Two-Way Radios User Guide RMU2080 & RMV2080 Non-Display models
Open Source Software Legal Notices: This Motorola product contains Open Source Software. For information regarding licenses, acknowledgements, required copyright notices and other usage terms, refer to the documentation for this Motorola product at: http://businessonline.motorolasolutions.com Go to: Resource Center > Product Information > Manual > Accessories.
CONTENTS 1 14 15 16 16 17 17 18 19 21 22 24 26 26 26 26 26 27 27 29 30 CONTENTS Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Product Safety . . . . . . . . . . . . . . . . . . . . . . . .4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .5 Package Contents . . . . . . . . . . . . . . . . . . . . . .5 FCC Licensing Information . . . . . . . . . . . . .7 Interference Information . . . . . . . . . . . . . . . . .7 Batteries and Chargers Safety Information. . . . . . . .
CONTENTS English With Compatible VOX Accessories. . . . .30 Setting VOX Sensitivity . . . . . . . . . . . . . .30 Microphone Gain. . . . . . . . . . . . . . . . . . .31 Hands Free without Accessories (iVOX) . . . . . . . . . . . . . . . . . . . . . . . . .31 Toggle Voice Prompt in User Mode . . . .31 Power Up - Tone Mode. . . . . . . . . . . . . .31 Reset to Factory Defaults . . . . . . . . . . . .31 Programming Features . . . . . . . . . . . . . . . .32 Advanced Configuration Mode . . . . . . . . . . .
Software Applications. . . . . . . . . . . . . . . . . . RM Series™ Features Summary. . . . . . . . New Features . . . . . . . . . . . . . . . . . . . . . . . Programmable Buttons Chart . . . . . . . . . . 75 77 86 88 CONTENTS (Optional Accessory). . . . . . . . . . . . . .49 Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory). . . . . . . . . . . . . .50 Cloning using the Customer Programming Software (CPS) . . . . . .52 Troubleshooting . . . . . . . . . . . . . . . . . . . .
PRODUCT SAFETY PRODUCT SAFETY PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE ! Caution Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION! This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements.
INTRODUCTION Business Radios, Mailstop 1C15, Motorola Thank you for purchasing the Motorola® RM Series™ Radio. This radio is a product of Motorola's 80 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RM Series™ radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more.
INTRODUCTION For a copy of a large-print version of this user guide or for product-related questions, contact English 1-800-448-6686 in the USA 1-800-461-4575 in Canada 1-888-390-6456 on TTY (Text Telephone) For product related information, visit us at: www.motorolasolutions.
To transmit on these frequencies, you are FCC LICENSING INFORMATION required to have a license issued by the FCC. Application is made available on FCC Form This device complies with Part 15 of the FCC 601 and Schedules D, H, and Remittance Form 159. Rules. Operation is subject to the condition that To obtain these FCC forms, request document this device does not cause harmful 000601 which includes all forms and interference. instructions.
FCC LICENSING INFORMATION Before filling out your application, you must Replacement of any transmitter component decide which frequency(ies) you can operate (crystal, semiconductor, etc.) not authorized by on. See “Frequencies and Code Charts”. For the FCC equipment authorization for this radio questions on determining the radio frequency, could violate FCC rules.
3. and cord, pull by the plug rather than the cord when disconnecting the charger. 4. extension cord could result in risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18AWG Before using the battery charger, read all the instructions and cautionary markings on the charger, • the battery, and • the radio using the battery 1. To reduce risk of injury, charge only the for lengths up to 100 feet (30.48 m), and 16AWG for lengths up to 150 feet (45.72 m).
BATTERIES AND CHARGERS SAFETY INFORMATION OPERATIONAL SAFETY GUIDELINES • Turn the radio OFF when charging battery. • The charger is not suitable for outdoor use. Use only in dry locations/conditions. • Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product). • Disconnect charger from line voltage by removing main plug.
RADIO OVERVIEW PARTS OF THE RADIO Antenna On/Off/Volume Knob Audio Accessory 2 Pin Connector Battery Model Label RMU2080 Microphone LED Indicator PTT (Push-ToTalk) Button RADIO OVERVIEW Channel Selector Knob SB1 - Monitor Button SB2 - Scan/ Nuisance Channel Delete 11 English
RADIO OVERVIEW On/Off/Volume Knob Side Buttons Used to turn the radio ON or OFF and to adjust the radio’s volume. Push-to-Talk (PTT) Button Channel Selector Knob Used to switch the radio to different channels. Press and hold down this button to talk, release it to listen. Side Button 1 (SB1) • Accessory Connector Used to connect compatible audio accessories. The Side Button 1 is a general button that can be configured by the Customer Programming Software - CPS.
