User's Manual
Table Of Contents
- Declaration of Conformity
- Contents
- Important Safety Information
- Firmware Version
- Computer Software Copyrights
- Handling Precautions
- Notes
- How to Use This Guide
- What Your Dealer/System Administrator Can Tell You
- Charging the Battery
- Attaching the Battery
- Attaching the Antenna
- Attaching the Belt Clip
- Attaching the Universal Connector Cover (Dust Cover)
- Attaching the Accessory Connector
- Powering Up the Radio
- Adjusting the Volume
- Radio Controls
- Programmable Buttons
- Accessing the Programmed Functions
- Push-To-Talk (PTT) Button
- Switching Between Conventional Analog and Digital Mode
- Capacity Plus
- Display Icons
- Call Icons
- Advanced Menu Icons
- Mini Notice Icons
- LED Indicator
- Audio Tones
- Indicator Tones
- Making and Receiving Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber ID, or Group ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Monitoring Features
- Radio Check
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Analog Message Encode
- Analog Status Update
- Privacy
- Dual Tone Multi Frequency (DTMF)
- IP Site Connect
- Security
- Lone Worker
- Password Lock Features
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Adjusting the Display Brightness
- Controlling the Display Backlight
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Language
- Turning the LED Indicator On or Off
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- Accessing General Radio Information
- Front Panel Configuration (FPC)
- Accessories
- Batteries and Chargers Warranty
- Limited Warranty
English
53
Stopping an Automatic Site Search
When the radio is actively searching for a new site:
Procedure:
Press the programmed Site Lock On/Off button.
1 A tone sounds and the display shows Site Locked.
2 The LED turns off and the display shows the channel alias.
OR
Procedure:
Use the menu.
1 c to access the menu.
2 < or > to Utilities and press e to select.
3 < or > to Radio Settings and press e to select.
4 < or > to Site Roaming and press e to select.
5 < or > to Lock Site State.
6 Press e to lock site. The display shows 9 beside Enabled.
OR
Press
e to unlock site. The 9 disappears from beside
Enabled.
7 The LED turns off and the radio returns to the Home screen.
The display shows the channel alias.
NOTE: At Step 5, you can also use
< or > to change
the selected option.
Starting a Manual Site Search
Procedure:
Press the programmed Manual Site Roam button and proceed
to Step 6.
OR
Follow the procedure below.
1 c to access the menu.
2 < or > to Utilities and press c to select.
3 < or > to Radio Settings and press c to select.
4 < or > to Site Roaming and press c to select.
5 < or > to Active Search and press c to select.
6 A tone sounds and the display shows Finding Site.
The LED blinks green.
7 If a new site is found, a tone sounds and the LED turns off.
The display shows Site <Alias> Found.
OR
If there is no available site within range, a tone sounds and
the LED turns off. The display shows Out of Range.
OR
If a new site is within range, but the radio is unable to
LKP_NAG-LACR.book Page 53 Tuesday, September 6, 2011 5:01 PM