DIAL-UP DATA User’s Guide Iridium Satellite LLC Rev.
DIAL-UP DATA SERVICE--------------------------------------------------------------------------------------- TABLE OF CONTENTS 1 Dial-Up Data Overview.............................................................................................................. 3 2 Hardware/Software Requirements............................................................................................ 5 3 Modem Driver Installation and Configuration........................................................................
DIAL-UP DATA SERVICE--------------------------------------------------------------------------------------------------------- OVERVIEW 1 Dial-Up Data Overview Dial-Up Data Service provides dial-up connectivity through your Iridium phone to another computer, a remote LAN (e.g., a corporate network), or an Internet Service Provider (ISP). This service offers a nominal data rate of 2.4 Kbps.
DIAL-UP DATA SERVICE--------------------------------------------------------------------------------------------------------- OVERVIEW ISP Internet PSTN Iridium Gateway Corporate Network Figure 2. Iridium Dial-Up Data Connectivity Iridium Satellite LLC 4 Rev.
DIAL-UP DATA SERVICE-------------------------------------------------------- HARDWARE/SOFTWARE REQUIREMENTS 2 Hardware/Software Requirements To use Iridium Dial-Up Data Service, you will need the following: A Windows-based PC, with: • • • Windows 95, 98, Me, NT4.0 (Service Pack 4 or later) or 2000 CD-ROM drive Serial port A SIM Card that is provisioned for data (note that this SIM can also be used for voice calls).
DIAL-UP DATA-----------------------------------------------------------------------------------------------SETUP & CONFIGURATION 3 Modem Driver Installation and Configuration Prior to using your Iridium phone as a modem for Dial-Up Data, you must do the following: • • Install the Motorola Satellite Series™ modem driver on your PC, and Set up and configure a dial-up networking connection.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 3.1 Windows 95/98/Me Setup In order to install the modem driver and configure dial-up networking, you will need the following: The Iridium World Data Services CD An available communications port on your computer (e.g., COM1) Note: 3.1.1 The following instructions are for Windows Me.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 5. If you are using a laptop, you may be presented with the following screen. Select the Other radio button and click Next >. 6. Choose the checkbox marked “Don’t detect my modem; I will select it from a list.” Then, click Next >. Iridium Satellite LLC 8 Rev.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 7. Click on Have Disk… 8. The default drive setting is A:\, which is the default floppy drive on most computers. Insert the Iridium World Data Services CD into your CD drive, and click Browse… 9. Browse to the Dial-Up Data directory on the CD, and then click OK. Iridium Satellite LLC 9 Rev.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 10. In the Install New Modem window, select the Motorola Satellite Series Data Modem and click Next >. 11. Select an available Communications Port (or COM Port) on which to install the modem (e.g., COM1), and click Next >. This is the port to which you will connect your Iridium phone. Iridium Satellite LLC 10 Rev.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 12. Click Finish. 13. Click either Close or OK to close the Modem Properties window. 14. You have now completed the installation of the Motorola Satellite Series Data Modem. Continue with section 3.1.2. Iridium Satellite LLC 11 Rev.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 3.1.2 Configure Dial-Up Networking – Windows 95/98/Me In order to use your Iridium handset for dial-up networking, you need to create a new dial-up networking connection.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 3. In the Make a New Connection window, you must do the following: • In the Telephone number box, enter the telephone number you wish to use for your connection. Enter the number in international dialing format: 00 + Country Code + Area Code/Phone Number.
