M Motorola Solutions AP-7131N-FGR Product Reference Guide
MOTOROLA, MOTO, MOTOROLA Solutions and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are a properties of their owners. ©2014 Motorola Solutions, Inc. All rights reserved.
AP-7131N-FGR Access Point Product Reference Guide
Contents Chapter 1. Introduction New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 IP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 MU Rate Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Per Radio MU Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Content Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13 VLAN Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14 Multiple Management Accessibility Options . . . . . . . . . . . . . . . . . . . . . . . . .1-14 Updatable Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Chapter 2. Hardware Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Access Point Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Testing Connectivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17 Where to Go from Here? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18 Chapter 4. System Configuration Configuring System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 Configuring Power Settings . . . . . . . . . . . . . . . . . . . .
5 Configuring WLAN Security Policies . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34 Configuring a WLAN Access Control List (ACL) . . . . . . . . . . . . . . . . . . . 5-35 Setting the WLAN Quality of Service (QoS) Policy . . . . . . . . . . . . . . . . . 5-39 Configuring WLAN Hotspot Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45 Setting the WLAN’s Radio Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-51 Configuring the 802.11a/n or 802.
6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Configuring LDAP Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-57 Configuring a Proxy Radius Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-59 Managing the Local User Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-61 Wireless Users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-61 Management Users . .
7 Network WAN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-40 Network WAN NAT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-43 Network WAN, VPN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-49 Network WAN, Dynamic DNS Commands . . . . . . . . . . . . . . . . . . . . . . . 8-62 Network Wireless Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-66 Network WLAN Commands. . . . .
8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Client Bridge Configuration Process Example . . . . . . . . . . . . . . . . . . . . . .9-4 Spanning Tree Protocol (STP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4 Defining the Mesh Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4 Mesh Networking and the Access Point’s Two Subnets. . . . . . . . . . . . . . . . . .9-5 Normal Operation. . . . . . . . . . . . .
9 Adaptive Mesh Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6 Supported Adaptive AP Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-7 Topology Deployment Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-7 Extended WLANs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-8 Independent WLANs Only . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
About This Guide Introduction This guide provides configuration and setup information for the AP-7131N-FGR model access point. Document Conventions The following document conventions are used in this document: NOTE Indicate tips or special requirements. CAUTION Indicates conditions that can cause equipment damage or data loss. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage.
viii Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Notational Conventions The following notational conventions are used in this document: • • • Italics are used to highlight specific items in the general text, and to identify chapters and sections in this and related documents.
Introduction As a standalone access point, an AP-7131N-FGR provides small and medium-sized businesses with a consolidated wired and wireless networking infrastructure, all in a single device. The integrated router, gateway, firewall, DHCP and Power-over-Ethernet (PoE) simplify and reduce the costs associated with networking by eliminating the need to purchase and manage multiple devices.
1-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide If you are new to using an access point for managing your network, refer to Theory of Operations on page 1-23 for an overview on wireless networking fundamentals. Beginning with the 4.x access point firmware baseline, Motorola Solutions is introducing an AP-7131N-FGR model access point as a compliment to the existing AP-7131 access point family.
Introduction 1.1.1 IP Filtering IP filtering determines which IP packets are processed normally and which are discarded. If discarded, the packet is deleted and completely ignored (as if never received). Optionally apply different criteria to better refine which packets to filter. IP filtering supports the creation of up to 20 filter rules enforced at layer 3. Once defined (using the access point’s SNMP, GUI or CLI), filtering rules can be enforced on the access point’s LAN1, LAN2 and WLAN interfaces.
1-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide For information on setting the number of MU associations on a specific radio, see Configuring the 802.11a/n or 802.11b/g/n Radio on page 5-56. 1.1.4 Power Setting Configuration The access point’s power management functionality automatically configures the AP's operational mode so it safely operates within available power.
Introduction 1.1.6 IPSec VPN Support A VPN ensures data privacy between two end points, even while using a communication medium which is itself insecure (like the Internet). VPNs create a secure tunnel between two end points as if they are directly connected over a secure connection. Traffic is secured using a robust IPSec encryption technique. You can get the safety of a VPN in a WLAN by hosting the VPN server at the access point, and the VPN client software on the MU.
1-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • • • • • • • • • • • • • • • • • • • MU-MU Transmission Disallow Voice Prioritization Support for CAM and PSP MUs Statistical Displays Transmit Power Control Advanced Event Logging Capability Configuration File Import/Export Functionality Default Configuration Restoration DHCP Support Mesh Networking Additional LAN Subnet On-board Radius Server Authentication Hotspot Support Routing Information Protocol (RIP) Manual Date and Ti
Introduction network vulnerabilities in real time and permits both a wired and wireless lockdown of wireless device connections upon acknowledgement of a threat. An access point radio can function as a sensor and upload sensor mode operation information to a dedicated WIPS server. WIPS is not supported on a WLAN basis, rather sensor functionality is supported on the access point radio(s) available to each WLAN.
1-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide A radio in sensor mode supports three basic features: NOTE The functions described below are conducted on the WIPS server side, not on the access point. • • • • Wireless Termination - The access point attempts to force an unwanted (or unauthorized) connection to disconnect. Wireless Sniffing - All received frames are reported to the WIPS server.
Introduction define how WIPS can be supported on an access point radio, see Configuring Device Settings on page 3-8. 1.2.3 Mesh Roaming Client Enable the Mesh Roaming Client feature (using the access point’s CLI) to allow a client bridge to associate in the same manner as a regular mesh client bridge. After an initial (single) association, the client bridge will not attempt additional associations. Since STP will be disabled, the association forwards data as soon as the association attempt is successful.
1-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide For detailed information on configuring the access point’s WAN port, see Configuring WAN Settings on page 5-16. The LAN and WAN port MAC addresses can be located within the LAN and WAN Stats screens. For detailed information on locating the access point’s MAC addresses, see Viewing WAN Statistics on page 7-2 and Viewing LAN Statistics on page 7-6.
Introduction If the radio MAC address displayed on the Radio Settings screen is 00:23:68:72:20:DC, then the BSSIDs for that radio will have the following MAC addresses: BSSID MAC Address Hexadecimal Addition BSSID #1 00:23:68:72:20:DC Same as Radio MAC address BSSID #2 00:23:68:72:20:DD Radio MAC address +1 BSSID #3 00:23:68:72:20:DE Radio MAC address +2 BSSID #4 00:23:68:72:20:DF Radio MAC address +3 For detailed information on strategically mapping BSSIDs to WLANs, see Configuring the 802.
1-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • EAP Authentication The following encryption techniques are supported: • WPA2-CCMP (802.11i) Encryption In addition, the access point supports the following additional security features: • • • Firewall Security VPN Tunnels Content Filtering For an overview on the encryption and authentication schemes available , refer to Configuring Access Point Security on page 6-1. 1.2.11.
Introduction the Advanced Encryption Standard (AES). CCMP computes a Message Integrity Check (MIC) using the proven Cipher Block Message Authentication Code (CBC-MAC) technique. Changing just one bit in a message produces a totally different result. WPA2-CCMP is based on the concept of a Robust Security Network (RSN), which defines a hierarchy of keys with a limited lifetime . Messages are encrypted using a 128-bit secret key and a 128-bit block of data.
1-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1.2.12 VLAN Support A Virtual Local Area Network (VLAN) can electronically separate data on the same AP from a single broadcast domain into separate broadcast domains. By using a VLAN, you can group by logical function instead of physical location. There are 16 VLANs supported on the access point. An administrator can map up to 16 WLANs to 16 VLANs and enable or disable dynamic VLAN assignment.
Introduction 1.2.15 Programmable SNMP v3 Trap Support Simple Network Management Protocol (SNMP) facilitates the exchange of management information between network devices. SNMP uses Management Information Bases (MIBs) to manage the device configuration and monitor Internet devices in remote locations. MIB information accessed via SNMP is defined by a set of managed objects called Object Identifiers (OIDs). An OID is used to uniquely identify each object variable of a MIB.
1-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1.2.16 Power-over-Ethernet Support When users purchase a Motorola Solutions WLAN solution, they often need to place access points in obscure locations. In the past, a dedicated power source was required for each access point in addition to the Ethernet infrastructure. This often required an electrical contractor to install power drops at each access point location.
Introduction For detailed information on configuring voice prioritization over other voice enabled devices, see Setting the WLAN Quality of Service (QoS) Policy on page 5-39. 1.2.19 Support for CAM and PSP MUs The access point supports both CAM and PSP powered MUs. CAM (Continuously Aware Mode) MUs leave their radios on continuously to hear every beacon and message transmitted. These systems operate without any adjustments by the access point.
1-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1.2.22 Advanced Event Logging Capability The access point periodically logs system events. Logging events is useful in assessing the throughput and performance of the access point or troubleshooting problems on the access point managed Local Area Network (LAN). For detailed information on access point events, see Logging Configuration on page 4-45. 1.2.
Introduction The DHCP client automatically sends a DHCP request at an interval specified by the DHCP server to renew the IP address lease as long as the access point is running (this parameter is programmed at the DHCP server). For example: Windows 2000 servers typically are set for 3 days. 1.2.
1-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide For an overview on mesh networking as well as details on configuring the access point’s mesh networking functionality, see Configuring Mesh Networking on page 9-1. 1.2.27 Additional LAN Subnet In a typical retail or small office environment (wherein a wireless network is available along with a production WLAN) it is often necessary to segment a LAN into two subnets.
Introduction authentication device. The access point issues an IP address to the user using a DHCP Server, authenticates the user and grants the user to access the Internet. If a tourist visits a public hotspot and wants to browse a Web page, they boot their laptop and associate with a local Wi-Fi network by entering a valid SSID.
1-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1.2.33 Auto Negotiation Auto negotiation enables the access point to automatically exchange information about data transmission speed and duplex capabilities. Auto negotiation is helpful when using the access point in an environment where different devices are connected and disconnected on a regular basis.
Introduction For more information on defining access point access policies by group, see Defining User Access Permissions by Group on page 6-67. 1.2.37 QBSS Support Each access point radio can be configured to optionally allow the access point to communicate channel usage data to associated devices and define the beacon interval used for channel utilization transmissions. The QBSS load represents the percentage of time the channel is in use by the access point and the access point’s station count.
1-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • • • • • • • • Wireless Coverage MAC Layer Bridging Content Filtering DHCP Support Media Types Direct-Sequence Spread Spectrum MU Association Process Operating Modes Management Access Options MAC Address Assignment 1.3.1 Wireless Coverage An access point establishes an average communication range with MUs called a Basic Service Set (BSS) or cell.
Introduction 1.3.2 MAC Layer Bridging The access point provides MAC layer bridging between its interfaces. The access point monitors traffic from its interfaces and, based on frame address, forwards the frames to the proper destination. The access point tracks source and destination addresses to provide intelligent bridging as MUs roam or network topologies change. The access point also handles broadcast and multicast messages and responds to MU association requests.
1-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1.3.4 Direct-Sequence Spread Spectrum Spread spectrum (broadband) uses a narrowband signal to spread the transmission over a segment of the radio frequency band or spectrum. Direct-sequence is a spread spectrum technique where the transmitted signal is spread over a particular frequency range. The access point uses Direct-Sequence Spread Spectrum (DSSS) for radio communication.
Introduction MUs perform partial scans at programmed intervals, when missing expected beacons or after excessive transmission retries. In a partial scan, the MU scans access points classified as proximate on the access point table. For each channel, the MU tests for Clear Channel Assessment (CCA). The MU broadcasts a probe with the ESSID and broadcast BSS_ID when the channel is transmission-free. It sends an ACK to a directed probe response from the access point and updates the table.
1-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • PPPoE - The WAN interface can terminate a PPPoE connection, thus enabling the access point to operate in conjunction with a DSL or Cable modem to provide WAN connectivity. • NAT - (Network Address Translation) on the Wireless interface. Using NAT, the router is able to manage a private IP scheme. NAT allows translation of private addresses to the WAN IP address. • DHCP - The access point can assign private IP addresses.
Introduction Table 1.2 Acronyms Portal Radio of an AP MU Mobile Unit Make configuration changes to access point’s individually. Optionally, use the access point import/export configuration function to download settings to other access points. For detailed information, see Importing/Exporting Configurations on page 4-47. 1.3.8 MAC Address Assignment MAC address assignments are as follows: • • • • • LAN (GE1) - The access point MAC address can be found underneath the access point chassis.
1-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
Hardware Installation An AP-7131N-FGR access point installation includes mounting the access point, connecting the access point to the network, connecting antennae and applying power. Installation procedures vary for different environments.
2-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION Motorola Solutions recommends conducting a radio site survey prior to installing an access point. A site survey is an excellent method of documenting areas of radio interference and providing a tool for device placement. 2.1 Precautions Before installing an AP-7131N-FGR model access point, verify the following: • • Do not install in wet or dusty areas without additional protection.
Hardware Installation Contact the Motorola Solutions Support Center to report missing or improperly functioning items. NOTE The access point façade with 6 Element Antenna (Part No. ML-2452-PTA2M3X3-1) is separately orderable and provides an integrated antenna option. The facade connects to the access point as illustrated. Once attached, the LEDs continue to illuminate through the facade. Contact your Motorola Solutions sales associate for information on ordering a facade with your access point. 2.
2-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • Install the access point at an ideal height of 10 feet from the ground. Orient the access point antennas vertically for best reception. Point the access point antennas downward if attaching to the ceiling. To maximize the access point’s radio coverage area, Motorola Solutions recommends conducting a site survey to define and document radio interference obstacles before installing the access point. 2.4.
Hardware Installation R1 defines the access point’s radio 1 antenna connectors and R2 defines radio 2 antenna connectors. The 2.4 GHz antenna suite includes the following models: Part No. Antenna Type Approximate Gain (dBi) ML-2499-11PNA2-01R Wide Angle Directional 8.5 ML-2499-HPA3-01R Omni-Directional Antenna 3.3 ML-2499-BYGA2-01R Yagi Antenna 13.9 ML-2452-APA2-01 Dual-Band 3/4 ML-2452-PTA2M3X3-1 Facade with 6 Element Antenna Module 3/5 ML-2452-PTA3M3-036 3 Port MIMO Antenna 4.75/5.
2-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The 5 GHz antenna suite includes the following models: Part No. Antenna Type Approximate Gain (dBi) ML-5299-WPNA1-01R Panel Antenna 13 ML-5299-HPA1-01R Wide-Band Omni-Directional Antenna 5.0 ML-2452-APA2-01 Dual-Band 3/4 ML-2452-PTA2M3X3-1 Facade with 6 Element Antenna 4.75/5.5 Module ML-2452-PTA3M3-036 3 Port MIMO Antenna 5/5 ML-2452-APA6J-01 Dipole 2.4GHz Peak Gain: -5.76dBi 5GHz Peak Gain: band 1: -3.
Hardware Installation When users purchase a WLAN solution, they often need to place access points in obscure locations. In the past, a dedicated power source was required for each access point in addition to the Ethernet infrastructure. This often required an electrical contractor to install power drops at each access point location.
2-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION The access point supports any standards-based compliant power source (including non-Motorola Solutions power sources). However, using the wrong solution (including a POE system used on a legacy Motorola Solutions access point) could either limit functionality or severely damage the access point and void the product warranty. 2.6.
Hardware Installation • The Power Injector is not a repeater, and does not amplify the Ethernet data signal. For optimal performance, ensure the unit is placed as close as possible to the network data port. CAUTION To avoid problematic performance and restarts, disable POE from a wired switch port connected to an access point if mid-span power sourcing equipment (PSE) is used between the two, regardless of the manufacturer of the switch. 2.6.1.
2-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2.7 Mounting an AP-7131N-FGR An AP-7131N-FGR can attach to a wall, mount under a suspended T-Bar or above a ceiling (plenum or attic) following the same installation instructions. Choose one of the following mounting options based on the physical environment of the coverage area. Do not mount the access point in a location that has not been approved in a site survey.
Hardware Installation 2-11
2-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Xerox copy the template (on the previous page) to a blank piece of paper. Do not reduce or enlarge the scale of the template. CAUTION If printing the mounting template (on the previous page) from an electronic PDF, dimensionally confirm the template by measuring each value for accuracy. 2. Tape the template to the wall mounting surface.
Hardware Installation 10. Cable the access point using either the Power Injector solution or an approved line cord and power supply. For Power Injector installations: a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the Power Injector Data In connector. b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out connector and the access point’s GE1/POE port. c.
2-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide To install the access point on a ceiling T-bar: 1. Motorola Solutions recommends you loop a safety wire—with a diameter of at least 1.01 mm (.04 in.), but no more than 0.158 mm (.0625 in.) —through the tie post (above the console connector) and secure the loop. 2. If desired, install and attach a security cable to the access point’s lock port. 3. Attach the radio antennas to their correct connectors.
Hardware Installation 9. Push the back of the access point chassis on to the bottom of the ceiling T-bar. CAUTION Ensure the safety wire and cabling used in the T-Bar installation is securely fastened to the building structure in order to provide a safe operating environment. 10. Rotate the access point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar. 11. The access point is ready to configure.
2-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The AP-7131N-FGR is Plenum rated to UL2043 and NEC1999 to support above the ceiling installations. CAUTION Motorola Solutions does not recommend mounting the access point directly to any suspended ceiling tile with a thickness less than 12.7mm (0.5in.) or a suspended ceiling tile with an unsupported span greater than 660mm (26in.).
Hardware Installation 8. Connect the light pipe to the bottom of the access point. Align the tabs and rotate approximately 90 degrees. Do not over tighten 9. Fit the light pipe into hole in the tile from its unfinished side. 10. Place the decal on the back of the badge and slide the badge onto the light pipe from the finished side of the tile. 11. Attach the radio antennas to their correct connectors. For more information on available antennas, see Antenna Options on page 2-4. 12.
2-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The Power Injector receives power as soon as AC power is applied. For more information on using the Power Injector, see Power Injector System on page 2-6. For standard 48-Volt Power Adapter (Part No. 50-14000-247R) and line cord installations: a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the access point’s GE1/POE port. b.
Hardware Installation NOTE Depending on how the 5 GHz and 2.4 GHz radios are configured, the LEDs will blink at different intervals between amber and yellow (5 GHz radio) and emerald and yellow (2.4 GHz radio). The LEDs on the top housing of the access point are clearly visible in wall and below ceiling installations.
2-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2.8.1 Dual Radio (2.4/5 GHz) LEDs A dual radio (2.4/5 Ghz) model access point has the following unique LED behavior: LED 1 LED 2 (LAN) LED 3 (WAN) LED 4 - 5 GHz LED 5 - 2.4 GHz Blinking Red indicates booting.Solid Red defines the diagnostic mode. White defines normal operation. Green defines normal GE1 operation. Green defines normal GE2 operation. Blinking Amber indicates 802.11a activity.
Hardware Installation 2.8.2 Rear LED The LED on the rear (bottom) of the access point is optionally viewed using a single (customer installed) extended light pipe, adjusted as required to suit above the ceiling installations. The LED light pipe has the following color display and functionality: LED 7 Blinking Red (160 msec) indicates a failure condition. Solid Red defines the diagnostic mode. White defines normal operation. 2.9 Setting Up MUs 2.9.
2-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2.9.2 802.11n MUs Third-party 802.11n clients can connect to the access point using default settings with no additional user intervention. However, there could be instances where the specific (high-performance) 802.11n settings cannot be sustained due to adverse radio traffic conditions within the network.
Hardware Installation NOTE If re-enabling the adapter for 802.11 support, ensure additional 802.11n settings (Aggregation, Channel Width, Guard Interval etc.) are also enabled to ensure optimal operation. 7. Click OK to save the updates to the adapter’s configuration.
2-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
Getting Started The access point should be installed in an area tested for radio coverage using one of the site survey tools available to the field service technician. Once an installation site has been identified, the installer should carefully follow the hardware precautions, requirements, mounting guidelines and power options outlined in Hardware Installation. See the following sections for more details: • • • Installing the Access Point Configuration Options Basic Configuration 3.
3-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • For instructions on mounting the access point to a wall, see Wall Mounted Installations on page 2-10. For instructions on mounting an access point to a ceiling T-bar, see Suspended Ceiling T-Bar Installations on page 2-13. For instructions on installing the access point in an above the ceiling attic space, see Above the Ceiling (Plenum) Installations on page 2-15.
Getting Started 3.3 Initially Connecting to the Access Point NOTE The procedures described below assume this is the first time you are connecting to an AP-7131N-FGR model access point. NOTE The computer being used should be configured to use the same IP address and subnet mask as the access point. 3.3.1 Connecting to the Access Point using the WAN Port To initially connect to the access point using the access point’s WAN port: 1.
3-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide As this is the first time you are logging into the access point, you are prompted to enter a new password and set the county code. Refer to Country Codes on page A-4 for a list of each available countries two digit country code. 6. At the CLI prompt (admin>), type “summary.” The access point’s LAN IP address will display. 7. Using a Web browser, use the access point’s IP address to access the access point. 8.
Getting Started 4. Enter the IP address of the AP-7131N-FGR 4.0 within Internet Explorer. Select the Continue to this Website (not recommended) option. The default IP address is 10.1.1.1. At this point in the browser configuration, a screen displays stating the Web site’s certificate cannot be verified. 5. Click Yes to continue. The access point’s login screen displays. 6. Log in using admin as the default User ID and motorola as the default password.
3-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide default IP address of 192.168.0.1. The default WAN IP address for GE2 port is set to 10.1.1.1. For this example, the access point’s LAN interface (GE1 port) will be used to connect to the access point.For optimal viewing of the Web UI, the screen resolution should be set to 1024 x 768 pixels or greater.
Getting Started 3. If the default login is successful, the Change Admin Password window displays. Change the 8-19 character password to ensure the AP-7131N-FGR is using a secure password different from the default password. Enter the current password and a new admin password in fields provided. Click Apply. Once the admin password has been updated, a warning message displays stating the access point must be set to a country.
3-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3.4.3 Configuring Device Settings Configure a set of minimum required device settings within the Quick Setup screen. The values (LAN, WAN etc.) can often be defined in other locations within the menu tree. When you change the settings in the Quick Setup screen, the values also change within the screen where these parameters also exist.
Getting Started 3. Refer to the AP-71xx System Settings field to define the following parameters: System Name Assign a System Name to define a title for this access point. The System Name is useful if multiple devices are being administered. Country Select the Country for the access point’s country of operation. The access point prompts for the correct country code on the first login. A warning message also displays stating an incorrect country setting may result in illegal radio operation.
3-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Time Server Optionally enter the IP address of the server used to provide system time to the access point within the Time Server field. Once the IP address is entered, the access point’s Network Time Protocol (NTP) functionality is engaged automatically.
Getting Started Sensor only Spectrum Analysis mode (no WLAN) Radio 1 WIPS, Radio 2 WIPS 2.4 GHz WLAN - no Sensor Radio1 WLAN, Radio 2 Disabled 5.0 GHz WLAN - no Sensor Radio1 Disabled, Radio 2 WLAN Radios Off Radios 1 and 2 Disabled 5. Select the Quick Setup screen’s Network Configuration tab to define a minimum set of WAN or LAN configuration values. The WAN tab displays by default. Set a minimum set of parameters for using the WAN interface. a.
3-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide option to effectively isolate the access point’s WAN connection. No connections to a larger network or the Internet will be possible. MUs cannot communicate beyond the configured subnets. b. Select the This Interface is a DHCP Client checkbox to enable DHCP for the access point’s WAN connection. This is useful, if the larger corporate network or Internet Service Provider (ISP) uses DHCP.
Getting Started j. Specify the Password entered when connecting to the ISP. When the Internet session starts, the ISP authenticates the password. For additional access point WAN port configuration options, see Configuring WAN Settings on page 5-16. 6. Select the LAN#1 tab to set a minimum set of parameters to use the LAN#1 interface. a. Select the Enable LAN Interface checkbox to forward data traffic over the access point’s LAN connection. The LAN connection is enabled by default. b.
3-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide still be assigned to another client. To avoid this, ensure all statically mapped IP addresses are outside of the IP address range assigned to the DHCP server. For additional access point LAN port configuration options, see Configuring the LAN Interface on page 5-1. 7. Select the WLAN #1 tab (WLANs 1 - 4 are available within the Quick Setup screen) to define its ESSID and security scheme for basic operation.
Getting Started 9. Click Apply to save any changes to the access point Quick Setup screen. Navigating away from the screen without clicking Apply results in all changes to the screens being lost. 10. Click Undo Changes (if necessary) to undo any changes made. Undo Changes reverts the settings displayed on the access point Quick Setup screen to the last saved configuration. 3.4.3.1 Configuring Basic WLAN Security Settings To configure a basic security policy for a WLAN: 1.
3-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. Configure the Key Rotation Settings as required to set Broadcast Key Rotation and the update interval. Broadcast Key Rotation Select the Broadcast Key Rotation checkbox to enable or disable broadcast key rotation. When enabled, the key indices used for encrypting/decrypting broadcast traffic will be alternatively rotated on every interval specified in the Broadcast Key Rotation Interval.
Getting Started 5. Configure the Key Settings as needed. 256-bit Key To use a hexadecimal value (and not an ASCII passphrase), select the checkbox and enter 16 hexadecimal characters into each of the four fields displayed. Default (hexadecimal) 256-bit keys for WP2A/CCMP include: 1011121314151617 18191A1B1C1D1E1F 2021222324252627 28292A2B2C2D2E2F 6. Configure the Fast Roaming (802.1x only) field as required to enable additional access point roaming and key caching options.
3-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide configure the parameters of the test. The WNMP ping test only works with Motorola Solutions MUs. Only use a Motorola Solutions MU to test access point connectivity using WNMP. NOTE Before testing for connectivity, the target MU needs to be set to the same ESSID as the access point. Since WPA2/CCMP has been configured for the access point, the MU also needs to be configured for WPA2/CCMP and use the same keys.
Getting Started • • • For detailed information on configuring access point LAN interface (subnet) and WAN interface see, Chapter 5, Network Management on page 5-1. For detailed information on configuring specific encryption and authentication security schemes for individual access point WLANs, see Chapter 6, Configuring Access Point Security on page 6-1. To view detailed statistics on the access point and its associated MUs, see Chapter 7, Monitoring Statistics on page 7-1.
3-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
System Configuration The access point contains a built-in browser interface for system configuration and remote management using a standard Web browser such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox (version 0.8 or higher is recommended). The browser interface also allows for system monitoring of the access point. Web management of the access point requires either Microsoft Internet Explorer 5.0 or later or Netscape Navigator 6.0 or later.
4-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide System configuration topics include: • • • • • • • • • • • Configuring System Settings Configuring Power Settings Adaptive AP Setup Configuring Data Access Managing Certificate Authority (CA) Certificates Configuring SNMP Settings Configuring Network Time Protocol (NTP) Logging Configuration Importing/Exporting Configurations Updating Device Firmware Key Zeroisation 4.
System Configuration 2. Configure the access point System Settings field to assign a system name and location, set the country of operation and view device version information. System Name Specify a device name for the access point. Motorola Solutions recommends selecting a name serving as a reminder of the user base the access point supports (engineering, retail, etc.).
4-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Country The access point prompts the user for the correct country code after the first login. A warning message also displays stating that an incorrect country setting will lead to an illegal use of the access point. Use the pull-down menu to select the country of operation. Selecting the correct country is extremely important.
System Configuration CAUTION Restoring the access point’s configuration back to default settings changes the administrative password back to “motorola.” If restoring the configuration back to default settings, be sure you change the administrative password accordingly. Restore Default Configuration Select the Restore Default Configuration button to reset the AP’s configuration to factory default settings.
4-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Restart Click the Restart button to reboot the AP-7131N-FGR. Restarting the AP-7131N-FGR resets all data collection values to zero. Motorola Solutions does not recommend restarting the AP-7131N-FGR during significant system uptime or data collection activities. CAUTION After a reboot, static route entries disappear from the AP Route Table if a LAN Interface is set to DHCP Client.
System Configuration • • • The access point’s transmit and receive algorithms could be negatively impacted The access point’s transmit power could be reduced due to insufficient power The access point’s WAN port configuration could be changed (either enabled or disabled) Automatic is the default mode. When Auto is selected, the CPLD determines how much power is available at startup (3af, 3at or Full Power for an AP-7131N-FGR model).
