Network Router User Manual
Table Of Contents
- Copyright
- Table of Contents
- Introduction
- CHAPTER 1 Overview of Major Capabilities
- CHAPTER 2 Basic Mode Setup
- CHAPTER 3 Advanced Setup
- Access the Expert Web Interface
- Links Bar
- Link: Configure
- Link: Connection
- Link: DHCP Server
- Link: IP Passthrough
- Link: NAT
- Link: IPSec
- IPSec VPN
- Link: Router Password
- Link: Time Zone
- Link: VLAN
- Overview
- Ethernet Switching/Policy Setup
- Link: Wireless
- Enable Wireless
- Wireless ID (SSID)
- Privacy
- Advanced Configuration Options (optional)
- WiFi Multimedia
- Wireless MAC Authorization (optional)
- Link: Status
- DSL
- ATM
- Ethernet
- IP
- LAN
- Wireless
- USB
- Logs
- User List
- Link: Diagnostics
- Link: Remote Access
- Link: Update Router
- From a Server
- Link: Reset Router
- Link: Restart Router
- Basic Mode
- Help
- CHAPTER 4 Basic Troubleshooting
- CHAPTER 5 Command Line Interface
- Overview
- Starting and Ending a CLI Session
- Using the CLI Help Facility
- About SHELL Commands
- SHELL Commands
- About CONFIG Commands
- CONFIG Commands
- Remote ATA Configuration Commands
- DSL Commands
- Bridging Settings
- DHCP Settings
- DMT Settings
- Domain Name System Settings
- IGMP Settings
- IP Settings
- Queue Configuration
- IPMaps Settings
- Network Address Translation (NAT) Default Settings
- Network Address Translation (NAT) Pinhole Settings
- PPPoE /PPPoA Settings
- PPPoE with IPoE Settings
- Ethernet Port Settings
- 802.3ah Ethernet OAM Settings
- Command Line Interface Preference Settings
- Port Renumbering Settings
- Security Settings
- SNMP Settings
- System Settings
- Syslog
- Wireless Settings (supported models)
- VLAN Settings
- VoIP settings
- UPnP settings
- DSL Forum settings
- Backup IP Gateway Settings
- VDSL Settings
- CHAPTER 6 Glossary
- Index
252
Port Renumbering Settings
If you use NAT pinholes to forward HTTP or telnet traffic through your Motorola Netopia®
Gateway to an internal host, you must change the port numbers the Motorola Netopia®
Gateway uses for its own configuration traffic. For example, if you set up a NAT pinhole to
forward network traffic on Port 80 (HTTP) to another host, you would have to tell the Motor-
ola Netopia® Gateway to listen for configuration connection requests on a port number
other than 80, such as 6080.
After you have changed the port numbers the Motorola Netopia® Gateway uses for its con-
figuration traffic, you must use those port numbers instead of the standard numbers when
configuring the Motorola Netopia® Gateway. For example, if you move the router's Web ser-
vice to port “6080” on a box with a system (DNS) name of “superbox”, you would enter the
URL http://superbox:6080 in a Web browser to open the Motorola Netopia® Gateway
graphical user interface. Similarly, you would have to configure your telnet application to
use the appropriate port when opening a configuration connection to your Motorola Neto-
pia® Gateway.
set servers web-http [ 1 - 65534 ]
Specifies the port number for HTTP (web) communication with the Motorola Netopia® Gate-
way. Because port numbers in the range 0-1024 are used by other protocols, you should
use numbers in the range 1025-65534 when assigning new port numbers to the Motorola
Netopia® Gateway web configuration interface. A setting of 0 (zero) will turn the server off.
set servers telnet-tcp [ 1 - 65534 ]
Specifies the port number for telnet (CLI) communication with the Motorola Netopia® Gate-
way. Because port numbers in the range 0-1024 are used by other protocols, you should
use numbers in the range 1025-65534 when assigning new port numbers to the Motorola
Netopia® Gateway telnet configuration interface. A setting of 0 (zero) will turn the server
off.
☛ NOTE:
You cannot specify a port setting of 0 (zero) for both the web and telnet ports
at the same time. This would prevent you from accessing the Gateway.