Table 1: RM Series Radio Specifications Model Frequency Band Transmit Power (Watts) Number of Channels Antenna RMU2080 UHF 2 8 Non-removable RMV2080 VHF 2 8 Non-removable 13 RADIO OVERVIEW This User Guide covers multiple RM Series models, and may detail some features your radio does not have.
RADIO OVERVIEW BATTERY FEATURES English RM Series radios provide Lithium-Ion batteries that come in different capacities that defines the battery life. About the Li-Ion Battery The RM Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be fully charged before initial use to ensure optimum capacity and performance. Battery life is determined by several factors.
Battery Recycling and Disposal Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at: www.rbrc.com or call: 1-800-8-BATTERY This internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies. 15 RADIO OVERVIEW Li-Ion rechargeable batteries can be recycled.
Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery Detach Press Latch RADIO OVERVIEW Attach Press until click Tabs Slots 1. Turn OFF the radio. 1. Turn OFF the radio. 2. With the Motorola logo side up on the battery 2. Push down the battery latch and hold it while pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radio’s body. 3. Press the top part of the battery towards the radio until a click is heard.
Holster Power Supply, Adaptor and Drop-in Tray Charger 1. Insert the radio into the base of the holster at an angle. Press the radio against the back of the Power Supply The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For more information, refer to “Chargers” on page 74. RADIO OVERVIEW Drop-in Tray Charger holster until the hooks on the holster are inserted in the top recesses of the battery. 2.
Battery Life Information RADIO OVERVIEW When the Battery Save feature is set to ON (enabled by default), the battery life lasts longer. The following table summarizes battery life estimations: English Table 2: Li-Ion Battery Life with Tx Power 2 Watts Note: Battery Type Battery Save OFF Battery Save ON Standard 12 Hours 15 Hours High Capacity N/A N/A Battery life is estimated based on 5% transmit / 5% receive / 90% standby standard duty cycle.
Charging the Battery The RM Series radio offers two types of Power Supplies: Standard Power Supply and, • Rapid Power Supply Note: Drop-in Tray SUC Port Power Supply (Transformer) RADIO OVERVIEW • Charging with the Drop-in Tray Single Unit Charger (SUC) The radio comes with a Standard Power Supply. To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger. Drop-in Tray SUC 1.
RADIO OVERVIEW Note: When charging a battery attached to the radio, turn the radio OFF to ensure a full charge. See “Operational Safety Guidelines” on page 10 for more information. Charging A Stand-Alone Battery Table 3: Motorola Authorized Batteries Part Number To charge only the battery - at step 4 on page 19, insert the battery into the tray, with the inside surface of the battery facing the front of the Drop-in Tray Single Unit Charger as shown English above.
Drop-in Tray Charger LED Indicators Table 4: Charger LED Indicator Status LED Indicator Green for approximately 1 second Charging Steady Red Charging Complete Steady Green Battery Fault (*) Red Fast Flash Waiting to Charge (**) Amber Slow Flash Battery Level Status N/A Battery empty Flash Red 1 Time Battery low Flash Amber 2 Times Battery medium Flash Green 3 Times Battery High RADIO OVERVIEW Power On Comments (*) Normally, re-positioning the battery pack will correct this issue.
If there is NO LED indication: 1. Check if the radio with battery, or the battery alone, is inserted correctly. (refer to step 4 of "Charging with the 2. Ensure that the power supply cable is securely plugged into the charger socket using an appropriate AC 3. Confirm that the battery being used with the radio is listed in Table 3 on page 20. RADIO OVERVIEW Drop-in Tray Single Unit Charger (SUC)" on page 19) outlet and there is power to the outlet.
Charging a Radio and Battery using a Multi Unit-Charger - MUC (Optional Accessory) 1. Place the Multi-Unit Charger on a flat surface. 2. Insert the power cord plug into the MUC’s dual 3. Plug the power cord into an AC outlet. 4. Turn the radio OFF. 5. Insert the radio or battery into the charging pin connector at the bottom of the MUC. RADIO OVERVIEW pocket with the radio or battery facing away from the contacts.
