AP6562 Access Point INSTALLATION GUIDE
AP6562 Access Point MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions, Inc. 2013. All rights reserved.
Installation Guide 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.
AP6562 Access Point 5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5.1 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5.2 Wireless Device Country Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5.2.1 Country Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5.2.
Installation Guide 5 1 Introduction The AP6562 access point, a component of the Motorola Solutions wireless controller system, links wireless 802.11abgn devices, enabling the growth of your wireless network with a cost effective alternative to standard access points. The AP6562 access point provides multiple deployment options. The AP6562 access point receives all power and transfers data through the same CAT-5 or better Ethernet cable. An 802.
AP6562 Access Point 1.2 Warnings • • • • • Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the access point. Remove jewelry and watches before installing this equipment. Verify the unit is grounded before connecting it to the power source. Verify any device connected to this unit is properly wired and grounded.
Installation Guide 7 1.4.2 External Antenna Model Package Contents Part Number Description AP-6562-66040-US AP6562 Outdoor Dual Radio 802.11N US AP-6562-66040-WR AP6562 Outdoor Dual Radio 802.11N INTL AP-6562-66040-EU AP6562 Outdoor Dual Radio 802.11N EU AP6562 external antenna models (AP-6562-66040-US, AP-6562-66040-WW and AP-6562-66040-EU) include the following: • • • AP6562 access point with external antenna connectors Weatherproof RJ45 plug kit AP6562 Installation Guide (This Guide) 1.4.
AP6562 Access Point 2 Hardware Installation 2.1 Installation Instructions To prepare for the installation: 1. Match the model number on the purchase order with the model numbers in the packing list and on the case of the access point. 2.
Installation Guide 9 2.3 AP6562 Hardware Mounting and Installation It is recommended to use the AP6562 mounting bracket kit (KT-147407-01) for most deployments. When a standoff distance is required for a pole mounted or wall mounted installation, use the extension arm kit (KT-150173-01). 2.3.
AP6562 Access Point A torque wrench or ratchet with a 10mm adapter, or an adjustable wrench, can be used to assemble the mounting brackets. A finished assembly of the mounting bracket kit is shown below. Assembly during deployment may differ to achieve the required angle and rotation. 2.3.
Installation Guide 11 The extension arm kit can also be used in combination with the any of the brackets from the mounting bracket kit. The following ancillary hardware to attach the extension arm to the mounting bracket kit sections is included in the extension arm kit: Description Quantity 1/2 inch hex head nut 2 1/2 inch x 3/4 inch hex head bolt 2 2.3.
AP6562 Access Point NOTE The extension arm is recommended for installations on poles greater than 3 inches in diameter. 2.3.4 Vertical Pole Mount Use the following procedures for vertical pole mount installations. The extension arm is recommended when mounting the access point to poles greater than 3 inches is diameter. For poles up to 3 inches in diameter when using a U-bolt 1. Thread the two inner nuts onto the U-bolt. Place the U-bolt at the desired mounting location. 2.
Installation Guide 13 15. Verify the unit has power by observing that the LEDs are lit or flashing. CAUTION ! If not using a 802.3at capable controller to power the AP6562, ensure only the AP6562’s designated outdoor power supply (AP-PSBIAS-7161-US or AP-PSBIAS-7161-WW) is used to supply power to the access point. Using an incorrectly rated power supply could damage the unit and void the product warranty.
AP6562 Access Point 11. Verify the unit has power by observing that the LEDs are lit or flashing. CAUTION ! If not using a 802.3at capable controller to power the AP6562, ensure only the AP6562’s designated outdoor power supply (AP-PSBIAS-7161-US or AP-PSBIAS-7161-WW) is used to supply power to the access point. Using an incorrectly rated power supply could damage the unit and void the product warranty.
Installation Guide 15 2.3.5 Wall Mounted Installation For wall mounted installations, use only the access point bracket and if required the angle adapter bracket. The access point can also be installed using the sheet metal tab on the top of the enclosure. NOTE The U-bolt and band clamps are not included in the mounting bracket kit. NOTE The lag bolts are not included in the mounting bracket kit. 1.
