User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

Table Of Contents

Foreword
- General Safety Precautions
- Computer Software Copyrights
- Document Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
MOTOTRBO SLR 5000 Series Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Warranty
SLR 5000 Series Repeater
- 1.1 Notations Used in This Manual
- 1.2 Description
- 1.3 Operating Features
- 1.4 Frequency Ranges and Power Levels
- 1.5 Specifications
- 1.6 Theory of Operation
- 1.7 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.8 Repeater Model Numbering Scheme
- 1.9 Model Chart
SLR 5000 Series Satellite Receiver
- 2.1 Description
- 2.2 Operating Features
- 2.3 Frequency Ranges
- 2.4 Specifications
- 2.5 Configuration
- 2.6 Basic Station Level Troubleshooting – RDAC and LEDs
- 2.7 Model Chart
SLR 5000 Series Modem
- 3.1 Description
- 3.2 Receiver Subsystem
  - 3.2.1 Specifications
- 3.3 Transmitter Exciter Subsystem
  - 3.3.1 Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 High Stability Reference Block
  - 3.4.2 Audio
- 3.5 Station Control Interface
SLR 5000 Series Power Amplifier
- 4.1 Description
  - 4.1.1 General Description
- 4.2 Input and Output Connections
- 4.3 Frequency Ranges
- 4.4 Specifications
- 4.5 Modem Interface
SLR 5000 Series Power Supply
- 5.1 Description
  - 5.1.1 General Description
- 5.2 Specifications
- 5.3 Power Supply Interface
SLR 5000 Series Front Panel
- 6.1 Description
  - 6.1.1 General Description
- 6.2 Input and Output Connections
- 6.3 Interfaces
  - 6.3.1 Modem Interface
  - 6.3.2 User/Service Interface
    - 6.3.2.1 USB
    - 6.3.2.2 LED Indicators
SLR 5000 Series Back Panel
- 7.1 Description
  - 7.1.1 General Description
- 7.2 Back panel Interfaces
SLR 5000 Series Test Equipment And Service Aids
- 8.1 Recommended Test Equipment
- 8.2 Service Aids
SLR 5000 Series Performance Check or Testing
- 9.1 General
- 9.2 Transmitter Testing
- 9.3 Receiver Testing
- 9.4 Auto Test and Tune Support
SLR 5000 Series Programming and Tuning
- 10.1 Introduction
- 10.2 Customer Programming Software Setup
- 10.3 Reference Oscillator Alignment
  - 10.3.1 Tuning the Reference Oscillator Alignment
- 10.4 Repeater Tuning Setup
- 10.5 Rx Audio Level Set
  - 10.5.1 Tuning the Rx Audio Level Set
- 10.6 Tx Audio Level Set
  - 10.6.1 Tuning the Tx Audio Level Set
- 10.7 Modulation Limit Alignment
- 10.8 Changing to Battery Charger Only Mode
SLR 5000 Series Maintenance and Disassembly/Reassembly
- 11.1 Introduction
- 11.2 Routine Maintenance
- 11.3 Preventive Maintenance
  - 11.3.1 Inspection
  - 11.3.2 Cleaning Procedures
- 11.4 Safe Handling of CMOS and LDMOS Devices
- 11.5 Disassembly
  - 11.5.1 Disassembly – General
  - 11.5.2 Disassembly – Detailed
- 11.6 Assembly and Reassembly
  - 11.6.1 Assembly – Detailed
    - 11.6.1.1 Back Panel Installation

9.3.3

Verifying Receiver Circuitry Procedure

Procedure:

1 Connect equipment as shown in Figure 38: Test Equipment Setup for Verifying Receiver

Circuitry on page 86.

2 Set the Service Monitor to generate a 1.0 μV (-107 dBm) FM signal at the Receiver frequency,

modulated by a 1 kHz tone at 3 kHz deviation for 25/30 kHz channel spacing, or 1.5 kHz

deviation for 12.5 kHz channel spacing. The 1 kHz tone should be audible through the external

speaker. If no audio is heard, suspect the following:

• Faulty Modem Module

• Faulty antenna-to-Receiver preselector RF cable (for the repeater with external metal

preselector)

• Faulty Service Monitor-to-station RF cable

• Faulty Antenna Relay (If installed)

• Faulty Preselector (If installed)

• Rear Panel to Modem Module cable unplugged

• Faulty rear panel to Modem Module Cable

3 If Audio is heard (the audio volume can be adjusted on the rear of the HSN1006), look at the

Oscilloscope window on the Aeroflex 3920 (or a separate O-Scope) and verify that the Audio

level Sine Wave measures between 0.75 to 1.5 Vpp. If not, connect to Tuner and increase the

RX Audio level until this is achieved. If the level cannot be obtained, suspect a faulty Modem.

4 Move the BNC cable from the Scope CH 1 input to the Audio 1 input.

5 Change System Monitor injection signal level to the noted levels in .

6 Measure the Receiver 12 dB SINAD sensitivity.

• If the SINAD level is less than 12 dB, suspect faulty Modem.

7 This completes the Verifying Receiver Circuitry test procedure. If all displays and measurements

are correct, the Receiver circuitry may be considered to be operating properly. Remove test

equipment, restore the repeater to normal service, and (if applicable) return to the

troubleshooting flow chart to resume troubleshooting sequence.

Figure 38: Test Equipment Setup for Verifying Receiver Circuitry

HELP

TAB

SELECT

CANCEL

IFR390I Digital Radio Test Set

TEST

HOLD

CONFIG

UTILS

ENTER

MIC/ ACC GEN T/R ANT

RETURN

TESTPORT CH1 SCOPE CH2 1 2AUDIOINFCTNGEN/DEMOD OUT

ASSIGN

–

4 5 6

HELP

8 9

GEN

Test Box (RLN4460_)

Service Speaker

(HSN1006_)

Aud 1

MT B+

Dummy Load

TxRx

Connect to Scope Ch 1

MN001436A01-AD

Chapter 9: SLR 5000 Series Performance Check or Testing

86 Send Feedback