Multi-Unit Charger LED Indicators RADIO OVERVIEW Table 6: Charger LED Indicator Status LED Indicator Power On Green for approximately 1 second Charging Steady Red Charging Complete Steady Green Battery Fault (*) Red Fast Flash Waiting to Charge (**) Amber Slow Flash Battery Level Status Comments N/A Battery empty Flash Red 1 Time Battery low Flash Amber 2 Times Battery medium Flash Green 3 Times Battery High (*) Normally, re-positioning the battery pack will correct this issue.
If there is NO LED indication: 1. Check if the radio with battery or the battery alone, is inserted correctly (refer to step 5 of "Charging a Radio and Battery using a Multi RADIO OVERVIEW Unit-Charger - MUC (Optional Accessory)" on page 23). 2. Make sure the power cord is securely plugged into the MUC and the appropriate AC outlet. Make sure there is power to the AC outlet. 3. Confirm that the battery being used with the radio is listed in Table 3 on page 20.
GETTING STARTED GETTING STARTED For the following explanations, refer to “Parts Of The Radio” on page 11. TURNING RADIO ON/OFF To turn ON the radio, rotate the On/Off/Volume Knob clockwise. The radio plays one of the following: • Power up tone and channel number announcement, or • Battery level and channel number announcements, or • Silent (Audible tones disabled) The LED blinks red briefly.
Notes: • TALK RANGE To listen to all activity on a current channel, short TALK RANGE press the SB1 to set the CTCSS/DPL code to 0. (Squelch set to SILENT)’. • Model (*) This assumes SB1 is not being programmed for a different mode. RECEIVING A CALL 1. Industrial Multi-Level Inside steel/ concrete Industrial buildings Inside multilevel buildings UHF 2W Up to 250,000 Sq. Ft. Up to 20 Floors VHF 2W Up to 220,000 Sq. Ft.
GETTING STARTED English To establish a proper two-way communication, the channel, frequency, and interference eliminator codes must be the same on both radios. This depends on the stored profile that has been preprogrammed on the radio: 1. Channel: Current channel that the radio is using, depending on radio model. 2. Frequency: The frequency the radio uses to 3. Interference Eliminator Code: These codes transmit/receive. help minimize interference by providing a choice of code combinations. 28 4.
RADIO LED INDICATORS RADIO STATUS LED INDICATION Solid Orange Cloning Mode Double Orange Heartbeats Cloning In Progress Solid Orange Fatal Error at Power up One Green Blink, One Orange Blink, One Green Blink, then repeat for 4 seconds Low Battery Orange Heartbeat Low Battery Shutdown Fast Orange Heartbeat Monitor LED is OFF Power-Up Solid Red for 2 seconds ‘Idle’ Programming Mode / Channel Mode Green Heartbeat Scan Mode Fast Red Heartbeat Transmit (Tx)/Receive (RX) Solid Red Transmit i
HANDS-FREE USE/VOX 2. Open accessory cover. 3. Insert the audio accessory’s plug firmly into 4. Turn radio ON. The LED Indicator will blink 5. Lower radio volume BEFORE placing 6. To transmit, speak into accessory microphone 7. VOX can be temporarily disabled by pressing GETTING STARTED accessory port. double red accessory near ear. Accessory Port/ Connector VOX Accessory Motorola RM Series™ radios can operate hands-free (VOX) when used with compatible VOX accessories.
Default value is OFF. If you want to use the VOX feature, VOX level should be set at a different level. Toggle Voice Prompt in User Mode 1 = High audio input level will trigger the Tx • 2 = Medium sensitivity Note: • 3 = Low audio input level will trigger the Tx This setting is set to OFF by default and must be enabled using the CPS. Microphone Gain Power Up - Tone Mode The sensitivity of the microphone can be adjusted to fit different users or operating environments.
PROGRAMMING FEATURES PROGRAMMING FEATURES To easily program all the features in your radio, it is recommended to use the Customer Programming Software (CPS) and the programming cable. Auto-Scan, • Active Channels, and • Enable/Disable/Program the Weather Channel The Frequencies Select feature allows you to choose frequencies from a pre-defined list.
Entering Advanced Configuration Mode Note: Before configuring the features, make sure your radio is set to the channel you wish to program. You can do so before entering Advanced Configuration Mode or at any time during the Advanced Configuration Mode by rotating the Channel Selector Knob until you reach the desired channel.
