Installation Manual

ManualsBrandsMotorola Solutions ManualsElectronicsNon-Broadcast Transmitter

101

102

103

104

105

106

107

108

109

110

Table Of Contents

Foreword
- Notations Used in This Manual
- General Safety Precautions
- Copyrights
- Disclaimer
- Trademarks
General Safety and Installation  Standards and Guidelines
Declaration of Conformity
Declaration of Compliance for the Use of Distress and Safety Frequencies
MOTOTRBO SLR 1000 Repeater  Supplemental Safety and Installation Requirements
Environmental Information
- Material Content
- Disposal of your Electronic and Electric Equipment
- Disposal Guideline
Document History
Contents
List of Figures
List of Tables
List of Procedures
Related Publications
Summary of Bands Available
Commercial Warranty
- Limited Commercial Warranty
SLR 1000 Repeater
- 1.1 Repeater Description
- 1.2 Repeater Operating Features
- 1.3 Repeater Frequency Ranges and Power Levels
- 1.4 Repeater Specifications
- 1.5 Repeater Theory of Operation
- 1.6 Basic Repeater Level Troubleshooting – RDAC and LEDs
- 1.7 Repeater Model Numbering Scheme
- 1.8 Repeater Model Chart
SLR 1000 Satellite Receiver
- 2.1 Satellite Receiver Description
- 2.2 Satellite Receiver Operating Features
- 2.3 Satellite Receiver Frequency Ranges
- 2.4 Satellite Receiver Specifications
- 2.5 Satellite Receiver Configuration
- 2.6 Basic Satellite Receiver Level Troubleshooting – RDAC and LEDs
- 2.7 Satellite Receiver Model Chart
SLR 1000 Transceiver Board
- 3.1 Transceiver Board Description
  - 3.1.1 Transceiver Board General Description
  - 3.1.2 Input and Output Connections
    - 3.1.2.1 External On/Off Function
- 3.2 Receiver Subsystem
  - 3.2.1 Receiver Subsystem Specifications
- 3.3 Transmitter Subsystem
  - 3.3.1 Transmitter Subsystem Specifications
- 3.4 Station Control Subsystem
  - 3.4.1 Station Control Audio
  - 3.4.2 Station Control Interface
SLR 1000 Front Panel
- 4.1 Front Panel Description
SLR 1000 Bottom Panel
- 5.1 Bottom Panel Description
- 5.2 Bottom Panel Interfaces and Pin Location
SLR 1000 Test Equipment And Service Aids
- 6.1 Recommended Test Equipment
- 6.2 Service Aids
SLR 1000 Performance Check or Testing
- 7.1 Performance Check or Testing General Description
- 7.2 Transmitter Testing
  - 7.2.1 Required Transmitter Test Equipment
  - 7.2.2 Verifying Transmitter Circuitry
- 7.3 Receiver Testing
  - 7.3.1 Required Receiver Test Equipment
  - 7.3.2 Verifying Receiver Circuitry
SLR 1000 Programming and Tuning
- 8.1 Programming and Tuning Introduction
- 8.2 Radio Management Setup
- 8.3 Repeater Tuning Setup
- 8.4 Tuning the Reference Oscillator
- 8.5 Tuning the Rx Audio Level Set
- 8.6 Tuning the Tx Audio Level Set
- 8.7 Modulation Limit Alignment
  - 8.7.1 Tuning the Modulation Limit (with no Tx Data and no PL)
  - 8.7.2 Verifying the Modulation Limit (with no Tx Data and no PL)
- 8.8 Tuning a Duplexer Module
SLR 1000 Maintenance and Disassembly/Reassembly
- 9.1 Routine Maintenance
- 9.2 Preventive Maintenance
  - 9.2.1 Inspection
  - 9.2.2 Cleaning
- 9.3 Safe Handling of CMOS and LDMOS Devices
- 9.4 Installing a Duplexer
- 9.5 Installing a High-Speed Solid-State Antenna Switch
SLR 1000 Installation
- 10.1 Pre-Installation Considerations
- 10.2 SLR 1000 Repeater Package Contents
- 10.3 Mounting the SLR 1000 Repeater to a Wall or Ceiling
- 10.4 Mounting the SLR 1000 Repeater to a Pole
- 10.5 Electrical Connections
- 10.6 General Bonding and Grounding Requirements
- 10.7 General Cabling Requirements
- 10.8 Post Installation Checklist
Appendix A: Accessories
- A.1 Introduction
Appendix B: Replacement Parts Ordering
- B.1 Basic Ordering Information
- B.2 Motorola Solutions Online
- B.3 Mail Orders
- B.4 Telephone Orders
- B.5 Fax Orders
- B.6 Parts Identification
- B.7 Product Customer Service
Appendix C: Motorola Solutions Service Centers
- C.1 Servicing Information
- C.2 Motorola Solutions Service Center
- C.3 Motorola Solutions Federal Technical Center
- C.4 Motorola Solutions Canadian Technical Logistics Center
Appendix D: SLR 1000 Series Third-Party Controllers
- D.1 Third-Party Controllers Overview
- D.2 Tone Remote Adapter
Appendix E: MOTOTRBO Repeater EME Assessment
- E.1 Executive Summary
- E.2 Device Characteristics
- E.3 Exposure Prediction Model
- E.4 Exposure Limits
- E.5 EME Exposure Evaluation
- E.6 Compliance Boundary Description
- E.7 Product Put In Service
- E.8 References
Glossary of Terms and Acronyms
- Alert tone
- Analog
- ASIC
- AUX
- Band
- CTCSS
- Clear
- Conventional
- CPS
- Default
- Digital
- DPL
- DSP
- EIA
- ESD
- EU
- FCC
- FM
- Frequency
- FRU
- FSK
- GNSS
- GPIO
- IC
- IF
- I/O
- kHz
- LCD
- LED
- MDC
- MHz
- MISO
- MOSI
- PA
- PC Board
- PFC
- PL
- Programming Cable
- PTT
- Radio Management
- Receiver
- Repeater
- RF
- RSSI
- Rx
- SCM
- SELV
- Signal
- SINAD
- SLR
- Spectrum
- SPI
- Squelch
- TOT
- TPL
- Transceiver
- Transmitter
- Trunking
- Tx
- UHF
- USB
- VCO
- VCTCXO
- VHF
- VIP
- VSWR
- WLAN

