Quick Reference Manual

2
English
RF Energy Exposure and Product Safety Guide for
Body Worn Camera
The Si200 is only designed for video recording. Before using this product
read the RF Energy Exposure Training and Product Safety Information for
Mission Critical Devices which contains instructions for safe usage and RF
energy awareness and control for compliance with applicable standards
and regulation. Use only power supplies listed in this user guide.
This equipment is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
For body worn operation, this device has been tested and meets the FCC
RF exposure guideline for use with Motorola Solutions, Inc. approved
accessories sold with this device.
The device for operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
When used in Canada for 5 GHz WLAN, the following restrictions is
applicable:
Notched Band 5.6 - 5.65 GHz
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only
for indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the
bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the
band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits specified for point-to-point and
non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant
with the e.i.r.p. elevation mask requirement set forth in Section
6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN devices.
Radio Frequency Interference Requirements - FCC
Notice: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device
signifying that the radio(s) is/are approved for use in the US. Operation
of the device without regulatory approval is illegal.
to correct the interference by one or more of the following
measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Use of non-Motorola-approved body worn camera or battery accessories
may exceed the applicable RF exposure guidelines (iEEE, ICNIRP or
FCC). This device complies with part 15 of the FCC Rules and Industry
Canada license exempt RSS standard(s). Operation is subject to the
following three conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. (3) Any
changes or modifications not expressly approved by Motorola Solutions
may void the user's authority to operate this device. This class B digital
apparatus complies with Canadian ICES-003.
Under Industry Canada regulations, this microphone transmitter may
only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
This device complies with the Canada portable RF exposure limit set
forth for an uncontrolled environment and is safe for intended operation
as described in this manual. Further RF exposure reduction can be
achieved if the product is kept as far as possible from the user’s body or
setting the device to a lower output power, if such function is available.
Frequency of Operation - IC 2.4 & 5 GHz