Installation Manual

MN003109A01_aa
Standard Configurations Speaker 2-37
4. Put the control head face down on a clean, flat surface to avoid damaging it. Do not touch the
o-ring on the back housing.
5. Carefully disconnect the speaker connector from the circuit board as shown in Figure 2-42.
Figure 2-42. Disconnecting the Speaker Connector
6. Reattach the front housing assembly to the back housing assembly as shown in Figure 2-43.
Make sure that the flex is returned to its original position and that the o-ring on the back
housing assembly is not pinched.
Figure 2-43. Reattaching the Control Head
7. Secure the front housing assembly back to the back housing assembly with four new screws
using the Torx T-20 bit as shown in Figure 2-43. Apply 9 in. lbs. torque for each screw.
D
g a
g a
is returnis retur
not pinched.not pinched
aft
Draft
raft
Draf
Dr
Dra
Dra
Dra
Dra
Dra
Dra
Dra
Draf
r
r
ra
ra
ra
ra
ra
ft
ft
ft
ft
ft
ft
ra
ra
ra
a
raft
af
af
af
af
af
ft
ft
af
af
f
af
ft
ft
af
ft
a
ft
ft
af
ft
af
a
ft
af
a
af
ft
af
ft
a
aft
aft
af
ft
a
f
ft
ft
ft
ft
ft
f
a
a
f
f
a
f
a
a
a
f
f
a
f
a
a
a
raft
a
aft
a
aft
af
af
aft
a
af
ft
ft
ra
a
ft
a
ra
ft
ft
ft
f
f
ft
f
aft
f
aft
f
aft
ft
ft
f
ft
ft
f
ft
t
ft
t
t
t
ft
ft
ft
ft
ft
ft
ft
ft
ft
ft
t
ft
ft
ft
ft
ft
t
aft
ft
ft
ft
t
ft
ft
aft
t
ft
ft
t
ft
ft
ft
t
ft
t
t
ft
ra
ft
ft
t
ft
ft
ft
ft
t
ft
ft
a
t
t
t
t
t
t
D
a
ft
ft
r
ra
ra
r
a
f
f
f
f
f
f
f
f
f
af
a
af
a
af
f
ft
ft
ft
ft
f
f
f
f
f
t
t
t
ft
ft
ft
ft
ft
ft
ft
ft
ft
f
t
ft
ft
ft
t
t
t
ft
ft
ft
t
t
t
t
t
t
ft
ft
ft
ft
ft
ft
a
a
a
D
ra
ft
ft
ft
ft
ft
ft
ft
t
ft
t
t
ft
ft
t
t
t
ft
ft
t
t
t
t
ft
ft
ft
ft
ft
ft
t
D
ft
ft
ra
ra
ra
r
r
ra
ra
ra
a
ra
ra
a
ra
af
ft
ft
af
raf
ra
ra
r
a
a
a
raf
af
raf
a
a
a
ra
a
t
D
aft
raft
ft
ft
ft
ft
f
f
af
af
a
a
t
t
t
t
t
ft
ft
f
ft
f
f
af
af
a
a
a
a
af
f
f
f
f
f
f
ft
t
ft
ft
t
t
t
a
af
ft
ft
ft
ft
ft
ft
ft
f
t
ft
ft
a