PROGRAMMING FEATURES Reading CTCSS / DPL Values Active Channels Cycle through the features available for configuration by short pressing the PTT button until you hear the current code. The radio moves to the programming CTCSS/PL codes mode. While in Auto-Scan mode, short pressing the PTT button shifts the radio to ‘Active Channels’ feature. Enter a new code value using the SB1 and SB2 buttons. Weather Channel Programming The RM Series radios have up to 219 codes available.
Programming Mode and return to the normal PROGRAMMING FEATURES radio operation. Note: • To exit the programming mode without saving, turn OFF the radio. • If you ‘roll-over’ to the beginning of ‘Idle’ Programming Mode, you will hear “Channel Number” and the LED Indicator blinks green again. All changed values will be automatically saved.
PROGRAMMING FEATURES Programming Mode FAQ 1. I got distracted while programming and forgot which feature I was programming. What should I do? Return to ‘Idle’ Programming Mode and start over. You will not be able to return to Programming Mode (the radio does not provide further way to let you know the specific stage you are at in the Programming Mode). Therefore you can: 3. I am trying to enter the Programming Mode but the radio would not do it. • Long press the PTT button.
• Turn OFF the radio and start over. I just programmed the value I wanted. How do I exit the Programming Mode? You can either: • long press the PTT button twice to exit if you’re in • Long press the PTT button once if you are the Programming Mode or, already in the ‘Idle’ Programming mode. 6. PROGRAMMING VALUES EXAMPLE Example of Programming a Frequency Assuming current frequency value is set to Channel 1, with the UHF default frequency set to ‘02’ (equivalent to 464.
PROGRAMMING FEATURES Example of Programming a Code Example of Programming Auto-Scan Assuming the current code value is set to factory default ‘001’, and you want to change it to CTCSS/DPL Code = 103. Follow the sequence indicated below: Auto-Scan is the third available feature in the Programming Mode and can be set to either ON or OFF on a particular channel. 1. Enter Advanced Configuration Mode. 2. Short press the PTT button twice.
Example of Programming Active Channels To set Active Channels: • Enter Advanced Configuration Mode and select the desired channel. • Example of Programming Weather Channels Weather Channels is the last Programming mode. It allows you to toggle a radio channel between 2 way radio mode and weather alert mode.
PROGRAMMING FEATURES OTHER PROGRAMMING FEATURES seconds, scanning resumes. Scan Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it stops scanning and goes to the active channel. This allows you to listen and talk to people in that channel without having to change channel manually. If there are transmissions on another channel, you will not hear that activity once the radio has stopped scanning.
Nuisance Channel Delete CUSTOMER PROGRAMMING SOFTWARE (CPS) Radio to be programmed To delete a channel from the Scan List: • Start Scan mode by short pressing the SB1 or SB2 (programmed for scan) button. • USB Ports Wait until the radio stops at the channel you wish CPS Programming Cable to eliminate. Long press the SB2 button to delete it. You cannot delete the channel with scan enabled (home channel).
PROGRAMMING FEATURES To program, connect the RM Series radio via the Drop-in Charger Tray and CPS Programming Cable as shown in Figure 1 on page 41. Toggle the cable switch of the CPS Programming Cable to ‘CPS Mode’. CPS allows you to program frequencies, PL/ DPL Codes as well as other features such as: Bandwidth Select, Time-out Timer, Power Select, Scan List, Call Tones, Scramble, Reverse Burst, etc.
Scramble PROGRAMMING FEATURES The Scramble feature makes transmissions sound garbled to anyone listening without the same code. Scramble default value is OFF. To change the scramble code during radio’s normal operation, the Scramble feature must be programmed to either SB1 or SB2. Reverse Burst Reverse Burst eliminates unwanted noise (squelch tail) during loss of carrier detection. You can select values of either 180 or 240 to be compatible with other radios. The default value is 180.
PROGRAMMING FEATURES WEATHER CHANNEL English NOAA Weather Radio All Hazards (NWR) is a nationwide network of radio stations broadcasting continuous weather information directly from the nearest National Weather Service office. NWR broadcasts official Weather Service warnings, watches, forecasts and other hazard information 24 hours a day, 7 days a week.
button to advance to channel menu or weather menu alert menu. The NOAA Weather Radio feature can be disabled or configured to any of the other available channel positions via the Customer Programming Software (CPS) or in Advanced Configuration Mode. When a channel that has the NOAA Weather Radio is selected, the RM radio generates an audible voice announcement indicating the channel and weather frequency number. (E.g.: “Channel 8: Weather 1”).
