2 12-26 the maximum number of parallel routes MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor advertisement-interval The neighbor advertisement-interval command sets the minimum amount of time between sending BGP routing updates. Use the no neighbor advertisement-interval form of this command to delete an entry. Use the neighbor advertisement-interval command to configure all the members of the peer group with the same attributes. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor {
BSR 2000 Command Reference Guide Release 1.0 neighbor confed-segment The neighbor confed-segment command allows you configure a neighbor to use either AS confederation sequence or AS confederation set as the path segment type in the AS path attribute. The no neighbor confed-segment command disables the AS confederation path segment type attribute. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor {} confed-segment {sequence | set} no neighbor {
Release 1.0 BGP Commands neighbor default-originate The neighbor default-originate command allows a BGP speaker to send the default route 0.0.0.0 to a neighbor for the neighbor’s default. The no neighbor default-originate command sends no route as a default. The neighbor default-originate command does not require the presence of 0.0.0.0 in the local router, and when used with a route map, the default route 0.0.0.
BSR 2000 Command Reference Guide Release 1.0 neighbor description The neighbor description command provides a neighbor a description. The no neighbor description clears the provided neighbor description. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor { | } description [LINE] no neighbor { | } description [LINE] Command Syntax 12-30 A.B.C.
Release 1.0 BGP Commands neighbor distribute-list The neighbor distribute-list command distributes BGP neighbor information based on the access list. The no neighbor distribute-list command deletes an entry. Use the neighbor distribute-list command to filter BGP advertisements. Also, use the ip as-path access-list and the neighbor filter-list commands to use as-path filters to filter BGP advertisements. If a BGP peer group is specified, all members of that group are associated.
BSR 2000 Command Reference Guide Release 1.0 neighbor ebgp-multihop The neighbor ebgp-mulithop command accepts route updates from external peers residing on the network that are not directly connected. The no neighbor ebgp-mulithop command blocks route updates. Use the neighbor ebgp-multihop command to modify BGP peer groups for unified configuration by specifying a peer-group-name. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor {
Release 1.0 BGP Commands neighbor filter-list The neighbor filter-list command creates a BGP filter. The no neighbor filter-list command disables this function. Use the neighbor filter-list command to create filters on both inbound and outbound BGP routes. Unlimited weight filters are accepted on a per-neighbor principle, but only one inbound or one outbound filter is accepted, not both. Route selection rules determine the weight of a route.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax A.B.C.D neighbor IP address WORD BGP peer group 1-199 filter list number in access list to incoming routes out access list to outgoing routes weight 0-65535 BGP weight metric assigned for competing incoming routes; accepted values are 0 to 65535; the largest weight is preferred Command Default Disabled 12-34 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor maximum-prefix The neighbor maximum-prefix command controls the number of prefixes accepted from a neighbor. The no neighbor maximum-prefix command stops the controlled number of prefixes accepted from a neighbor. Use the neighbor maximum-prefix command to manage the number of prefixes accepted from a neighbor. Note: A prefix is a classless route or a route with a particular starting point and length, with unlimited prefixes. Therefore, 198.7.97.0/27 and 198.7.97.
BSR 2000 Command Reference Guide Release 1.0 1-100 integer specifying what percentage of the maximum number that the router generates a warning message warning-only only generate a warning message when the maximum number is exceeded Command Default Disabled Threshold default, 75% 12-36 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor next-hop-self The neighbor next-hop-self command disables BGP processing updates. The no neighbor next-hop-self command enables BGP processing updates. Note: Members of a peer group realize configured specifics when the peer-group-name argument is used with the neighbor next-hop-self command. Specifying the command with an IP address will override the value inherited from the peer group. Use the set ip next-hop command for additional control.
BSR 2000 Command Reference Guide Release 1.0 neighbor password The neighbor password command enables the Message Digest 5 (MD5) authentication on a TCP connection between two BGP peers. The no neighbor password command disables the Message Digest 5 (MD5) authentication on a TCP connection between two BGP peers. Use the neighbor password command to authenticate and to verify TCP connections between two BGP peers, of which the same password is configured.
Release 1.0 BGP Commands neighbor peer-group (assigning members) The neighbor peer-group (assigning members) command configures a BGP neighbor to be a member a BGP peer group. The no neighbor peer-group (assigning members) command removes the neighbor from the peer group. The neighbor peer-group creates a new member of a peer-group. If there is no such peer, it will be created and assigned to the group.
BSR 2000 Command Reference Guide Release 1.0 neighbor peer-group (creating) The neighbor peer-group (creating) command creates a BGP peer group. The no neighbor peer-group (creating) command removes the peer group and all of its members. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor peer-group no neighbor peer-group Command Syntax WORD 12-40 peer group name MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor remote-as The neighbor remote-as command performs many functions as described below. Use the neighbor remote-as number command to assign a BGP router to an autonomous system. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor remote-as <1-65535> creates a new BGP peer and assigns an AS number to it. If such peer does not exist already, it assigns a new AS number to existing peer.
BSR 2000 Command Reference Guide Release 1.0 Command Syntax 12-42 A.B.C.D BGP peer address WORD name of BGP peer group 1-65535 neighbor autonomous system number MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor remove-private-as The neighbor remove-private-as command triggers the removal of private AS numbers from outbound updates. Use no neighbor remove-private-as command to stops such removal. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor { | } remove-private-as no neighbor { | } remove-private-as Command Syntax A.B.C.
BSR 2000 Command Reference Guide Release 1.0 neighbor route-map The neighbor route-map command applies a route map to incoming or outgoing routes. The no neighbor route-map command clears a route map for incoming and outgoing routes. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor { | } route-map {in | out} no neighbor { | } route-map {in | out} Command Syntax 12-44 A.B.C.
Release 1.0 BGP Commands neighbor route-reflector-client The neighbor route-reflector-client command configures the router as a BGP route-reflector. The no neighbor route-reflector-client command configures a router back to a BGP route-reflector. Use the neighbor route-reflector-client command to establish a local router to act as the route-reflector with the specified neighbor as a client. Note: When all clients are disabled, the local router is no longer a route-reflector.
BSR 2000 Command Reference Guide Release 1.0 neighbor send-community The neighbor send-community command will allow a communities attribute, if any, to be sent in outbound updates to a neighbor. The no neighbor send-community command stops sending communities attribute. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor { | } send-community [both | extended | standard] no neighbor {
Release 1.0 BGP Commands neighbor shutdown The neighbor shutdown command disables a neighbor or peer group. The no neighbor shutdown command enables a neighbor or peer group. Use the neighbor shutdown command to end an session for a particular neighbor or peer group. This removes all routing information associated. Use the show ip bgp summary command for a list of neighbors and peer-group connection.
BSR 2000 Command Reference Guide Release 1.0 neighbor soft-reconfiguration inbound The neighbor soft-reconfiguration inbound command starts the storage of incoming updates without any modification. The no neighbor soft-reconfiguration inbound command stops this storage and releases the memory used for them. Use the neighbor soft-reconfiguration inbound command to start update story required to enable inbound software configuration with the clear ip bgp soft [in] command.
Release 1.0 BGP Commands neighbor timers The neighbor timers command sets the timers for a particular BGP peer or peer group. The no neighbor timers command clears the timers for a particular BGP peer or peer group. Use the neighbor timers command to configure a specific neighbor or peer-group timers values to bypass the timers configured for all BGP neighbors using the timers bgp command.
