User's Manual
Table Of Contents
- Declaration of Conformity
- Important Safety Information
- Software Version
- Computer Software Copyrights
- Getting Started
- Identifying Radio Controls
- Identifying Status Indicators
- Receiving and Making Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber Alias or ID, or Group Alias or ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Permanent Monitor
- Advanced Features
- Radio Check
- Remote Monitor
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Activating or Deactivating Call Ringers for Call Alerts
- Activating or Deactivating Call Ringers for Private Calls
- Activating or Deactivating Call Ringers for Selective Call
- Activating or Deactivating Call Ringers for Text Message
- Activating or Deactivating Call Ringers for Telemetry Status with Text
- Assigning Ring Styles
- Escalating Alarm Tone Volume
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Text Messaging Features
- Analog Message Encode
- Analog Status Update
- Privacy
- IP Site Connect
- Security
- Lone Worker
- Bluetooth
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Changing the Display Mode
- Adjusting the Display Brightness
- Turning Horns/Lights On or Off
- Turning the Public Address System On or Off
- Turning the External Public Address System On or Off
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Turning the LED Indicators On or Off
- Setting Dual Knob Operation Preference
- Language
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Turning the Option Board Feature(s) On or Off
- Identifying Cable Type
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- GPS
- Accessing General Radio Information
- Checking the Firmware Version and Codeplug Version
- Checking the GPS Information
- Keypad Microphone Features
- Using the Keypad
- Additional Advanced Features
- Selecting a Zone by Alias Search
- Initiating a Radio Check by Manual Dial
- Initiating Remote Monitor by Manual Dial
- Making a Private Call by Manual Dial
- Making a Group, Private or All Call with the Programmable Number Key
- Making a Group, Private, Phone or All Call by Alias Search
- Viewing an Entry in the Scan List by Alias Search
- Editing the Scan List by Alias Search
- Storing an Alias or ID from a Call List
- Making a Call Alert by Manual Dial
- Text Messaging
- Dual Tone Multi Frequency (DTMF)
- Security
- Password Lock Features
- Front Panel Configuration (FPC)
- Accessories
- Appendix: Maritime Radio Use in the VHF Frequency Range
- Limited Warranty
- Notes
Receiving and Making Calls
English
22
Making a Private Call
While you can receive and/or respond to a Private Call
initiated by an authorized individual radio, your radio must
be programmed for you to initiate a Private Call.
You hear a negative indicator tone, when you make a Private
Call via the Menu, Call Log, Contacts list, One Touch Access
button, the programmed number keys, Scroll Up/Down
buttons, or the Volume/Channel Knob if this feature is not
enabled.
Use the Text Message or Call Alert features to contact an
individual radio. See Text Messaging Features on page 50 or
Call Alert Operation on page 43 for more information.
Procedure:
1 Press the Volume/Channel Knob to enter the channel
selection state.
2 Turn the knob to select the channel with the active
subscriber alias or ID.
3 Press the PTT button to make the call. The green LED lights
up. The Private Call icon appears in the top right corner. The
first text line shows the subscriber alias. The second text
line displays the call status.
4 Wait for the Talk Permit Tone to finish (if enabled) and speak
clearly into the microphone.
5 Release the PTT button to listen. When the target radio
responds, the green LED blinks.
6 If the Channel Free Indication feature is enabled, you hear a
short alert tone the moment the target radio releases the
PTT button, indicating the channel is free for you to respond.
Press the PTT button to respond.
OR
If there is no voice activity for a predetermined period of
time, the call ends.
7 You hear a short tone. The display shows Call Ended.
You can also make a Private Call via Contacts (see Making a
Private Call from Contacts on page 36), manually dial a
Private Call (see Making a Private Call by Manual Dial on
page 83) or perform a quick alphanumeric search for the
required target alias via a keypad entry (see Making a Group,
Private, Phone or All Call by Alias Search on page 84).
Making an All Call
This feature allows you to transmit to all users on the channel.
Your radio must be programmed to allow you to use this feature.
Procedure:
1 Press the Volume/Channel Knob to enter the channel
selection state.
2 Turn the knob to select the channel with the active All Call
group alias or ID.