User's Manual
Table Of Contents
- Declaration of Conformity
- Contents
- Important Safety Information
- Firmware Version
- Computer Software Copyrights
- Handling Precautions
- Notes
- How to Use This Guide
- What Your Dealer/System Administrator Can Tell You
- Charging the Battery
- Attaching the Battery
- Attaching the Antenna
- Attaching the Belt Clip
- Attaching the Universal Connector Cover (Dust Cover)
- Attaching the Accessory Connector
- Powering Up the Radio
- Adjusting the Volume
- Radio Controls
- Programmable Buttons
- Accessing the Programmed Functions
- Push-To-Talk (PTT) Button
- Switching Between Conventional Analog and Digital Mode
- Capacity Plus
- Display Icons
- Call Icons
- Advanced Menu Icons
- Mini Notice Icons
- LED Indicator
- Audio Tones
- Indicator Tones
- Making and Receiving Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber ID, or Group ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Monitoring Features
- Radio Check
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Analog Message Encode
- Analog Status Update
- Privacy
- Dual Tone Multi Frequency (DTMF)
- IP Site Connect
- Security
- Lone Worker
- Password Lock Features
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Adjusting the Display Brightness
- Controlling the Display Backlight
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Language
- Turning the LED Indicator On or Off
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- Accessing General Radio Information
- Front Panel Configuration (FPC)
- Accessories
- Batteries and Chargers Warranty
- Limited Warranty
English
44
Sending an Emergency Alarm
This feature allows you to send an Emergency Alarm, a
non-voice signal, which triggers an alert indication on a group of
radios.
Procedure:
1 Press the programmed Emergency On button.
2 The display shows Tx Alarm and the destination alias. The
LED lights up solid green and the Emergency icon appears.
OR
The display shows Tx Telegram and the destination
alias. The LED lights up solid green and the Emergency icon
appears.
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds and the LED blinks green. The
display shows Alarm Sent.
OR
If your radio does not receive an Emergency Alarm
acknowledgement, and after all retries have been
exhausted, a tone sounds and the display shows Alarm
Failed.
4 Radio exits the Emergency Alarm mode and returns to the
Home screen.
If your radio is set to Silent, it will not display any audio or visual
indicators during Emergency mode.
Sending an Emergency Alarm with Call
This feature allows you to send an Emergency Alarm to a group
of radios. Upon acknowledgement by a radio within the group,
the group of radios can communicate over a programmed
Emergency channel.
Procedure:
1 Press the programmed Emergency On button.
2 The display shows Tx Alarm and the destination alias. The
LED lights up solid green and the Emergency icon appears.
OR
The display shows Tx Telegram and the destination
alias. The LED lights up solid green and the Emergency icon
appears.
3 When an Emergency Alarm acknowledgment is received,
the Emergency tone sounds and the LED blinks green. The
display shows Alarm Sent.
4 Your radio enters the emergency call mode when the
display shows Emergency and the destination group alias.
5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from
your mouth.
6 Press PTT button to make the call. The LED lights up solid
green and the group icon appears on the display.
LKP_NAG-LACR.book Page 44 Tuesday, September 6, 2011 5:01 PM