BSR 2000 Command Reference Guide Release 1.0 Command Default keepalive = 60 seconds hold time = 180 seconds 12-50 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands neighbor update-source loopback The neighbor update-source loopback command allows an internal BGP session to use any loopback interface for the TCP session. The no neighbor update-source loopback command blocks a BGP session from using a loopback interface for the TCP session. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor { | } update-source loopback <1-64> no neighbor {
BSR 2000 Command Reference Guide Release 1.0 neighbor weight The neighbor weight command establishes a weight to a neighbor connection. The no neighbor weight command removes a weight to a neighbor connection. Note: Initially, all routes learned from this neighbor will have the assigned weight. The route with the highest weight is chosen as the choice route when multiple routes are available on the network. Group Access ISP Command Mode Router Configuration Command Line Usage neighbor {
Release 1.0 BGP Commands network The network command specifies the list of networks for the BGP routing process. The no network command deletes the entry. Use the network command to control what networks are originated. be included in the BGP updates. Network types are learned from connected routes, dynamic routing, and static route sources. Because BGP can handle subnetting and supernetting, the mask is used. The maximum number of network commands is based on the configured nvram or ram.
BSR 2000 Command Reference Guide Release 1.0 redistribute The redistribute command redistributes routes from one protocol domain to another routing domain. The no redistribute command disables route distribution from one protocol domain to another routing domain.
Release 1.0 BGP Commands external 2 routes that are external to an autonomous system, but are imported into OSPF as Type 2 external route rip RIP source protocol static IP or BGP static routes metric 0-4294967295 metric value used for the redistributed route. route-map WORD the name of the route-map used to conditionally control the route redistribution weight 0-65535 set a network weight value when redistributing into BGP Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 route-map The route-map command creates or modifies route-maps and their sequences. The no route-map command removes the corresponding sequence from the route-map.If there are no sequences left in the route-map, the route-map will be deleted too. Use the route-map command, and the match and set commands to configure the rules for redistributing routes from one routing protocol to another.
Release 1.0 BGP Commands Command Syntax WORD route-map name 0-65535 route-map sequence number deny denies access for matching conditions permit permits access for matching conditions 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 router bgp The router bgp command configures the BGP routing process. Use the no router bgp command clears BGP routing process configuration. Use the router bgp command to establish a distributed routing core that automatically guarantees the loop-free exchange of routing information between AS’s.
Release 1.0 BGP Commands set as-path prepend The set as-path prepend command modifies AS system path attributes for the matched BGP routes. The no set as-path prepend command ends modification of a system path for BGP routes. Use the set as-path prepend command to guide the path information to control the BGP decision process.
BSR 2000 Command Reference Guide Release 1.0 set comm-list The set comm-list command deletes communities from the community attribute of an inbound or outbound update. The no set comm-list command deletes the entry. Use the set comm-list command to delete communities from the community attribute of inbound or outbound updates using a route map to filter and determine the communities to be deleted.
Release 1.0 BGP Commands Command Syntax 1-99 standard community list number 100-199 extended community list number delete delete inbound or outbound communities from the community attribute 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set community The set community command add or replace communities from the community attribute of an inbound or outbound update. Use the no set community command removes the specified communities from the set. Use the route-map command, and the match and set commands to configure the rules for redistributing routes from one routing protocol to another. Each route-map command has a list of match and set commands associated with it.
Release 1.0 BGP Commands Command Syntax 1-4294967295 community number additive add to the existing community local-AS do not advertise this route to peers outside of the local autonomous system no-advertise do not advertise this route to any peer internal or external no-export routes with this community are sent to peers in other sub-autonomous systems within a confederation none no community attribute 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 set ip next-hop The set ip next-hop command establishes a next-hop value for the AS path. The no ip next-hop command deletes the entry. Use the ip policy route-map interface configuration command, the route-map global configuration command, and the match and set route-map configuration commands, to define the conditions for policy routing packets. The ip policy route-map command identifies a route map by name.
Release 1.0 BGP Commands set local-preference The set-local preference command establishes a preference value for the AS system path. Use the set local-preference command to send the local-preference to all routers in the local autonomous system. Use the no set-local preference form of this command to delete the entry. Note: In the no set-local preference command, the optional <0-4294967295> argument has no effect.
BSR 2000 Command Reference Guide Release 1.0 set metric-type The set metric-type command sets the destination routing protocol. The no set metric-type command returns the default. Use the set metric-type command, and the match and set commands to configure the rules for redistributing routes from one routing protocol to another. Each set metric-type command has a list of match and set commands associated with it.
Release 1.0 BGP Commands set origin The set origin command configures the conditions for redistributing routes from any protocol to any protocol. The no set origin command deletes the BGP origin code. When the set origin command configures redistributing routes from any protocol to any protocol, any match clause is necessary which includes pointing to a “permit everything” to set tags.
BSR 2000 Command Reference Guide Release 1.0 set tag The set tag command sets the value of the destination routing protocol. The no set tag command removes the value. The route-map global configuration command and the match and set route-map configuration commands are used together to define the conditions for redistributing routes from one routing protocol into another. Each route-map command has a list of match and set commands associated with it.
Release 1.0 BGP Commands set weight The set-weight command to set the route weight on the network. The first autonomous system match determines the weight to be set. Use the set weight command to set the route weight on the network. The first AS match determines the weight to be set. The route with the highest weight is chosen as the choice route when multiple routes are available on the network. Weights spoken when an as path is matched, override any weight set by the neighbor command.
BSR 2000 Command Reference Guide Release 1.0 show ip as-path-access-list The show ip as-path-access-list command displays configured AS path access lists and their elements. Use the show ip as-path-access-list command to display configured as-path access lists and their elements. With the optional access list number argument, it displays the specified as-path access list, if such list exists. Without it, it displays all configured as-path access lists.
Release 1.0 BGP Commands show ip bgp The show ip bgp command displays entries in the routing table. Use the show ip bgp command to determine whether the session is active or not. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip bgp [] [] [longer-prefixes] [ | {begin | exclude | include} {} [ | {count | count-only}]] show ip bgp [] [] [longer-prefixes] [ | {count | count-only}] Command Syntax A.B.C.
BSR 2000 Command Reference Guide 12-72 Release 1.0 count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands show ip bgp cidr-only The show ip bgp cidr-only command displays routes without natural network masks, or Classless Inter-domain Routing (CIDR) routes.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp community The show ip bgp community command display routes that belong to specified BGP communities.
Release 1.0 BGP Commands begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp community-list The show ip bgp community-list command display routes that are permitted by the BGP community list.
Release 1.0 BGP Commands show ip bgp dampened-paths The show ip bgp dampened-paths command displays BGP dampened routes.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp flap-statistics The show ip bgp flap-statistics command displays BGP flap statistics. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip bgp flap-statistics [] [] [longer-prefixes ] [filter-list <1-199> ] [ regexp ] [ | {begin | exclude | include} {} [ | {count | count-only}]] show ip bgp flap-statistics [] [
Release 1.0 BGP Commands include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp memory The show ip bgp memory command displays BGP memory usage information.
Release 1.0 BGP Commands show ip bgp neighbors The show ip bgp neighbors command displays information about TCP and BGP connections to neighbors.
