User's Manual
Table Of Contents
- SLR 5000 Series Installation
- 12.1 Pre-Installation Considerations
- 12.2 Mechanical Installation
- 12.3 Electrical Connections
- 12.4 Post Installation Checklist
- 12.5 Installing Repeater Hardware Options
- Appendix A: Accessories
- Appendix B: Replacement Parts Ordering
- Appendix C: Motorola Solutions Service Centers
- Appendix D: SLR 5000 Series Third-Party Controllers
- Appendix F: MOTOTRBO Repeater – EME ASSESSMENT
- Glossary of Terms and Acronyms
- Alert tone
- Analog
- ASIC
- AUX
- Band
- CTCSS
- Clear
- Conventional
- CPS
- Default
- Digital
- DPL
- DSP
- EIA
- ESD
- EU
- FCC
- FM
- Frequency
- FRU
- FSK
- GNSS
- GPIO
- IC
- IF
- I/O
- kHz
- LCD
- LED
- MDC
- MHz
- MISO
- MOSI
- PA
- PC Board
- PFC
- PL
- Programming Cable
- PTT
- Receiver
- Repeater
- RF
- RSSI
- Rx
- SCM
- SELV
- Signal
- SINAD
- SLR
- Spectrum
- SPI
- Squelch
- TOT
- TPL
- Transceiver
- Transmitter
- Trunking
- Tx
- UHF
- USB
- VCO
- VCTCXO
- VHF
- VIP
- VSWR
- WLAN
Appendix D: SLR 5000 Series Third-
Party Controllers
Overview
The SLR 5000 Series Repeater is capable of interfacing to a number of third party controllers via the
four-wire and GPIO/GPI interface afforded by the back panel AUX connector. This section covers the
connections and signal levels between the third party controllers and the repeater, as well as the audio
path configuration needed via CPS. Note that this section is not a substitute for a more comprehensive
instruction detailed in the vendor's manuals of their respective third party controllers.
The third party controllers supported by SLR 5000 Series Repeater are as follows:
• Community Repeater Panel (Zetron Model 38-Max)
• Phone Patch (Zetron Model 30)
• Tone Remote Adapter (Motorola Solutions Model L3276)
• LTR (Trident Model Raider and Marauder)
• Passport (Trident Model NTS) (see Note)
CAUTION: Do not hot swap any of the third party controllers as this could (at a minimum) cause
a malfunction with the repeater.
NOTICE:
The SLR 5000 Series Repeater only support the third party controllers noted above when it is
configured in analog mode. The screen capture below shows the CPS location to configure the
SLR 5000 Series Repeater for analog mode.
If the third party controllers are supplied power by the SLR 5000 Series Repeater, then the SLR
5000 Series Repeater needs to be in a powered off state when establishing (or removing) the
connection to the SLR 5000 Series back panel connector.
Figure 83: CPS Settings to Configure SLR 5000 Series Repeater for Analog Mode
Community Repeater Panel
The SLR 5000 Series Repeater is capable of Multi Coded Squelch through the Zetron Model 38
Repeater Panel. The Model 38 Repeater Panel interconnects to the repeater and provides 38 PL tones
and 22 DPL tones standard.
See Zetron Model 38 Repeater Panel Instruction Manual (supplied with the panel) for panel
specifications, operation, installation, alignment, programming, and repair information.
Figure 84: Model Zetron 38 Repeater Panel
MN001436A01-AD
Appendix D: SLR 5000 Series Third-Party Controllers
Send Feedback 141