10.4

Mounting the SLR 1000 Repeater to a Pole

Perform this procedure to mount the SLR 1000 Repeater to a pole.

Prerequisites: Obtain the following:

•

PMLN7213_ Pole Mount Kit. Consists of:

- One pole mount bracket

- One ½ in. U-bolt

- Two ½ in. bolts

- Four ½ in. nuts

- Two ½ in. washers

• Four M6 screws (supplied in the repeater package)

• Wall mount bracket (supplied in the repeater package)

• Torque wrench, adjustable wrench, or a ratchet with a 10mm socket

• Four M4 T20 bit screws (for a mounting a power supply, supplied in the repeater package)

When and where to use:

There are two possible options for the pole mount installation:

• Using a U-bolt with two ½ in. washers and four ½ in. nuts for poles with a diameter between 2 –

2.75 in.

• Using two band clamps for poles of any diameter. The band clamps are not included in the pole

mount kit.

Procedure:

1 If using the U-bolt for installation, perform the following actions:

a Thread two of the ½ in. nuts onto the U-bolt.

b Place the U-bolt onto the pole and slide the pole mount bracket onto the U-bolt.

c Slide the wall mount bracket onto the U-bolt, with the receiving slots facing upwards, and

place the two ½ in. washers then the two ½ in. nuts onto the U-bolt, one on each thread.

Torque the outer nuts to 150 in./lb. See Figure 35: U-Bolt and Pole Mount Bracket Assembly

on page 105.

MN003557A01-AF

Chapter

10: SLR 1000 Installation

104