BSR 2000 Command Reference Guide 12-82 Release 1.0 begin filter for output that begins with the specified string exclude filter for output that excludes the specified string include filter for output that includes the specified string WORD the specified string count count the number of outputted lines count-only count the number of lines while suppressing screen output MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands show ip bgp paths The show ip bgp paths command displays all BGP paths in the database.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp peer-group The show ip bgp peer-group command displays information about BGP peer groups.
Release 1.0 BGP Commands show ip bgp regexp The show ip bgp regexp command displays routes matching the regular expression.
BSR 2000 Command Reference Guide Release 1.0 show ip bgp summary The show ip bgp summary command displays the status of all BGP connections.
Release 1.0 BGP Commands show ip community-list The show ip community-list command displays a configured community access list and the associated elements. Use the show ip community access list command to display configured community access lists and their elements. With the optional access list number argument, it displays the specified community access list, if such list exists. Without it, it displays, all configured community access lists.
BSR 2000 Command Reference Guide Release 1.0 synchronization The synchronization command enables IGP synchronization. The no synchronization command disables IGP synchronization. Group Access ISP Command Mode Router Configuration Command Line Usage synchronization no synchronization 12-88 MGBI 526363-001-00 Rev.
Release 1.0 BGP Commands timers bgp The timers bgp command adjusts BGP network timers. The no timers bgp command resets the BGP timing defaults values.
13 PIM Commands Introduction This chapter describes the Protocol-Independent Multicast (PIM) commands that are supported on the BSR 2000. The BSR supports PIM in sparse mode. PIM Command Descriptions This section contains an alphabetized list and descriptions of the PIM commands supported by the BSR. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ip pim border Use the ip pim border command to configure a PIM domain boundary on the interface of a border router peering with one or more neighbors outside the PIM domain. Group Access ISP Command Mode Interface Configuration Command Line Usage ip pim border no ip pim border 13-2 MGBI 526363-001-00 Rev.
Release 1.0 PIM Commands ip pim dr-priority The ip pim dr-priority command sets the priority by which a router is elected as the designated router (DR). When a Designated Router (DR) is an election candidate, the router with the highest priority is elected as the DR. The DR priority is configured on the router’s interface. If a DR priority is assigned on multiple router interfaces, then the router with the highest IP address is used as the DR.
BSR 2000 Command Reference Guide Release 1.0 ip pim message-interval Use the ip pim message-interval command to specify the PIM router join/prune messages interval. The no ip pim message-interval command sets the join/prune message interval to the default value.
Release 1.0 PIM Commands ip pim query-interval The ip pim query-interval command adjusts how often PIM router query messages are sent to other PIM routers to control the DR process. IP multicast routers send PIM query "Hello" messages to determine which router is the Designated Router (DR) for each LAN segment (subnetwork). The DR sends Internet Group Management Protocol (IGMP) host query messages to all hosts on the directly connected LAN.
BSR 2000 Command Reference Guide Release 1.0 ip pim spt-threshold lasthop The ip pim spt-threshold lasthop command configures when a PIM leaf router should join the shortest path source tree. This is determined by specifying a network traffic threshold at which the router switches to the shortest path source tree after the last hop. The no ip pim spt-threshold lasthop command restores the default value or changes the setting.
Release 1.0 PIM Commands network The PIM version of the network command enables IP networks for the PIM routing process. The no network command disables networks for the PIM routing process. Group Access ISP Command Mode Router Configuration Command Line Usage network no network Command Syntax prefix IP address of directly connected network A.B.C.D PIM wild card bits 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 pim accept-rp The pim accept-rp command configures a router to accept only Join or Prune messages destined for a specified rendezvous point (RP) and for a specific list of groups. The no pim accept-rp command disables accepting only Join or Prune messages so that all Join and Prune messages are processed. The group address must be in the range specified by the access list. If no access list is provided, the default is all class D group addresses.
Release 1.0 PIM Commands pim register-checksum Use the pim register-checksum command to register a packet checksum type. Group Access ISP Command Mode Router Configuration Command Line Usage pim register-checksum [ new | old ] Command Syntax new use only IP and PIM Control Headers old use complete IP packet length Command Default Complete IP packet length 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 pim rp-address The pim rp-address command configures the address of a static PIM rendezvous point (RP) for a particular group. The no pim rp-address command removes an RP address for a particular group. Note: You must configure the IP address of RPs on all routers (including the RP router) if you use static RP. First-hop routers send register packets to the RP address on behalf of source multicast hosts.
Release 1.0 PIM Commands Command Syntax A.B.C.D The IP address of the router to be a statically configured PIM RP. This is a unicast IP address in four-part, dotted notation. 1-99 The number of an access list that defines for which multicast groups the RP should use. This is a standard IP access list. If no number is entered, then the default is the whole class D group range. Command Default No PIM rendezvous points are preconfigured. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 pim unicast-route-lookup The pim unicast-route-lookup command retrieves routes from the BSR’s unicast routing table. Group Access ISP Command Mode Router Configuration Command Line Usage pim unicast-route-lookup no pim unicast-route-lookup 13-12 MGBI 526363-001-00 Rev.
Release 1.0 PIM Commands router pim Use the router pim command to enter Router Configuration mode from Global Configuration mode and enable PIM routing. Group Access ISP Command Mode Global Configuration Command Line Usage router pim 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show ip pim The show ip pim command displays various PIM routing information. Use the show ip pim command to determine whether the session is active or not. Group Access All Command Mode All modes except User EXEC Command Line Usage show ip pim bsr-router show ip pim interface [cable | count | ethernet | gigaether | loopback <1-64>] show ip pim neighbor [
Release 1.0 PIM Commands detail Shows all joins/prunes towards this neighbor rp PIM Rendezvous Point (RP) information A.B.C.
14 Service Class Commands Introduction Service levels provide a means of defining service flows with specific QoS parameters (such as maximum, minimum, or reserved traffic rates, priority, and service scheduling types) and binding them to a named service class. The concept of maximum assigned bandwidth, in the context of a service class, provides a means for controlling the amount of bandwidth that a particular service class can use on an interface.
BSR 2000 Command Reference Guide Release 1.0 Entering Service Class Configuration Mode Service Class Configuration mode provides access to the service class commands described in this section. To enter Service Class Configuration mode, do the following: 1. From Global Configuration mode, enter cable service-class and press the key: MOT(config)# cable service-class The command line prompt changes to: MOT(config-srvclass)# To return to Global Configuration mode: 2.
Release 1.0 Service Class Commands activity-timeout The activity-timeout command specifies the timeout for active QoS parameters which is the maximum duration that resources may remain unused on an active service flow. The no activity-timeout command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 admission-timeout The admission-timeout command specifies the timeout for admitted QoS parameters which is the duration that the CMTS must hold resources for a service flow's admitted QoS parameter set while they are in excess of its active QoS parameter set. The no admission-timeout command a restores the default value.
Release 1.0 Service Class Commands admitted-bw-threshold The admitted-bw-threshold command specifies the amount of admitted bandwidth, in percentage, for a service class on an interface. If this bandwidth threshold is exceeded, an event will be generated. The no admitted-bw-threshold command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 allow-share The allow-share command provides the ability to share bandwidth between different service level classes. Enabling bandwidth sharing, allows the bandwidth of a service level class to be used as a bandwidth “pool” that can be shared by multiple service level classes.