DIAL-UP DATA-----------------------------------------------------------------------------------------------WINDOWS 95/98/Me SETUP 5. In the Dial-Up Networking window, right click on your new dial-up connection and select Properties. 6. Upon selecting Properties, you will see a window similar to the one shown below. Select the General tab, and then de-select the check box for “Use area code and Dialing Properties.” Also, verify that you have entered the correct phone number.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 3.2 Windows NT4.0 Setup In order to install the modem driver and configure dial-up networking, you will need the following: The Iridium World Data Services CD An available communications port on your computer (e.g., COM1) Administrator privileges for Windows NT4.0 3.2.1 Install the Modem Driver – Windows NT4.0 1. Close all applications. 2.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 5. Choose the checkbox marked “Don’t detect my modem; I will select it from a list.” Then, click Next > to open the Install New Modem window. 6. Click on Have Disk… to open the Install From Disk window. Iridium Satellite LLC 16 Rev.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 7. The default drive setting is A:\, which is the default floppy drive on most computers. Insert the Iridium World Data Services CD into your CD drive, and browse to the Dial-Up Data directory on the CD. Click OK. 8. In the Install New Modem window, select the Motorola Satellite Series Data Modem and click Next >. Iridium Satellite LLC 17 Rev.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 9. Click the “Selected ports” radio button, and select an available Communications Port (or COM Port) on which to install the modem (e.g., COM1) and click Next >. This is the port to which you will connect your Iridium phone. 10. Click Finish to close the Install New Modem window. Iridium Satellite LLC 18 Rev.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 11. Click Close to close the Modems Properties window. 12. The Modem Setup window appears and asks if you would like to configure Dial-Up Networking. Click Yes. Iridium Satellite LLC 19 Rev.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 13. The Remote Access Setup window appears. Click Add to continue. Note: If a modem is already installed on the COM port that you would like to use for the Motorola Satellite Series Data Modem, select the modem in the list and click Remove. 14. Select the Motorola Satellite Series Data Modem from the list of RAS capable devices.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 3.2.2 Configure Dial-Up Networking – Windows NT4.0 In order to use your Iridium handset for dial-up networking, you need to create a new dial-up networking connection. In the Dial-Up Networking window, you can modify an existing connection type or create a new connection type.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 3. The New Phonebook Entry window appears. You must do the following: • In the Entry name box, enter a connection name. For example, if you are creating a connection to your Internet Service Provider, and your ISP is called “Saturn Internet”, you might name your connection “Iridium Saturn.
DIAL-UP DATA-------------------------------------------------------------------------------------------------- WINDOWS NT 4.0 SETUP 4. Verify the proper settings according to the window below. Click OK to save any changes. Upon returning to the New Phonebook Entry window, click OK. 5. Close the Dial-Up Networking window. 6. You have now completed the configuration of Dial-Up Networking. To connect your hardware and initiate a dial-up data call, continue with section 4. Iridium Satellite LLC 23 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 3.3 Windows 2000 Setup In order to install the modem driver and configure dial-up networking, you will need the following: The Iridium World Data Services CD An available communications port on your computer (e.g., COM1) Administrator privileges for Windows 2000 3.3.1 Install the Modem Driver – Windows 2000 1. Close all applications 2.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 5. Choose the checkbox marked “Don’t detect my modem; I will select it from a list.” Then, click Next > to open the Install New Modem window of the Add/Remove Hardware Wizard. 6. Click on Have Disk… to open the Install From Disk window. Iridium Satellite LLC 25 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 7. The default drive setting is A:\, which is the default floppy drive on most computers. Insert the Iridium World Data Services CD into your CD drive, and click Browse… 8. Browse to the Dial-Up Data directory on the CD, and then click OK. Iridium Satellite LLC 26 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 9. In the Install New Modem window, select the Motorola Satellite Series Data Modem and click Next >. 10. Click the “Selected ports” radio button, and select an available Communications Port (or COM Port) on which to install the modem (e.g., COM1). This is the port to which you will connect your Iridium phone. Click Next >. Iridium Satellite LLC 27 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 11. The following window will appear. Click Yes. 12. Click Finish to close the Install New Modem window. Iridium Satellite LLC 28 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 13. Click OK to close the Phone and Modem Options window. 14. You have now completed the installation of the Motorola Satellite Series Data Modem. Continue with section 3.3.2. Iridium Satellite LLC 29 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 3.3.2 Configure Dial-Up Networking – Windows 2000 In order to use your Iridium handset for dial-up networking, you need to create a new dial-up networking connection. In the Network and Dial-Up Connections window, you can modify an existing connection type or create a new connection type.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 3. In the Network Connection Type window of the Network Connection Wizard, select the appropriate Dial-up connection type (either “Dial-up to private network” or “Dial-up to the Internet”). This example assumes you are creating a connection to your Internet Service Provider. Click Next >. 4.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 5. In the Internet Connection Wizard, select “I connect through a phone line and a modem.” Click Next >. 6. The following Internet Connection Wizard window appears only if you have more than one modem installed. If this window appears, choose the Motorola Satellite Series Data Modem from the drop down list. Then, click Next >. Iridium Satellite LLC 32 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 7. In the Internet Connection Wizard window, you must do the following: • In the Telephone number box, enter the telephone number you wish to use for your connection. Enter the number in international dialing format: 00 + Country Code + Area Code/Phone Number.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 8. In the Internet Connection Wizard, enter your user name and password to access your ISP. Click Next >. 9. In the Internet Connection Wizard, enter a connection name. For example, if you are creating a connection to your ISP and your ISP is called Saturn Internet, you might name your connection “Iridium Saturn.” Click Next >. Iridium Satellite LLC 34 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 10. In the Internet Connection Wizard, if you have already configured your email (or you are not using Microsoft Outlook), select “No.” Click Next >. 11. In the Internet Connection Wizard, de-select “To connect to the Internet immediately…”. Click Finish to save your new connection. Iridium Satellite LLC 35 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 12. In the Dial-Up Networking window, right click on your new dial-up connection and select Properties. 13. Upon selecting Properties, you will see the window below. Select the General tab, and verify the settings with the figure below. Also, verify that you have entered the correct telephone number.