4-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Rates (Mbps) MCS Indices EVM Maximum Maximum Transmit Power Transmit Power Bandwidth 2.
System Configuration Rates (Mbps) MCS Indices EVM Maximum Maximum Transmit Power Transmit Power Bandwidth 2.4 GHz 5 GH 1 -9 20MHz 20 NA 2 -9 20MHz 20 NA 5.
4-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide To define the access point’s power setting: 1. Select System Configuration -> Power Settings from the menu tree. 2. Refer to the following to assess the access point’s current power state. Once known, determine how available power resources are applied to the access point’s radios. a NOTE Within the Power Settings field, an installation professional selects a power mode as auto or 3af.
System Configuration Power Mode When the access point is powered on for the first time, the system determines the power budget available to the access point. Using the Auto setting (default setting), the access point automatically determines the best power configuration based on the available power budget. If 3af is selected, the AP assumes 12.95 watts are available. If the mode is changed, the access point requires a reset to implement the change.
4-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide To configure the access point’s switch discovery method and connection medium: 1. Select System Configuration -> Adaptive AP Setup from the menu tree. 2. Define the following to prioritize a switch connection scheme and AP interface used to adopt to the switch. Control Port Define the port used by the switch FQDN to transmit and receive with the AAP. The default control port is 24576.
System Configuration Auto Discovery Enable When the Auto Discovery Enable checkbox is selected, the access point begins the switch discovery (adoption) process using DHCP first, then a user provided domain name, lastly using static IP addresses. This setting is disabled by default. When disabled, the AP functions as a standalone access point without trying to adopt a switch. Consequently, the access point will not be able to obtain an AAP configuration.
4-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6. Click Logout to securely exit the access point Access Point applet. A prompt displays confirming the logout before the applet is closed. 4.4 Configuring Data Access Use the Access screen to allow/deny management access to the access point from different subnets (LAN1, LAN2 or WAN) using different protocols such as HTTPS, SSH2 or SNMP. The access options are either enabled or disabled.
System Configuration 2. Use the access point Access field checkboxes to enable/disable the following on the access point’s LAN1, LAN2 or WAN interfaces: Applet HTTPS (port 443) Select the LAN1, LAN2 and/or WAN checkboxes to enable access to the access point configuration applet using a Secure Sockets Layer (SSL) for encrypted HTTP sessions. CLI SSH2 (port 22) Select the LAN1, LAN2 and/or WAN checkboxes to enable access to the access point CLI using the SSH (Secure Shell) protocol.
4-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. Configure the Secure Shell field to set timeout values to reduce network inactivity. Authentication Timeout Defines the maximum time (between 30 - 120 seconds) allowed for SSH authentication to occur before executing a timeout. The minimum permissible value is 30 seconds. SSH Inactivity Timeout Terminates the SSH session to the access point if no data activity is detected over the session after the user defined interval.
System Configuration Port Specify the port on which the server is listening. The RADIUS server typically listens on ports 1812 (default port). Shared Secret Define a shared secret for authentication on the server. The shared secret is required to be the same as the shared secret defined on the RADIUS server. Use shared secrets to verify RADIUS messages (with the exception of the Access-Request message) sent by a Radius-enabled device configured with the same shared secret.
4-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 9. Click Apply to save any changes to the access point Access screen. Navigating away from the screen without clicking the Apply button results in all changes to the screen being lost. 10. Click Undo Changes (if necessary) to undo any changes made. Undo Changes reverts the settings displayed on the access point Access screen to the last saved configuration. 11. Click Logout to securely exit the access point Access Point applet.
System Configuration certificate. A browser must contain this CA certificate in its Trusted Root Library so it can trust certificates “signed” by the CA's private key. Depending on the public key infrastructure, the digital certificate includes the owner's public key, the certificate expiration date, the owner's name and other public key owner information. . CAUTION Loaded and signed CA certificates will be lost when changing the access point’s firmware version using either the GUI or CLI.
4-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Copy the content of the CA Certificate message (using a text editor such as Notepad) and click on Paste from Clipboard. Note that this feature will work with Internet Explorer browser only. The content of the certificate displays in the Import a root CA Certificate field. 3. Click the Import root CA Certificate button to import it into the CA Certificate list. 4.
System Configuration CAUTION Self certificates can only be generated using the access point GUI and CLI interfaces. No functionality exists for creating a self-certificate using the access point’s SNMP configuration option. To create a self certificate: 1. Select System Configuration -> Certificate Mgmt -> Self Certificates from the access point menu tree. 2. Click on the Add button to create the certificate request. The Certificate Request screen displays. 3.
4-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Key ID Enter a logical name for the certificate to help distinguish between certificates. The name can be up to 7 characters in length. Subject The required Subject value contains important information about the certificate. Contact the CA signing the certificate to determine the content of the Subject parameter.
System Configuration The generated certificate request displays in Self Certificates screen text box. 6. Click the Copy to Clipboard button (Note that this feature will work with Internet Explorer browser version 6 and above only). The content of certificate request is copied to the clipboard. Create an e-mail to your CA, paste the content of the request into the body of the message and send it to the CA. The CA signs the certificate and will send it back.
4-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE If the access point is restarted after a certificate request has been generated but before the signed certificate is imported, the import will not execute properly. Do not restart the access point during this process. 4.5.3 Creating a Certificate for Onboard RADIUS Authentication The access point can use its on-board RADIUS Server loaded with certificates to authenticate MUs. AP can generate certificate request.
System Configuration Subject (required) The required Subject value contains important information about the certificate. Contact the CA signing the certificate to determine the content of the Subject parameter. Department Optionally enter a value for your organizations’s department name if needing to differentiate the certificate from similar certificates used in other departments within your organization.
4-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The Certificate Request screen disappears and the ID of the generated certificate request displays in the drop-down list of certificates within the Self Certificates screen. NOTE A Warning screen may display at this phase stating key information could be lost if you proceed with the certificate request. Click the OK button to continue, as the certificate has not been signed yet. 6.
System Configuration CAUTION Ensure the CA Certificate is loaded before the Self Certificate, or risk an invalid certificate load. 16. Open the certificate file and copy its contents into the CA Certificates screen by clicking the Paste from Clipboard button. (Note that this feature will work with Internet Explorer browser version 6 and above only.) The certificate is now ready to be loaded into the access point’s flash memory. 17.
4-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Use Symbol-AP_MIB to configure the below features Feature MIB Reference LAN Configuration apLan VLAN Configuration apLanVlan 802.
System Configuration Firewall Configuration ccWanFirewall Router Configuration ccRouter System Settings ccAdmin NTP Server Configuration ccNtp Logging Configuration ccLogging Firmware Update ccLoadFw Wireless Stats ccWlan Radio Stats ccPortal MU Stats ccMuStats Config Import/Export ccLoadCfg Few acronyms used in the MIB files: Portal Radio of an AP MIB Management Information Base LAN Local Area Network WAN Wide Area Network POE Power Over Ethernet WLAN Wireless LAN AP Acces
4-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide SNMP v3 user definitions work independently, and both use the Access Control List (ACL) of the SNMP Access Control sub-screen. Use the SNMP Access screen to define SNMP community definitions and SNMP v3 user definitions. SNMP version 3 (v3) further enhances protocol features, providing much improved security. SNMP v3 encrypts transmissions and provides authentication for users generating requests.
System Configuration Username Specify a username by typing an alphanumeric string of up to 31 characters. Security Level Use the Security Level area to specify a security level of AuthPriv (authorization with privacy). The AuthPriv setting requires login authorization and uses the Advanced Encryption Standard (AES) protocol. OID Use the OID (Object Identifier) area to specify a setting of All or enter a Custom OID. Select All to assign the user access to all OIDs in the MIB.
4-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide SNMP v3 Engine ID The access point SNMP v3 Engine ID field lists the unique SNMP v3 Engine ID for the access point. This ID is used in SNMP v3 as the source for a trap, response or report. It is also used as the destination ID when sending get, getnext, getbulk, set or inform commands. 5. Click Apply to save any changes to the SNMP Access screen.
System Configuration 4.6.1 Configuring SNMP Access Control Use the SNMP Access Control screen (as launched from the SNMP Access screen) to specify which users can read SNMP generated information and, if capable, modify related settings from an SNMP-capable client. Use the SNMP Access Control screen's Access Control List (ACL) to limit, by Internet Protocol (IP) address, who can access the access point SNMP interface.
4-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Access Control List Enter Start IP and End IP addresses (numerical addresses only, no DNS names supported) to specify a range of user that can access the access point SNMP interface. An SNMP-capable client can be set up whereby only the administrator (for example) can use a read/ write community definition. Use just the Starting IP Address column to specify a SNMP user.
System Configuration 1. Select System Configuration - > SNMP Access - > SNMP Trap Configuration from the access point menu tree. CAUTION Ensure IPSec has been properly configured to protect communications with the external SNMP server. Changes will not be applied otherwise. 2. Configure the SNMP v3 Trap Configuration field (if SNMP v3 Traps are used) to modify the following: Add Click Add to create a new SNMP v3 Trap Configuration entry. Delete Select Delete to remove an entry for an SNMP v3 user.
4-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Username Enter a username specific to the SNMP-capable client receiving the traps. Security Level Use the Security Level drop-down menu to specify security level as AuthPriv (authorization with privacy). The “AuthPriv” setting requires login authorization and uses the Advanced Encryption Standard (AES).
System Configuration 2. Configure the MU Traps field to generate traps for MU associations, MU association denials and MU authentication denials. When a trap is enabled, a trap is sent every 10 seconds until the condition no longer exists. MU associated Generates a trap when an MU becomes associated with one of the access point’s WLANs. MU unassociated Generates a trap when an MU becomes unassociated with (or gets dropped from) one of the access point’s WLANs.
4-38 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Configure the SNMP Traps field to generate traps when SNMP capable MUs are denied authentication privileges or are subject of an ACL violation. When a trap is enabled, a trap is sent every 5 seconds until the condition no longer exists. SNMP authentication Generates a trap when an SNMP-capable client is denied access failures to the access point’s SNMP management functions or data.
System Configuration System Cold Start Generates a trap when the access point re-initializes while transmitting, possibly altering the SNMP agent's configuration or protocol entity implementation. Configuration Changes Generates a trap whenever changes to the access point’s configuration file are saved. Rogue AP Detection Generates a trap if a Rogue AP is detected by the access point. AP Radar Detection Generates a trap if an AP is detected using a form of radar detection.
4-40 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION Ensure IPSec has been properly configured to protect communications with the external SNMP server. Changes will not be applied otherwise. 2. Configure the RF Trap Thresholds field to define device threshold values for SNMP traps. NOTE Average Bit Speed,% of Non-Unicast, Average Signal, Average Retries,% Dropped and% Undecryptable are not access point statistics.
System Configuration Average Signal Enter a minimum threshold for the average signal strength in dBm for each device. Average Retries Set a maximum threshold for the average number of retries for each device. % Dropped Enter a maximum threshold for the total percentage of packets dropped for each device. Dropped packets can be caused by poor RF signal or interference on the channel. % Undecryptable Define a maximum threshold for the total percentage of packets undecryptable for each device.
4-42 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Time synchronization is recommended for the access point’s network operations. Use the Date and Time Settings screen to enable NTP and specify the IP addresses and ports of available NTP servers. NOTE The current time is not set accurately when initially connecting to the access point.
System Configuration 2. From within the Current Time field, click the Refresh button to update the time since the screen was displayed by the user. The Current Time field displays the current time based on the access point system clock. If NTP is disabled or if there are no servers available, the system time displays the access point uptime starting at 1970-01-01 00:00:00, with the time and date advancing. 3. Select the Set Date/Time button to display the Manual Date/Time Setting screen.
4-44 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION If using the RADIUS time-based authentication feature to authenticate access point user permissions, ensure UTC has been selected from the Time Zone field. If UTC is not selected, time based authentication will not work properly. For information on configuring RADIUS time-based authentication, see Defining User Access Permissions by Group on page 6-67. 5.
System Configuration 4.8 Logging Configuration The access point provides the capability for periodically logging system events that prove useful in assessing the throughput and performance of the access point or troubleshooting problems on the access point managed Local Area Network (LAN). Use the Logging Configuration screen to set the desired logging level (standard syslog levels) and view or save the current access point system log. To configure event logging for the access point: 1.
4-46 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide View Log Click View to save a log of events retained on the access point. The system displays a prompt requesting the administrator password before saving the log. After the password has been entered, click Get File to display a dialogue with buttons to Open or Save the log.txt file. Click Save and specify a location to save the log file. Use the WordPad application to view the saved log.
System Configuration 3. Configure the Audit Log Filters field to create or delete audit log filters. Create Click Create to create a new audit log filter. The Create Audit Log Filter window is displayed. Provide the relevant information and click Apply to save the changes. Unset Click Unset to remove a selected audit log filter Unset All Click Unset All to delete all audit filter logs. 4. Click Apply to save any changes to the Logging Configuration screen.
4-48 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The export function always exports the encrypted Admin User password. The import function imports the Admin Password only if the access point is set to factory default. If the access point is not configured to factory default settings, the Admin User password WILL NOT get imported. A configuration file from a dual radio AP-7131N-FGR can be imported to another dual radio model AP-7131N-FGR.
System Configuration 3. Configure the SFTP Import/Export field to import/export configuration settings. Filename Specify the name of the configuration file to be written to the SFTP Server. SFTP Server IP Enter the numerical (non-DNS name) IP address of the destination SFTP Server where the configReuration file is imported or exported. Filepath (optional) Defines the optional path name used to import/export the target configuration file.
4-50 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Export Configuration Click the Export Configuration button to export the configuration file from the server with the assigned filename and login information. If the IP mode is set to DHCP Client, IP address information is not exported (true for both LAN1, LAN2 and the WAN port). For LAN1 and LAN2, IP address information is only exported when the IP mode is set to either static or DHCP Server.
System Configuration 4.10 Updating Device Firmware Motorola Solutions periodically releases updated versions of the access point device firmware to the Motorola Solutions Web site. If the access point firmware version displayed on the System Settings page (see Configuring System Settings on page 4-2) is older than the version on the Web site, Motorola Solutions recommends updating the access point to the latest firmware version for full feature functionality.
4-52 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The firmware file must be available from a SFTP site to perform the update. CAUTION Make sure a copy of the access point’s configuration is exported before updating the firmware. To conduct a firmware update on the access point: 1. Export the access point current configuration settings before updating the firmware to have the most recent settings available after the firmware is updated.
System Configuration If updating the access point manually, configure the Update Firmware fields as required to set a filename and target firmware file upload location for firmware updates. 3. Specify the name of the target firmware file within the Filename field. 4. If the target firmware file resides within a directory, specify a complete path for the file within the Filepath(optional) field. 5. Enter an IP address for the SFTP server used for the update.
4-54 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The access point must complete the reboot process to successfully update the device firmware, regardless of whether the reboot is conducted using the GUI or CLI interfaces. 8. Confirm the access point configuration is the same as it was before the firmware update. If they are not, restore the settings.
System Configuration 4.11.
4-56 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 7 Remove secret and configuration files • • • • • • • • Admin password RADIUS client configuration file EAP configuration file RADIUS CA certificate RADIUS client certificate RADIUS client password file HTTPS certificate Image Verification Keys file 8 Restore factory default configuration Restore factory default configuration 9 Reboot the AP Reboot the AP
Network Management Refer to the following for network management configuration activities supported by the access point user interface: • • • • • Configuring the LAN Interface Configuring WAN Settings Enabling Wireless LANs (WLANs) Configuring Router Settings Configuring IP Filtering 5.1 Configuring the LAN Interface The AP-7131N-FGR has one physical LAN port supporting two unique LAN interfaces. The AP-7131N-FGR LAN port has its own MAC address.
5-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide For information on locating the access point’s MAC addresses, see Viewing WAN Statistics on page 7-2 and Viewing LAN Statistics on page 7-6.
Network Management Enable Select the LAN1 and/or LAN2 checkbox to allow the forwarding of data traffic over the specified LAN connection. The LAN1 connection is enabled by default, but both LAN interfaces can be enabled simultaneously. The LAN2 setting is disabled by default. LAN Name Use the LAN Name field to modify the existing LAN name. LAN1 and LAN2 are the default names assigned to the LANs until modified by the user.
5-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The access point only supports 802.1x authentication over its LAN port. The access point behaves as an 802.1x supplicant to authenticate to a server on the network. If using 802.1x authentication, enter the authentication server user name and password. The default password is “motorola.
Network Management full duplex Select this option to transmit data to and from the access point at the same time. Using full duplex, the access point can send data over its LAN port while receiving data as well. 6. Click Apply to save any changes to the LAN Configuration screen. Navigating away from the screen without clicking the Apply button results in all changes to the screen being lost if the prompts are ignored. 7. Click Undo Changes (if necessary) to undo any changes made.
5-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Although static VLANs are the most common form of VLAN assignments, dynamic VLAN assignment is possible per WLAN. Configuring dynamic VLANs entail the access point sending a DHCP request for device information (such as an IP address). Additional information (such as device MAC address information) is sent to the access point. The access point sends this MAC address to a host housing a copy of the Dynamic VLAN database.
Network Management The VLAN name screen displays. The first time the screen is launched a default VLAN name of 1 and a default VLAN ID of 1 display. The VLAN name is auto-generated once the user assigns a VLAN ID. However, the user has the option of re-assigning a name to the VLAN using New VLAN and Edit VLAN screens. To create a new VLAN, click the Add button, to edit the properties of an existing VLAN, click the Edit button. 4. Assign a unique VLAN ID (from 1 to 4095) to each VLAN added or modified.
5-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide connectivity, but it requires VLAN numbering be managed carefully to avoid conflicts between two VLANs with the same ID. 5. Define a 32 character maximum VLAN Name. Enter a unique name that identifies members of the VLAN. Motorola recommends selecting the name carefully, as the VLAN name should signify a group of clients with a common set of requirements independent of their physical location. 6.
Network Management 5.1.2 Configuring LAN1 and LAN2 Settings Both LAN1 and LAN2 have separate sub-screens to configure the DHCP settings used by the LAN1 and LAN2 interfaces. Within each LAN screen is a button to access a sub-screen to configure advanced DHCP settings for that LAN. For more information, see Configuring Advanced DHCP Server Settings on page 5-13.
5-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Configure the DHCP Configuration field to define the DHCP settings used for the LAN. NOTE When setting the LAN interface to be a DHCP Server and adding an IP address, the primary DNS IP address might not be updated, with only the secondary address getting updated. Ensure the primary address is the same as the IP address of the LAN. NOTE Motorola recommends the WAN and LAN ports should not both be configured as DHCP clients.
Network Management Address Assignment Range Use the address assignment parameter to specify a range of numerical (non DNS name) IP addresses reserved for mapping client MAC addresses to IP addresses. If a manually (static) mapped IP address is within the IP address range specified, that IP address could still be assigned to another client. To avoid this, ensure all statically mapped IP addresses are outside of the IP address range assigned to the DHCP server.
5-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Mesh STP Configuration Click the Mesh STP Configuration button to define bridge settings for this specific LAN. Each of the access point’s two LANs can have a separate mesh configuration. As the Spanning Tree Protocol (STP) mentions, each mesh network maintains hello, forward delay and max age timers. These settings can be used as is using the current default settings, or be modified.
Network Management 5.1.2.1 Configuring Advanced DHCP Server Settings Use the Advanced DHCP Server screen to specify (reserve) static (or fixed) IP addresses for specific devices. Every wireless, 802.11x-standard device has a unique Media Access Control (MAC) address. This address is the device's hard-coded hardware number (shown on the bottom or back). An example of a MAC address is 00:A0:F8:45:9B:07. The DHCP server can grant an IP address for as long as it remains in active use.
5-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Specify a lease period in seconds for available IP addresses using the DHCP Lease Time (Seconds) parameter. An IP address is reserved for re-connection for the length of time you specify. The default interval is 86400 seconds. 4. Click the Add button to create a new table entry within the Reserved Clients field.
Network Management 2. Use the all ethernet types, except drop-down menu to designate whether the Ethernet Types defined for the LAN are allowed or denied for use by the access point. 3. To add an Ethernet type, click the Add button. The Add Ethernet Type screen displays. Use this screen to add one type filter option at a time, for a list of up to 16 entries.
5-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Packet types supported for the type filtering function include 16-bit DIX Ethernet types as well as Motorola proprietary types. Select an Ethernet type from the drop down menu, or enter the Ethernet type’s hexadecimal value. See your System Administrator if unsure of the implication of adding or omitting a type from the list for either LAN1 or LAN2. 4.
Network Management 2. Refer to the WAN IP Configuration field to enable the WAN interface, and set network address information for the WAN connection. NOTE Motorola recommends that the WAN and LAN ports should not both be configured as DHCP clients. Enable WAN Interface Select the Enable WAN Interface checkbox to enable a connection between the access point and a larger network or outside world through the WAN port. Disable this option to effectively isolate the access point’s WAN.
5-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide This interface is a DHCP Client This checkbox enables DHCP for the access point WAN connection. This is useful, if the larger corporate network or Internet Service Provider (ISP) uses DHCP. DHCP is a protocol that includes mechanisms for IP address allocation and delivery of host-specific configuration parameters from a DHCP server to a host. Some of these parameters are IP address, network mask, and gateway.
Network Management More IP Addresses Click the More IP Addresses button to specify additional static IP addresses for the access point. Additional IP addresses are required when users within the WAN need dedicated IP addresses, or when servers need to be accessed (addressed) by the outside world. The More IP Addresses screen allows the administrator to enter up to seven additional WAN IP addresses for the access point WAN. Only numeric, non-DNS names can be used.
5-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide half duplex Select this option to transmit data to and from the access point, but not at the same time. Using a half duplex transmission, the access point can send data over its WAN port then immediately receive data from the same direction in which the data was transmitted. Like a full-duplex transmission, a half-duplex transmission can carry data in both directions, just not at the same time.
Network Management Keep-Alive Select the Keep-Alive checkbox to maintain the WAN connection indefinitely (no timeout interval). Some ISPs terminate inactive connections. Enabling Keep-Alive keeps the access point’s WAN connection active, even when there is no traffic. If the ISP drops the connection after an idle period, the access point automatically reestablishes the connection to the ISP. Enabling Keep-Alive mode disables (grays out) the Idle Time field.
5-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5.2.1 Configuring Network Address Translation (NAT) Settings Network Address Translation (NAT) converts an IP address in one network to a different IP address or set of IP addresses in another network. The access point router maps its local (inside) network addresses to WAN (outside) IP addresses, and translates the WAN IP addresses on incoming packets to local IP addresses.
Network Management Outbound Mappings When 1 to 1 NAT is selected, a single IP address can be entered in the Outbound Mappings area. This address provides a 1 to 1 mapping of the WAN IP address to the specified IP address. When 1 to Many is selected as the NAT Type, the Outbound Mappings area displays a 1 to Many Mappings button. Click the button to select the LAN1 or LAN2 IP address used to set the outbound IP address or select none to exclude the IP address.
5-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. Configure the Port Forwarding screen to modify the following: Add Click Add to create a local map that includes the name, transport protocol, start port, end port, IP address and Translation Port for incoming packets. Del Click Delto remove a selected local map entry. Name Enter a name for the service being forwarded. The name can be any alphanumeric string and is used for identification of the service.
Network Management IP Address Enter the numerical (non DNS name) IP address to which the specified service is forwarded. This address must be within the specified NAT range for the associated WAN IP address. Translation Port Specify the port number used to translate data for the service being forwarded. Forward all unspecified ports to Use the Forward all unspecified ports to checkbox to enable port forwarding for incoming packets with unspecified ports.
5-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The username, password and hostname are required to be registered at http://www.dyndns.com. 3. 4. 5. 6. Enter the DynDNS Username for the account you wish to use for the access point. Enter the DynDNS Password for the account you wish to use for the access point. Provide the Hostname for the DynDNS account you wish to use for the access point.
Network Management If a WLAN is defined, that WLAN displays within the Wireless Configuration screen. When the access point is first booted, WLAN1 exists as a default WLAN available immediately for connection. 2. Refer to the information within the Wireless Configuration screen to view the name, ESSID, access point radio designation, VLAN ID and security policy of existing WLANs. WLAN Name The Name field displays the name of each WLAN that has been defined.
5-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Radio The Radio field displays the name of the access point radio the WLAN is mapped to (either the 802.11a/n radio or the 802.11b/g/n radio). To change the radio designation for a specific WLAN, see Creating/Editing Individual WLANs on page 5-29. VLAN The VLAN field displays the specific VLAN the target WLAN is mapped to. For information on VLAN configuration for the WLAN, see Configuring VLAN Support on page 5-5.
Network Management 5.3.1 Creating/Editing Individual WLANs If the WLANs displayed within the Wireless Configuration screen do not satisfy your network requirements, you can either create a new WLAN or edit the properties of an existing WLAN. NOTE Before editing the properties of an existing WLAN, ensure it is not being used by an access point radio, or is a WLAN that is needed in its current configuration. Once updated, the previous configuration is not available unless saved.
5-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Set the parameters in the Configuration field as required for the WLAN. CAUTION When using the access point’s hotspot functionality, ensure MUs are re-authenticated when changes are made to the characteristics of a hotspot enabled WLAN, as MUs within the WLAN will be dropped from device association.
Network Management ESSID Enter the Extended Services Set Identification (ESSID) associated with the WLAN. The WLAN name is auto-generated using the ESSID until changed by the user. The maximum number of characters that can be used for the ESSID is 32. Do not use any of the following characters for an ESSID < > | " & \ ? , Name Define or revise the name for the WLAN. The name should be logical representation of WLAN coverage area (engineering, marketing etc.).
5-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Enable Client Bridge Backhaul Select the Enable Client Bridge Backhaul checkbox to make the WLAN available in the WLAN drop-down menu within the Radio Configuration screen. This checkbox can be ignored for WLANs not supporting mesh networking, to purposely exclude them from the list of WLANs available in the Radio Configuration page selected specifically for mesh networking support.
Network Management Disallow MU to MU Communication The MU-MU Disallow feature prohibits MUs from communicating with each other even if they are on different WLANs, assuming one of the WLAN’s is configured to disallow MU-MU communication. Therefore, if an MU’s WLAN is configured for MU-MU disallow, it will not be able to communicate with any other MUs connected to this access point. Use Secure Beacon Select the Use Secure Beacon checkbox to not transmit the access point’s ESSID.
5-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide IP Filtering Select the IP Filtering button to display a screen where existing IP filter policies can be applied to the WLAN to allow or deny IP packets in either an incoming or outgoing direction based on the rules defined for the policy. NOTE For an overview of IP Filtering and how to create a filter, see Configuring IP Filtering on page 5-73.
Network Management NOTE When the access point is first launched, a single security policy (default) is available and mapped to WLAN 1. It is anticipated numerous additional security policies will be created as the list of WLANs grows. Configuring a WLAN security scheme with a discussion of all the authentication and encryption options available is beyond the scope of this chapter. See Chapter 6, Configuring Access Point Security on page 6-1 for more details on configuring access point security.
5-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide point connectivity. Use the Mobile Unit Access Control List Configuration screen to create new ACL policies (using the New MU ACL Policy sub-screen) or edit existing policies (using the Edit MU ACL Policy sub-screen). Once new policies are defined, they are available for use within the New WLAN or Edit WLAN screens to assign to specific WLANs based on MU interoperability requirements.
Network Management 2. Click the Create button to configure a new ACL policy, or select a policy and click the Edit button to modify an existing ACL policy. The access point supports a maximum of 16 MU ACL policies.
5-38 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Either the New MU ACL Policy or Edit MU ACL Policy screens display. 3. Assign a name to the new or edited ACL policy that represents an inclusion or exclusion policy specific to a particular type of MU traffic you may want to use with a single or group of WLANs. More than one WLAN can use the same ACL policy. 4. Configure the parameters within the Mobile Unit Access Control List field to allow or deny MU access to the access point.
