User's Manual
Table Of Contents
- Declaration of Conformity
- Important Safety Information
- Software Version
- Computer Software Copyrights
- Getting Started
- Identifying Radio Controls
- Identifying Status Indicators
- Receiving and Making Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber Alias or ID, or Group Alias or ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Permanent Monitor
- Advanced Features
- Radio Check
- Remote Monitor
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Activating or Deactivating Call Ringers for Call Alerts
- Activating or Deactivating Call Ringers for Private Calls
- Activating or Deactivating Call Ringers for Selective Call
- Activating or Deactivating Call Ringers for Text Message
- Activating or Deactivating Call Ringers for Telemetry Status with Text
- Assigning Ring Styles
- Escalating Alarm Tone Volume
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Text Messaging Features
- Analog Message Encode
- Analog Status Update
- Privacy
- IP Site Connect
- Security
- Lone Worker
- Bluetooth
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Changing the Display Mode
- Adjusting the Display Brightness
- Turning Horns/Lights On or Off
- Turning the Public Address System On or Off
- Turning the External Public Address System On or Off
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Turning the LED Indicators On or Off
- Setting Dual Knob Operation Preference
- Language
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Turning the Option Board Feature(s) On or Off
- Identifying Cable Type
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- GPS
- Accessing General Radio Information
- Checking the Firmware Version and Codeplug Version
- Checking the GPS Information
- Keypad Microphone Features
- Using the Keypad
- Additional Advanced Features
- Selecting a Zone by Alias Search
- Initiating a Radio Check by Manual Dial
- Initiating Remote Monitor by Manual Dial
- Making a Private Call by Manual Dial
- Making a Group, Private or All Call with the Programmable Number Key
- Making a Group, Private, Phone or All Call by Alias Search
- Viewing an Entry in the Scan List by Alias Search
- Editing the Scan List by Alias Search
- Storing an Alias or ID from a Call List
- Making a Call Alert by Manual Dial
- Text Messaging
- Dual Tone Multi Frequency (DTMF)
- Security
- Password Lock Features
- Front Panel Configuration (FPC)
- Accessories
- Appendix: Maritime Radio Use in the VHF Frequency Range
- Limited Warranty
- Notes
Advanced Features
English
60
The green LED lights up while the radio is transmitting and
double blinks when the radio is receiving an ongoing privacy-
enabled transmission.
NOTE: Some radio models may not offer this Privacy feature.
Check with your dealer or system administrator for
more information.
Procedure:
Press the programmed Privacy button to toggle privacy on or
off.
OR
Follow the procedure below.
1 g to access the menu.
2 f or h to Utilities and press g to select.
3 f or h to Radio Settings and press g to select.
4 f or h to Privacy.
5 Press g to enable Privacy. The display shows 9 beside
Enabled.
OR
Press
g to disable Privacy. The 9 disappears from beside
Enabled.
If the radio has a privacy type assigned, the secure or unsecure
icon appears on the status bar, except when the radio is
sending or receiving an Emergency call or alarm.
IP Site Connect
This feature allows your radio to extend communication beyond
the reach of a single site, by connecting to different available
sites via an Internet Protocol (IP) network.
NOTE: This feature is not applicable in Capacity Plus.
When the radio moves out of range from one site and into the
range of another, it connects to the new site's base station to
send or receive calls/data transmissions. Depending on your
settings, this is done automatically or manually.
If the radio is set to do this automatically, it scans through all
available sites when the signal from the current site is weak or
when the radio is unable to detect any signal from the current
site. It then locks on to the base station with the strongest
Received Signal Strength Indicator (RSSI) value.
In a manual site search, the radio searches for the next site in
the roam list that is currently in range (but which may not have
the strongest signal) and locks on to it.
NOTE: Each channel can only have either Scan or Roam
enabled, not both at the same time.
Channels with this feature enabled can be added to a particular
roam list. The radio searches the channel(s) in the Members list
during the automatic roam operation to locate the best site.
A Members list supports a maximum of 16 channels (including
the Selected Channel).