Release 1.0 Service Class Commands cable service-class The cable service-class command enters Service Class Configuration mode from Global Configuration mode. To return to Global Configuration mode, use the end command. Group Access All Command Mode Global Configuration Command Line Usage cable service-class 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cap The cap command specifies the configured active percent (CAP) parameter for a service flow. This parameter controls overbooking for a service class. The no cap command restores the default value. The configured active percent of a service class is an estimation of what fraction, expressed as a percentage, of service flows belonging to that service class that will be simultaneously active on an interface.
Release 1.0 Service Class Commands clear cable srvclass-stats The clear cable srvclass-stats command clears service class statistics on the BSR. These are the same service class statistics displayed with the show cable srvclass-stats command. Group Access All Command Mode Service Class Configuration Command Line Usage clear cable srvclass-stats [<0-0> <0-3> [DOWN | UP | ]] Command Syntax 0-0 This number is always 0 for the BSR 2000.
BSR 2000 Command Reference Guide Release 1.0 enforce-cmts-qos The enforce-cmts-qos command enforces all service level parameters for all cable modems belonging to a service class regardless of the parameters specified in the cable modem’s configuration file. When MAB, CAP, and the maximum or minimum reserve rates are configured for a given service class, these parameters are overriden by a cable modem’s configuration file if the cable modem was configured after the service class was set up.
Release 1.0 Service Class Commands grant-interval The grant-interval command specifies the nominal time between grants. The no grant-interval command restores the default value. Note: Specifying a grant interval is only relevant for service flows using Unsolicited Grant Service (UGS ) or Unsolicited Grant Service with Activity Detection (UGS-AD) scheduling.
BSR 2000 Command Reference Guide Release 1.0 grant-jitter The grant-jitter command specifies the tolerated grant jitter which is the maximum amount of time that the transmission opportunities may be delayed from the nominal periodic schedule for this service flow. The no grant-jitter command restores the default value. Note: Specifying a tolerated grant jitter is only relevant for service flows using Unsolicited Grant Service (UGS ) or Unsolicited Grant Service with Activity Detection (UGS-AD) scheduling.
Release 1.0 Service Class Commands grant-size The grant-size command specifies the unsolicited grant size. Grant size includes the entire MAC frame data PDU from the Frame Control byte to end of the MAC frame. The no grant-size command restores the default value. Note: Specifying an unsolicited grant size is only relevant for service flows using Unsolicited Grant Service (UGS ) or Unsolicited Grant Service with Activity Detection (UGS-AD) scheduling.
BSR 2000 Command Reference Guide Release 1.0 grants-per-interval The grants-per-interval command specifies the number of data grants per grant interval. The no grants-per-interval command restores the default value.
Release 1.0 Service Class Commands mab The mab command specifies the Maximum Assigned Bandwidth (MAB) which is the amount of bandwidth a service class is permitted to use on an interface. It is expressed as a percentage of the total interface bandwidth capacity. The MAB of a service class is applied during admission control to determine whether to admit a new service flow and again by the packet schedulers to provide a class-based weighting to the scheduler. The no mab command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 max-burst The max-burst command specifies the maximum traffic burst size for flows belonging to a specific service class. The no max-burst command restores the default value.
Release 1.0 Service Class Commands max-concat-burst The max-concat-burst command specifies the maximum concatenated burst in bytes which a service flow is allowed. The maximum concatenated burst is calculated from the FC byte of the Concatenation MAC Header to the last CRC in the concatenated MAC frame. The no max-concat-burst command restores the default value. Note: Specifying a maximum concatenated burst is only relevant for upstream service flows.
BSR 2000 Command Reference Guide Release 1.0 max-latency The max-latency command specifies the maximum allowable time for sending a packet from a CMTS network interface to an RF interface starting at the point the packet is received on the network interface. The no max-latency command restores the default value. Note: Specifying a maximum latency value is only relevant for downstream service flows.
Release 1.0 Service Class Commands max-rate The max-rate command specifies the maximum data rate the CM must adhere to and the CMTS must enforce. The no max-rate command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 min-pkt-size The min-pkt-size command specifies the minimum packet size in bytes reserved for a service flow. The minimum reserved rate (min-rate) must be set in conjunction with the minimum packet size for this service flow. The no min-pkt-size command restores the default value.
Release 1.0 Service Class Commands min-rate The min-rate command specifies the minimum reserved traffic rate reserved for this service flow. The minimum packet size (min-pkt-size) must be set in conjunction with the minimum reserved traffic rate for this service flow.The no min-rate command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 name The name command creates a service class record with a user-specified name that is entered on the command line. The no name command deletes this service class record. Commands for specifying configuration parameters will use the service class name as the key word for distinguishing which service class record is being configured.
Release 1.0 Service Class Commands poll-interval The poll-interval command specifies the nominal polling interval between successive unicast request opportunities for this service flow on the upstream channel. The no poll-interval command restores the default value. Note: Specifying a nominal polling interval is only relevant for service flows using Unsolicited Grant Service with Activity Detection (UGS-AD), Real-Time Polling Service (RTPS), or Non-Real-Time Polling Service (NRTPS) scheduling.
BSR 2000 Command Reference Guide Release 1.0 poll-jitter The poll-jitter command specifies the maximum amount of time that the unicast request interval may be delayed from the nominal periodic schedule for this service flow. The no poll-jitter command restores the default value. Note: Specifying a poll jitter value is only relevant for service flows using Unsolicited Grant Service with Activity Detection (UGS-AD) or Real-Time Polling Service (RTPS) scheduling.
Release 1.0 Service Class Commands req-trans-policy The req-trans-policy command specifies: ■ ■ ■ which IUC opportunities the CM uses for upstream transmission requests and packet transmissions for this service flow whether requests for this Service Flow may be piggybacked with data whether data packets transmitted on this service flow can be concatenated, fragmented, or have their payload headers suppressed For UGS, it also specifies how to treat packets that do not fit into the UGS grant.
BSR 2000 Command Reference Guide Release 1.0 Command Default BE-UP = 0 UGS = 0x7f UGS-AD = 0x7f RTPS = 0x1f NRTPS = 0 14-26 MGBI 526363-001-00 Rev.
Release 1.0 Service Class Commands restricted admission disabled The restricted admission disabled command disables the admission of service flows in the admission restricted state. The admission restricted state is when a service flow is admitted when there is insufficient resources to meet its reserved rate and, subsequently, the flow only receives best effort service. The no restricted admission disabled command enables the admission of service flows in the admission restricted state.
BSR 2000 Command Reference Guide Release 1.0 schedpriority The schedpriority command assigns a scheduling priority for a service class. The no schedpriority command a restores the default value. Each service class must be assigned a scheduling priority to determine the order in which service flows are serviced for transmitting packets (downstream) and generating data grants (upstream).
Release 1.0 Service Class Commands show cable service-class The show cable service-class command displays a configuration summary for all service classes, including all default service classes, that are active on the BSR.The complete configuration of an individual service class can also be displayed.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 show cable srvclass-stats The show cable srvclass-stats command displays service class statistics for a specified service class on a specified interface. Group Access All Command Mode All modes except User EXEC Command Line Usage show cable srvclass-stats {<0-0>} {<0-3>} {} Command Syntax 14-32 0-0 This number is always 0 for the BSR 2000.