Network Management Add Click the Add button to create a new entry using only the Start MAC column to specify a MAC address, or uses both the Start MAC and End MAC columns to specify a range of MAC addresses. Delete Click the Delete button to remove a selected list entry. 5. Click Apply to save any changes to the New MU ACL Policy or Edit MU ACL Policy screen and return to the Mobile Unit Access Control List Configuration screen.
5-40 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE When the access point is first launched, a single QoS policy (default) is available and mapped to WLAN 1. It is anticipated additional QoS policies will be created as the list of WLANs grows. 2. Click the Create button to configure a new QoS policy, or select a policy and click the Edit button to modify an existing QoS policy. The access point supports a maximum of 16 QoS policies.
Network Management 3. Assign a name to the new or edited QoS policy that makes sense to the access point traffic receiving priority. More than one WLAN can use the same QoS policy. 4. Select the Support Voice prioritization checkbox to allow legacy voice prioritization. Certain products may not receive priority over other voice or data traffic.
5-42 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE Wi-fi functionality requires both the access point and its associated clients are WMM-capable and have WMM enabled. WMM enabled devices can take advantage of their QoS functionality only if using applications that support WMM, and can assign an appropriate priority level to the traffic streams they generate. 5. Use the two Multicast Address fields to specify one or two MAC addresses used for multicast applications.
Network Management 7. Select the Enable Wi-Fi Multimedia (WMM) QoS Extensions checkbox to configure the access point’s QoS Access Categories. The Access Categories are not configurable unless the checkbox is selected. Access Categories include: Background Backgrounds traffic is typically of a low priority (file transfers, print jobs ect.). Background traffic typically does not have strict latency (arrival) and throughput requirements.
5-44 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide TXOPs Time 32usec The TXOPs Time is the interval the transmitting MU is assigned for transmitting. The default for Background traffic is 0. The same TXOPs values should be used for either the 802.11a/n or 802.11b/g/n radio, there is no difference. TXOPs Time ms TXOP times range from 0.2 ms (background priority) to 3 ms (video priority) in a 802.11a/n network, and from 1.2 ms to 6 ms in an 802.11b/g/n network.
Network Management 5.3.1.4 Configuring WLAN Hotspot Support The access point enables hotspot operators to provide user authentication and accounting without a special client application. The access point uses a traditional Internet browser as a secure authentication device. The access point issues an IP address to the user using a DHCP server, authenticates the user and grants the user to access the Internet.
5-46 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Refer to the HTTP Redirection field to specify how the Login, Welcome, and Fail pages are maintained for this specific WLAN. The pages can be hosted locally or remotely. . Use Default Files Select the Use Default Files checkbox if the login, welcome and fail pages reside on the access point.
Network Management Use External URL Select the Use External URL checkbox to define a set of external URLs for hotspot users to access the login, welcome and fail pages. To create a redirected page, you need to have a TCP termination locally. On receiving the user credentials from the login page, the access point connects to a radius server, determines the identity of the connected wireless user and allows the user to access the Internet based on successful authentication. 4.
5-48 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The Enable Hotspot User Timeout option is only available if using the access point’s internal Radius Server for user authentication. 6. Click the White List Entries button (within the WhiteList Configuration field) to create a set of allowed destination IP addresses. These allowed destination IP addresses are called a White List. Ten configurable IP addresses are allowed for each WLAN.
Network Management 8. Refer to the Radius Configuration field to define a primary and secondary Radius server port and shared secret password. Select mode Use the Select mode drop-down menu to define whether an Internal or External server is to be used for the primary server. Pri Server IP Define the IP address of the primary Radius server. This is the address of your first choice for Radius server. Pri Port Enter the TCP/IP port number for the server acting as the primary Radius server.
5-50 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide When a client requests a URL from a Web server, the login handler returns an HTTP redirection status code (for example, 301 Moved Permanently), which indicates to the browser it should look for the page at another URL. This other URL can be a local or remote login page (based on the hotspot configuration). The login page URL is specified in the location’s HTTP header.
Network Management 5.3.2 Setting the WLAN’s Radio Configuration Each AP-7131N-FGR WLAN can have a separate 802.11a/n or 802.11b/g/n radio configured and mapped to that WLAN. This enables each WLAN to optimize its radio configuration in respect to its intended client needs. With dual-radio model AP-7131N-FGR access points, the Radio Configuration screen enables you to configure one radio for 802.11a (or a/n) use and the other for 802.11b/g (or b/g/n) support.
5-52 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • Live View- The WIPS application (commonly referred to as Motorola Enterprise) provides a live view of the sensors, APs and MUs operating in a WLAN. Live view support exists throughout the WIPS application, wherever a device icon appears in an information panel or navigation tree. Access Live View by right-clicking on the device, which automatically limits the data to the specific device your choose.
Network Management Refer to RF Band of Operation parameter to ensure you are enabling the correct radio. After the settings are applied within this Radio Configuration screen, the Radio Status and MUs connected values update. If this is an existing radio within a mesh network, these values update in real-time. NOTE This section describes mesh networking (setting the radio’s base and client bridge configuration) at a high level.
5-54 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide within the CBs Connected field. If this is an existing radio within a mesh network, this value updates in real-time. CAUTION A problem could arise if a Base Bridge’s Indoor channel is not available on an Outdoor Client Bridge's list of available channels. As long as an Outdoor Client Bridge has the Indoor Base Bridge channel in its available list of channels, it can associate to the Base Bridge. 5.
Network Management Disabled When disabled, both radios are up at boot time and beaconing. If one radio (radio 1) does not have a mesh connection, the other radio (radio 2) is not affected. Radio 2 continues to beacon and associate MUs, but MU's can only communicate amongst themselves using the access point. Disabled is the default value. Uplink Detect When Uplink Detect is selected, the access point only boots up the radio configured as a client bridge.
5-56 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION When defining a Mesh configuration and changes are saved, the mesh network temporarily goes down. The Mesh network is unavailable because the access point radio is reconfigured when applying changes. This can be problematic for users making changes within a deployed mesh network. If updating the mesh network using a LAN connection, the access point applet loses connection and the connection must be re-instated.
Network Management 2. Configure the Properties field to assign a name and placement designation for the radio. Placement Use the Placement drop-down menu to specify whether the radio is located outdoors or indoors. Default placement depends on the country of operation selected for the access point. MAC Address The access point, like other Ethernet devices, has a unique, hardware encoded Media Access Control (MAC) or IEEE address. MAC addresses determine the device sending or receiving data.
5-58 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide ERP Protection Extended Rate PHY (ERP) allows 802.11g MUs to interoperate with 802.11b only MUs. ERP Protection is managed automatically by the access point and informs users when 802.11b MUs are present within the access point’s coverage area. The presence of 802.11b MUs within the 802.
Network Management Channel Width Select the Channel Width (MHz) from the drop-down menu. The AP radio can support 20 and 40 MHz channel widths. 20 MHz is the default setting for the 2.4 GHz radio. 20/40 MHz operation (the default setting for the 5 GHz radio) allows the access point to receive packets from clients using 20 MHz of bandwidth while transmitting a packet using 40 MHz bandwidth. This mode is supported for 11n users on both the 2.4 and 5 GHz radios.
5-60 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Set Rates Click the Set Rates button to define minimum and maximum data transmit rates for the radio. Use the Basic Rates drop-down menu to select the rates available for either the 2.4 GHz or 5 GHz radio band. The menu options differ, based on the radio band. For 2.4 GHz, the following options are available: • 1 and 2 Mbps • 1, 2, 5.5 and 11 Mbps (default setting) • 1, 2, 5.5, 11 and 6, 12, 24 Mbps • 1, 2, 5.
Network Management 4. Configure the Performance field to set the preamble, thresholds values and QoS values for the radio.
5-62 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Support Short Preamble The preamble is approximately 8 bytes of packet header generated by the access point and attached to a packet prior to transmission from the 802.11b radio. The preamble length for 802.11b transmissions is rate dependant. A short preamble is 50% shorter than a long preamble.
Network Management Set Aggregation Select the Enable Transmit A-MSDU checkbox (within the A-MSDU Aggregation field) to enable the aggregation of MAC Service frames. When enabled, long frames can be both sent and received (up to 4 KB). The A-MSDU buffer limit is not user configurable. If disabled, no AMSDU packets are transmitted by the access point. Select the Enable Transmit A-MPDU checkbox (within the A-MPDU Aggregation field) to allow the aggregation of MAC Protocol frames.
5-64 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5. Refer to the Beacon Settings field to set the radio beacon and DTIM intervals. Beacon Interval The beacon interval controls the performance of power save stations. A small interval may make power save stations more responsive, but it will also cause them to consume more battery power. A large interval makes power save stations less responsive, but could increase power savings. The default is 100.
Network Management 6. Refer to the QBSS Load Element Settings field to determine whether channel usage data is transmitted to associated devices. Enable QBSS load element When enabled, the access point communicates channel usage data to associated devices using an interval you define. The QBSS load represents the percentage of time the channel is in use by the access point and the access point’s MU count.
5-66 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide be defined from within the WLANs assigned to BSSID groups 1 through 4. Each BSSID beacons only on the primary WLAN. The user should assign each WLAN to its own BSSID. In cases where more than four WLANs are required, WLANs should be grouped according to their security policies so all of the WLANs on a BSSID have the same security policy.
Network Management 11. Click Logout to securely exit the Access Point applet. A prompt displays confirming the logout before the applet is closed. 5.3.3 Configuring MU Rate Limiting Use the Rate Limiting screen to control the MU rate limit allotted to individual WLANs. MU rate limiting enables an administrator to determine how much radio bandwidth is allowed to each MU within any one of the 16 supported AP WLANs. To define MU rate limits for specific WLANs on an access point radio: 1.
5-68 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Once enabled, MU rate limiting still needs to be enabled for a specific WLAN, then the rate limit allocation needs to be defined for MU traffic within that specific WLAN. To modify a WLAN-to-radio assignment, see Creating/Editing Individual WLANs on page 5-29. 3. Refer to the Per WLAN Rate Limits field to review the rate limits defined thus far for any of the access point’s 16 WLANs.
Network Management 2. Refer to the access point Router Table field to view existing routes. The access point Router Table field displays a list of connected routes between an enabled subnet and the router. These routes can be changed by modifying the IP address and subnet masks of the enabled subnets. The information in the access point Router Table is dynamically generated from settings applied on the WAN screen. The destination for each subnet is its IP address.
5-70 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide select the type of RIP and the type of RIP authentication used by the switch. For more information on configuring RIP, see Setting the RIP Configuration on page 5-71. 5. Use the User Defined Routes field to add or delete static routes. The User Defined Routes field allows the administrator to view, add or delete internal static (dedicated) routes. a. Click the Add button to create a new table entry. b.
Network Management 5.4.1 Setting the RIP Configuration To set the RIP configuration: 1. From within the RIP Configuration field, select the RIP Type from the drop-down menu. The following options are available: No RIP The No RIP option prevents the access point’s router from exchanging routing information with other routers. Routing information may not be appropriate to share, for example, if the access point manages a private LAN. RIP v1 RIP version 1 is a mature, stable, and widely supported protocol.
5-72 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. If RIP v2 or RIP v2 (v1 compat) is the selected RIP type, the RIP v2 Authentication field becomes active. Select the type of authentication to use from the Authentication Type drop-down menu. Available options include: None This option disables the RIP authentication. Simple This option enable RIP version 2’s simple authentication mechanism. This setting activates the Password (Simple Authentication) field.
Network Management 4. If the Simple authentication method is selected, specify a password of up to 15 alphanumeric characters in the Password (Simple Authentication) area. 5. If the MD5 authentication method is selected, fill in the Key #1 field (Key #2 is optional). Enter any numeric value between 0 and 256 into the MD5 ID area. Enter a string consisting of up to 16 alphanumeric characters in the MD5 Auth Key area. 6. Click the OK button to return to the Router screen.
5-74 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • Packets are compared with lines of the filter policy list until a match is made. Once a packet matches a line of the list, it's acted upon, and no further comparisons take place. If inspected packets are determined to not be IP packets, it permitted by the access point for its inbound or outbound destination. Once you create a filter policy, apply it to an interface in either an incoming or outgoing direction.
Network Management NOTE With IP Filtering, users can only define a destination port, not a source port. 2. Click the Add button to define the attributes of a new IP Filtering policy. The following policy (or filtering rule) attributes require definition. Filter name Create a name for the filter policy unique to its function in order to differentiate it from others that may have somewhat similar configurations. Protocol Specify the protocol used for the filter policy.
5-76 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide In Use Displays YES if the listed filter policy is currently being utilized by LAN1, LAN2 or a WLAN. NO is displayed if the listed policy is currently not be utilized by either of the LAN ports or any of the access point’s 16 WLANs. NOTE Once filter policies have been defined, they can then be applied to traffic on either of the two access point LAN ports or any of the 16 access point WLANs.
Network Management c. Select the Enable IP Filtering button in the lower portion of the screen. d. Select the IP Filtering button. The screen displays with both the Default Incoming Deny and Default Outgoing Deny checkboxes selected by default. Consequently, if you enable IP filtering but do not apply any filters that allow IP traffic, then no IP traffic will be forwarded, as the default deny settings have precedence. 2. Use the Filter name drop menu to select an existing filter. 3.
5-78 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
Configuring Access Point Security Security measures for the AP-7131N-FGR and its ‘WLANs are critical. Use the available AP-7131N-FG security options to protect the access point LAN from wireless vulnerabilities, and safeguard the transmission of RF packets between the access point and its associated MUs. WLAN security can be configured on an ESS by ESS basis on the access point. Sixteen separate ESSIDs (WLANs) can be supported on an access point, and must be managed (if necessary) between the 802.
6-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE Security for the access point can be configured in various locations throughout the access point menu structure. This chapter outlines the security options available to the AP-7131N-FGR, and the menu locations and steps required to configure specific security measures. 6.
Configuring Access Point Security 3. Start Internet Explorer (with Sun Micro Systems’ Java Runtime Environment (JRE) 1.6 or higher installed) and type in the default IP address in the address field. To connect to the access point, the IP address is required. If connected to the access point using the WAN port, the default static IP address is 10.1.1.1. The default password is “motorola.” If connected to the access point using the LAN port, the default static IP address is 192.168.0.1/24.
6-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION Restoring the access point’s configuration back to default settings changes the administrative password back to “motorola.” If restoring the configuration back to default settings, be sure you change the administrative password accordingly. 5. Enter the previous password and the new admin password in the two fields provided. Click the Apply button.
Configuring Access Point Security have been created, they are selectable within the Security field of each WLAN screen. If the existing default security policy does not satisfy the data protection requirements of a specific WLAN, a new security policy (using the authentication and encryption schemes discussed above) can be created. CAUTION Mesh configurations do not support mismatched security policies when operating using a mixed mode scheme.
6-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide WPA2/CCMP (802.11i) Select the WPA2/CCMP (802.11) button to display the WPA2/ CCMP Settings field within the New Security Policy screen. For detailed information on configuring WPA2/CCMP, see Configuring WPA2-CCMP (802.11i) on page 6-11. 6. Click Apply to keep changes made within the New Security Policy screen (if any).
Configuring Access Point Security The New Security Policy screen displays with no authentication or encryption options selected. 3. Select the 802.1x EAP radio button. The 802.1x EAP Settings field displays within the New Security Policy screen. 4. Ensure the Name of the security policy entered suits the intended configuration or function of the policy. 5. If using the access point’s Internal Radius server, leave the Radius Server drop-down menu in the default setting of Internal.
6-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6. Configure the Server Settings field as required to define address information for the authentication server. The appearance of the Server Settings field varies depending on whether Internal or External has been selected from the Radius Server drop-down menu. Radius Server Address If using an External Radius Server, specify the numerical (non-DNS) IP address of a primary Remote Dial-In User Service (Radius) server.
Configuring Access Point Security 7. Select the Accounting tab as required to define a timeout period and retry interval Syslog for MUs interoperating with the access point and EAP authentication server. The items within this tab could be enabled or disabled depending on whether Internal or External has been selected from the Radius Server drop-down menu. MU Timeout Specify the time (in seconds) for the access point’s retransmission of EAP-Request packets. The default is 10 seconds.
6-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE The default values described are the recommended values. Do not change these values unless consulted otherwise by an administrator. 9. Select the Advanced Settings tab as required to specify a MU quiet period, timeout interval, transmit period, and retry period for MUs and the authentication server.
Configuring Access Point Security 6.5 Configuring WPA2-CCMP (802.11i) WPA2 is a newer 802.11i standard that provides even stronger wireless security than Wi-Fi Protected Access (WPA). CCMP is the security standard used by the Advanced Encryption Standard (AES). CCMP computes a Message Integrity Check (MIC) using the proven Cipher Block Chaining (CBC) technique. Changing just one bit in a message produces a totally different result.
6-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5. Configure the Key Rotation Settings field as required to set Broadcast Key Rotation and the update interval. Broadcast Key Rotation Select the Broadcast Key Rotation checkbox to enable or disable broadcast key rotation. When enabled, the key indices used for encrypting/decrypting broadcast traffic will be alternatively rotated on every interval specified in the Broadcast Key Rotation Interval.
Configuring Access Point Security 6. Configure the Key Settings area as needed. 256-bit Key To use a hexadecimal value (and not an ASCII passphrase), select the checkbox and enter 16 hexadecimal characters into each of the four fields displayed. Default (hexadecimal) 256-bit keys for WP2A/CCMP include: 1011121314151617 18191A1B1C1D1E1F 2021222324252627 28292A2B2C2D2E2F 7. Configure the Fast Roaming (802.1x only) field as required to enable additional access point roaming and key caching options.
6-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Use the access point’s Firewall screen to enable or disable the configurable firewall filters. Enable each filter for maximum security. Disable a filter if the corresponding attack does not seem a threat in order to reduce processor overhead. Use the WLAN Security screens as required for setting user authentication and data encryption parameters. To configure the access point firewall settings: 1.
Configuring Access Point Security 3. Refer to the DOS Attack Checks field to set the following firewall filters: SYN Flood Attack Check A SYN flood attack requests a connection and then fails to promptly acknowledge a destination host's response, leaving the destination host vulnerable to a flood of connection requests.
6-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6.6.1 Configuring LAN to WAN Access The access point LAN can be configured to communicate with the WAN side of the access point. Use the Subnet Access screen to control access from the LAN1 (or LAN2) interfaces to the WAN interface. This access level will function as an ACL in a router to allow/deny certain IP addresses or subnets to access certain interfaces (or subnets belonging to those interfaces) by creating access policies.
Configuring Access Point Security 3. Click Apply to save any changes to the Subnet Access screen. Navigating away from the screen without clicking the Apply button results in all changes to the screens being lost. 4. Click Undo Changes (if necessary) to undo any changes made. Undo Changes reverts the settings displayed on the Subnet Access screen to the last saved configuration. 5. Click Logout to securely exit the Access Point applet. A prompt displays confirming the logout before the applet is closed.
6-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • • TCP - Transmission Control Protocol is a set of rules for sending data as message units over the Internet. TCP manages individual data packets. Messages are divided into packets for efficient routing through the Internet. UDP - User Datagram Protocol is used for broadcasting data over the Internet. Like TCP, UDP runs on top of Internet Protocol (IP) networks. Unlike TCP/IP, UDP/IP provides few error recovery services.
Configuring Access Point Security 2. Configure the Settings field as needed to override the settings in the Subnet Access screen and import firewall rules into the Advanced Subnet Access screen. Override Subnet Access settings Select this checkbox to enable advanced subnet access rules and disable existing subnet access rules, port forwarding, and 1 to many mappings from the system.
6-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Configure the Firewall Rules field as required add, insert or delete firewall rules into the list of advanced rules. Inbound or Outbound Select Inbound or Outbound from the drop-down menu to specify if a firewall rule is intended for inbound traffic to an interface or outbound traffic from that interface. Add Click the Add button to insert a new rule at the bottom of the table.
Configuring Access Point Security Move Down Clicking the Move Down button moves the selected rule down by one row in the table. The index numbers for the affected rows adjust to reflect the new order. Index The index number determines the order firewall rules are executed. Rules are executed from the lowest number to the highest number. Rule Id Rule Id is read-only and automatically set when Apply button is clicked.
6-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6.7 Configuring VPN Tunnels Create a VPN tunnel to ensure data privacy between two end points, even while using an insecure communication medium like the Internet. VPNs use a secure tunnel between two end points as if they are directly connected over a secure connection. The access point allows up to 25 VPN tunnels to either a VPN endpoint or to another access point.
Configuring Access Point Security 2. Use the VPN Tunnels field to add or delete a tunnel to the list of available tunnels, list tunnel network address information and display key exchange information for each tunnel. Add Click Add to add a VPN tunnel to the list. To configure a specific tunnel, select it from the list and use the parameters within the VPN Tunnel Config field to set its properties. Del Click Del to delete a highlighted VPN tunnel. There is no confirmation before deleting the tunnel.
6-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Remote Gateway The Remote Gateway column lists a remote gateway IP address for each tunnel. The numeric remote gateway is the gateway IP address on the remote network the VPN tunnel connects to. Ensure the address is the same as the WAN port address of the target gateway AP or switch. Key Exchange Type The Key Exchange Type column lists the key exchange type for passing keys between both ends of a VPN tunnel.
Configuring Access Point Security Local WAN IP Enter the WAN’s numerical (non-DNS) IP address in order for the tunnel to pass traffic to a remote network. Remote Subnet Specify the numerical (non-DNS) IP address for the Remote Subnet. Remote Subnet Mask Enter the subnet mask for the tunnel’s remote network for the tunnel. The remote subnet mask is the subnet setting for the remote network the tunnel connects to. Remote Gateway Enter a numerical (non-DNS) remote gateway IP address for the tunnel.
6-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5. Click Undo Changes (if necessary) to undo any changes made. Undo Changes reverts the settings displayed on the VPN, Auto Key Settings, IKE Settings and Manual Key Settings screens to the last saved configuration. 6. Click Logout to securely exit the Access Point applet. A prompt displays confirming the logout before the applet is closed. 6.7.
Configuring Access Point Security 10. 11. 12. 13. Select ESP with Authentication and AES 128-bit. Click OK. Select the IKE Settings button. Select Pre Shared Key (PSK). Enter the Passphrase. Passphrases must match on both VPN devices. 14. Select AES 128-bit. 15. Select Group 2. 16. Click OK. This will take you back to the main VPN configuration screen. 17. Click Apply to save the updates 18. Select Network Configuration -> WAN -> VPN -> VPN Status from the access point menu tree.
6-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Notice the status displays "NOT_ACTIVE". This screen automatically refreshes to get the current status of the VPN tunnel. Once the tunnel is active, the IKE_STATE changes from NOT_CONNECTED to SA_MATURE. 19. On AP #2, repeat the same steps as above. However, replace AP #2 information with AP #1 information. 20. Once both tunnels are established, ping each side to ensure connectivity. 6.7.
Configuring Access Point Security 3. Configure the Manual Key Settings screen to modify the following: NOTE When entering Inbound or Outbound encryption or authentication keys, an error message could display stating the keys provided are “weak”. Some attack tools invoke a dictionary to hack keys based on commonly used words. To avoid entering a weak key, try to not to produce a key using commonly used terms and attempt to mix alphabetic and numerical key attributes when possible.
6-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AH Authentication AH provides data authentication and anti-replay services for the VPN tunnel. Select the required authentication method from the drop-down menu: • None - Disables AH authentication. The rest of the fields are not active. • SHA1 - Enables Secure Hash Algorithm 1, requiring 160-bit (40-character hexadecimal) keys.
Configuring Access Point Security ESP Encryption Algorithm Select the encryption and authentication algorithms for the VPN tunnel using the drop-down menu. • AES 128-bit - Uses the Advanced Encryption Standard algorithm with 128-bit (32-character hexadecimal) keys. • AES 192-bit - Uses the Advanced Encryption Standard algorithm with 192-bit (48-character hexadecimal) keys. • AES 256-bit - Uses the Advanced Encryption Standard algorithm with 256-bit (64-character hexadecimal) keys.
6-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The Inbound and Outbound SPI settings are required to be interpolated to function correctly. For example: • AP1 Inbound SPI = 800 • AP1 Outbound SPI = 801 • AP2 Inbound SPI = 801 • AP2 Outbound SPI = 800 4. Click Ok to return to the VPN screen. Click Apply to retain the settings made on the Manual Key Settings screen. 5. Click Cancel to return to the VPN screen without retaining the changes made to the Manual Key Settings screen.
Configuring Access Point Security AH Authentication AH provides data authentication and anti-replay services for the VPN tunnel. Select the desired authentication method from the drop-down menu. • SHA1 - Enables Secure Hash Algorithm 1. No keys are required to be manually provided. ESP Type ESP provides packet encryption, optional data authentication and anti-replay services for the VPN tunnel. Use the drop-down menu to select the ESP type. • ESP - Enables ESP for this tunnel.
6-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6.7.4 Configuring IKE Key Settings The Internet Key Exchange (IKE) is an IPsec standard protocol used to ensure security for VPN negotiation and remote host or network access. IKE provides an automatic means of negotiation and authentication for communication between two or more parties. In essence, IKE manages IPSec keys automatically for the parties. To configure IKE key settings for the access point: 1.
Configuring Access Point Security Operation Mode The Phase I protocols of IKE is based on the ISAKMP identityprotection. IKE main mode refers to the identity-protection exchange. • Main - Standard IKE mode for communication and key exchange. Local ID Type Select the type of ID to be used for the access point end of the SA. • IP - Select IP if the local ID type is the IP address specified as part of the tunnel. • FQDN - Use FQDN if the local ID is a fully qualified domain name (such as sj.motorola.com).
6-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide IKE Authentication Passphrase If you selected Pre-Shared Key as the authentication mode, you must provide a passphrase. IKE Encryption Algorithm Select the encryption and authentication algorithms for the VPN tunnel from the drop-down menu. • AES 128-bit - Uses the Advanced Encryption Standard algorithm with 128-bit. No keys are required to be manually provided.
Configuring Access Point Security To view VPN status: 1. Select Network Configuration -> WAN -> VPN -> VPN Status from the access point menu tree. 2. Reference the Security Associations field to view the following: Tunnel Name The Tunnel Name column lists the names of all the tunnels configured on the access point. For information on configuring a tunnel, see Configuring VPN Tunnels on page 6-22. Status The Status column lists the status of each configured tunnel.
6-38 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Inb SPI The Inb SPI column displays the inbound Security Parameter Index (SPI) for each of the tunnels. The SPI is used locally by the access point to identify a security association. There are unique outbound and inbound SPIs. Life Time Use the Life Time column to view the lifetime associated with a particular Security Association (SA). Each SA has a finite lifetime defined.
Configuring Access Point Security 6.8 Configuring Content Filtering Settings Content filtering allows system administrators to block specific commands and URL extensions from going out through the access point’s WAN port. Therefore, content filtering affords system administrators selective control on the content proliferating the network and is a powerful data and network screening tool.
6-40 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Block Outbound HTTP HyperText Transport Protocol (HTTP) is the protocol used to transfer information to and from Web sites. HTTP Blocking allows for blocking of specific HTTP commands going outbound on the access point WAN port. HTTP blocks commands on port 80 only.
Configuring Access Point Security Block Outbound SMTP Simple Mail Transport Protocol (SMTP) is the Internet standard for Commands host-to-host mail transport. SMTP generally operates over TCP on port 25. SMTP filtering allows the blocking of any or all outgoing SMTP commands. Check the box next to the command to disable that command when using SMTP across the access point’s WAN port. • HELO - (Hello) Identifies the SMTP sender to the SMTP receiver.
6-42 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Block Outbound FTP Actions File Transfer Protocol (FTP) is the Internet standard for host-to-host mail transport. FTP generally operates over TCP port 20 and 21. FTP filtering allows the blocking of any or all outgoing FTP functions. Check the box next to the command to disable the command when using FTP across the access point’s WAN port.
Configuring Access Point Security The rogue detection interval is used in conjunction with Motorola MUs that identify themselves as rogue detection capable to the access point. The detection interval defines how often the access point requests these MUs to scan for a rogue AP. A shorter interval can affect the performance of the MU, but it will also decrease the time it takes for the access point to scan for a rogue AP.