AP6562 Access Point CAUTION ! If not using a 802.3at capable controller to power the AP6562, ensure only the AP6562’s designated outdoor power supply (AP-PSBIAS-7161-US or AP-PSBIAS-7161-WW) is used to supply power to the access point. Using an incorrectly rated power supply could damage the unit and void the product warranty. Do not actually connect to the power source until the cabling portion of the installation is complete. To use only the extension arm: 1.
Installation Guide 17 2.4 AP6562 Internal Antenna Model AP6562 internal antenna models (AP-6562-66030-US, AP-6562-66030-WR and AP-6562-66030-EU) are configured with four internal antennas.
AP6562 Access Point 2.5 AP6562 External Antenna Model AP6562 external antenna models (AP-6562-66040-US, AP-6562-66040-WR and AP-6562-66040-EU) are configured with four external N type connectors.
Installation Guide NOTE 19 If an antenna connector is unused, the open connector must be covered with an appropriate threaded metal or plastic antenna connector cover. The labels for Radio 1-0, Radio 1-1, Radio 2-0 and Radio 2-1 are molded into the AP6562 access point enclosure beside the antenna connectors. When mounting antennas to the connectors, ensure that you have selected the appropriate band for the configured radio. Radio 1 is a 2.4 GHz radio.
AP6562 Access Point 2.6 AP6562 LED Indicators Both internal antenna and external antenna models have LED activity indicators on the front of the case.
Installation Guide 21 The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11an (amber) radio or the 2.4 GHz 802.11bgn (green) radio. Task 5 GHz Activity LED (Amber) 2.
AP6562 Access Point 3 Basic Access Point Configuration Once the Access Point is installed and powered on, complete the following steps to get the device up and running and access management functions: 1. Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source or use the designated outdoor rated power supply (AP-PSBIAS-7161-US or AP-PSBIAS-7161-WW) to supply power to the AP6562 (once fully cabled).
Installation Guide 23 3. Enter the default username admin in the Username field. 4. Enter the default password motorola in the Password field. 5. Click the Login button to load the management interface. NOTE When logging in for the first time, you’re prompted to change the password to enhance device security in subsequent logins. NOTE If you get disconnected when running the wizard, you can connect again with the Access Point’s actual IP address (once obtained) and resume the wizard. 6.
AP6562 Access Point NOTE The Initial Setup Wizard displays the same pages and content for each Access Point model supported. The only difference being the number of radios configurable by model, as an AP7131 model can support up to three radios, AP6522, AP6532, AP6562, AP8132 and AP7161 models support two radios and AP6511 and AP6521 models support a single radio. The Introduction screen displays the various actions that can be performed using the wizard under the Function Highlight field.
Installation Guide 25 7. Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to the next page listed in the Navigation Panel without saving your updates. NOTE While you can navigate to any page in the navigation panel, you cannot complete the Initial AP Setup Wizard until each task in the Navigation Panel has a green checkmark.
AP6562 Access Point • Standalone AP - Select this option to deploy this Access Point as an autonomous fat Access Point. A Standalone AP isn't managed by a Virtual Controller AP, or adopted by a controller. NOTE If wanting to adopt the Access Point to a controller or service platform, use the controller or service platform’s resident UI to connect to the Access Point, provision its configuration and administrate the Access Point’s configuration.
Installation Guide 27 13. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point handles network traffic. 14. Select an Access Point Mode from the available options. • Router Mode -In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point.
AP6562 Access Point 15. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration. 16. Set the following DHCP and Static IP Address/Subnet information for the LAN interface: • Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Point’s DHCP server. • Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's LAN interface.
Installation Guide 29 • DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP addresses. If this option is not selected, a primary and secondary DNS resource must be specified. DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible for converting the name into its corresponding IP address, cannot locate the matching IP address.
AP6562 Access Point 19. Select Next. The Typical Setup Wizard displays the RADIUS Server Configuration screen if required. Otherwise, the Typical Setup Wizard displays the Summary and Commit screen. 20. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use the screen to add, modify and remove RADIUS users.
