Installation Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

Table Of Contents

Foreword
- Notations Used in This Manual
- General Safety Precautions
- Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
Declaration of Conformity
MOTOTRBO SLR 1000 Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Commercial Warranty
SLR 1000 Repeater
- 1.1 Repeater Description
- 1.2 Repeater Operating Features
- 1.3 Repeater Frequency Ranges and Power Levels
- 1.4 Repeater Specifications
- 1.5 Repeater Theory of Operation
- 1.6 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.7 Repeater Model Numbering Scheme
- 1.8 Repeater Model Chart
SLR 1000 Satellite Receiver
- 2.1 Satellite Receiver Description
- 2.2 Satellite Receiver Operating Features
- 2.3 Satellite Receiver Frequency Ranges
- 2.4 Satellite Receiver Specifications
- 2.5 Satellite Receiver Configuration
- 2.6 Basic Satellite Receiver Level Troubleshooting – RDAC and LEDs
- 2.7 Satellite Receiver Model Chart
SLR 1000 Transceiver Board
- 3.1 Transceiver Board Description
  - 3.1.1 Transceiver Board General Description
  - 3.1.2 Input and Output Connections
    - 3.1.2.1 External On/Off Function
- 3.2 Receiver Subsystem
  - 3.2.1 Receiver Subsystem Specifications
- 3.3 Transmitter Subsystem
  - 3.3.1 Transmitter Subsystem Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 Station Control Audio
  - 3.4.2 Station Control Interface
SLR 1000 Front Panel
- 4.1 Front Panel Description
SLR 1000 Bottom Panel
- 5.1 Bottom Panel Description
- 5.2 Bottom Panel Interfaces and Pin Location
SLR 1000 Test Equipment And Service Aids
- 6.1 Recommended Test Equipment
- 6.2 Service Aids
SLR 1000 Performance Check or Testing
- 7.1 Performance Check or Testing General Description
- 7.2 Transmitter Testing
  - 7.2.1 Required Transmitter Test Equipment
  - 7.2.2 Verifying Transmitter Circuitry
- 7.3 Receiver Testing
  - 7.3.1 Required Receiver Test Equipment
  - 7.3.2 Verifying Receiver Circuitry
SLR 1000 Programming and Tuning
- 8.1 Programming and Tuning Introduction
- 8.2 Radio Management Setup
- 8.3 Repeater Tuning Setup
- 8.4 Tuning the Reference Oscillator
- 8.5 Tuning the Rx Audio Level Set
- 8.6 Tuning the Tx Audio Level Set
- 8.7 Modulation Limit Alignment
  - 8.7.1 Tuning the Modulation Limit (with no Tx Data and no PL)
  - 8.7.2 Verifying the Modulation Limit (with no Tx Data and no PL)
- 8.8 Tuning a Duplexer Module
SLR 1000 Maintenance and Disassembly/Reassembly
- 9.1 Routine Maintenance
- 9.2 Preventive Maintenance
  - 9.2.1 Inspection
  - 9.2.2 Cleaning
- 9.3 Safe Handling of CMOS and LDMOS Devices
- 9.4 Installing a Duplexer
- 9.5 Installing a High-Speed Solid-State Antenna Switch
SLR 1000 Installation
- 10.1 Pre-Installation Considerations
- 10.2 SLR 1000 Repeater Package Contents
- 10.3 Mounting the SLR 1000 Repeater to a Wall or Ceiling
- 10.4 Mounting the SLR 1000 Repeater to a Pole
- 10.5 Electrical Connections
- 10.6 General Bonding and Grounding Requirements
- 10.7 General Cabling Requirements
- 10.8 Post Installation Checklist
Appendix A: Accessories
- A.1 Introduction
Appendix B: Replacement Parts Ordering
- B.1 Basic Ordering Information
- B.2 Motorola Solutions Online
- B.3 Mail Orders
- B.4 Telephone Orders
- B.5 Fax Orders
- B.6 Parts Identification
- B.7 Product Customer Service
Appendix C: Motorola Solutions Service Centers
- C.1 Servicing Information
- C.2 Motorola Solutions Service Center
- C.3 Motorola Solutions Federal Technical Center
- C.4 Motorola Solutions Canadian Technical Logistics Center
Appendix D: SLR 1000 Series Third-Party Controllers
- D.1 Third-Party Controllers Overview
- D.2 Tone Remote Adapter
Appendix E: MOTOTRBO Repeater EME Assessment
- E.1 Executive Summary
- E.2 Device Characteristics
- E.3 Exposure Prediction Model
- E.4 Exposure Limits
- E.5 EME Exposure Evaluation
- E.6 Compliance Boundary Description
- E.7 Product Put In Service
- E.8 References
Glossary of Terms and Acronyms
- Alert tone
- Analog
- ASIC
- AUX
- Band
- CTCSS
- Clear
- Conventional
- CPS
- Default
- Digital
- DPL
- DSP
- EIA
- ESD
- EU
- FCC
- FM
- Frequency
- FRU
- FSK
- GNSS
- GPIO
- IC
- IF
- I/O
- kHz
- LCD
- LED
- MDC
- MHz
- MISO
- MOSI
- PA
- PC Board
- PFC
- PL
- Programming Cable
- PTT
- Radio Management
- Receiver
- Repeater
- RF
- RSSI
- Rx
- SCM
- SELV
- Signal
- SINAD
- SLR
- Spectrum
- SPI
- Squelch
- TOT
- TPL
- Transceiver
- Transmitter
- Trunking
- Tx
- UHF
- USB
- VCO
- VCTCXO
- VHF
- VIP
- VSWR
- WLAN

USB

Type B socket (Device Connection) that supports the USB 2.1 protocol standard. See the following

figure and table for the location of the pins and a listing of the functional characteristics of the

connector pins.

Figure 15: USB Connector

Table 16: USB Connector Callout Legend

Location Pin Assignment Type Signal Characteristics

1 VBUS

USB Physical

Layer

+5 VDC

2 D- 3.6 V differential data

3 D+

4 GND Ground

Ethernet

Fully compliant with IEEE and 802.3 and 802.3u standards. Supports 10Base-T, 100Base-Tx rates, full

duplex, half duplex mode, and flow control. See the following figure and table for the location of the

pins and a listing of the functional characteristics of the connector pins.

MN003557A01-AF

Chapter 5: SLR 1000 Bottom Panel