User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

Table Of Contents

Foreword
- General Safety Precautions
- Computer Software Copyrights
- Document Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
MOTOTRBO SLR 5000 Series Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Warranty
SLR 5000 Series Repeater
- 1.1 Notations Used in This Manual
- 1.2 Description
- 1.3 Operating Features
- 1.4 Frequency Ranges and Power Levels
- 1.5 Specifications
- 1.6 Theory of Operation
- 1.7 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.8 Repeater Model Numbering Scheme
- 1.9 Model Chart
SLR 5000 Series Satellite Receiver
- 2.1 Description
- 2.2 Operating Features
- 2.3 Frequency Ranges
- 2.4 Specifications
- 2.5 Configuration
- 2.6 Basic Station Level Troubleshooting – RDAC and LEDs
- 2.7 Model Chart
SLR 5000 Series Modem
- 3.1 Description
- 3.2 Receiver Subsystem
  - 3.2.1 Specifications
- 3.3 Transmitter Exciter Subsystem
  - 3.3.1 Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 High Stability Reference Block
  - 3.4.2 Audio
- 3.5 Station Control Interface
SLR 5000 Series Power Amplifier
- 4.1 Description
  - 4.1.1 General Description
- 4.2 Input and Output Connections
- 4.3 Frequency Ranges
- 4.4 Specifications
- 4.5 Modem Interface
SLR 5000 Series Power Supply
- 5.1 Description
  - 5.1.1 General Description
- 5.2 Specifications
- 5.3 Power Supply Interface
SLR 5000 Series Front Panel
- 6.1 Description
  - 6.1.1 General Description
- 6.2 Input and Output Connections
- 6.3 Interfaces
  - 6.3.1 Modem Interface
  - 6.3.2 User/Service Interface
    - 6.3.2.1 USB
    - 6.3.2.2 LED Indicators
SLR 5000 Series Back Panel
- 7.1 Description
  - 7.1.1 General Description
- 7.2 Back panel Interfaces
SLR 5000 Series Test Equipment And Service Aids
- 8.1 Recommended Test Equipment
- 8.2 Service Aids
SLR 5000 Series Performance Check or Testing
- 9.1 General
- 9.2 Transmitter Testing
- 9.3 Receiver Testing
- 9.4 Auto Test and Tune Support
SLR 5000 Series Programming and Tuning
- 10.1 Introduction
- 10.2 Customer Programming Software Setup
- 10.3 Reference Oscillator Alignment
  - 10.3.1 Tuning the Reference Oscillator Alignment
- 10.4 Repeater Tuning Setup
- 10.5 Rx Audio Level Set
  - 10.5.1 Tuning the Rx Audio Level Set
- 10.6 Tx Audio Level Set
  - 10.6.1 Tuning the Tx Audio Level Set
- 10.7 Modulation Limit Alignment
- 10.8 Changing to Battery Charger Only Mode
SLR 5000 Series Maintenance and Disassembly/Reassembly
- 11.1 Introduction
- 11.2 Routine Maintenance
- 11.3 Preventive Maintenance
  - 11.3.1 Inspection
  - 11.3.2 Cleaning Procedures
- 11.4 Safe Handling of CMOS and LDMOS Devices
- 11.5 Disassembly
  - 11.5.1 Disassembly – General
  - 11.5.2 Disassembly – Detailed
- 11.6 Assembly and Reassembly
  - 11.6.1 Assembly – Detailed
    - 11.6.1.1 Back Panel Installation

Chapter 10

SLR 5000 Series Programming and

Tuning

10.1

Introduction

This chapter provides an overview of the MOTOTRBO Customer Programming Software (CPS) and

the MOTOTRBO Tuner application for use on Windows 7

™

, Windows 8

™

, or Windows 8.1

™

. These two

MOTOTRBO applications are used for the configuration and alignment of the SLR 5000 Series

Repeater.

10.2

Customer Programming Software Setup

The Customer Programming Software setup, shown in Figure 39: Customer Programming Software

Setup on page 89 is used to program the repeater. See Figure 40: Front view of SLR 5000 Series

Repeater on page 90 and Figure 41: Rear view of SLR 5000 Series Repeater on page 90 for the

actual connectors on the front and rear panels of the repeater.

NOTICE: See appropriate program on-line help files for the programming procedures.

CAUTION: Computer USB ports can be sensitive to Electronic Discharge. Employ proper ESD

practices (wrist strap, grounding, etc.) and do not touch exposed contacts on cables when

connected to a computer.

Figure 39: Customer Programming Software Setup

Front Panel

USB

120 / 240 VAC

Station

Tx Port

(N-type Female)

Rx Port

(BNC Female)

AUX

13.6 VDC

Standard Type “A” to Type “B” USB cable

Rear Panel

Either

One or Both

MN001436A01-AD

SLR 5000 Series Programming and Tuning

Send Feedback 89