User's Manual
Table Of Contents
- Declaration of Conformity
- Important Safety Information
- Software Version
- Computer Software Copyrights
- Getting Started
- Identifying Radio Controls
- Identifying Status Indicators
- Receiving and Making Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber Alias or ID, or Group Alias or ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Permanent Monitor
- Advanced Features
- Radio Check
- Remote Monitor
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Activating or Deactivating Call Ringers for Call Alerts
- Activating or Deactivating Call Ringers for Private Calls
- Activating or Deactivating Call Ringers for Selective Call
- Activating or Deactivating Call Ringers for Text Message
- Activating or Deactivating Call Ringers for Telemetry Status with Text
- Assigning Ring Styles
- Escalating Alarm Tone Volume
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Text Messaging Features
- Analog Message Encode
- Analog Status Update
- Privacy
- IP Site Connect
- Security
- Lone Worker
- Bluetooth
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Changing the Display Mode
- Adjusting the Display Brightness
- Turning Horns/Lights On or Off
- Turning the Public Address System On or Off
- Turning the External Public Address System On or Off
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Turning the LED Indicators On or Off
- Setting Dual Knob Operation Preference
- Language
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Turning the Option Board Feature(s) On or Off
- Identifying Cable Type
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- GPS
- Accessing General Radio Information
- Checking the Firmware Version and Codeplug Version
- Checking the GPS Information
- Keypad Microphone Features
- Using the Keypad
- Additional Advanced Features
- Selecting a Zone by Alias Search
- Initiating a Radio Check by Manual Dial
- Initiating Remote Monitor by Manual Dial
- Making a Private Call by Manual Dial
- Making a Group, Private or All Call with the Programmable Number Key
- Making a Group, Private, Phone or All Call by Alias Search
- Viewing an Entry in the Scan List by Alias Search
- Editing the Scan List by Alias Search
- Storing an Alias or ID from a Call List
- Making a Call Alert by Manual Dial
- Text Messaging
- Dual Tone Multi Frequency (DTMF)
- Security
- Password Lock Features
- Front Panel Configuration (FPC)
- Accessories
- Appendix: Maritime Radio Use in the VHF Frequency Range
- Limited Warranty
- Notes
Advanced Features
English
46
releases the PTT button, indicating the channel is free for
you to respond.
3 Press PTT button to transmit non-emergency voice to the
same group that the Emergency Alarm was targeted to. The
green LED lights up. Your radio remains in the Emergency
mode.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the microphone.
OR
Wait for the PTT Sidetone to finish (if enabled) and
speak clearly into the microphone.
5 Release the PTT button to listen. When the emergency
initiating radio responds, the green LED blinks. You see the
Group Call icon, the group alias or ID, and transmitting radio
alias or ID on your display.
6 Your radio displays the Alarm List.
Emergency voice can only be transmitted by the emergency
initiating radio. All other radios (including the emergency
receiving radio) transmit non-emergency voice.
Sending an Emergency Alarm
This feature allows you to send an Emergency Alarm, a
non-voice signal, which triggers an alert indication on a group of
radios.
Procedure:
1 Press the programmed Emergency On button or the
Emergency footswitch.
2 The display shows Tx Alarm and the destination alias. The
green LED lights up and the Emergency icon appears.
OR
The display shows Tx Telegram and the destination
alias. The LED lights up solid green and the Emergency icon
appears.
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds and the green LED blinks. The
display shows Alarm Sent.
OR
If your radio does not receive an Emergency Alarm
acknowledgement, and after all retries have been
exhausted, a tone sounds and the display shows Alarm
Failed.
4 Radio exits the Emergency Alarm mode and returns to the
Home screen.
If your radio is set to Silent, it does not display any audio or
visual indicators during Emergency mode.