Installation Manual
Table Of Contents
- Foreword
- General Safety and Installation Standards and Guidelines
- Declaration of Conformity
- Declaration of Compliance for the Use of Distress and Safety Frequencies
- MOTOTRBO SLR 1000 Repeater Supplemental Safety and Installation Requirements
- Environmental Information
- Document History
- Contents
- List of Figures
- List of Tables
- List of Procedures
- Related Publications
- Summary of Bands Available
- Commercial Warranty
- SLR 1000 Repeater
- SLR 1000 Satellite Receiver
- SLR 1000 Transceiver Board
- SLR 1000 Front Panel
- SLR 1000 Bottom Panel
- SLR 1000 Test Equipment And Service Aids
- SLR 1000 Performance Check or Testing
- SLR 1000 Programming and Tuning
- SLR 1000 Maintenance and Disassembly/Reassembly
- SLR 1000 Installation
- 10.1 Pre-Installation Considerations
- 10.2 SLR 1000 Repeater Package Contents
- 10.3 Mounting the SLR 1000 Repeater to a Wall or Ceiling
- 10.4 Mounting the SLR 1000 Repeater to a Pole
- 10.5 Electrical Connections
- 10.6 General Bonding and Grounding Requirements
- 10.7 General Cabling Requirements
- 10.8 Post Installation Checklist
- Appendix A: Accessories
- Appendix B: Replacement Parts Ordering
- Appendix C: Motorola Solutions Service Centers
- Appendix D: SLR 1000 Series Third-Party Controllers
- Appendix E: MOTOTRBO Repeater EME Assessment
- Glossary of Terms and Acronyms
- Alert tone
- Analog
- ASIC
- AUX
- Band
- CTCSS
- Clear
- Conventional
- CPS
- Default
- Digital
- DPL
- DSP
- EIA
- ESD
- EU
- FCC
- FM
- Frequency
- FRU
- FSK
- GNSS
- GPIO
- IC
- IF
- I/O
- kHz
- LCD
- LED
- MDC
- MHz
- MISO
- MOSI
- PA
- PC Board
- PFC
- PL
- Programming Cable
- PTT
- Radio Management
- Receiver
- Repeater
- RF
- RSSI
- Rx
- SCM
- SELV
- Signal
- SINAD
- SLR
- Spectrum
- SPI
- Squelch
- TOT
- TPL
- Transceiver
- Transmitter
- Trunking
- Tx
- UHF
- USB
- VCO
- VCTCXO
- VHF
- VIP
- VSWR
- WLAN
Chapter 5
SLR 1000 Bottom Panel
Related Links
Bottom Panel Description on page
57
Bottom Panel Interfaces and Pin Location on page 58
5.1
Bottom Panel Description
The Bottom Panel interface provides the electrical interconnection interface between the SLR 1000
Repeater and the end user’s system.
The Bottom Panel interface includes the connectors necessary to program/configure the repeater,and
interface the repeater to the power system, system controllers, LANs, and other communications and
maintenance equipment.
The following provides a general description, identification of inputs/outputs and how the inputs are
connected and sealed, and a pin-out listing for all connectors, including information on signal names,
functions, and levels of the SLR 1000 Repeater Bottom Panel.
Figure 13: SLR 1000 Repeater Bottom Panel Connector Names and Locations on page 57 shows the
various interface connector locations. Table 14: SLR 1000 Repeater Bottom View Callout Legend on
page 57 lists the connector types and primary functions.
Figure 13: SLR 1000 Repeater Bottom Panel Connector Names and Locations
1 2 3 4 5
Table 14: SLR 1000 Repeater Bottom View Callout Legend
Label Description
1 USB Port Programming Interface
MN003557A01-AF
SLR 1000 Bottom Panel
57