PROGRAMMING FEATURES English detected. While monitoring an alert, pressing the PTT button or changing channels exits the weather alert and returns to normal operation. Note: Using the Weather Alert Feature impacts normal battery life.
CLONING RADIOS You can clone RM Series radio profiles from one Source radio to a Target radio by using any one of these 3 methods: • a Source radio (radio which profiles will be cloned • • a Target radio (the radio which profile will be Using a Multi Unit Charger (MUC- optional or copied from) and cloned from the source radio.
PROGRAMMING FEATURES simultaneously while turning the radio ON. • Wait for 3 seconds before releasing the buttons until the audible tone “Cloning” is heard. 3. Place the Source radio in the source pocket that pairs with the target pocket you chose in step 1. Notes: • If cloning fails, refer to “What To Do If Cloning • Paired Target radios and Source radios must be Fails” on page 51. of the same band type in order for the cloning to Press and release the SB1 button. 4.
• CPS Cable PROGRAMMING FEATURES CPS and Cloning Cables (Optional Accessory) Both CPS and Cloning Cables are made to work either with RM Series radios or RDX Series radios. Cloning cable supports a mix of RM and RDX series radios. • CPS cable programs RM series radios. Make sure the cable switch is in “Flash” position. To Cloning Cable program a RDX radio with the CPS cable, make sure the cable switch is in “CPS” position and the USB converter provided in the CPS cable kit is attached to the cable.
PROGRAMMING FEATURES Cloning Radio using the Radio to Radio (R2R) Cloning Cable (Optional Accessory) Unplug any cables (power supply or USB cables) from the SUCs. 3. Plug one side of the cloning cable mini USB connector to the first SUC and the other end to the second SUC. Note: During the cloning process, no power is being applied to the SUC. The batteries will not be charged. Only data communication is being established between the two radios. 4. Turn ON the Target Radio and place it into one 5.
(cloning is successful) or “fail” (cloning process 4. model radio, it will either show ‘Pass’ or ‘Fail’ on the display (a voice announcement will be played within 5 seconds). 8. Once the cloning process is completed, turn the tray or on the radio contacts. 5. Ensure that the Target radio is turned ON. 6. Ensure that the Source radio is in cloning mode. 7.
PROGRAMMING FEATURES English Cloning using the Customer Programming Software (CPS) When cloning using this method, you need the CPS software, a Drop-In Tray Charger and the CPS Programming Cable. Radio to be programmed To order the CPS Programming Cable, please refer to P/N# HKKN4028_. Information on how to clone using the CPS is available either in: • the CPS Help File --> Content and Index --> Cloning Radios, or • in the CPS Programming Cable Accessory Leaflet.
TROUBLESHOOTING Try This... Recharge or replace the Li-Ion battery. No Power Extreme operating temperatures may affect battery life. Refer to “About the Li-Ion Battery” on page 14 Confirm Interference Eliminator Code is set. Hearing other noises or conversation on a channel Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting.
Symptom Try This... TROUBLESHOOTING Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Limited talk range Change location of radio. To increase range and coverage, you can reduce obstructions or increase power. UHF radios provides greater coverage in industrial and commercial buildings.
Symptom Try This... Radios are too close; they must be at least five feet apart. Radios are too far apart or obstacles are interfering with transmission. TROUBLESHOOTING Heavy static or interference Refer to “Talking and Monitoring” on page 26. Recharge or replace Li-Ion battery. Low batteries Extreme operating temperatures affect battery life. Refer to “About the Li-Ion Battery” on page 14.
Symptom Try This... TROUBLESHOOTING VOX feature might be set to OFF. English Cannot activate VOX Use the CPS to ensure that the VOX Sensitivity level is not set to ‘0’. Accessory not working or not compatible. Refer to “Hands-Free Use/VOX” on page 30. Check drop-in tray charger is properly connected and correspond to a Battery does not charge although it has been placed in the drop-in charger for a while compatible power supply.
USE AND CARE Do not immerse in water Do not use alcohol or cleaning solutions If the radio is submerged in water...