6-44 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION Users cannot define a rogue detection method when one of the access point radios is functioning as a WIPS sensor. To use one of the radios as a detector, you must disable WIPS sensor mode first, then set a radio for the desired detection method. 2. Configure the Detection Method field to set the detection method (MU or access point) and define the 802.11a/n or 802.11b/g/n radio to conduct the rogue AP search.
Configuring Access Point Security RF Scan by MU Select the RF Scan by MU checkbox to enable MUs to scan for potential rogue APs within the network. Define an interval in the Scan Interval field for associated MUs to beacon in an attempt to locate a rogue AP. Set the interval to a value sooner than the default if a large volume of device network traffic is anticipated within the coverage area of the target access point. The Scan Interval field is not available unless the RF Scan by MU checkbox is selected.
6-46 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Del (Delete) Click the Delete button to remove the highlighted line from the Rule Management field. The MAC and ESS address information previously defined is no longer applicable unless the previous configuration is restored. Delete All Click the Delete All button to remove all entries from the Rule Management field.
Configuring Access Point Security The Active APs screen displays with detected rogue devices displayed within the Rogue APs table. 2. Enter a value (in minutes) in the Allowed APs Age Out Time field to indicate the number of elapsed minutes before an AP will be removed from the approved list and reevaluated. A zero (0) for this value (default value) indicates an AP can remain on the approved AP list permanently. 3.
6-48 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 6. Highlight a rogue AP and click the Details button to display a screen with device and detection information specific to that rogue device. This information is helpful in determining if a rogue AP should be moved to the Allowed APs table. For more information on the displaying information on detected rogue APs, see Displaying Rogue AP Details on page 6-48. 7.
Configuring Access Point Security 3. Refer to the Rogue AP Detail field for the following information: BSSID/MAC Displays the MAC address of the rogue AP. This information could be useful if the MAC address is determined to be a Motorola MAC address and the device is interpreted as non-hostile and the device should be defined as an allowed AP. ESSID Displays the ESSID of the rogue AP.
6-50 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Detection Method Displays the RF Scan by MU, RF On-Channel Detection or RF Scan by Detector Radio method selected from the Rogue AP screen to detect rogue devices. For information on detection methods, see Configuring Rogue AP Detection on page 6-42. First Heard (days:hrs:min) Defines the time in (days:hrs:min) that the rogue AP was initially heard by the detecting AP.
Configuring Access Point Security 2. Highlight an MU from within the Rogue AP enabled MUs field and click the scan button. The target MU begins scanning for rogue devices using the detection parameters defined within the Rogue AP Detection screen. To modify the detection parameters, see Configuring Rogue AP Detection on page 6-42. Those devices detected as rogue APs display within the Scan Result table.
6-52 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5. Highlight a different MU from the Rogue AP enabled MUs field as needed to scan for additional rogue APs. 6. Click Logout to return to the Rogue AP Detection screen. 6.10 Configuring User Authentication The access point can work with Radius and external LDAP Servers (AAA Servers) to provide user database information and user authentication. 6.10.
Configuring Access Point Security 2. From within the Data Source Configuration field, use the Data Source drop-down menu to select the data source for the Radius server. Local An internal user database serves as the data source. Use the User Database screen to enter the user data. For more information, see Managing the Local User Database on page 6-61. LDAP If LDAP is selected, the switch will use the data in an LDAP server.
6-54 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Use the TTLS/PEAP Configuration field to specify the Radius Server default EAP type, EAP authentication type and a Server or CA certificate (if used). EAP Type Use the EAP Type checkboxes to enable the default EAP type(s) for the Radius server. Options include: • PEAP - Select the PEAP checkbox to enable both PEAP types (GTC and MSCHAP-V2) available to the access point.
Configuring Access Point Security Default Authentication Type Specify a PEAP and/or TTLS Authentication Type for EAP to use from the drop-down menu to the right of each checkbox item. PEAP options include: • GTC - EAP Generic Token Card (GTC) is a challenge handshake authentication protocol using a hardware token card to provide the response string. • MSCHAP-V2 - Microsoft CHAP (MSCHAP-V2) is an encrypted authentication method based on Microsoft's challenge/ response authentication protocol.
6-56 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CA Certificate You can also choose an imported CA Certificate to use on the Radius server. If using a server certificate signed by a CA, import that CA's root certificate using the CA certificates screen (for information, see Importing a CA Certificate on page 4-18). After a valid CA certificate has been imported, it is available from the CA Certificate drop-down menu.
Configuring Access Point Security 6.10.2 Configuring LDAP Authentication When the Radius Data Source is set to use an external LDAP server (see Configuring the Radius Server on page 6-52), the LDAP screen is used to configure the properties of the external LDAP server. To configure the LDAP server: 1. Select System Configuration -> User Authentication -> RADIUS Server -> LDAP from the menu tree. CAUTION Ensure IPSec has been properly configured to protect communications with the external LDAP server.
6-58 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Enter the appropriate information within the LDAP Configuration field to allow the access point to interoperate with the LDAP server. Consult with your LDAP server administrator for details on how to define the values in this screen. LDAP Server IP Enter the IP address of the external LDAP server acting as the data source for the Radius server.
Configuring Access Point Security Bind Distinguished Name Specify the distinguished name used to bind with the LDAP server. Password Enter a valid password for the LDAP server. The password length must be 8 to 16 characters. Base Distinguished Name Enter a name that establishes the base object for the search. The base object is the point in the LDAP tree at which to start searching. Group Attribute Define the group attribute used by the LDAP server.
6-60 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide CAUTION When configuring the credentials of an MU, ensure its login (or user) name is a Fully Qualified Domain Name (FQDN), or it cannot be authenticated by the access point’s proxy server. For example; ap7131@2kserver.FUSCIA.com. To configure the proxy Radius server for the access point: 1. Select System Configuration -> User Authentication -> RADIUS Server -> Proxy from the menu tree.
Configuring Access Point Security Retry Count Enter a value between 3 and 6 to indicate the number of times the access point attempts to reach a proxy server before giving up. Timeout Enter a value between 5 and 10 to indicate the number of elapsed seconds causing the access point to time out on a request to a proxy server. 3. Use the Add button to add a new proxy server. Define the following information for each entry: Suffix Enter the domain suffix (such as myisp.com or mycompany.
6-62 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE Each group can be configured to have its own access policy using the Access Policy screen. For more information, see Defining User Access Permissions by Group on page 6-67. 1. Select System Configuration -> User Authentication -> User Database from the menu tree. Refer to the Groups field for a list of all groups in the local Radius database. The groups are listed in the order added.
Configuring Access Point Security 6.10.4.2 Management Users 1. The Management Users table displays the list of management users. ClearAll button is available for default management user account only. 2. The Add and Delete buttons are read only for all managment users, except the default management user. The admin account is the default management user account.
6-64 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. In the new line, type a User ID (user name). 5. Click the Change Login Password button. A small window displays. Enter a new password for the user and click Apply button to save the changes. Change Login Password button is available for non default management user accounts only. 6. Click Apply to save any changes to the Users screen.
Configuring Access Point Security 7. Click Undo Changes (if necessary) to undo any changes made. Undo Changes reverts the settings displayed on the Users screen to the last saved configuration. 8. Click Logout to securely exit the Access Point applet. A prompt displays confirming the logout before the applet is closed. 6.10.4.3 Mapping Users to Groups This applies to wireless users only.
6-66 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. To add the user to a group, select the group in the Available list (on the right) and click the <-Add button. Assigned users will display within the Assigned table. Map one or more groups as needed for group authentication access for this particular user. 4. To remove the user from a group, select the group in the Assigned list (on the left) and click the Delete-> button. 5.
Configuring Access Point Security 6.10.5 Defining User Access Permissions by Group This applies to wireless users only. An AAA server maintains the users and groups database used by the access point for access permissions. Various kinds of access policies can be applied to each group. Individual groups can be associated with their own time-based access policy. Each group’s policy has a user defined interval defining the days and hours access is permitted.
6-68 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The Access Policy screen displays the following fields: Groups The Groups field displays the names of those existing groups that can have access intervals applied to them. Click the Edit button to display a screen designed to create access intervals for specific days and hours. A mechanism also exists for mapping specific WLANs to these intervals. For more information, see Editing Group Access Permissions on page 6-69.
Configuring Access Point Security Associated WLANs The Associated WLANs field displays the WLANs assigned the user group access permissions listed within the filters and grid fields. Add additional WLANs to a group by selecting the Edit button within the groups field. grid Refer to the grid field to review a bar graph of the selected group’s access privileges. Revise the selected group’s privileges as needed to 2.
6-70 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. Define up to 10 access policies for the selected group within the Time Based Access Policy field. Use the drop-down menus on the left-hand side of the screen to define the day of the week for which each policy applies. If continual access is required, select the All Days option. If continual access is required during Monday through Friday, but not Saturday or Sunday, select the Weekdays option.
Configuring Access Point Security NOTE Groups have a strict start and end time (as defined using the Edit Access Policy screen). Only during this period of time can authentication requests from users be honored (with no overlaps). Any authentication request outside of this defined interval is denied regardless of whether a user’s credentials match or not. 5. Refer to the WLANs field to select existing WLANs to apply to the selected group’s set of access permissions.
6-72 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
Monitoring Statistics The access point has functionality to display robust transmit and receive statistics for its WAN and LAN port. Wireless Local Area Network (WLAN) stats can also be displayed collectively for each enabled WLAN as well as individually for up to 16 specific WLANs. Transmit and receive statistics can also be displayed for the access point’s 802.11a/n and 802.11b/g/n radios.
7-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide See the following sections for more details on viewing statistics for the access point: • • • • • • • Viewing WAN Statistics Viewing LAN Statistics Viewing Wireless Statistics Viewing Radio Statistics Summary Viewing MU Statistics Summary Viewing the Mesh Statistics Summary Viewing Known Access Point Statistics 7.
Monitoring Statistics 2. Refer to the Information field to reference the following access point WAN data: Status The Status field displays Enabled if the WAN interface is enabled on the WAN screen. If the WAN interface is disabled on the WAN screen, the WAN Stats screen displays no connection information and statistics. To enable the WAN connection, see Configuring WAN Settings on page 5-16 HW Address The Media Access Control (MAC) address of the access point WAN port.
7-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Mask The Mask field displays the subnet mask number for the access point’s WAN connection. This value is set on the WAN screen. Refer to Configuring WAN Settings on page 5-16 to change the subnet mask. Link The Link parameter displays Up if the WAN connection is active between the access point and network, and Down if the WAN connection is interrupted or lost.
Monitoring Statistics RX Frame The RX Frame field displays the number of TCP/IP data frame errors received. 4. Refer to the Transmitted field to reference data received over the access point WAN port. TX Packets TX packets are data packets sent over the WAN connection. The displayed number is a cumulative total since the WAN was last enabled or the access point was last restarted. To begin a new data collection, see Configuring System Settings on page 4-2.
7-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 7.2 Viewing LAN Statistics Use the LAN Stats screen to monitor the activity of the access point’s LAN1 or LAN2 connection. The Information field of the LAN Stats screen displays network traffic information as monitored over the access point LAN1 or LAN2 port.
Monitoring Statistics Status Displays whether this particular LAN has been enabled as viable subnet from within the LAN Configuration screen. IP Address The Internet Protocol (IP) addresses for the access point LAN port. Network Mask The first two sets of numbers specify the network domain, the next set specifies the subset of hosts within a larger network. These values help divide a network into subnetworks and simplify routing and data transmission.
7-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide RX Errors RX errors include dropped data packets, buffer overruns, and frame errors on inbound traffic. The number of RX errors is a total of RX Dropped, RX Overruns and RX Carrier errors. Use this information to determine performance quality of the current LAN connection. RX Dropped The RX Dropped field displays the number of data packets failing to reach the LAN port.
Monitoring Statistics TX Carrier The TX Carrier field displays the number of TCP/IP data carrier errors. 5. Click the Clear LAN Stats button to reset each of the data collection counters to zero in order to begin new data collections. The RX/TX Packets and RX/TX Bytes totals remain at their present values and are not cleared. 6. Click the Logout button to securely exit the Access Point applet. There will be a prompt confirming logout before the applet is closed. 7.2.
7-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Refer to the Spanning Tree Info field to for details on spanning tree state, and root access point designation. Spanning Tree State Displays whether the spanning tree state is currently enabled or disabled. The spanning tree state must be enabled for a unique spanning-tree calculation to occur when the bridge is powered up or when a topology change is detected.
Monitoring Statistics Root Path Cost Bridge message traffic contains information identifying the root bridge and the sending bridge. The root path cost represents the distance (cost) from the sending bridge to the root bridge. Bridge Max Msg. Age The Max Msg Age measures the age of received protocol information recorded for a port, and to ensure the information is discarded when it exceeds the value set for the Maximum Message age timer. For information on setting the Maximum Message Age.
7-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Designated Bridge There is only one root bridge within each mesh network. All other bridges are designated bridges that look to the root bridge for several mesh network timeout values. For information on root and bridge designations, see Setting the LAN Configuration for Mesh Networking Support on page 9-7. Designated Port Each designated bridge must use a unique port.
Monitoring Statistics 2. Refer to the WLAN Summary field to reference high-level data for each enabled WLAN. Name Displays the names of all the enabled WLANs on the access point. For information on enabling a WLAN, see Configuring WAN Settings on page 5-16. MUs Displays the total number of MUs currently associated with each enabled WLAN. Use this information to assess if the MUs are properly grouped by function within each enabled WLAN.
7-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide % NU Displays a percentage of the total packets for each active WLAN that are non-unicast. Non-unicast packets include broadcast and multicast packets. Retries Displays the average number of retries per packet. An excessive number could indicate possible network or hardware problems. Clear All WLAN Stats Click this button to reset each of the data collection counters to zero in order to begin new data collections.
Monitoring Statistics 7.3.1 Viewing WLAN Statistics Use the WLAN Stats screen to view detailed statistics for individual WLANs.The WLAN Stats screen is separated into four fields; Information, Traffic, RF Status, and Errors. The Information field displays basic information such as number of associated Mobile Units, ESSID and security information. The Traffic field displays statistics on RF traffic and throughput. The RF Status field displays information on RF signal averages from the associated MUs.
7-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide ESSID Displays the Extended Service Set ID (ESSID) for the target WLAN. Radio/s Displays the name of the 802.11a/n or 802.11b/g/n radio the target WLAN is using for access point transmissions. Authentication Type Displays the authentication type defined for the WLAN. If the authentication type does not match the desired scheme for the WLAN or needs to be enabled, see Enabling Authentication and Encryption Schemes on page 6-4.
Monitoring Statistics Avg. Bit Speed The Total column displays the average bit speed in Mbps for a given time period on the selected WLAN.This includes all packets that are sent and received. The number in black represents statistics for the last 30 seconds and the number in blue represents statistics for the last hour. If the bit speed is significantly slower than the selected data rate, refer to the RF Statistics and Errors fields to troubleshoot.
7-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Dropped Packets Displays the percentage of packets which the AP gave up on for all MUs associated with the selected WLAN. The number in black represents this statistic for the last 30 seconds and the number in blue represents this statistic for the last hour. % of Undecryptable Pkts Displays the percentage of undecryptable packets for all MUs associated with the selected WLAN.
Monitoring Statistics 2. Refer to the Radio Summary field to reference access point radio information. Type Displays the type of radio (either 802.11a/n or 802.11b/g/n) currently deployed by the access point. To configure the radio type, see Setting the WLAN’s Radio Configuration on page 5-51. MUs Displays the total number of MUs currently associated with each access point radio. T-put Displays the total throughput in Megabits per second (Mbps) for each access point radio listed.
7-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide % NU Displays the percentage of the total packets that are non-unicast. Non-unicast packets include broadcast and multicast packets. Retries Displays the average number of retries per packet on each radio. A high number could indicate network or hardware problems. 3. Click the Clear All Radio Stats button to reset each of the data collection counters to zero in order to begin new data collections.
Monitoring Statistics 2. Refer to the Information field to view the access point 802.11a/n or 802.11b/g/n radio’s MAC address, placement and transmission information. HW Address The Media Access Control (MAC) address of the access point housing the 802.11a/n radio. The MAC address is set at the factory and can be found on the bottom of the access point. For more information on how access point MAC addresses are assigned, see MAC Address Assignment on page 1-29.
7-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Placement Lists whether the access point radio is indoors or outdoors. To change the placement setting, see Configuring the 802.11a/n or 802.11b/g/n Radio on page 5-56. Current Channel Indicates the channel for communications between the access point radio and its associated MUs. To change the channel setting, see Configuring the 802.11a/n or 802.11b/g/n Radio on page 5-56.
Monitoring Statistics 4. Refer to the RF Status field to view the following MU signal, noise and performance information for the target access point 802.11a/n or 802.11b/g/n radio. Avg MU Signal Displays the average RF signal strength in dBm for all MUs associated with the radio. The number in black represents the average signal for the last 30 seconds and the number in blue represents the average signal for the last hour.
7-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 7. Click the Logout button to securely exit the Access Point applet. 7.4.1.1 Retry Histogram Refer to the Retry Histrogram screen for an overview of the retries transmitted by an access point radio and whether those retries contained any data packets. Use this information in combination with the error fields within a Radio Stats screen to assess overall radio performance.
Monitoring Statistics abundance of retries warrants reconfiguring the access point radio to achieve better performance. 2. Click Apply to save any changes to the Radio Histogram screen. Navigating away from the screen without clicking Apply results in changes to the screens being lost. 3. Click Undo Changes (if necessary) to undo any changes made to the screen. Undo Changes reverts the settings to the last saved configuration. 4. Click Logout to securely exit the Access Point applet.
7-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Refer to the MU List field to reference associated MU address, throughput and retry information. IP Address Displays the IP address of each of the associated MU. MAC Address Displays the MAC address of each of the associated MU. WLAN Displays the WLAN name each MU is interoperating with. Radio Displays the name of the 802.11a/n or 802.11b/g/n radio each MU is associated with.
Monitoring Statistics Hotspot Displays whether this radio is currently supporting a hotspot. 3. Click the Refresh button to update the data collections displayed without resetting the data collections to zero. 4. Click the Echo Test button to display a screen for verifying the link with an associated MU. For detailed information on conducting a ping test for an MUs, see Pinging Individual MUs on page 7-30. NOTE An echo test initiated from the access point MU Stats Summary screen uses WNMP pings.
7-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 1. 2. 3. 4. Select Status and Statistics -> MU Stats from the access point menu tree. Highlight a specific MU. Select the MU Details button. Refer to the MU Properties field to view MU address information. IP Address Displays the IP address of the MU. WLAN Association Displays the name of the WLAN the MU is associated with. Use this information to assess whether the MU is properly grouped within that specific WLAN.
Monitoring Statistics Throughput The Total column displays the average total packets per second crossing the selected MU. The Rx column displays the average total packets per second received on the MU. The Tx column displays the average total packets per second sent on the MU. The number in black represents throughput for the last 30 seconds, the number in blue represents throughput for the last hour. Avg.
7-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Avg Num of Retries Displays the average number of retries for the MU. The number in black represents average retries for the last 30 seconds and the number in blue represents average retries for the last hour. Dropped Packets Displays the percentage of packets the AP gave up as not received on for the selected MU.
Monitoring Statistics 4. Click the Ping button to begin transmitting ping packets to the station address specified. Refer to the Number of Responses parameter to assess the number of responses from the target MU versus the number of pings transmitted by the access point. Use the ratio of packets sent versus packets received to assess the link quality between MU and the access point Click the Ok button to exit the Echo Test screen and return to the MU Stats Summary screen. 7.5.
7-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 7.6 Viewing the Mesh Statistics Summary The access point has the capability of detecting and displaying the properties of other access points in mesh network (either base bridges or client bridges) mode. This information is used to create a list of known wireless bridges. To view detected mesh network statistics: 1. Select Status and Statistics -> Mesh Stats from the access point menu tree.
Monitoring Statistics MAC Address The unique 48-bit, hard-coded Media Access Control address, known as the devices station identifier. This value is hard coded at the factory by the manufacturer and cannot be changed. WLAN Displays the WLAN name each wireless bridge is interoperating with. Radio Displays the name of the 802.11a/n or 802.11b/g/n radio each bridge is associated with. T-put Displays the total throughput in Megabits per second (Mbps) for each associated bridge.
7-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 4. Click the Logout button to securely exit the Access Point applet. A prompt displays confirming the logout before the applet is closed. 7.7 Viewing Known Access Point Statistics The access point has the capability of detecting and displaying the properties of other Motorola access points located within its coverage area.
Monitoring Statistics indicating their channel, IP address, firmware version, etc. This information is used to create a known AP list. The list has field indicating the properties of the access point discovered. NOTE The Known AP Statistics screen only displays statistics for access points located on the same subnet. To view detected access point statistics: 1. Select Status and Statistics -> Known AP Stats from the access point menu tree.
7-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide MUs The number MUs associated with the located access point. Unit Name Displays the name assigned to the access point using the System Settings screen. For information on changing the unit name, see Configuring System Settings on page 4-2. 2. Click the Clear Known AP Stats button to reset each of the data collection counters to zero in order to begin new data collections. 3.
CLI Reference The access point Command Line Interface (CLI) is accessed through the serial port or a SSH session. The access point CLI follows the same conventions as the Web-based user interface. The CLI does, however, provide an “escape sequence” to provide diagnostics for problem identification and resolution. The CLI treats the following as invalid characters: < > | " & \ ? , In order to avoid problems when using the CLI, these characters should be avoided.
8-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.1 Connecting to the CLI 8.1.1 Accessing the CLI through the Serial Port To connect to the access point CLI through the serial port: 1. Connect one end of a null modem serial cable to the access point’s serial connector. 2. Attach the other end of the null modem serial cable to the serial port of a PC running HyperTerminal or a similar emulation program. 3.
CLI Reference 8.2 Admin and Common Commands AP7131N>admin> Description: Displays admin configuration options. The items available under this command are shown below. Syntax: help passwd summary network system stats .. / save quit Displays general user interface help. Changes the admin password. Shows a system summary. Goes to the network submenu Goes to the system submenu. Goes to the stats submenu. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin>help Description: Displays general CLI user interface help. Syntax: help Displays command line help using combinations of function keys for navigation. Example: admin>help ? * Restriction of “?”: : display command help - Eg. ?, show ?, s? : “?” after a function argument is treated : as an argument : Eg. admin
CLI Reference AP7131N>admin>passwd Description: Changes the password for the admin login. Syntax: passwd Changes the admin password for access point access. This requires typing the old admin password and entering a new password and confirming it. Passwords can be between 8 and19 characters. The access point CLI treats the following as invalid characters: ' " \ & $ ^ * + ? [ ( { | , < > In order to avoid problems when using the access point CLI, these characters should be avoided.
8-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin>summary Description: Displays the access point’s system summary. Syntax: summary Displays a summary of high-level characteristics and settings for the WAN, LAN and WLAN. Example: admin>summary AP-713x firmware version : 4.0.2.
CLI Reference 8-7 AP7131N>admin>.. Description: Displays the parent menu of the current menu. This command appears in all of the submenus under admin. In each case, it has the same function, to move up one level in the directory structure. Example: admin(network.lan)>..
8-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin> / Description: Displays the root menu, that is, the top-level CLI menu. This command appears in all of the submenus under admin. In each case, it has the same function, to move up to the top level in the directory structure. Example: admin(network.
CLI Reference 8-9 AP7131N>admin>save Description: Saves the configuration to system flash. The save command appears in all of the submenus under admin. In each case, it has the same function, to save the current configuration. Syntax: save Saves configuration settings. The save command works at all levels of the CLI. The save command must be issued before leaving the CLI for updated settings to be retained.
8-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin>quit Description: Exits the command line interface session and terminates the session. The quit command appears in all of the submenus under admin. In each case, it has the same function, to exit out of the CLI. Once the quit command is executed, the login prompt displays again.
CLI Reference 8.3 Network Commands AP7131N>admin(network)> Description: Displays the network submenu. The items available under this command are shown below. lan wan wireless firewall router ipfilter .. / save quit Goes to the LAN submenu. Goes to the WAN submenu. Goes to the Wireless Configuration submenu. Goes to the Firewall submenu. Goes to the Router submenu. Goes to the IP Filter submenu Goes to the parent menu. Goes to the root menu. Saves the current configuration to the system flash.
8-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.1 Network LAN Commands AP7131N>admin(network.lan)> Description: Displays the LAN submenu. The items available under this command are shown below. show set bridge wlan-mapping dhcp type-filter ipfpolicy .. / save quit Shows current access point LAN parameters. Sets LAN parameters. Goes to the mesh configuration submenu. Goes to the WLAN/Lan/Vlan Mapping submenu. Goes to the LAN DHCP submenu.
CLI Reference AP7131N>admin(network.lan)> show Description: Displays the access point LAN settings. Syntax: show Shows the settings for the access point LAN1 and LAN2 interfaces. Displays information about individual LAN Example: admin(network.lan)>show Warning: This will display secure information, Do you want to continue? (n/y?)y LAN On Ethernet Port : LAN1 LAN Ethernet Timeout : disable 802.
8-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide LAN IP mode : DHCP server IP Address : 192.168.1.1 Network Mask : 255.255.255.255 Default Gateway : 192.168.1.1 Domain Name : Primary DNS Server : 192.168.0.2 Secondary DNS Server : 192.168.0.3 WINS Server : 192.168.0.255 admin(network.lan)> For information on displaying LAN information using the applet (GUI), see Configuring the LAN Interface on page 5-1.
CLI Reference AP7131N>admin(network.lan)> set Description: Sets the LAN parameters for the LAN port. Syntax: set lan name ethernet-port-lan timeout trunking native-vlan-tag Enables or disables the access point LAN interface. Defines the LAN name by index. Defines which LAN (LAN1 or LAN2) is active on the Ethernet port.
8-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Warning: This will display secure information. Do you want to continue [n/y]?y LAN On Ethernet Port : LAN1 LAN Ethernet Timeout : disable 802.1x Port Authentication: Username : admin Password : ******** Auto-negotiation : enable Speed : N/A Duplex : N/A ** LAN1 Information** LAN Name : LAN1 LAN Interface : enable 802.
CLI Reference 8-17 8.3.1.1 Network LAN, Bridge Commands AP7131N>admin(network.lan.bridge)> Description: Displays the access point Bridge submenu. show set .. / save quit Displays the mesh configuration parameters for the access point’s LANs. Sets the mesh configuration parameters for the access point’s LANs.. Moves to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI and exits the session.
8-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.bridge)> show Description: Displays the mesh bridge configuration parameters for the access point’s LANs. Syntax: show Displays mesh bridge configuration parameters for the access point’s LANs. Example: admin(network.lan.
CLI Reference 8-19 AP7131N>admin(network.lan.bridge)> set Description: Sets the mesh configuration parameters for the access point’s LANs. Syntax: set priority hello msgage fwddelay ageout Sets bridge priority time in seconds (0-65535) for specified LAN. Sets bridge hello time in seconds (1-10) for specified LAN. Sets bridge message age time in seconds (6-40) for specified LAN.
8-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.1.2 Network LAN, WLAN-Mapping Commands AP7131N>admin(network.lan.wlan-mapping)> Description: Displays the WLAN/Lan/Vlan Mapping submenu. show set create edit delete lan-map vlan-map .. / save quit Displays the VLAN list currently defined for the access point. Sets the access point VLAN configuration. Creates a new access point VLAN. Edits the properties of an existing access point VLAN. Deletes a VLAN.
CLI Reference AP7131N>admin(network.lan.wlan-mapping)> show Description: Displays the VLAN list currently defined for the access point.. These parameters are defined with the set command. Syntax: show name vlan-cfg lan-wlan wlan Displays the existing list of VLAN names. Shows WLAN-VLAN mapping and VLAN configuration. Displays a WLAN-LAN mapping summary. Displays the WLAN summary list. Example: admin(network.lan.
8-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide admin(network.lan.wlan-mapping)>show wlan Warning: This will display secure information, Do you want to continue? (n/y?)y WLAN1: WLAN Name :WLAN1 ESSID :101 Radio Bands :2.4 and 5.0 GHz VLAN : Security Policy :Default QoS Policy :Default Rate Limiting :disabled For information on displaying the VLAN screens using the applet (GUI), see Configuring VLAN Support on page 5-5.
