User's Manual
Table Of Contents
- Declaration of Conformity
- Contents
- Important Safety Information
- Firmware Version
- Computer Software Copyrights
- Handling Precautions
- Notes
- How to Use This Guide
- What Your Dealer/System Administrator Can Tell You
- Charging the Battery
- Attaching the Battery
- Attaching the Antenna
- Attaching the Belt Clip
- Attaching the Universal Connector Cover (Dust Cover)
- Attaching the Accessory Connector
- Powering Up the Radio
- Adjusting the Volume
- Radio Controls
- Programmable Buttons
- Accessing the Programmed Functions
- Push-To-Talk (PTT) Button
- Switching Between Conventional Analog and Digital Mode
- Capacity Plus
- Display Icons
- Call Icons
- Advanced Menu Icons
- Mini Notice Icons
- LED Indicator
- Audio Tones
- Indicator Tones
- Making and Receiving Calls
- Selecting a Site
- Selecting a Zone
- Selecting a Radio Channel, Subscriber ID, or Group ID
- Receiving and Responding to a Radio Call
- Making a Radio Call
- Stopping a Radio Call
- Talkaround
- Monitoring Features
- Radio Check
- Scan Lists
- Scan
- Vote Scan
- Contacts Settings
- Call Indicator Settings
- Call Log Features
- Call Alert Operation
- Emergency Operation
- Analog Message Encode
- Analog Status Update
- Privacy
- Dual Tone Multi Frequency (DTMF)
- IP Site Connect
- Security
- Lone Worker
- Password Lock Features
- Notification List
- Utilities
- Turning the Radio Tones/Alerts On or Off
- Setting the Tone Alert Volume Offset Level
- Turning the Talk Permit Tone On or Off
- Setting the Power Level
- Adjusting the Display Brightness
- Controlling the Display Backlight
- Setting the Squelch Level
- Turning the Introduction Screen On or Off
- Language
- Turning the LED Indicator On or Off
- Turning the Voice Operating Transmission (VOX) Feature On or Off
- Voice Announcement
- Call Forwarding
- Menu Timer
- Analog Mic AGC
- Digital Mic AGC
- Intelligent Audio
- Accessing General Radio Information
- Front Panel Configuration (FPC)
- Accessories
- Batteries and Chargers Warranty
- Limited Warranty
English
43
Emergency Operation
An Emergency Alarm is used to indicate a critical situation. You
are able to initiate an Emergency at any time on any screen
display even when there is activity on the current channel.
Your dealer can set the duration of a button press for the
programmed Emergency button, except for long press, which is
similar with all other buttons:
• Short press – Between 0.05 seconds and 0.75 seconds
• Long press – Between 1.00 second and 3.75 seconds
The programmed Emergency button is assigned with the
Emergency On/Off feature. Check with your dealer for the
assigned operation of the Emergency button.
If short press the programmed Emergency button is assigned
to turn on the Emergency mode, then long press the
programmed Emergency button is assigned to exit the
Emergency mode.
If long press the programmed Emergency button is assigned to
turn on the Emergency mode, then short press the programmed
Emergency button is assigned to exit the Emergency mode.
NOTE: Side Button 1 or Side Button 2 can be programmed as
the Emergency Button.
Your radio supports three Emergency Alarms:
• Emergency Alarm
• Emergency Alarm with Call
• Emergency Alarm with Voice to Follow
In addition, each alarm has the following types:
• Regular – Radio transmits an alarm signal and shows audio
and/or visual indicators.
• Silent – Radio transmits an alarm signal without any audio or
visual indicators. Radio receives calls without any sound
through the radio’s speaker, until you press the PTT button to
initiate the call.
• Silent with Voice – Radio transmits an alarm signal without
any audio or visual indicators, but allow incoming calls to
sound through the radio’s speaker.
Only ONE of the Emergency Alarms above can be assigned to
the programmed Emergency button.
LKP_NAG-LACR.book Page 43 Tuesday, September 6, 2011 5:01 PM