FREQUENCY AND CODE CHARTS FREQUENCY AND CODE CHARTS English RM VHF FREQUENCIES CHART The charts in this section provide Frequency and Code information. These charts are useful when using the Motorola RM Series two-way radios with other business radios. VHF Frequencies – BRUS Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth 1(*) 2(*) 151.6250 151.9550 12.5 kHz 12.5 kHz 15(*) 16 151.7750 151.8650 12.5 kHz 12.5 kHz 3 152.8850 12.5 kHz 17 151.8950 12.5 kHz 4 152.
RMV2080 – VHF DEFAULT FREQUENCIES CHART FREQUENCY AND CODE CHARTS RM VHF 8CH Radios Default Frequencies – RMV2080 Channel Frequency # Frequency (MHz) Code Bandwidth 1 20 154.4900 67.0 Hz 12.5 kHz 2 21 154.5150 67.0 Hz 12.5 kHz 3 1 151.6250 67.0 Hz 12.5 kHz 4 2 151.9550 67.0 Hz 12.5 kHz 5 10 151.5125 67.0 Hz 12.5 kHz 6 12 151.6850 67.0 Hz 12.5 kHz 7 15 151.7750 67.0 Hz 12.5 kHz WC 162.4000 67.0 Hz 12.
FREQUENCY AND CODE CHARTS RM UHF FREQUENCIES CHART English RM UHF Frequencies Frequency # Frequency (MHz) Bandwidth Frequency # Frequency (MHz) Bandwidth 1 464.5000 12.5 kHz 15 461.1875 12.5 kHz 2 464.5500 12.5 kHz 16 461.2125 12.5 kHz 3 467.7625 12.5 kHz 17 461.2375 12.5 kHz 4 467.8125 12.5 kHz 18 461.2625 12.5 kHz 5 467.8500 12.5 kHz 19 461.2875 12.5 kHz 6 467.8750 12.5 kHz 20 461.3125 12.5 kHz 7 467.9000 12.5 kHz 21 461.3375 12.5 kHz 8 467.9250 12.
RM UHF Frequencies (Continued) Frequency # Frequency (MHz) Bandwidth 29 462.9125 12.5 kHz 47 466.3625 12.5 kHz 30 464.4875 12.5 kHz 48 467.7875 12.5 kHz 31 464.5125 12.5 kHz 49 467.8375 12.5 kHz 32 464.5375 12.5 kHz 50 467.8625 12.5 kHz 33 464.5625 12.5 kHz 51 467.8875 12.5 kHz 34 466.0375 12.5 kHz 52 467.9125 12.5 kHz 35 466.0625 12.5 kHz 53 469.4875 12.5 kHz 36 466.0875 12.5 kHz 54 469.5125 12.5 kHz 37 466.1125 12.5 kHz 55 469.5375 12.5 kHz 38 466.
FREQUENCY AND CODE CHARTS RM UHF Frequencies (Continued) Frequency # Frequency (MHz) Bandwidth Note: English Frequency # Frequency (MHz) Bandwidth 65 451.1875 12.5 kHz 78 456.1875 12.5 kHz 66 451.2375 12.5 kHz 79 456.2375 12.5 kHz 67 451.2875 12.5 kHz 80 456.2875 12.5 kHz 68 451.3375 12.5 kHz 81 456.3375 12.5 kHz 69 451.4375 12.5 kHz 82 456.4375 12.5 kHz 70 451.5375 12.5 kHz 83 456.5375 12.5 kHz 71 451.6375 12.5 kHz 84 456.6375 12.5 kHz 72 452.3125 12.
RMU2080 – UHF DEFAULT FREQUENCIES CHART Channel Frequency # Frequency (MHz) Code # Code Bandwidth 1 2 464.5500 1 67.0 Hz 12.5 kHz 2 8 467.9250 1 67.0 Hz 12.5 kHz 3 5 467.8500 1 67.0 Hz 12.5 kHz 4 6 467.8750 1 67.0 Hz 12.5 kHz 5 10 461.0625 1 67.0 Hz 12.5 kHz 6 12 461.1125 1 67.0 Hz 12.5 kHz 7 14 461.1625 1 67.0 Hz 12.5 kHz WC 162.4000 1 67.0 Hz 12.