CLI Reference AP7131N>admin(network.lan.wlan-mapping)> set Description: Sets VLAN parameters for the access point. Syntax: set mgmt- tag native-tag mode Defines the Management VLAN tag index (1 or 2) to tag number (1-4095). Sets the Native VLAN tag index (1 or 2) to tag number (1-4095). Sets WLAN VLAN mode (WLAN 1-16) to either dynamic or static. Example: admin(network.lan.wlan-mapping)>set mgmt-tag 1 10 admin(network.lan.wlan-mapping)>set native-tag 1 12 admin(network.lan.
8-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.wlan-mapping)> create Description: Creates a VLAN for the access point. Syntax: create vlan-id vlan-name Defines the VLAN ID (1-4095). Specifies the name of the VLAN (1-31 characters in length). Example: admin(network.lan.wlan-mapping)> admin(network.lan.wlan-mapping)>create 5 vlan-5 For information on creating VLANs using the applet (GUI), see Configuring VLAN Support on page 5-5.
CLI Reference AP7131N>admin(network.lan.wlan-mapping)> edit Description: Modifies a VLAN’s name and ID. Syntax: edit name id Modifies an exisiting VLAN name (1-31 characters in length) Modifies an existing VLAN ID (1-4095) characters in length) For information on editing VLANs using the applet (GUI), see Configuring VLAN Support on page 5-5.
8-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.wlan-mapping)> delete Description: Deletes a specific VLAN or all VLANs. Syntax: delete < VLAN id> Deletes a specific VLAN ID (1-16). all Deletes all defined VLAN entries. For information on deleting VLANs using the applet (GUI), see Configuring VLAN Support on page 5-5.
CLI Reference AP7131N>admin(network.lan.wlan-mapping)> lan-map Description: Maps an access point VLAN to a WLAN. Syntax: lan-map Maps an existing WLAN to an enabled LAN. All names and IDs are case-sensitive. Defines enabled LAN name. All names and IDs are case-sensitive. admin(network.lan.wlan-mapping)>lan-map wlan1 lan1 For information on mapping VLANs using the applet (GUI), see Configuring VLAN Support on page 5-5.
8-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.wlan-mapping)> vlan-map Description: Maps an access point VLAN to a WLAN. Syntax: vlan-map Maps an existing WLAN to an enabled LAN. All names and IDs are case-sensitive. Defines the existing VLAN name. All names and IDs are case-sensitive. admin(network.lan.
CLI Reference 8.3.1.3 Network LAN, DHCP Commands AP7131N>admin(network.lan.dhcp)> Description: Displays the access point DHCP submenu. The items available are displayed below. show set add delete list .. / save quit Displays DHCP parameters. Sets DHCP parameters. Adds static DHCP address assignments. Deletes static DHCP address assignments. Lists static DHCP address assignments. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI and exits the session.
8-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.dhcp)> show Description: Shows DHCP parameter settings. Syntax: show Displays DHCP parameter settings for the access point. These parameters are defined with the set command. Example: admin(network.lan.dhcp)>show **LAN1 DHCP Information** DHCP Address Assignment Range: Starting IP Address Ending IP Address Lease Time : 192.168.0.100 : 192.168.0.
CLI Reference 8-31 AP7131N>admin(network.lan.dhcp)> set Description: Sets DHCP parameters for the LAN port. Syntax: set range lease Sets the DHCP assignment range from IP address to IP address for the specified LAN (1-lan1, 2-lan2). Sets the DHCP lease time in seconds (120-999999) for the specified LAN. Example: admin(network.lan.dhcp)>set range 1 192.168.0.100 192.168.0.254 admin(network.lan.dhcp)>set lease 1 86400 admin(network.lan.
8-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.dhcp)> add Description: Adds static DHCP address assignments. Syntax: add Adds a reserved static IP address to a MAC address for the specified LAN Example: admin(network.lan.dhcp)>add 1 00A0F8112233 192.160.24.6 admin(network.lan.dhcp)>add 1 00A0F1112234 192.169.24.7 admin(network.lan.
CLI Reference AP7131N>admin(network.lan.dhcp)> delete Description: Deletes static DHCP address assignments. Syntax: delete all Deletes the static DHCP address entry (1-30) for the specified LAN. Deletes all static DHCP addresses. Example: admin(network.lan.dhcp)>list 1 ----------------------------------------------------------------------------Index MAC Address IP Address ----------------------------------------------------------------------------1 00A0F8112233 10.1.2.
8-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.dhcp)> list Description: Lists static DHCP address assignments. Syntax: list Lists the static DHCP address assignments for the specified LAN (1-LAN1, 2 LAN2). Example: admin(network.lan.
CLI Reference 8.3.1.4 Network Type Filter Commands AP7131N>admin(network.lan.type-filter)> Description: Displays the access point Type Filter submenu. The items available under this command include: show set add delete .. / save quit Displays the current Ethernet Type exception list. Defines Ethernet Type Filter parameters. Adds an Ethernet Type Filter entry. Removes an Ethernet Type Filter entry. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.type-filter)> show Description: Displays the access point’s current Ethernet Type Filter configuration. Syntax: show Displays the existing Type-Filter configuration for the specified LAN. Example: admin(network.lan.
CLI Reference 8-37 AP7131N>admin(network.lan.type-filter)> set Description: Defines the access point Ethernet Type Filter configuration. Syntax: set mode allow or deny Allows or denies the access point from processing a specified Ethernet data type for the specified LAN. Example: admin(network.lan.type-filter)>set mode 1 allow For information on configuring the type filter settings using the applet (GUI), see Setting the Type Filter Configuration on page 5-14.
8-38 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.lan.type-filter)> add Description: Adds an Ethernet Type Filter entry. Syntax: add Adds entered Ethernet Type to list of data types either allowed or denied access point processing permissions for the specified LAN (either LAN1 or LAN2). Example: admin(network.lan.type-filter)> admin(network.wireless.type-filter)>add 1 8137 admin(network.wireless.type-filter)>add 2 0806 admin(network.
CLI Reference 8-39 AP7131N>admin(network.lan.type-filter)> delete Description: Removes an Ethernet Type Filter entry individually or the entire Type Filter list. Syntax: delete all Deletes the specified Ethernet Type index entry (1 through 16). Deletes all Ethernet entries currently in list. Example: admin(network.lan.type-filter)>delete 1 1 admin(network.lan.
8-40 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.2 Network WAN Commands AP7131N>admin(network.wan)> Description: Displays the WAN submenu. The items available under this command are shown below. show set nat vpn content dyndns .. / save quit Displays the access point WAN configuration and the access point’s current PPPoE configuration. Defines the access point’s WAN and PPPoE configuration. Displays the NAT submenu, wherein Network Address Translations (NAT) can be defined.
CLI Reference AP7131N>admin(network.wan)> show Description: Displays the access point WAN port parameters. Syntax: show Shows the general IP parameters for the WAN port along with settings for the WAN interface. Example: admin(network.wan)>show Warning: This will display secure information, Do you want to continue? (n/y?)y Status : enable WAN DHCP Client Mode : disable IP Address : 10.1.1.1 Network Mask : 255.0.0.0 Default Gateway : 0.0.0.0 Primary DNS Server : 0.0.0.
8-42 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan)> set Description: Defines the configuration of the access point WAN port. Syntax: set wan dhcp ipadr enable/disable enable/disable mask dgw dns
CLI Reference 8.3.2.1 Network WAN NAT Commands AP7131N>admin(network.wan.nat)> Description: Displays the NAT submenu. The items available under this command are shown below. show set add delete list .. / save quit Displays the access point’s current NAT parameters for the specified index. Defines the access point NAT settings. Adds NAT entries. Deletes NAT entries. Lists NAT entries. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-44 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.nat)> show Description: Displays access point NAT parameters. Syntax: show Displays access point NAT parameters for the specified NAT index (1-8). Example: admin(network.wan.nat)>show 2 WAN IP Mode : enable WAN IP Address : 157.235.91.2 NAT Type : 1-to-many Inbound Mappings : Port Forwarding unspecified port forwarding mode : enable unspecified port fwd. ip address : 111.223.222.
CLI Reference 8-45 AP7131N>admin(network.wan.nat)> set Description: Sets NAT inbound and outbound parameters. Syntax: set type ip inb outb
8-46 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.nat)> add Description: Adds NAT entries.
CLI Reference 8-47 AP7131N>admin(network.wan.nat)> delete Description: Deletes NAT entries. Syntax: delete all Deletes a specified NAT index entry associated with the WAN. Deletes all NAT entries associated with the WAN. Example: admin(network.wan.
8-48 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.nat)> list Description: Lists access point NAT entries for the specified index. Syntax: list Lists the inbound NAT entries associated with the WAN index (1-8). Example: admin(network.wan.
CLI Reference 8.3.2.2 Network WAN, VPN Commands AP7131N>admin(network.wan.vpn)> Description: Displays the VPN submenu. The items available under this command include: add set delete list reset stats ikestate .. / save quit Adds VPN tunnel entries. Sets key exchange parameters. Deletes VPN tunnel entries. Lists VPN tunnel entries Resets all VPN tunnels. Lists security association status for the VPN tunnels. Displays an Internet Key Exchange (IKE) summary. Goes to the parent menu. Goes to the root menu.
8-50 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.vpn)> add Description: Adds a VPN tunnel entry. Syntax: add Creates a tunnel (1 to 13 characters) to gain access through local WAN IP from the remote subnet with address and subnet mask using the remote gateway . Example: admin(network.wan.vpn)>add 2 SJSharkey 209.235.44.31 206.107.22.
CLI Reference AP7131N>admin(network.wan.vpn)> set Description: Sets VPN entry parameters. Syntax: set type Sets the tunnel type to Auto or Manual for the specified tunnel name. authalgo Sets the authentication algorithm for to SHA1. authkey Sets the AH authentication key (if type is Manual) for tunnel with the direction set to IN or OUT, and the manual authentication key set to .
8-52 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide ike opmode Sets the Operation Mode of IKE for to Main or Aggr(essive). myidtype Sets the Local ID type for IKE authentication for (1 to 13 characters) to (IP, FQDN, or UFQDN). remidtype Sets the Remote ID type for IKE authentication for (1 to 13 characters) to (IP, FQDN, or UFQDN).
CLI Reference AP7131N>admin(network.wan.vpn)> delete Description: Deletes VPN tunnel entries. Syntax: delete all Deletes all VPN entries. Deletes VPN entries . Example: admin(network.wan.vpn)>list -------------------------------------------------------------------------Tunnel Name Type Remote IP/Mask Remote Gateway Local WAN IP -------------------------------------------------------------------------Eng2EngAnnex Manual 192.168.32.2/24 192.168.33.1 192.168.24.
8-54 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.vpn)> list Description: Lists VPN tunnel entries. Syntax: list Lists all tunnel entries. Lists detailed information about tunnel named . The must match case with the name of the VPN tunnel entry. Example: admin(network.wan.
CLI Reference AP7131N>admin(network.wan.vpn)> reset Description: Resets all of the access point’s VPN tunnels. Syntax: reset Resets all VPN tunnel states. Example: admin(network.wan.vpn)>reset VPN tunnels reset. admin(network.wan.vpn)> For information on configuring VPN using the applet (GUI), see Configuring VPN Tunnels on page 6-22.
8-56 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.vpn)> stats Description: Lists statistics for all active tunnels. Syntax: stats Display statistics for all VPN tunnels. Example: admin(network.wan.
CLI Reference 8-57 AP7131N>admin(network.wan.vpn)> ikestate Description: Displays statistics for all active tunnels using Internet Key Exchange (IKE). Syntax: ikestate Displays status about Internet Key Exchange (IKE) for all tunnels. In particular, the table indicates whether IKE is connected for any of the tunnels, it provides the destination IP address, and the remaining lifetime of the IKE key. Example: admin(network.wan.
8-58 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.content)> Description: Displays the Outbound Content Filtering menu. The items available under this command include: addcmd delcmd list .. / save quit Adds control commands to block outbound traffic. Deletes control commands to block outbound traffic. Lists application control commands. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
CLI Reference AP7131N>admin(network.wan.content)> addcmd Description: Adds control commands to block outbound traffic. Syntax: addcmd web proxy activex file smtp helo mail rcpt data quit send saml reset vrfy expn ftp put get ls mkdir cd pasv Adds WEB commands to block outbound traffic. Adds a Web proxy command. Adds activex files. Adds Web URL extensions (10 files maximum). The filename should be 1-15 characters. Adds SMTP commands to block outbound traffic.
8-60 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.content)> delcmd Description: Deletes control commands to block outbound traffic. Syntax: delcmd web proxy activex file smtp helo mail rcpt data quit send saml reset vrfy expn ftp put get ls mkdir cd pasv Deletes WEB commands to block outbound traffic. Deletes a Web proxy command. Deletes activex files. Deletes Web URL extensions (10 files maximum) Deletes SMTP commands to block outbound traffic.
CLI Reference AP7131N>admin(network.wan.content)> list Description: Lists application control commands. Syntax: list web smtp ftp Lists WEB application control record. Lists SMTP application control record. Lists FTP application control record. Example: admin(network.wan.content)>list web HTTP Files/Commands Web Proxy : deny ActiveX : allow filename : admin(network.wan.
8-62 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.2.3 Network WAN, Dynamic DNS Commands AP7131N>admin(network.wan.dyndns)> Description: Displays the Dynamic DNS submenu. The items available under this command include: set update show .. / save quit Sets Dynamic DNS parameters. Sets key exchange parameters. Shows the Dynamic DNS configuration. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
CLI Reference AP7131N>admin(network.wan.dyndns)> set Description: Sets the access point’s Dynamic DNS configuration. Syntax: set mode username password hostname enable/disable Enables or disbales the Dynamic DNS service for the access point. Enter a 1 - 32 character username for the account used for the access point. Enter a 1 - 32 character password for the account used for the access point. Enter a 1 - 32 character hostname for the account used for the access point.
8-64 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wan.dyndns)> update Description: Updates the access point’s current WAN IP address with the DynDNS service. Syntax: update Updates the access point’s current WAN IP address with the DynDNS service. Example: admin(network.wan.dyndns)>update IP Address : 157.235.91.
CLI Reference AP7131N>admin(network.wan.dyndns)> show Description: Shows the current Dynamic DNS configuration. Syntax: show Shows the access point’s current Dynamic DNS configuration. Example: admin(network.wan.dyndns)>show Warning: This will display secure information, Do you want to continue? (n/y?)y DynDNS Configuration Mode : enable Username : percival Password : ******** Hostname : greengiant DynDNS Update Response IP Address : 157.235.91.
8-66 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3 Network Wireless Commands AP7131N>admin(network.wireless) Description: Displays the access point wireless submenu. The items available under this command include: wlan security Displays the WLAN submenu used to create and configure up to 16 WLANs per access point. Displays the security submenu used to create encryption and authentication based security policies for use with access point WLANs.
CLI Reference 8-67 8.3.3.1 Network WLAN Commands AP7131N>admin(network.wireless.wlan)> Description: Displays the access point wireless LAN (WLAN) submenu. The items available under this command include: show create edit delete hotspot ipfpolicy .. / save quit Displays the access point’s current WLAN configuration. Defines the parameters of a new WLAN. Modifies the properties of an existing WLAN. Deletes an existing WLAN. Displays the WLAN hotspot menu. Goes to the WLAN IP Filter Policy menu.
8-68 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wlan)> show Description: Displays the access point’s current WLAN configuration. Syntax: show summary wlan Displays the current configuration for existing WLANs. Displays the configuration for the requested WLAN (WLAN 1 through 16). Example: admin(network.wireless.
CLI Reference AP7131N>admin(network.wireless.wlan)> create Description: Defines the parameters of a new WLAN. Syntax: create show set wlan security acl qos ess wlan-name 5.0GHz 2.4Ghz mesh hotspot max-mu idle- timeout security acl no-mu-mu sbeacon bcast qos rate-limiting limit w2wl limit wl2w add-wlan Displays newly created WLAN and policy number. Displays security policy summary. Displays MU ACL policy summary. Displays QoS policy summary. Defines the ESSID for a target WLAN.
8-70 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide QoS Policy : Default per-mu rate limiting : disabled per-mu rate limit (wired-to-wl) : 1000 kb per-mu rate limit (wl-to-wired) : 1000 kb admin(network.wireless.wlan.
CLI Reference AP7131N>admin(network.wireless.wlan)> edit Description: Edits the properties of an existing WLAN policy. Syntax: edit Edits the properties of an existing (and specified) WLAN policy (1 -16). For information on editing a WLAN using the applet (GUI), see Creating/Editing Individual WLANs on page 5-29.
8-72 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wlan)> delete Description: Deletes an existing WLAN. Syntax: delete Deletes a target WLAN using the name supplied. all Deletes all WLANs defined (except default WLAN). Example admin(network.wireless.wlan)>delete all admin(network.wireless.wlan)> For information on deleting a WLAN using the applet (GUI), see Creating/Editing Individual WLANs on page 5-29.
CLI Reference 8-73 AP7131N>admin(network.wireless.wlan.hotspot)> Description: Displays the Hotspot submenu. The items available under this command include: show redirection radius white-list save quit .. / Show hotspot parameters. Goes to the hotspot redirection menu. Goes to the hotspot Radius menu. Goes to the hotspot white-list menu. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu.
8-74 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wlan.hotspot)> show Description: Displays the current access point Rogue AP detection configuration. Syntax: show hotspot Shows hotspot parameters per wlan index (1-16). Example: admin(network.wireless.wlan.
CLI Reference 8-75 AP7131N>admin(network.wireless.wlan.hotspot)> redirection Description: Goes to the hotspot redirection menu. Syntax: redirection set show save quit .. / Sets the hotspot http-re-direction by index (1-16) for the specified URL. Shows hotspot http-redirection details for specifiec index (1-16) for specified page (login, welcome, fail) and target URL.. Shows hotspot http-redirection details. Saves the updated hotspot configuration to flash memory.
8-76 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wlan.hotspot)> radius Description: Goes to the hotspot Radius menu. Syntax: set show save quit .. / Sets the Radius hotspot configuration. Shows Radius hotspot server details. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu.
CLI Reference 8-77 AP7131N>admin(network.wireless.wlan.hotspot.radius)> set Description: Sets the Radius hotspot configuration. Syntax: set server Sets the Radius hotpost server IP address per wlan index (1-16) secret acct-mode acct-server Sets the Radius hotspot server shared secret password.
8-78 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wlan.hotspot.radius)> show Description: Shows Radius hotspot server details. Syntax: show radius Displays Radius hotspot server details per index (1-16) Example: admin(network.wireless.wlan.hotspot.radius)>show radius 1 Warning: This will display secure information, Do you want to continue? (n/y?)y WLAN 1 Hotspot Mode : enable Primary Server Ip adr : 157.235.12.
CLI Reference 8-79 AP7131N>admin(network.wireless.wlan.hotspot)> white-list Description: Goes to the hotspot white-list menu. Syntax: white-list add clear show save quit .. / Adds hotspot whitelist rules by index (1-16) for specified IP address. Clears hotspot whitelist rules for specified index (1-16). Shows hotspot whitelist rules for specified index (1-16). Saves the updated hotspot configuration to flash memory. Quits the CLI session. Goes to the parent menu. Goes to the root menu.
8-80 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3.2 Network Security Commands AP7131N>admin(network.wireless.security)> Description: Displays the access point wireless security submenu. The items available under this command include: show create edit delete .. / save quit Displays the access point’s current security configuration. Creates a security policy. Edits the properties of an existing security policy. Removes a specific security policy. Goes to the parent menu.
CLI Reference AP7131N>admin(network.wireless.security)>show Description: Displays the access point’s current security configuration. Syntax: show summary policy Displays list of existing security policies (1-16). Displays the specified security policy . Example: admin(network.wireless.
8-82 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide eap mu retries : 2 (1-10) retries. eap server timeout : 5 (1-255) seconds. eap server retries : 2 (1-255) retries. Encryption type : WPA2/CCMP (802.11i) ccmp broadcast key rotate mode : disable 802.11i ccmp preauthentication : disable WPA2 PTK timeout : 2 admin(network.wireless.security)> Related Commands: create Defines security parameters for the specified WLAN.
CLI Reference 8-83 AP7131N>admin(network.wireless.security)>create Description: Defines the parameter of access point security policies. Syntax: create Defines the parameters of a security policy. show set Displays new or existing security policy parameters. sec-name Sets the name of the security policy. auth Sets the authentication type for WLAN to (none or eap) eap server Sets the radius server (1-primary or as 2secondary) IP address .
8-84 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide adv add-policy retry Sets the maximum number of MU retries to (1-10). syslog Enable or disable syslog messages. ip Defines syslog server IP address. mu-quiet
CLI Reference .. 8-85 Disregards the policy creation and exits the CLI session. For information on configuring the encryption and authentication options available to the access point using the applet (GUI), see Configuring Security Options on page 6-2.
8-86 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.security)>edit Description: Edits the properties of a specific security policy. Syntax: set Edits security policy parameters. The values subject to modification, are the same ones created using the AP7131N>admin(network.wireless.security)>create command. show Displays security policy parameters change Completes policy edit and exit .. Cancels the edit and exit Example: admin(network.
CLI Reference AP7131N>admin(network.wireless.security)> delete Description: Deletes a specific security policy. Syntax: delete Removes the specified security policy from the list of supported policies. Removes all security policies except the default policy. Example admin(network.wireless.security)>delete all Deleting all of your security policies... Note that all WLANs will be assigned the default security policy. admin(network.wireless.
8-88 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3.3 Network ACL Commands AP7131N>admin(network.wireless.acl)> Description: Displays the access point Mobile Unit Access Control List (ACL) submenu. The items available under this command include: show create edit delete .. / save quit Displays the access point’s current ACL configuration. Creates an MU ACL policy. Edits the properties of an existing MU ACL policy. Removes an MU ACL policy. Goes to the parent menu.
CLI Reference 8-89 AP7131N>admin(network.wireless.acl)> show Description: Displays the access point’s current ACL configuration. Syntax: show summary policy Displays the list of existing MU ACL policies. Displays the requested MU ACL index policy. Example: admin(network.wireless.
8-90 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.acl)> create Description: Creates an MU ACL policy. Syntax: create show set add-addr delete add-policy .. acl-name mode Displays the parameters of a new ACL policy. Sets the MU ACL policy name. Sets the ACL mode for the defined index (1-16). Allowed MUs can access the access point managed LAN. Options are deny and allow.
CLI Reference 8-91 AP7131N>admin(network.wireless.acl.edit)> Description: Edits the properties of an existing MU ACL policy. Syntax: show set add-addr delete change .. Displays MU ACL policy and its parameters. Modifies the properties of an existing MU ACL policy. Adds an MU ACL table entry. Deletes an MU ACL table entry, including starting and ending MAC address ranges. Completes the changes made and exits the session. Cancels the changes made and exits the session.
8-92 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.acl)> delete Description: Removes an MU ACL policy. Syntax: delete all Deletes a partilcular MU ACL policy index. Deletes all MU ACL policies. For information on configuring the ACL options available to the access point using the applet (GUI), see Configuring a WLAN Access Control List (ACL) on page 5-35.
CLI Reference 8.3.3.4 Network Radio Configuration Commands AP7131N>admin(network.wireless.radio)> Description: Displays the access point Radio submenu. The items available under this command include: show set radio1 radio2 .. / save quit Summarizes access point radio parameters at a high-level. Defines the access point radio configuration. Displays the 2.4 GHz radio submenu. Displays the 5.0 GHz radio submenu. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash.
8-94 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio)> show Description: Displays the access point’s current radio configuration. Syntax: show Displays the access point’s current radio configuration.Displays whether sensor-only mode status is enabled/ displayed also. Example: admin(network.wireless.
CLI Reference 8-95 DSCP QOS Mappings: DSCP value 2 : Wireless Traffic ID (WMM AC) 0 1 3 4 5 6 7 : 0 (best-effort) 8 9 10 11 12 13 14 15 : 1 (background) 16 17 18 19 20 21 22 23 : 2 (background) 24 25 26 27 28 29 30 31 : 3 (best-effort) 32 33 34 35 36 37 38 39 : 4 (video) 40 41 42 43 44 45 46 47 : 5 (video) 48 49 50 51 52 53 54 55 : 6 (voice) 56 57 58 59 60 61 62 63 : 7 (voice) admin(network.wireless.
8-96 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio)> set Description: Sets the access point’s radio configuration and defines the RF band of operation. Syntax: set radio-config sensor-only max-mus mesh-base mesh-max mesh-client mesh-roaming-client mesh-timeout mesh-wlan dot11-auth qos-mapping (wired-to-wireless) Sets the radio configuration. Sets sensor only mode as enabled/disabled.
CLI Reference Radio1 Name : Radio1 Radio Mode : enable Radio2 Name : Radio2 Radio Mode : enable admin(network.wireless.radio)> admin(network.wireless.radio)>set max-mus 127 admin(network.wireless.radio)>set mesh-base 1 enable admin(network.wireless.radio)>set mesh-max 1 11 admin(network.wireless.radio)>set mesh-client 1 disable admin(network.wireless.radio)>set mesh-roaming-client 1 enable admin(network.wireless.radio)>set mesh-wlan wlan1 admin(network.wireless.
8-98 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz])> Description: Displays a specific 802.11n 2.4 GHz radio 1 submenu. The items available under this command include: Syntax: show set advanced mesh .. / save quit Displays 802.11n (2.4 GHz) radio settings. Defines specific 802.11n (2.4 GHz) radio parameters. Displays the Adavanced radio settings submenu. Goes to the Wireless AP Connections submenu. Goes to the parent menu.
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz])>show Description: Displays specific 802.11n (2.4 GHz) radio settings. Syntax: show radio rates aggr qos Displays specific 802.11n (2.4 GHz) radio settings. Displays specific 802.11n (2.4 GHz) radio rate settings. Displays specific 802.11n (2.4 GHz) aggregation settings. Displays specific 802.11n (2.4 GHz) radio WMM QoS settings. Example: admin(network.wireless.radio.802-11n[2.
8-100 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide admin(network.wireless.radio.802-11n[2.4 GHz])>show rates Basic Rates 1 2 5.5 11 Supported Rates 1 2 5.5 6 9 11 12 18 24 36 48 54 Short Guard Interval disable ----------------------------------------------------------------------------MCS Index Basic/Supported 20 MHz Rate 40 MHz Rate ----------------------------------------------------------------------------0 Supported 6.5 Mbps 13.5 Mbps 1 Supported 13.0 Mbps 27.
CLI Reference 8-101 admin(network.wireless.radio.802-11n[2.4 GHz])>show qos Radio QOS Parameter Set 11n-default ----------------------------------------------------------------------------Access Category CWMin CWMax AIFSN TXOPs (32 usec) TXOPs ms ----------------------------------------------------------------------------Background 15 1023 7 0 0.000 Best Effort 15 63 3 31 0.992 Video 7 15 1 94 3.008 Voice 3 7 1 47 1.
8-102 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz])> set Description: Defines specific 802.11n (2.4 GHz) radio parameters. Syntax: set placement ch-mode channel power rf-mode Defines the access point radio placement as indoors or outdoors. Determines how the radio channel is selected (user, auto-20 or auto-40). Defines the radio channel used. Channel allowed depends on actual country of operation.
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].advanced)> Description: Displays the advanced submenu for the 802.11n (2.4 GHz) radio. The items available under this command include: Syntax: show set .. / save quit Displays advanced radio settings for the 802.11n (2.4 GHz) radio. Defines advanced parameters for the 802.11n (2.4 GHz) radio. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-104 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].advanced)> show Description: Displays the BSSID to WLAN mapping for the 802.11n (2.4 GHz) radio. Syntax: show advanced wlan Displays advanced settings for the 802.11n (2.4 GHz) radio. Displays WLAN summary list for the 802.11n (2.4 GHz) radio. Example: admin(network.wireless.radio.802-11n[2.4 GHz].
CLI Reference 8-105 AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].advanced)> set Description: Defines advanced parameters for the target 802.11n (2.4 GHz) radio. Syntax: set wlan bss Defines advanced WLAN to BSSID mapping for the target radio. Sets the BSSID to primary WLAN definition. Example: admin(network.wireless.radio.802-11n[2.4 GHz].advanced)>set wlan demoroom 1 admin(network.wireless.radio.802-11n[2.4 GHz].
