User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

Table Of Contents

Foreword
- General Safety Precautions
- Computer Software Copyrights
- Document Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
MOTOTRBO SLR 5000 Series Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Warranty
SLR 5000 Series Repeater
- 1.1 Notations Used in This Manual
- 1.2 Description
- 1.3 Operating Features
- 1.4 Frequency Ranges and Power Levels
- 1.5 Specifications
- 1.6 Theory of Operation
- 1.7 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.8 Repeater Model Numbering Scheme
- 1.9 Model Chart
SLR 5000 Series Satellite Receiver
- 2.1 Description
- 2.2 Operating Features
- 2.3 Frequency Ranges
- 2.4 Specifications
- 2.5 Configuration
- 2.6 Basic Station Level Troubleshooting – RDAC and LEDs
- 2.7 Model Chart
SLR 5000 Series Modem
- 3.1 Description
- 3.2 Receiver Subsystem
  - 3.2.1 Specifications
- 3.3 Transmitter Exciter Subsystem
  - 3.3.1 Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 High Stability Reference Block
  - 3.4.2 Audio
- 3.5 Station Control Interface
SLR 5000 Series Power Amplifier
- 4.1 Description
  - 4.1.1 General Description
- 4.2 Input and Output Connections
- 4.3 Frequency Ranges
- 4.4 Specifications
- 4.5 Modem Interface
SLR 5000 Series Power Supply
- 5.1 Description
  - 5.1.1 General Description
- 5.2 Specifications
- 5.3 Power Supply Interface
SLR 5000 Series Front Panel
- 6.1 Description
  - 6.1.1 General Description
- 6.2 Input and Output Connections
- 6.3 Interfaces
  - 6.3.1 Modem Interface
  - 6.3.2 User/Service Interface
    - 6.3.2.1 USB
    - 6.3.2.2 LED Indicators
SLR 5000 Series Back Panel
- 7.1 Description
  - 7.1.1 General Description
- 7.2 Back panel Interfaces
SLR 5000 Series Test Equipment And Service Aids
- 8.1 Recommended Test Equipment
- 8.2 Service Aids
SLR 5000 Series Performance Check or Testing
- 9.1 General
- 9.2 Transmitter Testing
- 9.3 Receiver Testing
- 9.4 Auto Test and Tune Support
SLR 5000 Series Programming and Tuning
- 10.1 Introduction
- 10.2 Customer Programming Software Setup
- 10.3 Reference Oscillator Alignment
  - 10.3.1 Tuning the Reference Oscillator Alignment
- 10.4 Repeater Tuning Setup
- 10.5 Rx Audio Level Set
  - 10.5.1 Tuning the Rx Audio Level Set
- 10.6 Tx Audio Level Set
  - 10.6.1 Tuning the Tx Audio Level Set
- 10.7 Modulation Limit Alignment
- 10.8 Changing to Battery Charger Only Mode
SLR 5000 Series Maintenance and Disassembly/Reassembly
- 11.1 Introduction
- 11.2 Routine Maintenance
- 11.3 Preventive Maintenance
  - 11.3.1 Inspection
  - 11.3.2 Cleaning Procedures
- 11.4 Safe Handling of CMOS and LDMOS Devices
- 11.5 Disassembly
  - 11.5.1 Disassembly – General
  - 11.5.2 Disassembly – Detailed
- 11.6 Assembly and Reassembly
  - 11.6.1 Assembly – Detailed
    - 11.6.1.1 Back Panel Installation

Chapter 1

SLR 5000 Series Repeater

1.1

Notations Used in This Manual

Throughout the text in this publication, there are WARNING, CAUTION, and Note notations. These

notations are used to emphasize that safety hazards exist, and due care must be taken and observed.

NOTICE: An operational procedure, practice, or condition which is essential to emphasize.

CAUTION: CAUTION indicates a potentially hazardous situation which, if not avoided, might

result in equipment damage.

WARNING: WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or injury.

Symbol indicates areas of the product that pose potential burn hazards.

1.2

Description

The Motorola Solutions SLR 5000 Series Repeater provides a modular, flexible analog and digital

station designed for today's communication systems and for the future.

The station is available for use in these configurations:

• Analog Conventional

• Digital (MOTOTRBO)

- MOTOTRBO DMR Tier 2 Conventional – Single Site

- MOTOTRBO DMR Tier 2 Conventional – IP Site Connect

- MOTOTRBO Capacity Plus Trunking

- MOTOTRBO Connect Plus Trunking

- MOTOTRBO Digital Voting

• LTR Trunking

• Passport Trunking

• MPT1327 Trunking

NOTICE: Certain software features enabled through the CPS can be configured with the Online

Help or with a regional representative. Refer to the regional Ordering Guide to determine the

features available within the respective regions.

The SLR 5000 series can either be configured as a stand-alone repeater or as a repeater connected to

a back-end network, as in the case of operating in IP Site Connect mode. As a repeater, it listens on

one uplink frequency, and then re-transmits on a downlink frequency, thus providing the RF interface to

the field subscribers. When configured for analog station operation, the repeater is designed to operate

with most existing analog systems, which enables a smooth migration to the MOTOTRBO system.

When configured for digital operation, the repeater offers additional services. The digital repeater

operates in TDMA mode, which essentially divides one channel into two virtual channels using time

MN001436A01-AD

SLR 5000 Series Repeater

Send Feedback 37