Release 1.0 Service Class Commands tos-overwrite The tos-overwrite command provides an "AND" and "OR" mask which the CMTS must use to overwrite the "type of service" field on all upstream IP packets on a service flow. If this parameter is omitted, then the TOS field will not be modified by the CMTS. The no tos-overwrite command restores the default value.
BSR 2000 Command Reference Guide Release 1.0 trafpriority The trafpriority command specifies the relative priority of service flows that have identical QoS parameters. The no trafpriority command restores the default value.
15 Secure Shell Server Commands Introduction Secure Shell server (SSH) is a program that allows remote hosts to login to the BSR over a non-secure network and execute commands in a secure manner. SSH provides strong authentication and secure communications over non-secure networks such as the public Internet. The SSH protocol uses TCP as the transport layer. An SSH server listens for connections from SSH clients on a well-known TCP port.
BSR 2000 Command Reference Guide Release 1.0 show ssh config The show ssh config command displays the following configuration information for an SSH session.
Release 1.0 Secure Shell Server Commands subsystemString the type of SSH server Private HostKey file the private hostkey authentication filename Public HostKey file the public hostkey authentication filename Note: To display modifications to the default SSH configuration, use the following command: show running-config | include ssh Group Access All Command Mode All modes except User EXEC Command Line Usage show ssh config Command Default Restricted admission is enabled by default.
BSR 2000 Command Reference Guide Release 1.0 show ssh hostkey-fingerprint The show ssh hostkey-fingerprint command displays the fingerprint of a public key. Note: The SSH server must be disabled to execute this command. Group Access All Command Mode All modes except User EXEC Command Line Usage show ssh hostkey-fingerprint {nvram: } Command Syntax nvram: filename 15-4 display fingerprint of public hostkey file stored in NVRAM MGBI 526363-001-00 Rev.
Release 1.0 Secure Shell Server Commands show users ssh The show users ssh command displays information about active SSH sessions including SSH resource use and active calls. Group Access All Command Mode All modes except User EXEC Command Line Usage show users ssh 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ssh ciphers The ssh ciphers command configures a cipher for the encryption of SSH session data.
Release 1.0 Secure Shell Server Commands twofish192-cbc Twofish in cbc mode with 192-bit keys twofish256-cbc Twofish in cbc mode with 256-bit keys 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ssh enable The ssh enable command enables an SSH process. The no ssh enable command disables the SSH process. If SSH is disabled, all existing SSH sessions will be terminated. Group Access ISP Command Mode Global Configuration Command Line Usage ssh enable no ssh enable 15-8 MGBI 526363-001-00 Rev.
Release 1.0 Secure Shell Server Commands ssh-keygen2 The ssh-keygen2 tool generates authentication key files for the BSR 2000 Secure Shell Server. Host keys are required for the SSH Server and can either be generated in the BSR 2000 or generated on another BSR and copied over. Note: The SSH Server must be disabled on the BSR 2000 before running the ssh-keygen2 tool. Caution: The BSR 2000 Secure Shell Server only accepts host key files generated with the ssh-keygen2 tool.
BSR 2000 Command Reference Guide Release 1.0 passphrase Sets a passphrase for SSH connections. The password can be up to 31 characters maximum. type dsa Digital Signature Algorithm key type type rsa Rivest-Shamir-Adleman public-key algorithm key type Command Default bits = 1024 hostkeyfile = nvram: hostkey type = dsa 15-10 MGBI 526363-001-00 Rev.
Release 1.0 Secure Shell Server Commands ssh load-host-key-files The ssh load-host-key-files command specifies a new private or public hostkey authentication file. The default hostkey authentication file names are “hostkey and hostkey.pub”. These two files must exist and must be valid key files. Use the UNIX ssh-keygen2 tool to generate a new hostkey authentication file. Note: If the hostkey authentication files are invalid, SSH will not run.
BSR 2000 Command Reference Guide Release 1.0 ssh logout session-id The ssh logout session-id command will terminate an SSH session in progress. This command can be used when a user wants to reconnect using new configuration parameters. Group Access System Administrator Command Mode Privileged EXEC Command Line Usage ssh logout session-id <0-3> Command Syntax 0-3 15-12 the session-id number - the session-id is the number displayed with the show users ssh ssh command MGBI 526363-001-00 Rev.
Release 1.0 Secure Shell Server Commands ssh message-authentication The ssh message-authentication command specifies the message authentication (data integrity) algorithm used for SSH sessions.
BSR 2000 Command Reference Guide Release 1.0 ssh password-authentication radius The ssh password-authentication radius command enables RADIUS services to be used for password authentication. The no ssh password-authentication radius command disables this feature.
Release 1.0 Secure Shell Server Commands ssh password-guesses The ssh password-guesses command specifies how many authentication attempts (login and password exchange) will be allowed for an SSH client attempting a connection. Group Access ISP Command Mode Global Configuration Command Line Usage ssh password-guesses <1-5> no ssh password-guesses Command Syntax 1-5 password guess attempt number Command Default 3 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ssh port The ssh port command configures SSH to listen for incoming connections on a defined TCP port number. Group Access ISP Command Mode Global Configuration Command Line Usage ssh port <1-65535> no ssh port Command Syntax 1-65535 port number Command Default 22 15-16 MGBI 526363-001-00 Rev.
Release 1.0 Secure Shell Server Commands ssh session-limit The ssh session-limit command specifies the maximum number of simultaneous SSH sessions that the BSR accepts. Group Access ISP Command Mode Global Configuration Command Line Usage ssh session-limit <0-4> no ssh session-limit Command Syntax 0-4 number of simultaneous SSH sessions Command Default 4 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ssh timeout The ssh timeout command specifies an inactivity timeout value for SSH sessions to time out. Specifying a value of "0" will disable time-out for SSH sessions. Group Access ISP Command Mode Global Configuration Command Line Usage ssh timeout <0-60> Command Syntax 0-60 the timeout value in minutes Command Default 5 minutes 15-18 MGBI 526363-001-00 Rev.
16 PacketCable Commands Overview The BSR fully supports the Cablelabs® PacketCable™ 1.x specification, including VoIP telephony services. Command Descriptions This chapter contains an alphabetized list and descriptions of PacketCable commands used with the BSR. 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable dynamic-service authorization-mode The cable dynamic-service authorization-mode command allows the cable interface to accept dynamic service. The no cable dynamic-service command rejects dynamic service on the cable interface.
Release 1.0 PacketCable Commands Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 cable dynamic-service active-timeout CMs dynamically allocate resources such as service identifiers (SIDs) and bandwidth by using a Dynamic Service Addition (DSA) transaction. If the CM fails to issue a Dynamic Service Deletion Request (DSD-REQ) to the cable interface or the DSD-REQ is being dropped for any reasons (e.g. due to noise), these resources could be held by the cable interface indefinitely.
Release 1.0 PacketCable Commands clear configuration The clear configuration command resets the COPS, Dynamic QoS, event message, or electronic surveillance configuration parameters to the default settings.