Installation Guide 31 21. Select Add User to display the dialog to enter user information to add to the RADIUS server user database. 22. Enter the following user information: • Username - Provide a user name used to authenticate the user. • Password - Provide a password used to authenticate the user. • Confirm Password - Confirm the password by entering the same password as entered in the Password field. • Description - Provide a description to identify the user created in the RADIUS server database. 23.
AP6562 Access Point 28. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings updated using the Typical Setup Wizard. No user intervention or additional settings are required. Its an additional means of validating the Access Point’s updated configuration before it’s deployed.
Installation Guide 33 4 Specifications 4.1 AP6562 Internal Antenna Model Power Specifications An AP6562 internal model access point has the following power specifications: Operating voltage 36-57 VDC Power in (PoE) 802.3at 4.2 AP6562 Internal Antenna Model Physical Specifications An AP6562 internal antenna model access point has the following physical specifications: Dimensions 9.1 in W x 9.8 in H x 2.6 in D 23.1cm W x 24.9cm H x 24.
AP6562 Access Point 4.4 AP6562 External Antenna Model Power Specifications An AP6562 external antenna model access point has the following power specifications: Operating voltage 36-57 VDC Power in (PoE) 802.3at 4.5 AP6562 External Antenna Model Physical Specifications An AP6562 external antenna model access point has the following physical specifications: Dimensions 9.1 in W x 9.8 in H x 2.6 in D 23.1cm W x 24.9cm H x 24.
Installation Guide 35 4.6 Radio Specifications AP6562 model access points have the following radio specifications: Data rates supported 802.11b/g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps 802.11a: 6,9,12,18,24,36,48, and 54Mbps 802.11n: MCS 0-15 up to 300Mbps Network standard 802.11a, 802.11b, 802.11g, 802.
AP6562 Access Point 5 Regulatory Information 5.1 Regulatory Information This device is approved under Motorola Solutions, Inc. This guide applies to MODEL: AP6562 All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following web site: http://www.motorolasolutions.
Installation Guide 37 5.2.2 Frequency of Operation – FCC and IC You are reminded of the need to observe restrictions on the radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders). 5 GHz Only The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor Use Only; any other use will make the operation of this device illegal.
AP6562 Access Point 5.3.3 Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.
Installation Guide 39 5.7 US and Canada Co-located statement To comply with FCC RF exposure compliance requirement, the antennas used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling.
AP6562 Access Point 5.10 Radio Frequency Interference Requirements – Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s) Rules.
Installation Guide 41 5.11 CE Marking and European Economic Area (EEA) The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions: • • • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz. France outside usage, the equipment is restricted to 2.400-2.45 GHz frequency range. Italy requires a user license for outside usage. 5.
AP6562 Access Point Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. "La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada." Taiwan 在 5.25-5.
Installation Guide 5.14 43 Waste Electrical and Electronic Waste Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Motorola Solutions for recycling. For information on how to return product, please go to: http://www.motorolasolutions.com/recycling/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Motorola Solutions pour recyclage.
AP6562 Access Point Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola Solutions til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.motorolasolutions.com/recycling/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Motorola Solutions για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.
Installation Guide 45 6 Motorola Solutions Support Center If you have a problem with your equipment, contact support for your region. Contact information is available at: http://www.motorolasolutions.com/support.
AP6562 Access Point 7 AP6562 Access Point China ROHS Compliance 有毒有害物质或元素 部件名称 (Parts) 金属部件 (Metal Parts) 电路模块 (Circuit Modules) 电缆及电缆组件 (Cables and Cable Assemblies) 塑料和聚合物部件 (Plastic and Polymeric Parts) 光学和光学组件 (Optics and Optical Components) 电池 (Batteries) 六价铬 (Cr6+) 15 多溴二苯 醚 (PBDE) O 铅 (Pb) 汞 (Hg) 镉 (Cd) O O O O 多溴联 苯 (PBB) O X O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以 下。 X：表示该有毒有害物质至少在
Installation Guide 47
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All Rights Reserved.