8-106 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].mesh)> Description: Displays the mesh configuration submenu for the 802.11n (2.4 GHz) radio. The items available under this command include: Syntax: show set add delete .. / save quit Displays mesh settings and status for the 802.11n (2.4 GHz) radio. Defines mesh parameters for the 802.11n (2.4 GHz) radio. Adds a 802.11n (2.4 GHz) radio mesh connection. Deletes a 802.11n (2.
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].mesh)> show Description: Displays mesh settings and status for the 802.11n (2.4 GHz) radio. Syntax: show config status Displays the connection list configuration. Shows the available mesh connection status. Example: admin(network.wireless.radio.802-11n[2.4 GHz].mesh)>show config Mesh Connection Auto Select : enable admin(network.wireless.radio.802-11n[2.4 GHz].
8-108 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].mesh)> set Description: Defines mesh parameters for the 802.11n (2.4 GHz) radio. Syntax: set Enables or disables auto select mesh connections. Example: admin(network.wireless.radio.802-11n[2.4 GHz].mesh)>set auto-select enable admin(network.wireless.radio.802-11n[2.4 GHz].
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].mesh)> add Description: Adds a 802.11n (2.4 GHz) radio mesh connection. Syntax: add Defines the connection priority (1-16). Sets the access point MAC address. Example: admin(network.wireless.radio.802-11n[2.4 GHz].
8-110 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[2.4 GHz].mesh)> delete Description: Deletes a 802.11n (2.4 GHz) radio mesh connection by specified index or by removing all entries. Syntax: delete Deletes a mesh connection by specified index (1-16). Removes all mesh connections. Example: admin(network.wireless.radio.802-11n[2.4 GHz].
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz])> Description: Displays a specific 802.11n (5.0 GHz) radio 2 submenu. The items available under this command include: Syntax: show set advanced mesh .. / save quit Displays 802.11n (5.0 GHz) radio settings Defines specific 802.11n (5.0 GHz) radio parameters. Displays the Advanced radio settings submenu. Goes to the Mesh Connections submenu. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash.
8-112 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz])> show Description: Displays specific 802.11n (5.0 GHz) radio settings. Syntax: show radio rates aggr qos Displays specific 802.11n (5.0 GHz) radio settings. Displays specific 802.11n (5.0 GHz) radio rate settings. Displays specific 802.11n (5.0 GHz) aggregation settings. Displays specific 802.11n (5.0 GHz) radio WMM QoS settings. Example: admin(network.wireless.radio.
CLI Reference admin(network.wireless.radio.802-11n[5.0 GHz])>show rates Basic Rates 6 12 24 Supported Rates 6 9 12 18 24 36 48 54 Short Guard Interval disable ----------------------------------------------------------------------------MCS Index Basic/Supported 20 MHz Rate 40 MHz Rate ----------------------------------------------------------------------------0 Supported 6.5 Mbps 13.5 Mbps 1 Supported 13.0 Mbps 27.0 Mbps 2 Supported 19.5 Mbps 40.5 Mbps 3 Supported 26.0 Mbps 54.
8-114 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide admin(network.wireless.radio.802-11n[5.0 GHz])>show qos Radio QOS Parameter Set 11n-default ----------------------------------------------------------------------------Access Category CWMin CWMax AIFSN TXOPs (32 usec) TXOPs ms ----------------------------------------------------------------------------Background 15 1023 7 0 0.000 Best Effort 15 63 3 31 0.992 Video 7 15 1 94 3.008 Voice 3 7 1 47 1.
CLI Reference 8-115 AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz])> set Description: Defines specific 802.11n (5.0 GHz) radio parameters. Syntax: set placement ch-mode channel power rf-mode rates beacon dtim aggr shortgi rts range qos qbss-beacon qbss-mode single-antenna Defines the access point radio placement as indoors or outdoors. Determines how the radio channel is selected. Defines the actual channel used by the radio. Channel allowed depends on actual country of operation.
8-116 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].advanced)> Description: Displays the advanced submenu for the 802.11n (5.0 GHz) radio. The items available under this command include: Syntax: show set .. / save quit Displays advanced radio settings for the 802.11n (5.0 GHz) radio. Defines advanced parameters for the 802.11n (5.0 GHz) radio. Goes to the parent menu. Goes to the root menu.
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].advanced)> show Description: Displays the BSSID to WLAN mapping for the 802.11n (5.0 GHz) radio. Syntax: show advanced wlan Displays advanced settings for the 802.11n (5.0 GHz) radio. Displays WLAN summary list for 802.11n (5.0 GHz) radio. Example: admin(network.wireless.radio.802-11n[5.0 GHz].
8-118 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].advanced)> set Description: Defines advanced parameters for the target 802.11n (5.0 GHz) radio. Syntax: set wlan bss Defines advanced WLAN to BSSID mapping for the target 5.0 GHz radio. Sets the BSSID to primary WLAN definition. Example: admin(network.wireless.radio.802-11n[5.0 GHz].advanced)>set wlan demoroom 1 admin(network.
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].mesh)> Description: Displays the mesh configuration submenu for the 802.11n (5.0 GHz) radio. The items available under this command include: Syntax: show set add delete .. / save quit Displays mesh settings and status for the 802.11n (5.0 GHz) radio. Defines mesh parameters for the 802.11n (5.0 GHz) radio. Adds a 802.11n (5.0 GHz) radio mesh connection. Deletes a 802.11n (5.0 GHz) radio mesh connection. Goes to the parent menu.
8-120 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].mesh)> show Description: Displays mesh settings and status for the 802.11n (5.0 GHz) radio. Syntax: show config status Displays the connection list configuration. Shows the available mesh connection status. Example: admin(network.wireless.radio.802-11n[5.0 GHz].mesh)>show config Mesh Connection Auto Select : enable admin(network.wireless.radio.802-11n[5.0 GHz].
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].mesh)> set Description: Defines mesh parameters for the 802.11n (5.0 GHz) radio. Syntax: set Enables or disables auto select mesh connections. Example: admin(network.wireless.radio.802-11n[5.0 GHz].mesh)>set auto-select enable admin(network.wireless.radio.802-11n[5.0 GHz].
8-122 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].mesh)> add Description: Adds a 802.11n (5.0 GHz) radio mesh connection. Syntax: add Defines the connection priority (1-16). Sets the access point MAC address. Example: admin(network.wireless.radio.802-11n[5.0 GHz].
CLI Reference AP7131N>admin(network.wireless.radio.802-11n[5.0 GHz].mesh)> delete Description: Deletes a 802.11n (5.0 GHz) radio mesh connection by specified index or by removing all entries. Syntax: delete Deletes a mesh connection by specified index (1-16). Removes all mesh connections. Example: admin(network.wireless.radio.802-11n[5.0 GHz].
8-124 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3.5 Network Quality of Service (QoS) Commands AP7131N>admin(network.wireless.qos)> Description: Displays the access point Quality of Service (QoS) submenu. The items available under this command include: show create edit delete .. / save quit Displays access point QoS policy information. Defines the parameters of the QoS policy. Edits the settings of an existing QoS policy. Removes an existing QoS policy.
CLI Reference 8-125 AP7131N>admin(network.wireless.qos)> show Description: Displays the access point’s current QoS policy by summary or individual policy. Syntax: show summary policy Displays all exisiting QoS policies that have been defined. Displays the configuration for the requested QoS policy. Example: admin(network.wireless.
8-126 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.qos.create)> Description: Defines an access point QoS policy. Syntax: show set qos-name vop mcast wmm-qos param-set cwmin cwmax aifsn txops default add-policy .. Displays QoS policy parameters.
CLI Reference 8-127 AP7131N>admin(network.wireless.qos.edit)> Descripton: Edits the properties of an existing QoS policy. Syntax: show set qos-name vop mcast wmm-qos param-set cwmin cwmax aifsn txops default Displays QoS policy parameters. Sets the QoS name for the specified index entry. Enables or disables support (by index) for legacy VOIP devices.
8-128 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.qos)> delete Description: Removes a QoS policy. Syntax: delete Deletes the specified QoS polciy index, or all of the policies (except default policy). For information on configuring the WLAN QoS options available to the access point using the applet (GUI), see Setting the WLAN Quality of Service (QoS) Policy on page 5-39.
CLI Reference 8.3.3.6 Network Rate Limiting Commands AP7131N>admin(network.wireless.rate-limiting)> Description: Displays the access point Rate Limiting submenu. The items available under this command include: show set .. / save quit Displays Rate Limiting information for how data is processed by the access point. Defines Rate Limiting parameters for the access point. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-130 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.rate-limiting)> show Description: Displays the access point’s current Rate Limiting configuration. Syntax: show summary Displays the current Rate Limiting configuration for defined WLANs. wlan Example: admin(network.wireless.rate-limiting>show summary Per MU Rate Limiting : disable admin(network.wireless.
CLI Reference AP7131N>admin(network.wireless.rate-limiting)> set Description: Defines the access point Rate Limiting configuration. Syntax: set mode Enables or disables Rate Limiting. Example: admin(network.wireless.rate-limiting)>set mode enable admin(network.wireless.rate-limiting)> For information on configuring the Rate Limiting options available to the access point using the applet (GUI), see Configuring MU Rate Limiting on page 5-67.
8-132 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3.7 Network Rogue-AP Commands AP7131N>admin(network.wireless.rogue-ap)> Description: Displays the Rogue AP submenu. The items available under this command include: show set mu-scan allowed-list active-list rogue-list .. / save quit Displays the current access point Rogue AP detection configuration. Defines the Rogue AP detection method. Goes to the Rogue AP mu-uscan submenu. Goes to the Rogue AP Allowed List submenu.
CLI Reference 8-133 AP7131N>admin(network.wireless.rogue-ap)> show Description: Displays the current access point Rogue AP detection configuration. Syntax: show Displays the current access point Rogue AP detection configuration. Example: admin(network.wireless.
8-134 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.rogue-ap)> set Description: Defines the access point ACL rogue AP method. Syntax: set mu-scan interval on-channel detector-scan ABG-scan motorola-ap applst-ageout roglst-ageout Enables or disables to permit MUs to scan for rogue APs. Defines an interval for associated MUs to beacon in attempting to locate rogue APs.
CLI Reference AP7131N>admin(network.wireless.rogue-ap.mu-scan)> Description: Displays the Rogue-AP mu-scan submenu. Syntax: add show start .. / save quit Add all or just one scan result to Allowed AP list. Displays all APs located by the MU scan. Initiates scan immediately by the MU. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-136 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.rogue-ap.mu-scan)> start Description: Initiates an MU scan from a user provided MAC address. Syntax: start Initiates MU scan from user provided MAC address. Example: admin(network.wireless.rogue-ap.mu-scan)>start 00af8000001 admin(network.wireless.rogue-ap.
CLI Reference AP7131N>admin(network.wireless.rogue-ap.mu-scan)> show Description: Displays the results of an MU scan. Syntax: show Displays all APs located by the MU scan. Example: admin(network.wireless.rogue-ap.mu-scan)>show Scan Result Not Available. admin(network.wireless.rogue-ap.mu-scan)> For information on configuring the Rogue AP options available to the access point using the applet (GUI), see Configuring Rogue AP Detection on page 6-42.
8-138 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.rogue-ap.allowed-list)> Description: Displays the Rogue-AP allowed-list submenu. show add delete .. / save quit Displays the rogue AP allowed list Adds an AP MAC address and ESSID to the allowed list. Deletes an entry or all entries from the allowed list. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
CLI Reference 8-139 AP7131N>admin(network.wireless.rogue-ap.allowed-list)> show Description: Displays the Rogue AP allowed List. Syntax: show Displays the rogue-AP allowed list. Example: admin(network.wireless.rogue-ap.
8-140 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.rogue-ap.allowed-list)> add Description: Adds an AP MAC address and ESSID to existing allowed list. Syntax: add Adds an AP MAC address and ESSID to existing allowed list. “fffffffffffffffff” means any MAC Use a “*” for any ESSID. Example: admin(network.wireless.rogue-ap.allowed-list)>add 00A0F83161BB 103 admin(network.wireless.rogue-ap.
CLI Reference 8-141 AP7131N>admin(network.wireless.rogue-ap.allowed-list)> delete Description: Deletes an AP MAC address and ESSID to existing allowed list. Syntax: delete (1-50) Deletes an AP MAC address and ESSID (or all addresses) from the allowed list. Example: admin(network.wireless.rogue-ap.allowed-list)>delete 1 cfg read/write failed admin(network.wireless.rogue-ap.
8-142 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.3.8 WIPS Commands AP7131N>admin(network.wireless.wips)> Description: Displays the WIPS submenu. The items available under this command include: show set .. / save quit Displays the current WLAN Intrusion Prevention configuration. Sets WLAN Intrusion Prevention parameters. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
CLI Reference AP7131N>admin(network.wireless.wips)> show Description: Shows the WLAN Intrusion Prevention configuration. Syntax: show Displays the WLAN Intrusion Prevention configuration. Example: admin(network.wireless.wips>show Warning: This will display secure information, Do you want to continue? (n/y?)y WIPS Server #1 IP Address : 192.168.0.21 WIPS Server #2 IP Address : 10.1.1.1 admin(network.wireless.
8-144 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.wips)> set Description: Sets the WLAN Intrusion Prevention configuration. Syntax: set Defines the WLAN Intrusion Prevention Server IP Address (for server IPs 1 and 2). Example: admin(network.wireless.wips)>set server 1 192.168.0.21 admin(network.wireless.
CLI Reference 8.3.3.9 Network MU Locationing Commands AP7131N>admin(network.wireless.mu-locationing)> Description: Displays the MU Locationing submenu. The items available under this command include: show set .. / save quit Displays the current MU Locationing configuration. Defines MU Locationing parameters. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-146 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.wireless.mu-locationing> show Description: Displays the MU probe table configuration Syntax: show Displays the MU probe table configuration. Example: admin(network.wireless.mu-locationing)>show MU Probe Table Mode : disable MU Probe Table Size : 200 admin(network.wireless.
CLI Reference AP7131N>admin(network.wireless.mu-locationing> set Description: Defines the MU probe table configuration used for locating MUs. Syntax: set mode size Defines the MU probe table configuration. Enables/disables a mu probe scan. Defines the number of MUs in the table (the maximum allowed is 200). Example: admin(network.wireless.mu-locationing)>set admin(network.wireless.mu-locationing)>set mode enable admin(network.wireless.mu-locationing)>set size 200 admin(network.wireless.
8-148 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.3.4 Network Firewall Commands AP7131N>admin(network.firewall)> Description: Displays the access point firewall submenu. The items available under this command include: show set access advanced .. / save quit Displays the access point’s current firewall configuration. Defines the access point’s firewall parameters. Enables/disables firewall permissions through the LAN and WAN ports.
CLI Reference 8-149 AP7131N>admin(network.firewall)> show Description: Displays the access point firewall parameters. Syntax: show Shows all access point firewall settings. Example: admin(network.
8-150 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.firewall)> set Description: Defines the access point firewall parameters. Syntax: set nat-timeout syn src win ftp ip seq mime len hdr filter Defines the NAT timeout value. Enables or disables SYN flood attack check. Enables or disables source routing check. Enables or disables Winnuke attack check.
CLI Reference 8-151 AP7131N>admin(network.firewall)> access Description: Enables or disables firewall permissions through LAN to WAN ports. Syntax: show set add delete list .. / save quit Displays LAN to WAN access rules. Sets LAN to WAN access rules. Adds LAN to WAN exception rules. Deletes LAN to WAN access exception rules. Displays LAN to WAN access exception rules. for the specified LAN. Goes to parent menu Goes to root menu. Saves configuration to system flash. Quits and exits the CLI session.
8-152 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.firewall)> advanced Description: Displays whether an access point firewall rule is intended for inbound traffic to an interface or outbound traffic from that interface. Syntax: show set import inbound outbound .. / save quit Shows advanced subnet access parameters. Sets advanced subnet access parameters. Imports rules from subnet access. Goes to the Inbound Firewall Rules submenu.
CLI Reference 8.3.5 Network Router Commands AP7131N>admin(network.router)> Description: Displays the router submenu. The items available under this command are: show set add delete list .. / save quit Displays the existing access point router configuration. Sets the RIP parameters. Adds user-defined routes. Deletes user-defined routes. Lists user-defined routes. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-154 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.router)> show Description: Shows the access point route table. Syntax: show routes rips Shows the access point route table. Displays RIP parameters Example: admin(network.router)>show routes ---------------------------------------------------------------------------index destination netmask gateway interface metric ---------------------------------------------------------------------------1 192.168.2.
CLI Reference 8-155 AP7131N>admin(network.router)> set Description: Shows the access point route table. Syntax: set auth dir id key passwd type dgw-iface Sets the RIP authentication type (none, simple or MD5). Sets RIP direction (rx, tx or both) Sets MD5 authetication ID (1-256) for specific index (1-2). Sets MD5 authetication key (up to 16 characters) for specified inded (1-2). Sets the password (up to 16 characters) for simple authentication. Defines the RIP type (off, ripv1, ripv2, or ripv1v2).
8-156 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.router)> add Description: Adds user-defined routes. Syntax: add Adds a route with destination IP address , IP netmask , destination gateway IP address , interface LAN1, LAN2 or WAN , and metric set to (1-65535). Example: admin(network.router)>add 192.168.3.0 255.255.255.0 192.168.2.1 LAN1 1 admin(network.
CLI Reference 8-157 AP7131N>admin(network.router)> delete Description: Deletes user-defined routes. Syntax: delete all Deletes the user-defined route (1-20) from list. Deletes all user-defined routes. Example: admin(network.router)>list ---------------------------------------------------------------------------index destination netmask gateway interface metric ---------------------------------------------------------------------------1 192.168.2.0 255.255.255.0 192.168.0.1 lan1 1 2 192.
8-158 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(network.router)> list Description: Lists user-defined routes. Syntax: list Displays a list of user-defined routes. Example: admin(network.router)>list ---------------------------------------------------------------------------index destination netmask gateway interface metric ---------------------------------------------------------------------------1 192.168.2.0 255.255.255.0 192.168.0.1 lan1 1 2 192.168.1.0 255.
CLI Reference 8.4 System Commands AP7131N>admin(system)> Description: Displays the System submenu. The items available under this command are shown below. restart show set arp power-setup aap-setup access cmgr snmp userdb radius ntp logs config fw-update fips-test .. / save quit Restarts the access point. Shows access point system parameter settings. Defines access point system parameter settings. Dispalys the access point’s arp table. Goes to the Power Settings submenu.
8-160 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system)>restart Description: Restarts the access point access point. Syntax: restart Restarts the access point. Example: admin(system)>restart ********************************WARNING*********************************** ** Unsaved configuration changes will be lost when the access point is reset. ** Please be sure to save changes before resetting.
CLI Reference AP7131N>admin(system)>show Description: Displays high-level system information helpful to differentiate this access point. Syntax: show Displays access point system information. Example: admin(system)>show system name : AP-7131N system location : Atlanta Field Office admin email address : johndoe@mycompany.com system uptime : 0 days 4 hours 41 minutes AP-7131N firmware version : 4.0.2.
8-162 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system)>set Description: Sets access point system parameters. Syntax: set name loc email cc dns-relay- mode Sets the access point system name to (1 to 59 characters). The access point does not allow intermediate space characters between characters within the system name. For example, “AP7131N sales” must be changed to “AP7131Nsales” to be a valid system name.
CLI Reference AP7131N>admin(system)>arp Description: Dispalys the access point’s arp table. Example: admin(system)>arp IP Address HWtype HWaddress Flags Mask 157.235.92.210 ether 00:11:25:14:61:A8 C 157.235.92.179 ether 00:14:22:F3:D7:39 C 157.235.92.248 ether 00:11:25:B2:09:60 C 157.235.92.180 ether 00:0D:60:D0:06:90 C 157.235.92.3 ether 00:D0:2B:A0:D4:FC C 157.235.92.181 ether 00:15:C5:0C:19:27 C 157.235.92.80 ether 00:11:25:B2:0D:06 C 157.235.92.
8-164 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.1 Power Setup Commands AP7131N>admin(system)>power-setup Description: Displays the Power Setup submenu. show set .. / save quit Displays the current power setting configuration. Defines the access point’s power setting configuration. Goes to the parent menu. Goes to the root menu. Saves the current configuration to the access point system flash. Quits the CLI and exits the current session.
CLI Reference AP7131N>admin(system.power-setup)>show Description: Displays the access point’s current power configuration. Syntax: show Displays the access point’s current power configuration. Example: admin(system.power-setup)>show Power Mode : 3af Power Status : Mid Power 3af Power Option : option 3at Power Option : default Default Radio : Radio2 admin(system.power-setup)> For information on configuring power settings using the applet (GUI), see Configuring Power Settings on page 4-6.
8-166 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.power-setup)>set Description: Sets access point’s power consumption configuration. Syntax: set mode power-option def-radio Sets the power mode to either Auto or 3af. Changing the power mode restarts the AP, for the change to take effect. Defines the power option. Defines the radio receiving access port resource priority (1-Radio1, 2-Radio2). admin(system.power-setup)>set mode Auto admin(system.
CLI Reference 8.4.2 Adaptive AP Setup Commands AP7131N>admin(system)>aap-setup Description: Displays the Adaptive AP submenu. show set delete .. / save quit Displays Adaptive AP information. Defines the Adaptive AP configuration. Deletes static switch address assignments. Goes to the parent menu. Goes to the root menu. Saves the current configuration to the access point system flash. Quits the CLI and exits the current session.
8-168 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.aap-setup)>show Description: Displays the access point’s Adaptive AP configuration. Syntax: show Displays the access point’s Adaptive AP configuration. Example: admin(system.
CLI Reference AP7131N>admin(system.aap-setup)>set Description: Sets access point’s Adaptive AP configuration. Syntax: set auto-discovery ipadr name port passphrase tunnel-to-switch ac-keepalive load-balancing Sets the switch auto-discovery mode (enable/disable). Defines the switch IP address used. Defines the switch name for DNS lookups (up to 127 characters). Sets the port. Defines the pass phrase or key for switch connection. Enables/disables the tunnel between switch and access point.
8-170 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.aap-setup)>delete Description: Deletes static switch address assignments. Syntax: delete Deletes static switch address assignments by selected index. Deletes all assignments. Example: admin(system.aap-setup)>delete 1 admin(system.aap-setup)> For information on configuring Adaptive AP using the applet (GUI), see Adaptive AP Setup on page 4-11.
CLI Reference 8.4.3 System Access Commands AP7131N>admin(system)>access Description: Displays the access point access submenu. show set rmlock .. / save quit Displays access point system access capabilities. Goes to the access point system access submenu. Removes AP login locks Goes to the parent menu. Goes to the root menu. Saves the current configuration to the access point system flash. Quits the CLI and exits the current session.
8-172 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.access)>set Description: Defines the permissions to access the access point applet, CLI, SNMP as well as defining their timeout values. Syntax: set applet app-timeout ssh auth-timout slan swan inactive-timeout console-timeout rlogin snmp admin-auth server secret mode msg Enables/disables applet HTTPS access parameters from LAN.
CLI Reference AP7131N>admin(system.access)>show Description: Displays the current access point access permissions and timeout values. Syntax: show Shows all of the current system access settings for the access point.. Example: admin(system.
8-174 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.access)>rmlock Description: Removes AP login locks. The lock can be removed through console management interface (local RS-232 port) only. Syntax: rmlock Removes login locks of access point. Example: admin(system.access)>rmlock ssh admin(system.
CLI Reference 8.4.4 System Certificate Management Commands AP7131N>admin(system)>cmgr Description: Displays the Certificate Manager submenu. The items available under this command include: genreq delself loadself listself loadca delca listca showreq delprivkey listprivkey expcert impcert .. / save quit Generates a Certificate Request. Deletes a Self Certificate. Loads a Self Certificate signed by CA. Lists the self certificate loaded. Loads trusted certificate from CA. Deletes the trusted certificate.
8-176 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> genreq Description: Generates a certificate request. Syntax: genreq [-ou ] [-on ] [-cn ] ...
CLI Reference AP7131N>admin(system.cmgr)> delself Description: ) Deletes a self certificate. Syntax: delself Deletes the self certificate named . Example: admin(system.cmgr)>delself MyCert2 For information on configuring self certificate settings using the applet (GUI), see Creating Self Certificates on page 4-20.
8-178 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> loadself Description: Loads a self certificate signed by the Certificate Authority. Syntax: loadself Load the self certificate signed by the CA with name . Example: admin(system.cmgr)>loadself 1 Currently Only certificates in PEM format can be uploaded. Enter 'Ctrl C' to abort.
CLI Reference AP7131N>admin(system.cmgr)> listself Description: Lists the loaded self certificates. Syntax: listself Lists all self certificates that are loaded. Example: admin(system.cmgr)>listself Self Certificate List: admin(system.cmgr)> For information on configuring self certificate settings using the applet (GUI), see Creating Self Certificates on page 4-20.
8-180 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> loadca Description: Loads a trusted certificate from the Certificate Authority. Syntax: loadca Loads the trusted certificate (in PEM format only) that is pasted into the command line. Example: admin(system.cmgr)>loadca Currently Only certificates in PEM format can be uploaded. Enter 'Ctrl C' to abort.
CLI Reference AP7131N>admin(system.cmgr)> delca Description: Deletes a trusted certificate. Syntax: delca Deletes the trusted certificate. For information on configuring certificate settings using the applet (GUI), see Importing a CA Certificate on page 4-18.
8-182 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> listca Description: Lists the loaded trusted certificate. Syntax: listca Lists the loaded trusted certificates. For information on configuring certificate settings using the applet (GUI), see Importing a CA Certificate on page 4-18.
CLI Reference AP7131N>admin(system.cmgr)> showreq Description: Displays a certificate request in PEM format. Syntax: showreq Displays a certificate request named generated from the genreq command. For information on configuring certificate settings using the applet (GUI), see Importing a CA Certificate on page 4-18.
8-184 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> delprivkey Description: Deletes a private key. Syntax: delprivkey Deletes private key named . For information on configuring certificate settings using the applet (GUI), see Creating Self Certificates on page 4-20.
CLI Reference AP7131N>admin(system.cmgr)> listprivkey Description: Lists the names of private keys. Syntax: listprivkey Lists all private keys and displays their certificate associations. For information on configuring certificate settings using the applet (GUI), see Importing a CA Certificate on page 4-18.
8-186 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.cmgr)> expcert Description: Exports the certificate file to a user defined location. Syntax: expcert Exports the access point’s CA or Self certificate file. To export certificate information from an AP-7131N model access point: admin(system.
CLI Reference 8-187 AP7131N>admin(system.cmgr)> impcert Description: Imports the target certificate file. Syntax: impcert Imports the target certificate file. To import certificate information from an AP-7131N model access point: admin(system.cmgr)>impcert ? : : : : type: sftp file name: Certificate file name Server options for this file are the same as that for the configuration file admin(system.cmgr)>impcert sftp AP-7131Ncerts.
8-188 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.5 System SNMP Commands AP7131N>admin(system)> snmp Description: Displays the SNMP submenu. The items available under this command are shown below. access traps .. / save quit Goes to the SNMP access submenu. Goes to the SNMP traps submenu. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
CLI Reference 8.4.5.1 System SNMP Access Commands AP7131N>admin(system.snmp.access) Description: Displays the SNMP Access menu. The items available under this command are shown below. show add delete list .. / save quit Shows SNMP v3 engine ID. Adds SNMP access entries. Deletes SNMP access entries. Lists SNMP access entries. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash. Quits the CLI.
8-190 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.snmp.access)> show Description: Shows the SNMP v3 engine ID. Syntax: show eid Shows the SNMP v3 Engine ID. Example: admin(system.snmp.access)>show eid AP-7131N snmp v3 engine id : 000001846B8B4567F871AC68 admin(system.snmp.access)> For information on configuring SNMP access settings using the applet (GUI), see Configuring SNMP Access Control on page 4-33.