CTCSS AND PL/DPL CODES FREQUENCY AND CODE CHARTS CTCSS Codes CTCSS Hz CTCSS Hz CTCSS Hz 1 67.0 14 107.2 27 167.9 2 71.9 15 110.9 28 173.8 179.9 3 74.4 16 114.8 29 4 77.0 17 118.8 30 186.2 5 79.7 18 123 31 192.8 6 82.5 19 127.3 32 203.5 7 85.4 20 131.8 33 210.7 8 88.5 21 136.5 34 218.1 9 91.5 22 141.3 35 225.7 10 94.8 23 146.2 36 233.6 11 97.4 24 151.4 37 241.8 12 100.0 25 156.7 38 250.3 103.5 26 162.2 122 (*) 69.
DPL Code DPL Code DPL Code 39 23 55 116 71 243 40 25 56 125 72 244 41 26 57 131 73 245 42 31 58 132 74 251 261 43 32 59 134 75 44 43 60 143 76 263 45 47 61 152 77 265 46 51 62 155 78 271 47 54 63 156 79 306 48 65 64 162 80 311 49 71 65 165 81 315 50 72 66 172 82 331 51 73 67 174 83 343 52 74 68 205 84 346 53 114 69 223 85 351 54 115 70 226 86 364 FREQUENCY AND CODE CHARTS PL/DPL Codes 65 English
FREQUENCY AND CODE CHARTS PL/DPL Codes (Continued) English DPL Code DPL Code DPL Code 87 365 104 565 121 754 88 371 105 606 123 645 89 411 106 612 124 Customized PL 90 412 107 624 125 Customized PL 91 413 108 627 126 Customized PL 92 423 109 631 127 Customized PL 93 431 110 632 128 Customized PL 94 432 111 654 129 Customized PL 95 445 112 662 130 Inverted DPL 39 96 464 113 664 131 Inverted DPL 40 97 465 114 703 132 Inverted DPL 41 98
PL/DPL Codes (Continued) Code DPL Code DPL Code 139 Inverted DPL 48 156 Inverted DPL 65 173 Inverted DPL 82 140 Inverted DPL 49 157 Inverted DPL 66 174 Inverted DPL 83 141 Inverted DPL 50 158 Inverted DPL 67 175 Inverted DPL 84 142 Inverted DPL 51 159 Inverted DPL 68 176 Inverted DPL 85 143 Inverted DPL 52 160 Inverted DPL 69 177 Inverted DPL 86 144 Inverted DPL 53 161 Inverted DPL 70 178 Inverted DPL 87 145 Inverted DPL 54 162 Inverted DPL 71 179 Inverted DPL 8
FREQUENCY AND CODE CHARTS PL/DPL Codes (Continued) English DPL Code DPL Code DPL Code 190 Inverted DPL 99 200 Inverted DPL 109 210 Inverted DPL 119 191 Inverted DPL 100 201 Inverted DPL 110 211 Inverted DPL 120 192 Inverted DPL 101 202 Inverted DPL 111 212 Inverted DPL 121 193 Inverted DPL 102 203 Inverted DPL 112 213 Inverted DPL 123 194 Inverted DPL 103 204 Inverted DPL 113 214 Customized DPL 195 Inverted DPL 104 205 Inverted DPL 114 215 Customized DPL 196 Inv
Notes FREQUENCY AND CODE CHARTS English 69
MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA English MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA What Does this Warranty Cover? Subject to the exclusions contained below, Motorola, Inc.
Exclusions Use of Non-Motorola Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, or its authorized service centers, are excluded from coverage. Altered Products.
MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage. Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CDROM, or floppy disk). Length of Coverage Ninety (90) days from the date of purchase.
EXPORT LAW ASSURANCES This product is controlled under the export regulations of the United States of America. The Governments of the United States of America may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce. PATENT NOTICE This product is covered by one or more of the following United States patents.
ACCESSORIES Part No. ACCESSORIES AUDIO ACCESSORIES English Part No. BATTERY Description Description PMNN4434_R Standard Li-Ion Battery PMNN4453_R High Capacity Li-Ion Battery 53815 Headset w/Boom Mic BR HMN9026_R Remote Speaker Mic BR HKLN4477_ Surveillance Earpiece BR 53865 Headset w/Swivel Boom Mic HKKN4028_ Radio to Radio Cloning Cable 53866 Earbud w/Clip PTT Mic BR HKKN4027_ CPS Programming Cable 56517 Earpiece w/Inline Mic RLN6423_ Swivel Earpiece BR 74 CABLES Part No.
CARRY ACCESSORIES Part No. HKLN4510_ Description Swivel Holster ACCESSORIES SOFTWARE APPLICATIONS Part No.
ACCESSORIES Notes English 76
m Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All rights reserved.