BSR 2000 Command Reference Guide Release 1.0 clear cops pdp-ip all The clear cops pdp-ip all command removes all Policy Decision Point (PDP) IP addresses. Group Access All Command Mode PacketCable Configuration Command Line Usage clear cops pdp-ip all 16-6 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands clear counters ipsec The clear counters ipsec command clears the IPSec statistical counters. Group Access All Command Mode All modes except User EXEC Command Line Usage clear counters ipsec 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear packet-cable gate The clear packet-cable gate command releases reserved or committed DQoS and Multimedia gates. Group Access All Command Mode Privileged EXEC Command Line Usage clear packet-cable gate [all | dqos | cops <0-3> | slot | modem | subscriber
Release 1.0 PacketCable Commands clear packet-cable statistics The clear packet-cable statistics command clears event messages, gate, or electronic surveillance statistical counters.
BSR 2000 Command Reference Guide Release 1.0 cmts-ip The cmts-ip command specifies the network or loopback interface IP address used for the PacketCable protocols. Group Access All Command Mode PacketCable Configuration Command Line Usage cmts-ip no cmts-ip Command Syntax A.B.C.D network or loopback interface IP address Command Default Any network or loopback IP address 16-10 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands cops client-timer If the show packet-cable statistics gate command output for the Client-Open Sent field in the COPS Statistics section is incrementing, the network and the PDP server need to be examined to determine the reason for the COPS Client timeouts. The COPS Client Timer (which is the response timer for sending the COPS Client-Open message) can be specified if COPS connections time out before receiving a Client-Accept message.
BSR 2000 Command Reference Guide Release 1.0 cops pdp-ip The cops pdp-ip command restricts COPS connections to a specific Policy Decision Point (PDP). A PDP is either the Call Management Server in the PacketCable architecture or the Policy Server in the PacketCable Multimedia architecture where a Client/MTA policy request is either serviced or rejected. The no cops pdp-ip command removes an IP address from the list.
Release 1.0 PacketCable Commands cops pep-id The cops pep-id command specifies the default Policy Enforcement Point (PEP) text string, that is used in COPS messaging, to uniquely identify the BSR within the PacketCable/PacketCable Multimedia domain The no cops pep-id command restores the default value. Group Access All Command Mode PacketCable Configuration Command Line Usage cops pep-id no cops pep-id Command Syntax string COPS PEP ID string that is between 1 and 32 characters.
BSR 2000 Command Reference Guide Release 1.0 cops status-trap-enable The cops status-trap-enable command enables or disables the COPS status SNMP trap through the DQoSCopsTrap SNMP MIB object.
Release 1.0 PacketCable Commands debug packet-cable gate The debug packet-cable gate command displays DQoS and Multimedia gate state transition information. The no debug packet-cable gate command turns off this debugging function. Group Access All Command Mode Privileged EXEC Command Line Usage debug packet-cable gate no debug packet-cable gate Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug packet-cable trace cops The debug packet-cable trace cops command dumps COPS messages in hexidecimal format to the console. The no debug packet-cable trace cops command turns off this debugging function. Group Access All Command Mode Privileged EXEC Command Line Usage debug packet-cable trace cops no debug packet-cable trace cops Command Default Disabled 16-16 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands debug packet-cable trace em The debug packet-cable trace em command dumps event messages in hexidecimal format to the console. The no debug packet-cable trace em command turns off this debugging function. Group Access All Command Mode Privileged EXEC Command Line Usage debug packet-cable trace em no debug packet-cable trace em Command Default Disabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 debug ipsec The debug ipsec command displays all realtime IP security (IPSec) debugging information to the console. The no debug ipsec command turns off this debugging function. Note: Debugging for IPSec can only occur when IPSec is not shutdown.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 dqos emergency-trap-enable The dqos emergency-trap-enable command enables or disables an SNMP trap for Emergency Calls through the rdnPktDQoSEmergencyTrapEnable SNMP MIB object. If the Emergency Call SNMP trap is enabled, the BSR generates an SNMP trap if an Emergency Call is initiated.
Release 1.0 PacketCable Commands dqos res-req-trap-enable The dqos res-req-trap-enable command enables or disables a Resource Request SNMP trap through the DQoSResReq SNMP MIB object. If the Resource Request SNMP trap is enabled, the BSR generates an SNMP trap if a Resource Request from an MTA is invalid.
BSR 2000 Command Reference Guide Release 1.0 dqos shutdown The dqos shutdown command disables Dynamic QoS (DQoS) and COPS operation on the BSR.The no dqos shutdown command enables DQoS and the COPS operation on the BSR. Group Access All Command Mode PacketCable Configuration Command Line Usage dqos shutdown no dqos shutdown Command Default Disabled 16-22 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands dqos t0-timer/t1-timer If T0 and T1 timeouts are being counted in the show packet-cable statistics gate command output, the network and the PDP server need to be examined. T0 and T1 timers may need to be increased from their default values to avoid T0 and T1 timeouts. The dqos t0-timer and dqos t1-timer commands configure the T0 and T1 timers. The T0 timer specifies the period of time that a gate is allocated without being authorized.
BSR 2000 Command Reference Guide Release 1.0 em element-number The em element-number command specifies a unique event message Element ID for the BSR. The no em element-number command restores the default setting. Group Access All Command Mode PacketCable Configuration Command Line Usage em element-number <0-99999> no em element-number <0-99999> Command Syntax 0-99999 Element ID number Command Default 0 16-24 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands em event-disable-mask The em event-disable-mask command specifies a hexidecimal mask to disable event messages. The no em event-disable-mask command restores the default setting. The following table describes the QoS event message bit definitions. These hexidecimal values can also be combined. For example, QoS_Release and QoS_Commit event messages can be disabled by entering the hexidecimal number: 0x00040080.
BSR 2000 Command Reference Guide Release 1.0 em event-priority The em event-priority command specifies the priority of event messages generated from the BSR relative to other events. The no em event-priority command restores the default setting. Group Access All Command Mode PacketCable Configuration Command Line Usage em event-priority <0-255> no em event-priority <0-255> Command Syntax 0-255 event message priority value Command Default 128 16-26 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands em flag-override The Call Management Server directs the BSR (for PacketCable only) to send event messages to the Record Keeping Server in either batch mode (putting event messages together in a packet) or in realtime mode (sending event messages in packets as they come). The event flag, which tells the BSR to send event messages to the Record Keeping Server can be overridden.
BSR 2000 Command Reference Guide Release 1.0 em max-batch-events Event messages are batched together before being sent to the Record Keeping Server. The em max-batch-events command specifies the amount of event messages that are batched. The no em max-batch-events command restores the default setting. The collected messages are sent when the em max-batch-time parameter expires.
Release 1.0 PacketCable Commands em max-batch-time The hold-time for batched event messages can be specified to allow more time so that multiple event messages are combined into one packet to reduce network traffic. The em max-batch-time command specifies the interval that the batched event messages are held before they are sent to the Record Keeping Server. The no em max-batch-time command restores the default setting.
BSR 2000 Command Reference Guide Release 1.0 em qos-descriptor-disable The QoS Descriptor attribute can be disabled if an MSO administrator decides it does not need it because it wants to reduce the event message size for network traffic management purposes. The QoS descriptor attribute contains the Service Class profile name and QoS parameters. The em qos-descriptor-disable command disables the QoS Descriptor attribute. The no em qos-descriptor-disable command enables the QoS Descriptor.
Release 1.0 PacketCable Commands em retry-count If an Accounting-Response event message is not received by the BSR from the Record Keeping Server, the BSR sends the event message again. Once all retries are exhausted, the BSR tries an alternate Record Keeping Server (if one is available). The network and the Record Keeping Server should be examined to determine the reason for these timeouts.