DIAL-UP DATA----------------------------------------------------------------------------------------------------- WINDOWS 2000 SETUP 14. From the General menu, click Configure… to verify the proper settings. The settings should match the figure below. Click OK to return to the Properties window, and then click OK again to close the Properties window. 15. You have now completed the configuration of Dial-Up Networking. To connect your hardware and initiate a dial-up data call, continue with section 4.
DIAL-UP DATA------------------------------------------------------------------------------ 9500/9505 PORTABLE PHONE SETUP 4 Hardware Connections 4.1 Setting up the 9500 or 9505 Portable Phone 1. Insert your data-provisioned SIM card into the phone. See the user guide for your phone if you need further instructions on how to insert the SIM card. 2. Connect the Data Adapter to the bottom of the phone. 3. (Optionally) connect a charging device to the Data Adapter. 4.
DIAL-UP DATA------------------------------------------------------------------------------ 9500/9505 PORTABLE PHONE SETUP 5. Plug the Serial Cable into the serial port on your computer. 6. Rotate and extend the phone’s antenna. Place the phone into the stand, or otherwise position the phone so that the antenna is vertical and has a clear view of the sky. 7. Continue with section 5. Iridium Satellite LLC 39 Rev.
DIAL-UP DATA----------------------------------------------------------------------------------------- 9570 PORTABLE DOCK SETUP 4.2 Setting up the 9570 Portable Dock 1. Insert your data-provisioned SIM card into the phone or the dock. See the user guide for your Portable Phone or Portable Dock if you need further instructions on how to insert the SIM card. 2. Insert the 9500 Portable Phone into the Portable Dock (or insert a 9505 Portable Phone, with optional dock adapter). 3.
DIAL-UP DATA-------------------------------------------------------------------------------------------- 9520 MOBILE PHONE SETUP 4.3 Setting up the 9520 Mobile Phone 1. Insert your data-provisioned SIM card into the Mobile Phone. See the user guide for your phone if you need further instructions on how to insert the SIM card. 2. The wiring harness for the 9520 Mobile Phone contains a built-in Serial Cable. Plug the Serial Cable into the serial port on your computer. 3.
DIAL-UP DATA---------------------------------------------------------------------------------------------------------------- DIALING A CALL 5 Dialing a Call To place a Dial-Up Data call, you must open the Dial-Up Networking window and select the dialup connection you created for your Motorola phone. 1. Connect the computer and phone as described in Section 4. 2. Orient the phone’s antenna with a clear view of the sky. 3. If your computer is turned off, turn it on and wait for it to boot up. 4.
DIAL-UP DATA---------------------------------------------------------------------------------------------------------------- DIALING A CALL Windows 95/98/Me: In the Connect To window, enter the user name and password that you use to access your ISP or corporate network, and if desired, click the “Save password” checkbox so that you do not have to re-enter the password every time a connection is made. Click Connect and your Iridium handset will begin to dial. Go to Step 8.
DIAL-UP DATA---------------------------------------------------------------------------------------------------------------- DIALING A CALL A window similar to the following will appear. Enter the user name and password that you use to access your ISP or corporate network. If desired, click the “Save password” checkbox so that you do not have to re-enter the password every time a connection is made. Press OK and your Iridium handset will begin to dial. Go to Step 8.
DIAL-UP DATA---------------------------------------------------------------------------------------------------------------- DIALING A CALL 8. As the Iridium phone is dialing, it will blink “Data Call In Progress” and a Dial-Up Networking window will appear on your computer showing the current status of the connection (just as it does when connecting through the landline network to your ISP or corporate network). 9.
DIALUP DATA--------------------------------------------------------------------------------------------------------- TRADEMARK NOTICE Trademark Notice Iridium and the Iridium logo are registered trademarks and/or service marks of Iridium Satellite LLC. Windows, Windows 95, Windows 98, Windows Me, Windows NT, Windows 2000, Dial-Up Networking, Outlook, Outlook Express and Internet Explorer are registered trademarks of Microsoft Corporation.