CLI Reference 8-191 AP7131N>admin(system.snmp.access)> add Description: Adds SNMP access entries for specific v1v2 and v3 user definitions. Syntax: add acl v3 Adds an entry to the SNMP access control list with as the starting IP address and and as the ending IP address. : user - username 1 to 31 characters : access - read/write access - (ro,rw) : oid - string 1 to 127 chars - E.g. 1.3.6.
8-192 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.snmp.access)> delete Description: Deletes SNMP access entries for v3 user definitions. Syntax: delete acl v3 all all Deletes entry (1-10) from the access control list. Deletes all entries from the access control list. Deletes entry (1-10) from the v3 user definition list. Deletes all entries from the v3 user definition list. Example: admin(system.snmp.
CLI Reference AP7131N>admin(system.snmp.access)> list Description: Lists SNMP access entries. Syntax: list acl v3 all Lists SNMP access control list entries. Lists SNMP v3 user definition by index (1-10). Lists all SNMP v3 user definitions. Example: admin(system.snmp.access)>list acl ---------------------------------------------------------------index start ip end ip ---------------------------------------------------------------1 209.236.24.1 209.236.24.46 admin(system.snmp.
8-194 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.5.2 System SNMP Traps Commands AP7131N>admin(system.snmp.traps) Description: Displays the SNMP traps submenu. The items available under this command are shown below. show set add delete list .. / save quit Shows SNMP trap parameters. Sets SNMP trap parameters. Adds SNMP trap entries. Deletes SNMP trap entries. Lists SNMP trap entries. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash.
CLI Reference AP7131N>admin(system.snmp.traps)> show Description: Shows SNMP trap parameters. Syntax: show trap rate-trap Shows SNMP trap parameter settings. Shows SNMP rate-trap parameter settings. Example: admin(system.snmp.
8-196 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.snmp.traps)> set Description: Sets SNMP trap parameters. Syntax: set mu-assoc mu-unassoc mu-deny-assoc mu-deny-auth snmp-auth snmp-acl dos-attack interval cold cfg rogue-ap ap-radar enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable enable/disable Enables/disables the MU associated trap.
CLI Reference 8-197 AP7131N>admin(system.snmp.traps)> add Description: Adds SNMP trap entries. Syntax: add v3 Adds an entry to the SNMP v3 access list with the destination IP address set to , the destination UDP port is set to , the username set to (1 to 31 characters), and the authentication type set to one of auth, or auth/priv.
8-198 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.snmp.traps)> delete Description: Deletes SNMP trap entries. Syntax: delete v3 all Deletes entry from the v3 access control list. Deletes all entries from the v3 access control list. Example: admin(system.snmp.traps)>delete v3 all For information on configuring SNMP traps using the applet (GUI), see Configuring SNMP Settings on page 4-27.
CLI Reference AP7131N>admin(system.snmp.traps)> list Description: Lists SNMP trap entries. Syntax: ist v3 all Lists SNMP v3 access entry . Lists all SNMP v3 access entries. Example: admin(system.snmp.traps)>add v3 201.232.24.33 555 BigBoss nonesha1 admin(system.snmp.traps)>list v3 all index : 1 destination ip : 201.232.24.
8-200 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.6 System User Database Commands AP7131N>admin(system)> userdb Description: Goes to the user database submenu. Syntax: user group save .. / Goes to the user submenu. Goes to the group submenu. Saves the configuration to system flash. Goes to the parent menu. Goes to the root menu. For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
CLI Reference 8-201 8.4.5.1 Adding and Removing Users from the User Database AP7131N>admin(system.userdb)> user Description: Adds and remvoves users from the user database and defines user passwords. Syntax: Wireless Users add delete clearall set show .. / save Adds a new user. Deletes a new user. Removes all existing user IDs from the system. Sets a password for a user. Displays the current user database configuration. Goes to the parent menu. Goes to the root menu.
8-202 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.user)> add Description: Adds a new user to the user database. Syntax: add Adds a new user ID and password string (8-19 characters) to the user database. Example: admin(system.userdb.user>add george password admin(system.userdb.user> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
CLI Reference 8-203 AP7131N>admin(system.userdb.user)> delete Description: Removes a new user to the user database. Syntax: delete Removes a user ID and password string from the user database. Example: admin(system.userdb.user>delete george admin(system.userdb.user> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
8-204 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.user)>clearall Description: Removes all existing user IDs from the system. Syntax: clearall Removes all existing user IDs from the system. Example: admin(system.userdb.user>clearall admin(system.userdb.user> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
CLI Reference 8-205 AP7131N>admin(system.userdb.user)>set Description: Sets a password for a user. Syntax: set Sets user and password string (8-19 characters) for a specific user. Example: admin(system.userdb.user>set george password admin(system.userdb.user> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
8-206 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.user)>mgmt-add Description: Adds a new management user. Syntax: mgmt-add Creates a user and password string (8-19 characters) for a new management user. Example: admin(system.userdb.user>mgmt-add John Motorola123 admin(system.userdb.
CLI Reference AP7131N>admin(system.userdb.user)>mgmt-delete Description: Deletes a management user identity. Syntax: mgmt-delete Deletes a management user. Example: admin(system.userdb.user>mgmt-delete george admin(system.userdb.
8-208 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.user)>mgmt-clearall Description: Removes all the management user accounts except admin account. Syntax: mgmt-clearall Removes all the management user accounts except admin account Example: admin(system.userdb.user>mgmt-clearall admin(system.userdb.
CLI Reference 8-209 AP7131N>admin(system.userdb.user)>mgmt-set Description: Sets the password for management user. Syntax: mgmt-set Sets a user and password string (8-19 characters) for a specific management user. Example: admin(system.userdb.user>mgmt-set john motorola123 admin(system.userdb.
8-210 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.user)>show Description: Displays existing user details. Syntax: show mgmt-users users groups Displays existing management users. Displays configured user IDs for a group. Displays configured groups. Example: admin(system.userdb.user>show mgmt-users Warning: This will display secure information. Do you want to continue [n/y]?y List of User Ids : John admin(system.userdb.
CLI Reference 8-211 8.4.5.2 Adding and Removing Groups from the User Database AP7131N>admin(system.userdb)> group Description: Adds and remvoves groups from the user database. Syntax: create delete clearall add remove show save .. / Creates a group name. Deletes a group name. Removes all existing group names from the system. Adds a user to an existing group. Removes a user from an existing group. Displays existing groups. Saves the configuration to system flash. Goes to the parent menu.
8-212 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.group> create Description: Creates a group name. Once defined, users can be added to the group. Syntax: create Creates a group name string. Once defined, users can be added to the group. Example: admin(system.userdb.group>create 2 admin(system.userdb.group> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
CLI Reference 8-213 AP7131N>admin(system.userdb.group> delete Description: Deletes an existing group. Syntax: delete Deletes an existing group name string. Example: admin(system.userdb.group>delete 2 admin(system.userdb.group> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
8-214 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.group> clearall Description: Removes all existing group names from the system. Syntax: clearall Removes all existing group names from the system. Example: admin(system.userdb.group>clearall admin(system.userdb.group> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
CLI Reference 8-215 AP7131N>admin(system.userdb.group> add Description: Adds a user to an existing group. Syntax: add Adds a user to an existing group . Example: admin(system.userdb.group>add lucy group x admin(system.userdb.group> For information on configuring User Database permissions using the applet (GUI), see Defining User Access Permissions by Group on page 6-67.
8-216 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.userdb.group> remove Description: Removes a user from an existing group. Syntax: remove Removes a user from an existing group . Example: admin(system.userdb.group>remove lucy group x admin(system.userdb.
CLI Reference 8-217 AP7131N>admin(system.userdb.group> show Description: Displays existing groups. Syntax: show users groups Displays existing groups and users, Displays configured user IDs for a group. Displays configured groups. Example: admin(system.userdb.group>show groups Warning: This will display secure information, Do you want to continue? (n/y?)y List of Group Names : engineering : marketing : demo room admin(system.userdb.
8-218 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.7 System Radius Commands AP7131N>admin(system)> radius Description: Goes to the Radius system submenu. Syntax: eap policy ldap proxy client set show save quit .. / Goes to the EAP submenu. Goes to the access policy submenu. Goes to the LDAP submenu. Goes to the proxy submenu. Goes to the client submenu. Sets Radius parameters. Displays Radius parameters. Saves the configuration to system flash. Quits the CLI.
CLI Reference AP7131N>admin(system.radius)> set/show Description: Sets or displays the Radius user database. Syntax: set show all Sets the Radius user database. Displays the Radius user database. Example: admin(system.radius)>set database local admin(system.radius)>show all Database : local admin(system.radius)> For information on configuring Radius using the applet (GUI), see Configuring User Authentication on page 6-52.
8-220 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.6.1 AP7131N>admin(system.radius)> eap Description: Goes to the EAP submenu. Syntax: peap ttls import set show save quit .. / Goes to the Peap submenu. Goes to the TTLS submenu. Imports the requested EAP certificates. Defines EAP parameters. Displays the EAP configuration. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu.
CLI Reference AP7131N>admin(system.radius.eap)> peap Description: Goes to the Peap submenu. Syntax: set show save quit .. / Defines Peap parameters. Displays the Peap configuration. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu. For information on configuring PEAP Radius using the applet (GUI), see Configuring User Authentication on page 6-52.
8-222 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.eap.peap> set/show Description: Defines and displays Peap parameters Syntax: set show Sets the Peap authentication . Displays the Peap authentication type. Example: admin(system.radius.eap.peap)>set auth gtc admin(system.radius.eap.peap)>show PEAP Auth Type : gtc For information on configuring EAP PEAP Radius values using the applet (GUI), see Configuring User Authentication on page 6-52.
CLI Reference AP7131N>admin(system.radius.eap)> ttls Description: Goes to the TTLS submenu. Syntax: set show save quit .. / Defines TTLS parameters. Displays the TTLS configuration. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu. For information on configuring EAP TTLS Radius values using the applet (GUI), see Configuring User Authentication on page 6-52.
8-224 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.eap.ttls> set/show Description: Defines and displays TTLS parameters Syntax: set show Sets the default TTLS authentication . Displays the TTLS authentication . Example: admin(system.radius.eap.ttls)>set auth pap admin(system.radius.eap.
CLI Reference 8.4.6.2 AP7131N>admin(system.radius)> policy Description: Goes to the access policy submenu. Syntax: set access-time show save quit .. / Sets a group’s WLAN access policy. Goes to the time based login submenu. Displays the group’s access policy. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu. For information on configuring Radius access policies using the applet (GUI), see Configuring User Authentication on page 6-52.
8-226 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.policy> set Description: Defines the group’s WLAN access policy. Syntax: set Defines the group’s WLAN access policy (defined as a string) delimited by a space. Example: admin(system.radius.policy)>set engineering 16 admin(system.radius.
CLI Reference 8-227 AP7131N>admin(system.radius.policy> access-time Description: set Goes to the time-based login submenu. Syntax: set show save quit .. / Defines a target group’s access time permissions. Access time is in Day DDDD-DDDD format. Displays the group’s access time rule. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu. Example: admin(system.radius.policy.
8-228 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.policy> show Description: Displays a group’s access policy. Syntax: show Displays a group’s access policy. Example: admin(system.radius.policy)>show Warning: This will display secure information, Do you want to continue? (n/y?)y List of Access Policies engineering marketing demo room test demo : : : : 16 10 3 No Wlans admin(system.radius.
CLI Reference 8.4.6.3 AP7131N>admin(system.radius)> ldap Description: Goes to the LDAP submenu. Syntax: set show all save quit .. / Defines the LDAP parameters. Displays existing LDAP parameters. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu. For information on configuring a Radius LDAP server using the applet (GUI), see Configuring LDAP Authentication on page 6-57.
8-230 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.ldap)> set Description: Defines the LDAP parameters. Syntax: set ipadr binddn basedn passwd login pass_attr groupname filter membership Defines the LDAP parameters. Sets LDAP IP address. Sets LDAP bind distinguished name. Sets LDAP base distinguished name. Sets LDAP server password. The password length must be 8-16 characters. Sets LDAP login attribute. Sets LDAP password attribute.
CLI Reference 8-231 AP7131N>admin(system.radius.ldap)> show all Description: Displays existing LDAP parameters. Syntax: show all Displays existing LDAP parameters. Example: admin(system.radius.ldap)>show all Warning: This will display secure information, Do you want to continue? (n/y?)y LDAP Server IP : 0.0.0.
8-232 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.6.4 AP7131N>admin(system.radius)> proxy Description: Goes to the Radius proxy server submenu. Syntax: add delete clearall set show save quit .. / Adds a proxy realm. Deletes a proxy realm. Removes all proxy server records. Sets proxy server parameters. Displays current Radius proxy server parameters. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu.
CLI Reference 8-233 AP7131N>admin(system.radius.proxy)> add Description: Adds a proxy. Syntax: add name ip1 sec Adds a proxy realm. Realm name. Authentication server IP address. The default port is set to 1812. Shared secret password. Example: admin(system.radius.proxy)>add lancelot 157.235.241.22 1812 muddy admin(system.radius.proxy)> For information on configuring Radius proxy server values using the applet (GUI), see Configuring a Proxy Radius Server on page 6-59.
8-234 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.proxy)> delete Description: Adds a proxy. Syntax: delete Deletes a realm name. Example: admin(system.radius.proxy)>delete lancelot admin(system.radius.proxy)> For information on configuring Radius proxy server values using the applet (GUI), see Configuring a Proxy Radius Server on page 6-59.
CLI Reference 8-235 AP7131N>admin(system.radius.proxy)> clearall Description: Removes all proxy server records from the system. Syntax: clearall Removes all proxy server records from the system. Example: admin(system.radius.proxy)>clearall admin(system.radius.proxy)> For information on configuring Radius proxy server values using the applet (GUI), see Configuring a Proxy Radius Server on page 6-59.
8-236 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.proxy)> set Description: Sets Radius proxy server parameters. Syntax: set delay count Sets Radius proxy server parameters. Defines retry delay time (in seconds) for the proxy server. The minimum value is 5 and maximum value is 10. Defines retry count value for the proxy server. The minimum value is 3 and maximum value is 6. Example: admin(system.radius.proxy)>set delay 10 admin(system.radius.
CLI Reference 8.4.6.5 AP7131N>admin(system.radius)> client Description: Goes to the Radius client submenu. Syntax: add delete show save quit .. / Adds a Radius client to list of available clients. Deletes a Radius client from list of available clients. Displays a list of configured clients. Saves the configuration to system flash. Quits the CLI. Goes to the parent menu. Goes to the root menu.
8-238 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.client> add Description: Adds a Radius client to those available to the Radius server. Syntax: add ip mask secret Adds a proxy. Client’s IP address. Network mask address of the client. Shared secret password. The password length must be 8-16 characters. Example: admin(system.radius.client)>add 157.235.132.11 255.255.255.225 muddy admin(system.radius.
CLI Reference AP7131N>admin(system.radius.client> delete Description: Removes a specified Radius client from those available to the Radius server. Syntax: delete ipadr Removes a specified Radius client from those available to the Radius server Example: admin(system.radius.client)>delete 157.235.132.11 admin(system.radius.client)> For information on configuring Radius client values using the applet (GUI), see Configuring the Radius Server on page 6-52.
8-240 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.radius.client> show Description: Displays a list of configured Radius clients. Syntax: show Removes a specified Radius client from those available to the Radius server. Example: admin(system.radius.
CLI Reference 8-241 8.4.8 System Network Time Protocol (NTP) Commands AP7131N>admin(system)> ntp Description: Displays the NTP menu. The correct network time is required for numerous functions to be configured accurately on the access point. Syntax: show date-zone zone-list set .. / save quit Shows NTP parameters settings. Show date, time and time zone. Displays list of time zones. Sets NTP parameters. Goes to the parent menu. Goes to the root menu. Saves the configuration to system flash.
8-242 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.ntp)> show Description: Displays the NTP server configuration. Syntax: show Shows all NTP server settings. Example: admin(system.ntp)>show current time : Tue 2011-Dec-13 16:58:59 +0530 IST time zone : Asia/Calcutta ntp mode : disable admin(system.ntp)> For information on configuring NTP using the applet (GUI), see Configuring Network Time Protocol (NTP) on page 4-41.
CLI Reference AP7131N>admin(system.ntp)> date-zone Description: Show date, time and time zone. Syntax: date-zone Show date, time and time zone. Example: admin(system.ntp)>date-zone Date/Time : Tue 2011-Jan-02 18:35:37 +0000 UTC Time Zone : UTC CliAuditLog - User:'admin' Command:'date-zone ' Status:'success' From:'Ssh172.16.10.10' MU_Mac:'NULL' admin(system.ntp)> For information on configuring NTP using the applet (GUI), see Configuring Network Time Protocol (NTP) on page 4-41.
8-244 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.ntp)> zone-list Description: Displays an extensive list of time zones for countries around the world. Syntax: zone-list Displays list of time zone indexes for every known zone. Example: admin(system.
CLI Reference AP7131N>admin(system.ntp)> set Description: Sets NTP parameters for access point clock synchronization. Syntax: set mode server intrvl time
8-246 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.9 System Log Commands AP7131N>admin(system)> logs Description: Displays the access point log submenu. Logging options include: Syntax: show filter-show set unset-filter view delete .. / save quit Shows logging options. Shows all filters. Sets log options and parameters. Unsets filters. Views system log. Deletes the system log. Goes to the parent menu. Goes to the root menu. Saves configuration to system flash. Quits the CLI.
CLI Reference AP7131N>admin(system.logs)> show Description: Displays the current access point logging settings. Syntax: show Displays the current access point logging configuration. Example: admin(system.logs)>show log level : L6 Info syslog server logging : enable syslog server ip address : 192.168.0.102 For information on configuring logging settings using the applet (GUI), see Logging Configuration on page 4-45.
8-248 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.logs)>filter-show Description: Displays filters.based on the specified rule Syntax: filter-show idx all Displays the filters based on the specified rule Displays all filters Example admin(system.
CLI Reference AP7131N>admin(system.logs)>unset-filter Description: Unsets filters.based on the specified rule Syntax: unset-filter idx all Unsets filters based on the specified rule precedence number Unsets all filters Example admin(system.
8-250 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.logs)> set Description: Sets log options and parameters. Syntax: set level mode ipadr auditfilter Sets the level of the events that will be logged. All events with a level at or above (L0-L7) will be saved to the system log. L0:Emergency L1:Alert L2:Critical L3:Errors L4:Warning L5:Notice L6:Info (default setting) L7:Debug Enables or disables syslog server logging.
CLI Reference 8-251 AP7131N>admin(system.logs)> view Description: Displays the access point system log file. Syntax: view Displays the entire access point system log file. Example: admin(system.logs)>view Warning: This will display secure information, Do you want to continue? (n/y?)y Jan 7 16:14:00 (none) syslogd 1.4.1: restart (remote reception).
8-252 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.logs)> delete Description: Deletes the log files. Syntax: delete Deletes the access point system log file. Example: admin(system.logs)>delete For information on configuring logging settings using the applet (GUI), see Logging Configuration on page 4-45.
CLI Reference 8.4.10 System Configuration-Update Commands AP7131N>admin(system.config)> Description: Displays the access point configuration update submenu. Syntax: default partial show set export import transfer_keys_cfg .. / save quit Restores the default access point configuration. Restores a partial default access point configuration. Shows import/export parameters. Sets import/export access point configuration parameters. Exports access point configuration to a designated system.
8-254 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.config)> default Description: Restores the full access point factory default configuration. Syntax: default Restores the access point to the original (factory) configuration. Example: admin(system.
CLI Reference 8-255 AP7131N>admin(system.config)> partial Description: Restores a partial factory default configuration. The access point’s LAN, WAN and SNMP settings are uneffected by the partial restore. Syntax: default Restores a partial access point configuration. Example: admin(system.
8-256 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.config)> show Description: Displays import/export parameters for the access point configuration file. Syntax: show Shows all import/export parameters. Example: admin(system.config)>show Warning: This will display secure information, Do you want to continue? (n/y?)y cfg filename : cfg.txt cfg filepath : sftp server ip address : 192.268.0.
CLI Reference 8-257 AP7131N>admin(system.config)> set Description: Sets the import/export parameters. Syntax: set file path server user Sets the configuration file name (1 to 39 characters in length). Defines the path used for the configuration file upload. Sets the SFTP server IP address. Sets the SFTP user name (1 to 39 characters in length). Example: admin(system.config)>set server 192.168.22.12 admin(system.config)>set user myadmin admin(system.
8-258 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.config)> export Description: Exports the configuration from the system. Syntax: export sftp Exports the access point configuration to the SFTP server. Use the set command to set the server, user, password, and file name before using this command. Example: admin(system.config)>set server 192.168.22.12 admin(system.config)>set user myadmin admin(system.config)>set file config.txt admin(system.
CLI Reference 8-259 AP7131N>admin(system.config)> import Description: Imports the access point configuration to the access point. Errors could display as a result of invaid configuration parameters. Correct the sepcified lines and import the file again until the import operation is error free. Syntax: import sftp Imports the access point configuration file from the SFTP server. Use the set command to set the server, user, password, and file. Example: admin(system.config>set server 192.168.22.
8-260 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.config)>transfer_keys_cfg Description: Exports SSH keys in order to turn off interactive mode. Syntax: transfer_keys Exports SSH keys in order to turn off interactive mode.xx Example: admin(system.config>transfer_keys_cfg Transfer of ssh public key in progress Done. admin(system.
CLI Reference 8.4.11 Firmware Update Commands AP7131N>admin(system)>fw-update Description: Displays the firmware update submenu. The items available under this command are shown below. NOTE The access point must complete the reboot process to successfully update the device firmware, regardless of whether the reboot is conducted uing the GUI or CLI interfaces. show set transfer_keys_fw update .. / save quit Displays the current access point firmware update settings.
8-262 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.fw-update)>show Description: Displays the current access point firmware update settings. Syntax: show Shows the current system firmware update settings for the access point. Example: admin(system.fw-update)>show Warning: This will display secure information, Do you want to continue? (n/y?)y firmware filename firmware path sftp server ip address sftp user name : : : : apn.bin /sftpboot/ 168.197.2.
CLI Reference AP7131N>admin(system.fw-update)>set Description: Defines access point firmware update settings and user permissions. Syntax: set file path server user Defines the firmware file name (1 to 39 characters). Specifies a path for the file (1 to 39 characters).. The IP address for the SFTP server used for the firmware and/or config file update. Specifies a username for SFTP server login (1 to 39 characters). admin(system.fw-update)>set file 3.0.0.0-29D admin(system.
8-264 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.fw-update)>transfer_keys_fw Description: Execute this command to export ssh keys to turn off interactive mode on firmware Syntax transfer_keys_fw Exports ssh keys to turn off interactive mode on firmware Example: admin(system.
CLI Reference AP7131N>admin(system.fw-update)>update Description: Executes the access point firmware update over the WAN or LAN port using SFTP. Syntax: update Defines the sftp mode used to conduct the firmware update. Specifies whether the update is executed over the access point’s WAN, LAN1 or LAN2 interface . NOTE The access point must complete the reboot process to successfully update the device firmware, regardless of whether the reboot is conducted uing the GUI or CLI interfaces.
8-266 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 8.4.12 FIPS Test Commands AP7131N>admin(system)>fips-test Description: Displays the fips-test submenu. The items available under this command are shown below. run-self-test zeroisekeys showlog .. / save quit Performs self test. Zeroization of critical security parameters. Displays the PoST Log File success or error status. Goes to the parent menu. Goes to the root menu.
CLI Reference 8-267 AP7131N>admin(system.fips-test)>run-self-test Description: Execute this command to perform a self test. Syntax: run-self-test Conducts a self test. Example: admin(system.
8-268 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Fri Aug 31 18:47:52 2012 1. RNG Test...Successful Fri Aug 31 18:47:52 2012 2. AES encryption/decryption...Successful Fri Aug 31 18:47:52 2012 3. 3DES-ECB encryption/decryption...Successful Fri Aug 31 18:47:52 2012 4. SHA-1 hash...Successful Fri Aug 31 18:47:52 2012 5. HMAC-SHA-1 hash...
CLI Reference 8-269 AP7131N>admin(system.fips-test)>zeroisekeys Description: Conducts a zeroization of critical security parameters by restrating the access point and restoring its default configuration. A new, more secure, password will then be required. Syntax: zeroisekeys Conducts a zeroization of critical security parameters. The country code must be supplied to continue with the CLI session. admin(system.fips-test)>zeroisekeys WARNING: Zeroizing.....
8-270 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(system.fips-test)>showlog Description: Displays the PoST Logs File success or error state. Syntax: showlog Displays the PoST Logs File success or error state. admin(system.fips-test)>showlog admin(system.
CLI Reference 8.5 Statistics Commands AP7131N>admin(stats) Description: Displays the access point statistics submenu. The items available under this command are: show clear flash-all-leds echo ping .. / save quit Displays access point WLAN, MU, LAN and WAN statistics. Clears all statistic counters to zero. Starts and stops the flashing of all access point LEDs. Defines the parameters for pinging a designated station. Iniates a ping test. Moves to the parent menu. Goes to the root menu.
8-272 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(stats)> show Description: Displays access point system information. Syntax: show wan lan stp wlan s-wlan radio s-radio retry-hgram mu s-mu auth-mu mesh s-mesh known-ap Displays stats for the access point WAN port. Displays stats for the access point LAN port Displays LAN Spanning Tree Status Displays WLAN status and statistics summary.
CLI Reference AP7131N>admin(stats)> clear Description: Clears the specified statistics counters to zero to begin new data calculations. Syntax: clear wan lan all-rf all-wlan wlan all-radio radio1 radio2 all-mu mu known-ap Clears WAN statistics counters. Clears LAN statistics counters for specified LAN index (either clear lan 1 or clear lan 2). Clears all RF data. Clears all WLAN summary information. Clears individual WLAN statistic counters. Clears access point radio summary information.
8-274 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(stats)> flash-all-leds Description: Starts and stops the illumination of a specified access point’s LEDs. Syntax: flash-all-leds Defines the Known AP index number of the target AP to flash. Begins or terminates the flash activity.
CLI Reference AP7131N>admin(stats)> echo Description: Defines the echo test values used to conduct a ping test to an associated MU. Syntax: show list set start .. / quit Shows the Mobile Unit Statistics Summary. Defines echo test parameters and result. Determines echo test packet data. Begins echoing the defined station. Goes to parent menu. Goes to root menu. Quits CLI session. For information on MU Echo and Ping tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
8-276 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin.stats.echo)> show Description: Shows Mobile Unit Statistics Summary. Syntax: show Shows Mobile Unit Statistics Summary. Example: admin(stats.echo)>show ---------------------------------------------------------------------------Idx IP Address MAC Address WLAN Radio T-put ABS Retries ---------------------------------------------------------------------------1 192.168.2.
CLI Reference AP7131N>admin.stats.echo)> list Description: Lists echo test parameters and results. Syntax: list Lists echo test parameters and results. Example: admin(stats.echo)>list Station Address : 00A0F8213434 Number of Pings : 10 Packet Length : 10 Packet Data (in HEX) : 55 admin(stats.echo)> For information on MU Echo and Ping tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
8-278 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin.stats.echo)>set Description: Defines the parameters of the echo test. Syntax: set station request length data Defines MU target MAC address. Sets number of echo packets to transmit (1-539). Determines echo packet length in bytes (1-539). Defines the particular packet data. For information on MU Echo and Ping tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
CLI Reference AP7131N>admin.stats.echo)> start Description: Initiates the echo test. Syntax: start Initiates the echo test. Example: admin(stats.echo)>start admin(stats.echo)>list Station Address : 00A0F843AABB Number of Pings : 10 Packet Length : 100 Packet Data (in HEX) : 1 Number of MU Responses : 2 For information on MU Echo and Ping tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
8-280 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin(stats)> ping Description: Defines the ping test values used to conduct a ping test to an AP with the same ESSID. Syntax: ping show list set start .. / quit Shows Known AP Summary details. Defines ping test packet length. Determines ping test packet data. Begins pinging the defined station. Goes to parent menu. Goes to root menu. Quits CLI session.
