User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

Table Of Contents

Foreword
- General Safety Precautions
- Computer Software Copyrights
- Document Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
MOTOTRBO SLR 5000 Series Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Warranty
SLR 5000 Series Repeater
- 1.1 Notations Used in This Manual
- 1.2 Description
- 1.3 Operating Features
- 1.4 Frequency Ranges and Power Levels
- 1.5 Specifications
- 1.6 Theory of Operation
- 1.7 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.8 Repeater Model Numbering Scheme
- 1.9 Model Chart
SLR 5000 Series Satellite Receiver
- 2.1 Description
- 2.2 Operating Features
- 2.3 Frequency Ranges
- 2.4 Specifications
- 2.5 Configuration
- 2.6 Basic Station Level Troubleshooting – RDAC and LEDs
- 2.7 Model Chart
SLR 5000 Series Modem
- 3.1 Description
- 3.2 Receiver Subsystem
  - 3.2.1 Specifications
- 3.3 Transmitter Exciter Subsystem
  - 3.3.1 Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 High Stability Reference Block
  - 3.4.2 Audio
- 3.5 Station Control Interface
SLR 5000 Series Power Amplifier
- 4.1 Description
  - 4.1.1 General Description
- 4.2 Input and Output Connections
- 4.3 Frequency Ranges
- 4.4 Specifications
- 4.5 Modem Interface
SLR 5000 Series Power Supply
- 5.1 Description
  - 5.1.1 General Description
- 5.2 Specifications
- 5.3 Power Supply Interface
SLR 5000 Series Front Panel
- 6.1 Description
  - 6.1.1 General Description
- 6.2 Input and Output Connections
- 6.3 Interfaces
  - 6.3.1 Modem Interface
  - 6.3.2 User/Service Interface
    - 6.3.2.1 USB
    - 6.3.2.2 LED Indicators
SLR 5000 Series Back Panel
- 7.1 Description
  - 7.1.1 General Description
- 7.2 Back panel Interfaces
SLR 5000 Series Test Equipment And Service Aids
- 8.1 Recommended Test Equipment
- 8.2 Service Aids
SLR 5000 Series Performance Check or Testing
- 9.1 General
- 9.2 Transmitter Testing
- 9.3 Receiver Testing
- 9.4 Auto Test and Tune Support
SLR 5000 Series Programming and Tuning
- 10.1 Introduction
- 10.2 Customer Programming Software Setup
- 10.3 Reference Oscillator Alignment
  - 10.3.1 Tuning the Reference Oscillator Alignment
- 10.4 Repeater Tuning Setup
- 10.5 Rx Audio Level Set
  - 10.5.1 Tuning the Rx Audio Level Set
- 10.6 Tx Audio Level Set
  - 10.6.1 Tuning the Tx Audio Level Set
- 10.7 Modulation Limit Alignment
- 10.8 Changing to Battery Charger Only Mode
SLR 5000 Series Maintenance and Disassembly/Reassembly
- 11.1 Introduction
- 11.2 Routine Maintenance
- 11.3 Preventive Maintenance
  - 11.3.1 Inspection
  - 11.3.2 Cleaning Procedures
- 11.4 Safe Handling of CMOS and LDMOS Devices
- 11.5 Disassembly
  - 11.5.1 Disassembly – General
  - 11.5.2 Disassembly – Detailed
- 11.6 Assembly and Reassembly
  - 11.6.1 Assembly – Detailed
    - 11.6.1.1 Back Panel Installation

- ETSI TS 102 361-1 Part 1: DMR Air Interface Protocol

- ETSI TS 102 361-2 Part 2: DMR Voice and Generic Services and Facilities

- ETSI TS 102 361-3 Part 3: DMR Packet Data Protocol

- ETSI TS 102 361-4 Part 4: DMR Trunking Protocol

- California Energy Commission (CEC) - Compliant to Title 20 Appliance Efficiency Regulations

when operated in Battery Charger Only mode with Sprinter Battery S12V370. Charge time may

take up to 40 hr.

• AMBE +2

™

Digital VOCODER

• Synthesized Frequency Generation

• Female N-type Antenna Connector (Tx)

• Female BNC Antenna Connector (Rx)

• Ethernet Port (Network)

• Front-mounted USB Port (Service)

• 12 configurable GPIO ports (Digital)

• 4 configurable GPI ports (Analog)

• 2 configurable GPO ports (Analog)

• Power for third-party controllers (1 A)

• 1.5 PPM Frequency Stability (Temperature and 1-Year Aging) (VHF and UHF)

• External Reference Capability

• Switching Power Supply operates from 85–264 VAC (47–63 Hz)

• Multi-Power Source configurable (AC, DC, or AC with Battery Revert)

• Integrated 3 A battery charger

• Station Diagnostic Tests – Fixed Set of Tests run upon Start-up

• Physical Dimensions: 1.75 in. H x 19 in. W x 14.6 in. D (44 x 483 x 370 mm) 1RU

• Weight: 19 lb (8.62 kg) excluding cabinet or other peripheral equipment

Motorola Solutions Network Interface:

• IP Site Connect

• Repeater Diagnostics and Control (RDAC)

• Capacity Plus

• Connect Plus

Third-Party Controller Interface:

• Phone Patch

• Multi-Coded Squelch Interface (Repeater Panel)

• Tone Remote Adapter

• LTR Trunking

• Passport Trunking

• MPT1327 Trunking

NOTICE: The SLR 5000 series repeater only supports the third-party controllers noted above

when it is configured in analog mode. The exception is phone patch in digital mode.

MN001436A01-AD

Chapter 1: SLR 5000 Series Repeater

40 Send Feedback