BSR 2000 Command Reference Guide Release 1.0 em retry-interval The event message retry interval can be configured depending on the amount of network congestion and the distance between the BSR and the Record Keeping Server. For example, if the distance caused a time delay, the event message retry interval can be extended from the default value to allow more time for the BSR to receive an Accounting-Response message.
Release 1.0 PacketCable Commands em shutdown The em shutdown command disables event messages generated from the BSR if they are not needed. The no em shutdown command enables event messages. Group Access All Command Mode PacketCable Configuration Command Line Usage em shutdown no em shutdown Command Default Enabled 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 em udp-port If the default UDP port is already in use, another UDP port can be specified for PacketCable event messages. A different UDP port can also be specified for event messages because of security reasons. The em udp-port command specifies a UDP port number for event messages. The no em udp-port command restores the default setting.
Release 1.0 PacketCable Commands es The no es shutdown command enables electronic surveillance. The es shutdown command disables electronic surveillance. The es trap-enable enable command enables the electronic surveillance SNMP trap. The no es trap-enable disable command disables the electronic surveillance SNMP trap. Note: Electronic surveillance conforms to Communications Assistance for Law Enforcement Act (CALEA) requirements.
BSR 2000 Command Reference Guide Release 1.0 ike client-addr The ike client-addr command specifies the IP address used by the BSR for its source address during IKE protocol exchanges. Group Access All Command Mode IPSec Configuration Command Line Usage ike client-addr Command Syntax A.B.C.D 16-36 host IP address used for IKE MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands ike phase1 The IKE Phase 1 Lifetime Interval and IKE Phase 1 Lifesize can be specified to enhance security. These settings determine how long the key is exposed. For example, an MSO administrator can decide to update this key on a regular basis to prevent successful hacking.
BSR 2000 Command Reference Guide Release 1.0 ike phase2 The IKE Phase 2 Lifetime Interval and IKE Phase 2 Lifesize can be specified to enhance security. These settings determine how long the key is exposed. For example, an MSO administrator can decide to update this key on a regular basis to prevent successful hacking.
Release 1.0 PacketCable Commands ike retries The number of IKE retries can be specified for network problems. Observe the number of IKE retries in the show ipsec ike command output. If the number of IKE retries is increasing, then the network and server should be examined to determine the reason for the excessive number of IKE retries. The ike retries command specifies the number of IKE retries.
BSR 2000 Command Reference Guide Release 1.0 ike timeout The IKE retransmission timeout interval can be specified for network problems. Observe the number of IKE timeouts in the show ipsec ike command output. If the number of IKE timeouts is increasing, then the network and server should be examined to determine the reason for the excessive number of IKE timeouts. The ike timeout command specifies the IKE retransmission timeout interval.
Release 1.0 PacketCable Commands ipsec The ipsec command accesses IPSec Configuration mode from Global Configuration mode. Group Access All Command Mode Global Configuration and PacketCable Configuration Command Line Usage ipsec 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 ipsec shutdown The ipsec shutdown command disables IPSecIKE for the BSR.The no ipsec shutdown command enables IPSec/IKE for the BSR. Note: For the initial configuration of IPSec/IKE, the IPSec configurable parameters should be configured, before IPSec is enabled. At a minimum, the ike client-addr command should be configured prior to enabling IPSec.
Release 1.0 PacketCable Commands packet-cable The packet-cable command is used to access PacketCable Configuration mode from Global Configuration mode. Group Access All Command Mode Global Configuration Command Line Usage packet-cable 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 show cable dynamic-service The show cable dynamic-service command displays the dynamic service configuration status for the cable interfaces. The following provides typical screen output from the show cable dynamic-service command: Cable dynamic-service auth-mode: authorize Cable dynamic-service active-timeout: 0 Group Access All Command Mode Interface Configuration Command Line Usage show cable dynamic-service 16-44 MGBI 526363-001-00 Rev.
Release 1.0 PacketCable Commands show ipsec The show ipsec command displays the configuration of IKE, IPSec, Security Association Database (SADB), Security Policy Database (SPD), SPD preshared-keys, or SPD Policies.
BSR 2000 Command Reference Guide Release 1.0 show packet-cable configuration The show packet-cable configuration command displays COPS, DQoS, event messaging, electronic surveillance, and PacketCable Multimedia configuration information. The following provides typical screen output from the show packet-cable configuration command and output field descriptions: PacketCable Configuration ------------------------CMTS IP address: 150.31.50.
Release 1.0 PacketCable Commands Dynamic QoS Configuration displays if DQoS is enabled or disabled, T0 and T1 timer parameters, and whether the COPS status and Resource Request SNMP traps are enabled or disabled. Event Message Configuration displays if event messages are enabled or disabled and other event message configuration parameters Electronic Surveillance Configuration displays if ES is enabled or disabled and if the ES status SNMP trap is enabled or disabled.
BSR 2000 Command Reference Guide Release 1.0 show packet-cable cops The show packet-cable cops command display all COPS connections, which includes the COPS Client handle, PDP IP address, port number, keep-alive timeout, and duration time.
Release 1.0 PacketCable Commands Command Syntax inactive 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 PacketCable Commands Group Access All Command Mode All modes except User EXEC Command Line Usage show packet-cable gate [dqos | cops <0-3> | identifier <0x00000000-0xffffffff> | modem | slot | subscriber ] Command Syntax dqos specify all DQoS gates cops 0-3 specify a COPS connection and COPS handle to display identifier 0x00000000-0xffffffff Gate Identifier in hexadecimal notation to display detailed information about the DQoS or Multimedia gate.
BSR 2000 Command Reference Guide Release 1.0 show packet-cable statistics The show packet-cable statistics command displays COPS statistics, DQoS gate statistics, PacketCable Multimedia gate statistics, event message statistics, DQoS event message statistics, and electronic surveillance event message statistics.
Release 1.0 PacketCable Commands Command Line Usage show packet-cable statistics [em | es {identifier <0x00000000-0xffffffff>} | gate [cops [<0-99>]]] Command Syntax em display event message statistics es display electronic surveillance statistics identifier 0x00000000-0xffffffff gate identifier in hexadecimal notation gate display gate statistics cops gate statistics per COPS connection 0-99 COPS handle 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 spd allow-dynamic-rsp The spd allow-dynamic-rsp command allows a dynamic response from a peer to negotiate Internet Key Exchange (IKE) even though the SPD policy setting is other than the "APPLY" policy setting. The no spd allow-dynamic-rsp command is used to return the default setting. Group Access All Command Mode IPSec Configuration Command Line Usage spd allow-dynamic-rsp no spd allow-dynamic-rsp Command Default BSR strictly follows the configured SPD.
Release 1.0 PacketCable Commands spd override The spd override command is used to override IP addresses, ports, or protocols that are configured in the IPSec Security Policy Database (SPD). The no spd override is used to remove the address, port, or protocol override.
BSR 2000 Command Reference Guide Release 1.0 spd policy The spd policy command specifies a security policy for the given peers IPSec Security Policy Database (SPD). The SPD policy is priority based. The lower number index has a higher priority. Data packets are compared against rules in the SPD policy, starting with the first index. When a match is found, that rule is applied and no further comparisons are made against the SPD policy for that data packet.