CLI Reference AP7131N>admin.stats.ping)> show Description: Shows Known AP Summary Details. Syntax: show Shows Known AP Summary Details. Example: admin(stats.ping)>show ---------------------------------------------------------------------------Idx IP Address MAC Address MUs KBIOS Unit Name ---------------------------------------------------------------------------1 192.168.2.
8-282 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin.stats.ping)> list Description: Lists ping test parameters and results. Syntax: list Lists ping test parameters and results. Example: admin(stats.ping)>list Station Address : 00A0F8213434 Number of Pings : 10 Packet Length : 10 Packet Data (in HEX) : 55 admin(stats.ping)> For information on Known AP tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
CLI Reference AP7131N>admin.stats.ping)> set Description: Defines the parameters of the ping test. Syntax: set station request length data Defines the AP target MAC address. Sets number of ping packets to transmit (1-539). Determines ping packet length in bytes (1-539). Defines the particular packet data. Example: admin(stats.ping)>set station 00A0F843AABB admin(stats.ping)>set request 10 admin(stats.ping)>set length 100 admin(stats.ping)>set data 1 admin(stats.
8-284 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide AP7131N>admin.stats.echo)> start Description: Initiates the ping test. Syntax: start Initiates the ping test. Example: admin(stats.ping)>start admin(stats.ping)>list Station Address : 00A0F843AABB Number of Pings : 10 Packet Length : 100 Packet Data (in HEX) : 1 Number of AP Responses : 2 For information on Known AP tests using the applet (GUI), see Pinging Individual MUs on page 7-30.
Configuring Mesh Networking 9.1 Mesh Networking Overview The access point can be configured in two modes to support the new mesh networking functionality. The access point can be set to a client bridge mode and/or a base bridge mode (which accepts connections from client bridges). Base bridge and client bridge mode can be used at the same time by an individual access point to optimally bridge traffic to other members of the mesh network and service associated MUs.
9-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide access points configured as both a base and a client bridge function as repeaters to transmit data with associated MUs in their coverage area (client bridge mode) as well as forward traffic to other access points in the mesh network (base bridge mode). The number of access points and their intended function within the mesh network dictate whether they should be configured as base bridges, client bridges or both (repeaters).
Configuring Mesh Networking If an access point is configured as a base bridge (but not as a client bridge) it operates normally at boot time. The base bridge supports connections made by other client bridges. The dual-radio model access point affords users better optimization of the mesh networking feature by enabling the access point to transmit to other mesh network members using one independent radio and transmit with associated MUs using the second independent radio.
9-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The access point in client bridge mode attempts to establish up to 3 simultaneous wireless connections. The second and third connections are established in the background while the system is running. The first connection needs to be established before the system starts bridging traffic.
Configuring Mesh Networking NOTE Motorola recommends using the Mesh STP Configuration screen to define a base bridge as a root. Only advanced users should use the Advanced Client Bridge Settings screen’s Preferred List to define the mesh topology, as omitting a bridge from the preferred list could break connections within the mesh network. The access point can manipulate the path cost assigned to a bridge connection based on that connection’s RSSI.
9-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 9.1.6 Impact of Importing/Exporting Configurations to a Mesh Network When using the access point’s Configuration Import/Export screen to migrate an access point’s configuration to other access points, mesh network configuration parameters will get sent or saved to other access points. However, if using the Known AP Statistics screen’s Send Cfg to APs functionality, “auto-select” and preferred list” settings do not get imported.
Configuring Mesh Networking 9.2 Configuring Mesh Networking Support Configuring the access point for Mesh Bridging support entails: • Setting the LAN Configuration for Mesh Networking Support • Configuring a WLAN for Mesh Networking Support • Configuring the Access Point Radio for Mesh Support. 9.2.
9-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Priority Set the Priority as low as possible for a to force other devices within the mesh network to defer to this client bridge as the bridge defining the mesh configuration (commonly referred to as the root). Motorola recommends assigning a Base Bridge AP with the lowest bridge priority so it becomes the root in the STP.
Configuring Mesh Networking Forward Delay The Forward Delay is the time spent in the listening and learning state. This time is equal to 15 sec by default, but you can tune the time to be between 4 and 30 sec. The 802.1d specification recommends the Forward Delay be set to a value greater than half the Max Message age timeout value.
9-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Assign an ESSID and Name to the WLAN that each access point will share when using this WLAN within their mesh network. Motorola recommends assigning a unique name to a WLAN supporting a mesh network to differentiate it from WLANs defined for non mesh support. The name assigned to the WLAN is what is selected from the Radio Configuration screen for use within the mesh network.
Configuring Mesh Networking 4. Use the Available On checkboxes to specify the access point radio(s) used with the target WLAN within the mesh network. The Available On checkboxes are for making this WLAN available for base bridges or repeaters to connect to. The Available On checkbox should only be selected for a mesh WLAN if this target access point is to be configured as a base bridge or repeater on the radio.
9-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide on the client bridge and repeater (an access point defined as both a base and client bridge) association requirements within the mesh network. For information on defining an ACL for use with the WLAN assigned to the mesh network, see Configuring a WLAN Access Control List (ACL) on page 5-35. 9.
Configuring Mesh Networking 9.2.3 Configuring the Access Point Radio for Mesh Support An access point radio intended for use within a mesh network requires configuration attributes unique from a radio intended for non-mesh support.This section describes how to configure an access point radio for mesh network support.
9-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Refer to the Radio Function parameter to ensure the radio has been designated for WLAN Radio support. NOTE With this 4.0 release of the access point firmware, a new scheme for radio configuration and WIPS server management has been implemented within the Quick Setup GUI applet. Up to eight radio buttons are now available (depending on the number radios supported by the SKU).
Configuring Mesh Networking 3. Select the Base Bridge checkbox to allow the access point radio to accept client bridge connections from other access points in client bridge mode. The base bridge is the acceptor of mesh network data from those client bridges within the mesh network and never the initiator. CAUTION A problem could arise if a Base Bridge’s Indoor channel is not available on an Outdoor Client Bridge's list of available channels.
9-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide NOTE Ensure you have verified the radio configuration for both Radio 1 and Radio 2 before saving the existing settings and exiting the Radio Configuration screen. 6. Click the Advanced button to define a prioritized list of access points to define mesh connection links. 7. Select the Automatic Link Selection checkbox to allow the access point to select the links used by the client bridge to populate the mesh network.
Configuring Mesh Networking MAC Address The MAC Address field displays the factory set hard-coded MAC address that serves as a device identifier. RSSI The Relative Signal Strength Indicator (RSSI) displays the located device’s signal strength with the associated access point in client bridge mode. Use this information as criteria on whether to move a particular device from the available list to the preferred list.
9-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide list can be re-populated with more desirable device MAC addresses from the Available Base Bridge List. 14. Click Ok to return to the Radio Configuration screen. Within the Radio Configuration screen, click Apply to save any changes made within the Advanced Client Bridge Settings screen. 15. Click Cancel to undo any changes made within the Advanced Client Bridge Settings screen.
Configuring Mesh Networking 17. Click Apply to save any changes to the Radio Configuration screen. Navigating away from the screen without clicking Apply results in all changes to the screens being lost. CAUTION When defining a Mesh configuration and changes are saved, the mesh network temporarily goes down. The mesh network is unavailable because the access point radio goes down when applying the changes. This can be problematic for users making changes within a deployed mesh network.
9-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 9.3 Mesh Network Deployment - Quick Setup This section provides instructions on how to quickly setup and demonstrate mesh functionality using three access points. Two following two deployment scenarios will be addressed: • • Scenario 1 - Two base bridges (redundant) and one client bridge Scenario 2 - A two hop mesh network with a base bridge, repeater (combined base bridge and client bridge mode) and a client bridge. 9.3.
Configuring Mesh Networking 9.3.1.1 Configuring AP#1: 1. Provide a known IP address for the LAN1 interface. NOTE Enable the LAN1 Interface of AP#1 as a DHCP Server if you intend to associate MUs and require them to obtain an IP address via DHCP.
9-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Assign a Mesh STP Priority of 40000 to LAN1 Interface. 3. Define a mesh supported WLAN.
Configuring Mesh Networking 4. Enable base bridge functionality on the 802.11a/n radio (Radio 2).
9-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 5. Define a channel of operation for the 802.11a/n radio. 6. If needed, create another WLAN mapped to the 802.11b/g/n radio if 802.11b/g/n support is required for MUs on that 802.11 band. 9.3.1.2 Configuring AP#2 AP#2 can be configured the same as AP#1 with the following exceptions: • • Assign an IP Address to the LAN1 Interface different than that of AP#1 Assign a higher Mesh STP Priority 50000 to the AP#2 LAN1 Interface.
Configuring Mesh Networking NOTE Ensure AP#1 and AP#2 use the same channel for each 802.11a/n radio, or the APs will not be able to “hear” each other over different channels. 9.3.1.3 Configuring AP#3 To define the configuration for AP#3 (a client bridge connecting to both AP#1 and AP#2 simultaneously): 1. Provide a known IP address for the LAN1 interface.
9-26 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Assign the maximum value (65535) for the Mesh STP Priority. 3. Create a mesh supported WLAN with the Enable Client Bridge Backhaul option selected. NOTE This WLAN should not be mapped to any radio. Therefore, leave both of the “Available On” radio options unselected. 4. Select the Client Bridge checkbox to enable client bridge functionality on the 802.11a/n radio.
Configuring Mesh Networking 5. If needed, create another WLAN mapped to the 802.11b/g/n radio if 802.11b/g/n support is required for MUs on that 802.11 band. 9.3.1.4 Verifying Mesh Network Functionality for Scenario #1 You now have a three AP mesh network ready to demonstrate. Associate a single MU on each AP WLAN configured for 802.11b/g/n radio support. Once completed, pass traffic among the three APs comprising the mesh network. 9.3.
9-28 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • • • AP#1 is a base bridge AP#2 is a repeater (client bridge/base bridge combination) AP#3 is a client b ridge 9.3.2.1 Configuring AP#1 The setup of AP#1 within this usage scenario is exactly the same as the AP#1 configuration within Scenario 1 - Two Base Bridges and One Client Bridge for step by step instructions for configuring AP#1, see Configuring AP#1: on page 9-21.
Configuring Mesh Networking 9.3.2.2 Configuring AP#2 AP#2 requires the following modifications from AP#2 in the previous scenario to function in base bridge/client bridge repeater mode. 1. Enable client bridge backhaul on the mesh supported WLAN.
9-30 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Enable client and base bridge functionality on the 802.11a/n radio 9.3.2.3 Configuring AP#3 To define AP #3’s configuration: 1. The only change needed on AP#3 (with respect to the configuration used in scenario #1), is to disable the Auto Link Selection option. Click the Advanced button within the Mesh Client Bridge Settings field.
Configuring Mesh Networking 2. Add the 802.11a/n Radio MAC Address. In scenario #2, the mesh WLAN is mapped to BSS1 on the 802.11a/n radio if each AP. The Radio MAC Address (the BSSID#1 MAC Address) is used for the AP#2 Preferred Base Bridge List. Ensure both the AP#1 and AP#2 Radio MAC Addresses are in the Available Base Bridge List. Add the AP#2 MAC Address into the Preferred Base Bridge List. 3. Determine the Radio MAC Address and BSSID MAC Addresses.
9-32 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 9.3.2.4 Verifying Mesh Network Functionality for Scenario #2 You now have a three AP demo multi-hop mesh network ready to demonstrate. Associate an MU on the WLANs configured on the 802.11b/g/n radio for each AP and pass traffic among the members of the mesh network.
Configuring Mesh Networking 9.4 Mesh Networking Frequently Asked Questions The following scenarios represent issues that could be encountered and resolved when defining an access point supported mesh configuration: Mesh Deployment Issue 1 - Client Bridge can only connect to one of two Base Bridges You have two access points configured as base bridges (AP1, AP2) and one access point defined as a as a client bridge (AP3). However, the client bridge is able to connect to only one of the base bridges.
9-34 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Mesh Deployment Issue 4 - Do I need to map a WLAN to a radio when configuring mesh backhaul on a Client Bridge? When creating a mesh backhaul WLAN on a client bridge only AP, do you need to map the WLAN on a radio? Resolution No, a client bridge only AP behaves just like an MU! It scans for base bridges and forms connections to them. It doesn't need to beacon on that WLAN.
Configuring Mesh Networking Resolution Yes, the access points are fairly close from a software deployment standpoint. So it is a supported configuration for three models to exist in a single topology. Mesh Deployment Issue 9 - Can I mesh between and an access point and an AP300? Can I mesh between an AP-7131N-FGR and a AP300 model access port? Resolution No, an AP300 does not support mesh networking.
9-36 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Resolution That is expected behavior, when you make a configuration change on a mesh supported AP, it brings the radio driver down and then back up again. Consequently, the AP needs to re-establish its mesh connection after saving the configuration.
Adaptive AP 10.1 Adaptive AP Overview An adaptive AP (AAP) is an access point that can adopt like an AP300 (L3) access port. The management of an AAP is conducted by the switch, once the access point connects to a Motorola RFS7000 model switch and receives its AAP configuration. An AAP provides: • • • • local 802.
10-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide The benefits of an AAP deployment include: • • • • Centralized Configuration Management & Compliance - Wireless configurations across distributed sites can be centrally managed by the wireless switch or cluster. WAN Survivability - Local WLAN services at a remote sites are unaffected in the case of a WAN outage.
Adaptive AP 10.1.2 Adaptive AP Management An AAP can be adopted, configured and managed like a thin access port from the wireless switch. NOTE To support AAP functionality, a RFS7000 model switch must be running firmware version 4.0 or higher. The access point must running firmware version 4.0 or higher to be converted into an AAP. NOTE An AAP cannot support a firmware download from the wireless switch.
10-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • Static IP addresses - Up to 12 switch IP addresses can be manually specified in an ordered list the AP can choose from. When providing a list, the AAP tries to adopt based on the order in which they are listed (from 1-12). NOTE An AAP can use it's LAN or WAN Ethernet interface to adopt. The LAN is PoE and has a default static IP address of 192.168.0.1/24. The WAN has no PoE support and has a default static IP address of 10.1.1.
Adaptive AP 10.1.8 Securing Data Tunnels between the Switch and AAP If a secure link (site-to-site VPN) from a remote site to the central location already exists, the AAP does not require IPSec be configured for adoption. For sites with no secure link to the central location, an AAP can be configured to use an IPSec tunnel (with AES 256 encryption) for adoption. The tunnel configuration is automatic on the AAP side and requires no manual VPN policy be configured.
10-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 10.1.10 Remote Site Survivability (RSS) RSS can be used to turn off RF activity on an AAP if it loses adoption (connection) to the switch.
Adaptive AP 10.2 Supported Adaptive AP Topologies For this version of the access point firmware, the following AAP topologies are supported: • • • • Extended WLANs Only Independent WLANs Only Extended WLANs with Independent WLANs Extended WLAN with Mesh Networking 10.2.
10-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 10.2.2 Extended WLANs Only An extended WLAN configuration forces all MU traffic through the switch. No wireless traffic is locally bridged by the AAP. Each extended WLAN is mapped to the access point's virtual LAN2 subnet. By default, the access point's LAN2 is not enabled and the default configuration is set to static with IP addresses defined as all zeros.
Adaptive AP 10.2.5 Extended WLAN with Mesh Networking Mesh networking is an extension of the existing wired network. There is no special configuration required, with the exceptions of setting the mesh and using it within one of the two extended VLAN configurations and defining an access point radio as a preferred base bridge. NOTE The mesh backhaul WLAN must be an independent WLAN mapped to LAN1.
10-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • Configure the switch’s FQDN on the AAP. The AAP can use this to resolve the IP address of the switch. 2. Use the switch’s secret password on the AAP for the switch to authenticate it. For additional information on defining the connection medium used by the access point t to receive an AAP configuration, see Adaptive AP Setup on page 4-11.
Adaptive AP 10.4 Establishing Basic Adaptive AP Connectivity This section defines the activities required to configure basic AAP connectivity RFS7000 model switch. In establishing a basic AAP connection, both the access point and switch require modifications to their respective default configurations.
10-12 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 2. Select the Auto Discovery Enable checkbox. Enabling auto discovery will allow the AAP to be detected by a switch once its connectivity medium has been configured (by completing steps 3-6) 3. Enter up to 12 Switch IP Addresses constituting the target switches available for AAP connection. The AAP will begin establishing a connection with the first addresses in the list.
Adaptive AP 7. Click Apply to save the changes to the AAP setup. NOTE The manual AAP adoption described above can also be conducted using the access point’s CLI interface using the admin(system.aapsetup)> command. 10.4.1.2 Adopting an Adaptive AP Using a Configuration File To adopt an AAP using a configuration file: 1. Refer to Adopting an Adaptive AP Manually and define the AAP switch connection parameters. 2. Export the AAP’s configuration to a secure location.
10-14 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 3. Ensure the Adopt unconfigured radios automatically option is NOT selected. When disabled, there is no automatic adoption of non-configured radios on the network. Additionally, default radio settings will NOT be applied to access ports when automatically adopted.
Adaptive AP 10.4.3 Adaptive AP Deployment Considerations Before deploying your switch/AAP configuration, refer to the following usage caveats to optimize its effectiveness: • • • • • • • • Extended WLANs are mapped to the AP’s LAN2 interface and all independent WLANs are mapped to the AP’s LAN1 Interface.
10-16 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 10.4.4 Sample Switch Configuration File for IPSec and Independent WLAN The following constitutes a sample RFS7000 switch configuration file supporting an AAP IPSec with Independent WLAN configuration. The sample output is as follows: ### show running-config ! ! configuration of RFS7000 version 4.1.4.0-014GR ! version 1.
Adaptive AP ip access-list extended RADIUS-ACL permit ip host 192.168.0.4 host 192.168.0.10 log rule-precedence 10 ruledescription "Primary RADIUS ACL" permit ip host 192.168.0.4 host 172.20.0.1 log rule-precedence 20 ruledescription "Secondary RADIUS Server" ip access-list extended REMOTE-VPN ip access-list extended Cluster-ACL ip access-list extended Cluster-Mob-ACL permit ip host 192.168.5.61 host 192.168.5.
10-18 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide snmp-server user snmptrap v3 encrypted auth sha 0xa38c581812b8fb074602362f65299741547564d7 snmp-server user snmpmanager v3 encrypted auth sha 0xef925e804cf8f7eb49258c5ce6b262a942c9f6c6 snmp-server user snmpoperator v3 encrypted auth sha 0xa3d5669f507d3777488d19d8c29286f0b0f21aac snmp-server enable traps snmp-server enable traps wireless ap-detection unauthorizedAPDetected snmp-server enable traps wireless ap-detection unauthorizedA
Adaptive AP license AP 48a2c0e176f652c3b14fc96c0e6e57e6ac002f0092a4e06cd3822e53f1b9e4879a644cbd42b37512 ! wireless mobility local-address 192.168.5.61 mobility enable mobility peer 192.168.5.89 manual-wlan-mapping enable wlan 1 enable wlan 1 ssid @@P-Pr0x! wlan 1 vlan 222 wlan 1 encryption-type ccmp wlan 1 authentication-type eap wlan 1 radius server primary 192.168.0.
10-20 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide wlan 10 ssid CC wlan 10 vlan 222 wlan 10 encryption-type ccmp wlan 10 inactivity-timeout 300 wlan 10 dot11i key 2 qnwGA69t848iAzBUjSJdPjIeQb7WWlEWgsyzUH4zwS/ 4gvtZauQ2rvSAgeFucZbJVv+vMNBvlA/JbvEjrAqNQ8ON9d+4Ht6iFTgf2/SAQ/ 2sIXfUfD8xOlEBoZUMP/Ky aap fwupdate filename apn_040004000026GRN.bin aap fwupdate ipaddress 192.168.0.
Adaptive AP ap-detection add 3 authorized any Alpha-Net ap-detection add 4 authorized any Alpha-Voice wips detect-window 10 no wips event ap-default-configuration enable wips event suspicious-ap-high-rssi filter-ageout 60 wips event suspicious-ap-high-rssi signal-strength-threshold -100 wips event fake-ap-flood threshold 60 wips event unauthorized-ap-using-authorized-ssid filter-ageout 60 smart-rf radio 1 radio-mac 00-23-68-97-D4-10 radio 2 radio-mac 00-23-68-97-D2-60 radio 3 radio-mac 00-23-68-0F-46-10 ra
10-22 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide authentication pre-share group 14 lifetime 86400 crypto isakmp policy 10000 encryption 3des hash sha authentication pre-share group 14 lifetime 86400 ! crypto ipsec transform-set AAP-TFSET esp-aes-256 esp-sha-hmac mode tunnel crypto ipsec transform-set REMOTE-TFSET esp-3des esp-sha-hmac mode transport crypto ipsec transform-set RADIUS-TFS esp-3des esp-sha-hmac mode tunnel ! crypto map AAP-SYSLOG-MAP 13 ipsec-isakmp set peer 255.
Adaptive AP interface ge1 switchport access vlan 13 ip dhcp trust ! interface ge2 switchport access vlan 1 ip dhcp trust ! interface ge3 switchport access vlan 192 ip dhcp trust ! interface ge4 switchport access vlan 10 ip dhcp trust ! interface me1 ip address 10.1.1.100/24 ! interface vlan1 ip address dhcp crypto map CLUSTER-MOB-MAP ! interface vlan192 ip address dhcp crypto map AAP-SYSLOG-MAP ! interface vlan222 ip address 222.222.222.
10-24 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide default-router 222.222.222.222 network 222.222.222.0/24 address range 222.222.222.2 222.222.222.200 ! service dhcp ! rtls rfid espi sole ! ip route 172.20.0.0/16 192.168.0.
Technical Specifications This appendix provides technical specifications for the following: • • • • Physical Characteristics Electrical Characteristics Radio Characteristics Country Codes
A-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide A.1 Physical Characteristics An AP-7131N-FGR model access point has the following physical characteristics: Dimensions 5.50 in. Depth x 7.88 in. Width x 1.38 in. Height 14 cm Depth x 20.32 cm Width x 3.5 cm Height Housing Metal, plenum-rated housing (UL2043) Weight 2.7 lbs Operating Temperature -4°F to 122°F/-20°C to 50°C Storage Temperature -40°F to 158°F/-40°C to 70°C Altitude 8000 ft.
Technical Specifications A.3 Radio Characteristics An AP-7131N-FGR has the following radio characteristics: Operating Channels All channels from 4920 MHz to 5825 MHz except channel 52 -64 Channels 1-13 (EU), Channels 1-11 (US/Canada) Channel 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory Data Rates Supported 802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps 802.11a: 6,9,12,18,24,36,48, and 54Mbps 802.
A-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide A.
Technical Specifications Country Code Country Code Cypress CY Russia RU Czech Rep.
A-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide Country Code Italy IT Jamaica JM Japan JP Jordan JO Kazakhstan KZ Kuwait KW Latvia LV Lebanon LB Liechtenstein LI Lithuania LT Luxembourg LU Macedonia MK Malaysia MY Malta MT Martinique MQ Country Code
Usage Scenarios This appendix provides practical usage scenarios for many of the access point’s key features. This information should be referenced as a supplement to the information contained within this Product Reference Guide.
B-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide B.1 Configuring an IPSEC Tunnel and VPN FAQs The access point has the capability to create a tunnel between an access point and a VPN endpoint. The access point can also create a tunnel from one access point to another access point. The following instruction assumes the reader is familiar with basic IPSEC and VPN terminology and technology.
Usage Scenarios 5. Enter the WAN port IP address of AP #1 for the Local WAN IP. 6. Within the Remote Subnet and Remote Subnet Mask fields, enter the LAN IP subnet and mask of AP #2 /Device #2. 7. Enter the WAN port IP address of AP #2/ Device #2 for a Remote Gateway. 8. Click Apply to save the changes. NOTE For this example, Auto IKE Key Exchange is used. Any key exchange can be used, depending on the security needed, as long as both devices on each end of the tunnel are configured exactly the same. 9.
B-4 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide 11. For the ESP Type, select ESP with Authentication and use AES 128-bit as the ESP encryption algorithm and SHA1 as the ESP authentication algorithm. Click OK. 12. Select the IKE Settings button. 13. Select Pre Shared Key (PSK) from the IKE Authentication Mode drop-down menu. 14. Enter a Passphrase. Passphrases must match on both VPN devices.
Usage Scenarios B.1.2 Configuring a Cisco VPN Device This section includes general instructions for configuring a Cisco PIX Firewall 506 series device. For the usage scenario described in this section, you will require the following: • • 1 Cisco VPN device 1 PC connected to the LAN side of the access point and the Cisco PIX.
B-6 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide B.1.3 Frequently Asked VPN Questions The following are common questions that arise when configuring a VPN tunnel. • Question 1: Does the access point IPSec tunnel support multiple subnets on the other end of a VPN concentrator? Yes. The access point can access multiple subnets on the other end of the VPN Concentrator from the access point's Local LAN Subnet by: • Creating multiple VPN Tunnels.
Usage Scenarios • Question 6: Can an IPSec tunnel over a PPPoE connection be established - such as a PPPoE enabled DSL link? Yes. The access point supports tunneling when using a PPPoE username and password. • Question 7: Can I setup an access point so clients can access both the WAN normally and only use the VPN when talking to specific networks? Yes. Only packets that match the VPN Tunnel Settings will be sent through the VPN tunnel.
B-8 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide • An 'allow' inbound rule. Scr Dst Transport ANY Scr port 1:65535 Dst port 1:65535 Rev NAT None • An 'allow' outbound rule. Scr Dst Transport ANY Scr port 1:65535 Dst port 1:65535 NAT None • For IKE, an 'allow' inbound rule.
Usage Scenarios No. However, clients could need extra routing information. Clients on the local LAN side should either use the access point as their gateway or have a route entry tell them to use the access point as the gateway to reach the remote subnet.
B-10 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide
Customer Support Comprehensive on-line support is available at the Support Central site at https://portal.motorolasolutions.com/Support/US-EN Support Central provides our customers with a wealth of information and online assistance including developer tools, software downloads, product manuals and online repair requests. When contacting the Motorola Solutions Support Center, please provide the following information: • • • serial number of unit model number or product name software type and version number.
C-2 Motorola Solutions AP-7131N-FGR Access Point Product Reference Guide North American Contacts Support (for warranty and service information): telephone: 1-800-653-5350 fax: (631) 738-5410 Email: https://portal.motorolasolutions.com/Support/US-EN International Contacts Outside North America: Motorola Solutions, inc. Symbol Place Winnersh Triangle, Berkshire, RG41 5TP United Kingdom 0800-328-2424 (Inside UK) +44 118 945 7529 (Outside UK) Web Support Sites Product Downloads and Manuals https://portal.
Index Numerics 32735 Heading 2 1.1.11 Symbol NetVision Phone/Spectralink Voice Prioritization. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16 AP-5131 statistical displays. . . . . . . . . . . . . . . . . . . . . 1-17 association process beacon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17 RSSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27 available protocols. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17 A B access options . .
IN-2 AP-7131N-FGR Access Point Product Reference Guide CLI, firewall commands . . . . . . . . . . . . . . . . . . . . . . . 8-148 CLI, firmware update . . . . . . . . . . . . . . . . . . . . . . . . . 8-261 CLI, log commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-246 CLI, network commands . . . . . . . . . . . . . . . . . . . . . . . . 8-11 CLI, network LAN commands . . . . . . . . . . . . . . . . . . . . 8-12 CLI, network LAN, DHCP commands . . . . . . . . . . . . . .
IN-3 M MAC layer bridging . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 management options . . . . . . . . . . . . . . . . . . . . . .1-28, 1-29 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14 media types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 mesh networking dual-radio AP-5131 . . . . . . . . . . . . . . . . . . . . . . . . 9-3 STP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 topology . . . . . . . . .
IN-4 AP-7131N-FGR Access Point Product Reference Guide statistics, radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18 statistics, WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 statistics, WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 suspended T-Bar installations . . . . . . . . . . . . . . . . . . . 2-13 system information general . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 System Configuration . . . . . . . . . . . .
MOTOROLA Solutions INC. 1301 E. ALGONQUIN ROAD SCHAUMBURG, IL 60196-1078, U.S.A. http://www.motorolasolutions.
