Installation Manual
Table Of Contents
- Foreword
- General Safety and Installation Standards and Guidelines
- Declaration of Conformity
- MOTOTRBO SLR 1000 Repeater Supplemental Safety and Installation Requirements
- Environmental Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Procedures
- Related Publications
- Summary of Bands Available
- Commercial Warranty
- SLR 1000 Repeater
- SLR 1000 Satellite Receiver
- SLR 1000 Transceiver Board
- SLR 1000 Front Panel
- SLR 1000 Bottom Panel
- SLR 1000 Test Equipment And Service Aids
- SLR 1000 Performance Check or Testing
- SLR 1000 Programming and Tuning
- SLR 1000 Maintenance and Disassembly/Reassembly
- SLR 1000 Installation
- 10.1 Pre-Installation Considerations
- 10.2 SLR 1000 Repeater Package Contents
- 10.3 Mounting the SLR 1000 Repeater to a Wall or Ceiling
- 10.4 Mounting the SLR 1000 Repeater to a Pole
- 10.5 Electrical Connections
- 10.6 General Bonding and Grounding Requirements
- 10.7 General Cabling Requirements
- 10.8 Post Installation Checklist
- Appendix A: Accessories
- Appendix B: Replacement Parts Ordering
- Appendix C: Motorola Solutions Service Centers
- Appendix D: SLR 1000 Series Third-Party Controllers
- Appendix E: MOTOTRBO Repeater EME Assessment
- Glossary of Terms and Acronyms
- Alert tone
- Analog
- ASIC
- AUX
- Band
- CTCSS
- Clear
- Conventional
- CPS
- Default
- Digital
- DPL
- DSP
- EIA
- ESD
- EU
- FCC
- FM
- Frequency
- FRU
- FSK
- GNSS
- GPIO
- IC
- IF
- I/O
- kHz
- LCD
- LED
- MDC
- MHz
- MISO
- MOSI
- PA
- PC Board
- PFC
- PL
- Programming Cable
- PTT
- Radio Management
- Receiver
- Repeater
- RF
- RSSI
- Rx
- SCM
- SELV
- Signal
- SINAD
- SLR
- Spectrum
- SPI
- Squelch
- TOT
- TPL
- Transceiver
- Transmitter
- Trunking
- Tx
- UHF
- USB
- VCO
- VCTCXO
- VHF
- VIP
- VSWR
- WLAN
3 Thread on the nut. Torque to 55 in.-lb to compress the gland and seal to the cable jacket.
Ensure that the barrel connector is fully seated before final tightening of the gland nut.
Return to Process
Electrical Connections
on page 108
10.5.2
Connecting the Indoor Adapter AC Input Power
AC/DC power supplies are available and operate from 100–240 VAC at 47–63 Hz AC input power. A
standard 3-prong line cord is required to connect the power supply to the AC source.
CAUTION: Do not apply AC power to the SLR 1000 Repeater at this time. Make sure that the
circuit breaker associated with the AC outlet is turned OFF.
The DC socket-outlet must be installed near the equipment and must be easily accessible.
Figure 41: SLR 1000 Repeater Bottom Panel Connector Names and Locations on page 109
shows the
DC power inlet connector. Insert the plug into an appropriate grounded outlet.
The AC converter comes with a barrel connector output for the DC power that connects to the
repeater.
Procedure:
1 To seal the cable, thread the cable gland nut, then the cable gland over the barrel connector.
2 Insert the connector into the repeater and then thread in the cable gland. Torque to 55 in.-lb to
compress.
3 Thread on the nut and torque to 55 in.-lb to compress the gland and seal to the cable jacket.
Ensure that the barrel connector is fully seated before final tightening of the gland nut.
Return to Process
Electrical Connections on page 108
10.5.3
Assembling an Outdoor Power Supply
The outdoor power supply provides the power source to an SLR 1000 Repeater that is located
outdoors.
Procedure:
1 Identify the AC and DC locations of the power supply. The AC cable has three wires that are
brown, blue, and green/yellow. The DC cable has two wires that are black and red.
2 Cut the cables to a length of 75mm (3 in.).
3 Strip 15mm (¾ in.) off the jacket.
4 Strip 4mm (¼ in.) off the wires.
5 Attach the AC wires to Joiner A (part no. CN001148A01). Torque to 1.5 in.-lb. See Figure 42:
Attach AC Wires to Joiner A on page 112.
MN003557A01-AF
Chapter 10: SLR 1000 Installation
111