Release 1.0 PacketCable Commands num transport protocol number which is the IP protocol from the IP protocol header. The format is a decimal number. A value of “0” represents any protocol. For example, the Call Management Server/Gate Controller or Call Management Server/Policy Server can use TCP Port 6 and the Record Keeping Server can use UDP Port 17. 0-65535 source TCP/UDP port number. “0” represents any port. 0-65535 destination TCP/UDP port number.
BSR 2000 Command Reference Guide Release 1.0 spd preshared-key The spd preshared-key command specifies the Pre-shared Key IP address to allow a Pre-shared secret key to be passed between parties in a communication flow to authenticate their mutual identities. The no spd preshared-key removes the Pre-shared Key IP address. Group Access All Command Mode IPSec Configuration Command Line Usage spd preshared-key no spd preshared-key Command Syntax 16-58 A.B.C.
17 VLAN Tagging Commands Introduction This chapter describes the commands used to configure and manage the VLAN Tagging on the BSR. VLAN Tagging allows the BSR to forward traffic received from a CPE connected to a bridging CM to a uniquely numbered VLAN using the 802.1Q industry-standard trunking encapsulation on a selected "bridge mode trunk" port. VLAN Tagging Command Descriptions This section contains an alphabetized list and descriptions of the VLAN Tagging commands supported by the BSR.
BSR 2000 Command Reference Guide Release 1.0 bridge cable modem The bridge cable modem command designates a particular cable modem as a bridging CM and associates its CPE traffic to a specified VLAN. Group Access All Command Mode Global Configuration Command Line Usage bridge cable modem <2-4094> [stackable] Command Syntax mac cable modem MAC Address in the form xxxx.xxxx.xxxx 2-4094 the VLAN ID stackable allows stacking of multiple IEEE 802.
Release 1.0 VLAN Tagging Commands bridge mode trunk The bridge mode trunk command enables VLAN tagged bridging on a network interface. Only the Ethernet Network Interface is permitted to be configured for VLAN Tagging. Group Access All Command Mode Interface Configuration (Ethernet and Gigaether only) Command Line Usage bridge mode trunk [priority <0-255>] Command Syntax 0-255 526363-001-00 Rev.
BSR 2000 Command Reference Guide Release 1.0 clear bridge vlan counters The clear bridge vlan counters command clears all receive and transmit statistics for all VLANs associated with a VLAN cable modem. These are the same statistics displayed with the show bridge vlan counters command. Group Access All Command Mode Privileged EXEC Command Line Usage clear bridge vlan counters [<2-4094>] Command Syntax 2-4094 17-4 the VLAN ID - if omitted, all VLAN counters are cleared MGBI 526363-001-00 Rev.
Release 1.0 VLAN Tagging Commands encapsulation dot1q The encapsulation dot1q command configures tagged routing on a bridge trunk port. This means that all layer 3 packets routed by the BSR that egress the port are tagged with a particular 802.1Q VLAN ID tag. The no encapsulation dot1q disables VLAN tagged routing.
BSR 2000 Command Reference Guide Release 1.0 show bridge vlan The show bridge vlan command displays bridge VLAN statistics including associated bridging cable modems and receive and transmit counts. The following is typical screen output from the show bridge vlan command: Selected Network Bridge Port: ethernet 0/0 Vlan CM ---- -------------2 0000.0000.0065 3 0000.0000.
Release 1.0 VLAN Tagging Commands Command Syntax counters display statistical counters for all VLANs or a specific VLAN associated with a network bridge port 2-4094 the VLAN ID - if omitted, all VLANs are displayed Note: VLAN ID 1 is reserved for use by the attached Layer 2 switch/router for management purposes and as the default "native" VLAN for that equipment. VLAN ID 1 may not be configured on the BSR for Ethernet port tagged routing or for cable modem Layer 2 bridging. 526363-001-00 Rev.
A Command Defaults This Appendix provides a list of default values or default states for BSR 2000 commands. Those commands for which the Default column is left blank do not have a default value associated with them.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Table A-2 IP Commands Command Default arp No entries in table arpa (ethernet ARP) arp timeout cable helper-address clear arp-cache clear counters clear host clear ip route clear ip traffic host authorization Disabled interface ip access-group No access groups defined ip address ip broadcast-address ip dhcp relay information ip domain-list ip domain-lookup Enabled ip domain-name No domain is configured.
Release 1.0 Command Defaults Table A-2 IP Commands Command Default ip proxy-arp Disabled ip rarp-server Disabled ip redirects ip route administrative distance = 1 ip routing Enabled ip source-route ip unreachables Enabled passive-interface Routing updates are transmitted over the router.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Table A-5 Access List Commands Command Default access-class in access-list (standard) access-list (extended) ip access-group ip access-list show access-lists All access lists are displayed.
Release 1.0 Command Defaults Table A-6 Routing Policy Commands Command Default set automatic-tag set comm-list set community set default interface null0 Disabled set interface null0 Disabled set ip default next-hop set ip diff-serv 0 set ip next-hop Disabled set ip qos queue set local-preference set metric Metric value dynamically learned or a default value set metric-type Disabled set origin set tag If not specified, tag is forwarded to the new destination protocol.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 Command Defaults Table A-8 OSPF Commands Command Default area nssa No NSSA area is defined.
BSR 2000 Command Reference Guide Release 1.
Release 1.0 Command Defaults Table A-10 IP Multicast Commands Command Default ip mroute ip mroute static distance ip mroute unicast distance ip multicast-routing Disabled show ip rpf clear ip multicast fwd-cache clear ip multicast proto-cache mtrace Group address or group hostname = 224.2.0.
BSR 2000 Command Reference Guide Release 1.0 Table A-11 CMTS Commands Command Default cable downstream carrier-only Modulation to the RF carrier is disabled. cable downstream description cable downstream frequency 555000000 Hz cable downstream interleave-depth The command default is 8 for North American DOCSIS.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Table A-11 CMTS Commands Command Default cable upstream minislot-size Channel Width Minislot Size 3200000 Hz 4 ticks 1600000 Hz 8 ticks 800000 Hz 16 ticks 400000 Hz 32 ticks 200000 Hz 64 ticks cable upstream modem-ranging-delay 250 microseconds cable upstream modulation-profile modulation profile 1 cable upstream physical-delay The fixed physical delay is 400 microseconds.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 Table A-17 VLAN Tagging Commands Command Default bridge cable modem bridge mode trunk clear bridge vlan counters encapsulation dot1q show bridge vlan A-32 MGBI 526363-001-00 Rev.
Index A auto-virtual link, 8-10 aaa accounting commands default, 1-3 aaa accounting exec default, 1-5 B aaa authentication enable default, 1-7 balance, 11-3 aaa authentication local-override, 1-9 band, 11-3 aaa authorization commands default, 1-11 banner motd, 1-19 aaa authorization exec default, 1-13 batch, 1-20 aaa console authentication, 1-14 bgp always-compare-med, 12-4 aaa console authorization commands default, 1-15 bgp confederation identifier, 12-5 aaa new-model, 1-16 bgp confederati
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.
Release 1.
BSR 2000 Command Reference Guide Release 1.0 U undebug all, 4-48 update-fpga, 1-163 username, 1-164 username privilege, 1-166 username user-group, 1-167 V version, 7-30 Index-12 MGBI 526363-001-00 Rev.
Visit our website at: www.motorola.com 526363-001-00 Rev.
