User's Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

100

101

102

103

104

105

Table Of Contents

Foreword
- General Safety Precautions
- Computer Software Copyrights
- Document Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
MOTOTRBO SLR 5000 Series Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Warranty
SLR 5000 Series Repeater
- 1.1 Notations Used in This Manual
- 1.2 Description
- 1.3 Operating Features
- 1.4 Frequency Ranges and Power Levels
- 1.5 Specifications
- 1.6 Theory of Operation
- 1.7 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.8 Repeater Model Numbering Scheme
- 1.9 Model Chart
SLR 5000 Series Satellite Receiver
- 2.1 Description
- 2.2 Operating Features
- 2.3 Frequency Ranges
- 2.4 Specifications
- 2.5 Configuration
- 2.6 Basic Station Level Troubleshooting – RDAC and LEDs
- 2.7 Model Chart
SLR 5000 Series Modem
- 3.1 Description
- 3.2 Receiver Subsystem
  - 3.2.1 Specifications
- 3.3 Transmitter Exciter Subsystem
  - 3.3.1 Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 High Stability Reference Block
  - 3.4.2 Audio
- 3.5 Station Control Interface
SLR 5000 Series Power Amplifier
- 4.1 Description
  - 4.1.1 General Description
- 4.2 Input and Output Connections
- 4.3 Frequency Ranges
- 4.4 Specifications
- 4.5 Modem Interface
SLR 5000 Series Power Supply
- 5.1 Description
  - 5.1.1 General Description
- 5.2 Specifications
- 5.3 Power Supply Interface
SLR 5000 Series Front Panel
- 6.1 Description
  - 6.1.1 General Description
- 6.2 Input and Output Connections
- 6.3 Interfaces
  - 6.3.1 Modem Interface
  - 6.3.2 User/Service Interface
    - 6.3.2.1 USB
    - 6.3.2.2 LED Indicators
SLR 5000 Series Back Panel
- 7.1 Description
  - 7.1.1 General Description
- 7.2 Back panel Interfaces
SLR 5000 Series Test Equipment And Service Aids
- 8.1 Recommended Test Equipment
- 8.2 Service Aids
SLR 5000 Series Performance Check or Testing
- 9.1 General
- 9.2 Transmitter Testing
- 9.3 Receiver Testing
- 9.4 Auto Test and Tune Support
SLR 5000 Series Programming and Tuning
- 10.1 Introduction
- 10.2 Customer Programming Software Setup
- 10.3 Reference Oscillator Alignment
  - 10.3.1 Tuning the Reference Oscillator Alignment
- 10.4 Repeater Tuning Setup
- 10.5 Rx Audio Level Set
  - 10.5.1 Tuning the Rx Audio Level Set
- 10.6 Tx Audio Level Set
  - 10.6.1 Tuning the Tx Audio Level Set
- 10.7 Modulation Limit Alignment
- 10.8 Changing to Battery Charger Only Mode
SLR 5000 Series Maintenance and Disassembly/Reassembly
- 11.1 Introduction
- 11.2 Routine Maintenance
- 11.3 Preventive Maintenance
  - 11.3.1 Inspection
  - 11.3.2 Cleaning Procedures
- 11.4 Safe Handling of CMOS and LDMOS Devices
- 11.5 Disassembly
  - 11.5.1 Disassembly – General
  - 11.5.2 Disassembly – Detailed
- 11.6 Assembly and Reassembly
  - 11.6.1 Assembly – Detailed
    - 11.6.1.1 Back Panel Installation

CAUTION: DO NOT attempt to remove the Chassis ID module as removing it will void

the warranty as well as disabling any purchased software features. Keep the Chassis ID

module installed throughout disassembly.

2 Remove the flex cables connecting the Modem to the Power Amplifier Module and Front Panel.

3 Remove the coaxial able connecting the Modem to the Power Amplifier Module.

4 Gently press the locking clip and pull the “C5” connector from the Modem.

5 Remove the screws from the three cable clamps securing the cables from the power supply to

the fans and modules with a T20 Torx driver and remove the cable clamps from repeater.

6 Remove the two DC power screws from the Power Amplifier Module with a T10 Torx driver.

7 Remove the two DC power screws from the Modem with a T10 Torx driver.

8 Disengage the three connectors from the Power Supply to the three mounted fans with needle

nose pliers or fingers.

Figure 50: Removing Cables

11.5.2.4

Fan Disassembly

Procedure:

1 Press the tab below the fan module until it disengages. See Figure 51: Removing Fan on page

102 for location of tab.

2 Rock the fan module up and away from the frame and remove.

3 Repeat the steps above for the remaining two fan modules.

MN001436A01-AD

Chapter 11: SLR 5000 Series Maintenance and Disassembly/Reassembly

Send Feedback 101